Search Documents

By J. Gordon Parr, D. H. Polonis

The formation and subsequent decomposition of metastable phases in Ti-Ni alloys containing up to 11 pet (atomic) Ni have been studied. The decomposition of a completely retained ß phase and of a completely transformed 8 phase in a 6 pet alloy has been followed by X-ray diffraction and metallographic methods and by hardness determinations made during the process. The possible mechanisms of the reactions are discussed. PREVIOUS investigations of the Ti-Ni system have usually been limited to phase diagram studies; but little attention has been given to metastable phases and tempering processes. These are important, however, since equilibrium conditions are rarely achieved—nor, perhaps, are they desired—in practice. Up to the present time the available transformation data for titanium alloys appear to be restricted to isothermal transformation curves for selected binary and ternary systems. No quantitative studies have been made of the mechanism by which equilibrium is approached. Several independent investigations have been carried out to determine the Ti-Ni phase diagram. Early work by Wallbaum' and later by Long et al.' produced tentative phase diagrams which were not representative of true binary conditions, since the alloys were contaminated with oxygen and nitrogen. The most recent diagram (Fig. 1) is due to Margolin et al.," and a slight modification of the a + ß/ß boundary (shown dotted) has been proposed by McQuillan.' The structure of the phase Ti,Ni was shown by Duwez and Taylor" to be face-centered-cubic, with 96 atoms per structure cell. The formation of a martensitic ß phase (close-packed-hexagonal) in Ti-Ni alloys has generally been observed when specimens of low nickel content are rapidly cooled from the 0 (body-centered-cubic) range. Margolin et al. reported an increasing tendency for P to be retained in lump specimens as the nickel content increases. McQuillan' has studied the effect on the microstructure of delay time in quenching, and has reported the formation of pro- eutectoid a precipitate in a quenched hypoeutectoid alloy. In a previous study of Ti-Fe alloys," experiments were made on powder specimens produced by filing alloy ingots. Techniques were devised for the preparation and heat treatment of alloys, and X-ray diffraction methods were used both for structure determinations and phase ratio estimations. A similar approach has been made in this study of Ti-Ni alloys. Experimental Methods Ten alloys ranging from 0.25 pet to 18 pet Ni* * All compositions are in atomic percentages unless otherwise stated. were prepared from iodide titanium bar stock (hardness Rf 72) and Johnson-Matthey spectrographic standard nickel by levitation melting.' As a check

Jan 1, 1957

By D. O. Hobson, J. O. Stiegler, C. J. McHargue

The effects of alloy composition, deformation temperature, heal treatment, ad inlerstilial contamination on the occurrence of deformation twins were studied. The twinning transition temperature varied with composition and was a maximuni of 140°C for the 40 pcl V composition. Tire remperature range of the transition was very narrow. Alloys of 20 to 70 pet V could he cold-rolled and exhibited profuse twinning. The alloys which did not twin at room temperature (10, 80, and 90 pel V) could plot be cold-rolled. Oxygen additions systematically lowered the transition temperatures for all vanadium contents. The transition temperature for a 30 pet V alloy increased with annealing temperature, apparently due to changes in dislocation density and configuration. Twinning did not nucleate fracture in any specimen in the 20 to 60 pet V composition range. THERE is great current interest in the refractory metals and alloys as structural materials. An important factor in considering the ductile-brittle behavior of such materials is the role of mechanical twinning as a deformation mechanism. Mechanical twins have been observed after deformation at low temperatures or at high loading rates in the pure metals iron,1 vanadium,2,3 columbium,4,5 tantalum,6 Chromium,7 molybdenum,8 and tungsten.9 Binary alloys in which mechanical twins have been observed include: iron with silicon,10 phosphorous," or aluminum;12 and chromium, molybdenum, or tungsten with rhenium.13-17 The increase in low-temperature ductility obtained by alloying the Group VI-A elements with rhenium is very important with regard to fabricability, and there has been considerable effort to understand the so-called '(rhenium effect". Factors suggested to explain this effect include:'' 1) increase in solubility of interstitial impurities with alloying (electronic effect): 2) changes in the nature of grain boundary phases; 3) changes in interfacial energies of grain boundaries and stacking faults: and 4) promotion of twinning. Although an outstanding characteristic of these alloys is the profuse twinning that accompanies low-temperature deformation, most studies of the rhenium effect have been concerned with the other factors. During recent studies of refractory-metal alloys, it was noted that solid solutions of columbium and vanadium exhibited high hardness and strength at room temperature and elevated temperature and, surprisingly, also showed considerable ductility at room temperature and below. These alloys deformed by twinning at room temperature when subjected to slow loading rates. It appeared that the low-temperature ductility resulted at least in part from the relaxation of stresses by twinning in a system where slip is difficult. The reason for enhanced twinning behavior in some bee solid-solution alloys is unknown. There have been suggestions18,19 that, as in fee alloys, the

Jan 1, 1965

By R. Ehrlich, F. E. Crane

A consolidated porous medium is mathematically modeled by networks of irregularly shaped, interconnected pore channels. Mechanisms are described that form residual saturations during immiscible displacement both by entire pore channels being bypassed and by fluids being isolated by the movement of an interface within individual pore channels. This latter mechanism is shown to depend strongly on pore channel irregularity. Together, these mechanisms provide an explanation for the drainage-imbibition-hysteresis effect. The calculation of steady-state relative permeabilities, based on a pore-size distribution obtained from a Berea sandstone, is described. These relative permeability curves agree qualitatively with curves that are generally accepted to be typical for highly consolidated materials. In situations where interfacial effects predominate over viscous and gravitational effects, the following conclusions are reached. 1. Relative permeability at a given saturation is everywhere independent of flow rate. 2. Relative permeability is independent of viscosity ratio everywhere except at very low values of wetting-phase relative permeability. 3. Irreducible wetting-phase saturation following steady-state drainage decreases with increasing ratio of nonwetting- to wetting-phase viscosity. 4. lrreducible wetting-phase saturation following unsteady-state drainage is lower than fir steady-state drainage. 5. Irreducible nonwetting-phase saturation 101lowing imbibition is independent of viscosity ratio, whether or not the imbibition is carried out under steady- or unsteady-state conditions. Experiments qualithtiveIy verify the conclusions regarding unsteady-state residual wetting-phase saturation. Implications of these conclusions are discussed. INTRODUCTION Natural and artificial porous materials are generally composed of matrix substance brought together in a more or less random manner. This leads to the creation of a network of interconnected pore spaces of highly irregular shape. Since the geometry of such a network is impossible to describe, we can never obtain a complete description of its flow behavior. We can, however, abstract those properties of the porous medium pertinent to the type of flow under consideration, and thus obtain an adequate description of that flow. Thus, the Kozeny-Carmen equation, by considering a porous medium as a bundle of noninterconnecting capillary tubes, provides an adequate description of single-phase flow. With the addition of a saturation-dependent tortuosity parameter in two-phase flow to account for flow path elongation, the Kozeny-Carmen equation has been used to predict relative permeabilities for the displacement of a wetting liquid by a gas. 1-5 It has long been recognized that relative permeability depends not only on saturation but also on saturation history as we11.6,7 Naar and Henderson8 described a mathematical model in which differences between drainage and imbibition behavior are explained in terms of a bypassing mechanism by which oil is trapped during imbibition. Fatt9 proposed a model for a porous medium that consisted of regular networks of cylindrical tubes of randomly distributed radii. From this he calculated the drainage relative permeability curves. Moore and slobod,10 Rose and Witherspoon,11 and Rose and Cleary12 each considered flow in a pore doublet (a parallel arrangement of a small and large diameter cylindrical capillary tube). They concluded that, because of the different rates of flow in each tube, trapping would occur in one of the tubes; the extent of which would depend upon viscosity ratio and capillary pressure. They limited

Jan 1, 1970

By John Birkinbine

(New Haven 'Meeting, February, 1909.) AWAKENED public interest in efforts to conserve natural resources will certainly be appreciated by the members of the American Institute of Mining Engineers, and a discussion upon conservation may well form a part of one of the Institute meetings, for the records of papers and discussions which appear in the 38 volumes of its Transactions are replete with evidence of effort's in this direction. Every process which reduces the fuel consumed or the power applied per unit of product; every utilization of waste material, or employment of that formerly rejected, to obtain something of value ; every feature of construction or operation which lessens the labor required or increases the output per employee, is an advance in the direction of true conservation. This may not appear from the records of late conferences or from published articles, in which the effort seems to be concentrated upon reducing the consumption and presenting to the people of the country estimates of exhaustion of natural resources. I rejoice in the awakening of public interest in a matter so important for the present and future welfare of our nation; I appreciate the possibility of much good following conferences of the Governors and delegates from various States and from national societies; and I recognize the interdependence, not only of different States, but of contiguous nations. In fact, the marvelous development of transportation by land and by water, and the decreasing rates at which commodities can be moved great distances, have in many cases practically obliterated geographical boundaries, and nearly every country on the globe can either market its product in other lands or draw upon them for raw or manufactured materials ; hence, conservation is an international subject.

Apr 1, 1909

The American Museum of Safety has installed a large collection of exhibits at 18 West 24th St., New York City, and extends a cordial invitation to the members of the Institute to visit this exhibition. The Museum is open daily from 9 am. until 5 p.m., and special arrangements will be made for the admission of a large party in the evening. The exhibition covers all phases of industrial and general safety, and also the important questions of sanitation and hygiene.

Jan 2, 1917

By Robert B Sosman

The relative temperature distribution within a coke oven and among the ovens in a battery can be obtained automatically for the operator's guidance by sighting a total-radiation pyrometer on the face of the coke as it is pushed out, and recording the surface temperature. Keeping the instrument clean and keeping its view of the coke unobstructed by smoke and dust are the principal problems. Typical records from three plants are presented in this paper, showing that the temperature patterns are reproducible. Development OF Method The method of coke pyrometry described in this paper was introduced in 1936 by E. A. Lee, then Assistant Superintendent, now Superintendent, of the Coke Plant at Lorain Works, National Tube Co., Lorain, Ohio. At the request of the Coke Committee of the United States Steel Corporation, the Research Laboratory of the Corporation undertook to adapt the method to the somewhat different conditions met with at the Gary Works of the Carnegie-Illinois Steel Corporation, Gary, Ind., and at the Clairton Works of the same Corporation at Clairton, Pa. This work was done in cooperation with the Leeds and Northrup Co. of Philadelphia and later with the Brown Instrument Co. Division of Minneapolis-Honeywell Regulator Co., Philadelphia. We of the Research Laboratory wish to express our appreci- ation of the courtesies extended by Mr. Lee, by A. N. Cole, Superintendent of the Gary coke plant, and by D. P. Finney, Assistant General Superintendent in charge of coke-plant operations at Clairton. We are also indebted to the instrument companies for the loan of a part of the equipment. At Gary and Clairton the instruments were installed and various experiments were made by J. W. Bain, of the Research Laboratory of the United States Steel Corporation. Pyrometry of Coke The coke inside a by-product oven is almost completely inaccessible to pyro-metric instruments. The temperature in the walls can conceivably be measured with thermocouples, but the atmosphere is usually strongly reducing, a condition well known to be destructive to the accuracy of the customary high-temperature couples. In some plants, periodic readings are taken with an optical pyrometer sighted into the top of the combustion flues. This is a useful measure for safety and general control, as it tends to prevent the damage that would result from overheating of the ovens. It does not, however, tell much about the temperature of the coke itself, because of the continually changing gradient in the wall between the coke and the combustion chamber. The best indication of the temperature of the coke itself must therefore be obtained by observation of the product as it is pushed out of the oven. The human eye is very sensitive to variations in brightness of a surface, and particularly to differences in brightness over a continuous hot surface.

Jan 1, 1943

By Robert B. Sosman

The relative temperature distribution within a coke oven and among the ovens in a battery can be obtained automatically for the operator's guidance by sighting a total-radiation pyrometer on the face of the coke as it is pushed out, and recording the surface temperature. Keeping the instrument clean and keeping its view of the coke unobstructed by smoke and dust are the principal problems. Typical records from three plants are presented in this paper, showing that the temperature patterns are reproducible. Development OF Method The method of coke pyrometry described in this paper was introduced in 1936 by E. A. Lee, then Assistant Superintendent, now Superintendent, of the Coke Plant at Lorain Works, National Tube Co., Lorain, Ohio. At the request of the Coke Committee of the United States Steel Corporation, the Research Laboratory of the Corporation undertook to adapt the method to the somewhat different conditions met with at the Gary Works of the Carnegie-Illinois Steel Corporation, Gary, Ind., and at the Clairton Works of the same Corporation at Clairton, Pa. This work was done in cooperation with the Leeds and Northrup Co. of Philadelphia and later with the Brown Instrument Co. Division of Minneapolis-Honeywell Regulator Co., Philadelphia. We of the Research Laboratory wish to express our appreci- ation of the courtesies extended by Mr. Lee, by A. N. Cole, Superintendent of the Gary coke plant, and by D. P. Finney, Assistant General Superintendent in charge of coke-plant operations at Clairton. We are also indebted to the instrument companies for the loan of a part of the equipment. At Gary and Clairton the instruments were installed and various experiments were made by J. W. Bain, of the Research Laboratory of the United States Steel Corporation. Pyrometry of Coke The coke inside a by-product oven is almost completely inaccessible to pyro-metric instruments. The temperature in the walls can conceivably be measured with thermocouples, but the atmosphere is usually strongly reducing, a condition well known to be destructive to the accuracy of the customary high-temperature couples. In some plants, periodic readings are taken with an optical pyrometer sighted into the top of the combustion flues. This is a useful measure for safety and general control, as it tends to prevent the damage that would result from overheating of the ovens. It does not, however, tell much about the temperature of the coke itself, because of the continually changing gradient in the wall between the coke and the combustion chamber. The best indication of the temperature of the coke itself must therefore be obtained by observation of the product as it is pushed out of the oven. The human eye is very sensitive to variations in brightness of a surface, and particularly to differences in brightness over a continuous hot surface.

Jan 1, 1943

By Thomas T. Read

AT this time of the year, engineering schools are releasing a group of young men who probably are, on the average, in much the same attitude of mind as a person arriving at the terminal station of a railway journey; namely, of having a general idea of his objective, but having to make a decision as to just where he is going and how best to get there. The man leaving the train can at first follow the crowd, but it soon breaks up, as one goes one way and one another, until he has to choose his own course. The recent graduate may do the equivalent of following the crowd by accepting the first position offered, but this only postpones a decision as to where he is going and how best to get there. So many young engineers ask for advice as to what to do that the following statement has been prepared as an attempt to make a general answer to such queries. The engineer taking his first job should realize two fundamental relations. The first is that in electing to be an engineer he has elected to be a hired man. A consulting engineer has more freedom than a man on a regular pay roll, but he is also a hired man; hired for briefer periods at a relatively high rate, but under the necessity of simultaneously doing his consulting work and developing new retainers. There is nothing derogatory in being a hired man (all doctors, lawyers and clergymen are hired men), but the tardy realization that he is one seems to give many an engineer a mental jolt that can be avoided if he accepts it from the beginning.

Jan 1, 1926

By Danforth R. Hale

Minerals for electronic and optical uses divide easily into two sections: (1) quartz and (2) minerals other than quartz. Quartz Quartz, having a great usefulness discovered by the radio communication enthusiasts about 1918, has become a subject of amazingly expanded interest in the U.S. over the past decade as a man-made mineral and a $3 million crystal-growing business. An economic summary of the commercial growing of quartz crystals has a place in a handbook directed to the mineral engineering industry when it is remembered that quartz crystals have long been an important commercial mineral, and that the raw material for “cultured quartz”- that is to say, quartz crystals grown through the ingenuity of man-is still natural quartz. Nearly all the natural crystals come from Brazil. The larger pieces which meet rigorous standards of quality are used for electronic and, to a lesser extent, optical components. Smaller pieces and fragments are used for vitreous silica. The need for high quality material in quantity led to U.S. government-sponsored research programs in the 1940s that have resulted in the factory growing of beautiful crystals of prescribed shape, size, and quality. The development of the cultured quartz crystal is typical of man's success in adapting the product of the mine to increasingly sophisticated uses. A remarkable achievement perhaps, but foreshadowed by experiments in 1908 by Giorgio Spezia (1908), an Italian geologist studying the relative effects of temperature and alkaline environment on the solubility of quartz. Modern radio equipment is most often controlled as to frequency by the presence in the circuit of a separately added "crystal"-the 1918 discovery responsible for the existence and growth of the quartz industry. The "crystal" is quartz, but this component is a carefully oriented and prepared slice from a crystal, but not a crystal as recognized by a rock hound or seen in a museum. How quartz operates to control frequencies is not a proper subject for a handbook on industrial minerals, and references should be consulted (Cady, 1964; Mason, 1964). Quartz belongs to that class of materials called dielectrics: those that do not conduct an electric current but permit electric fields to exist and act across them. Quartz shows the "piezo-electric effect," which means that when a quartz plate is mechanically deformed against its natural stiffness, one of its surfaces becomes negatively charged, the other, positively charged. When the plate is released from the stress quickly, the charges disappear as the plate regains its original shape, but because of mechanical momentum the plate deforms in the opposite direction (to a lesser amount) and the surfaces correspondingly become charged in the opposite direction. By coating the two surfaces thinly with metal and attaching flexible wires, these charges may be brought into an electronic circuit. If the surfaces are suddenly electrically charged by movement of current through the wires, the "converse piezoelectric effect" occurs -the plate deforms. Carry the thought further and it is realized that an alternating current flowing through the wires responds to the mechanical oscillation of the plate and is keyed to this oscillation. By controlling the thickness of the plate its mechanical vibration frequency can bevaried through a wide range. One type of quartz plate, called the AT-cut, having a precisely defined orientation with respect to the crystallographic axes of the crystal, vibrates on a microscopic scale much as a book would deform when placed flat on a table and the top cover moved parallel back and forth with the hand. There are at least 17 other orientations which have been studied, some of

Jan 1, 1975

By R. D. Nelson, S. D. Dahlgren

The conditions of temperature, strain rate, and total strain favoring deformation by grain boundary sliding, slip, or deformation with concurrent recrystallization were evaluated for alpha plutonium. Grain boundary sliding and slip were studied by examining structures formed on polished surfaces with 4.5 pct compressive deformation. The conditions required for recrystallization were determined from compressive deformation us time curves. At 110" C and at a strain rate of 10&apos;per min, deformation was almost exclusively by grain boundary sliding whereas slip was the predominant deformation mode at -10°C and lo-&apos; per min. Defarmation at intermediate tenzperatures and strain rates produced structures showing mixtures of grain boundary sliding and slip. Recrystallization occurred concurrently with deformation only after a critical strain was reached. About 14, 6, and 3 pct strain was required at 105", llO°, and lZO°C, respectively, before recrystallization started, irrespective of the strain rate in the range of lo-&apos;1 to 10&apos;4 per nzin. L HE temperature and strain-rate dependency of the modes of plastic deformation were evaluated for high-purity as-cast alpha plutonium. The techniques used to study slip and grain boundary sliding were similar to those employed previously for alpha plutonium by Bronisz and Gorum,&apos; and spriet.&apos; Recrystallization was investigated using the methods reported by Nelson.3 Bronisz and Gorum&apos; found that slip occurred on more than one slip system at room temperature, and suggested that grain boundary sliding also contributed to the deformation. spriet2 found that deformation was predominantly by slip at room temperature, and observed one to three orientations of slip traces in individual grains. In addition, he deformed polished samples at 10O° C, but concluded that the deformation character of alpha plutonium at 100° C and at room temperature were not essentially different. Several investigators reported that twinning was only occasionally observed.1&apos;2&apos;4 Nelson3 recently found in creep tests that high-purity alpha plutonium would recrystallize concurrently with compressive deformation at temperatures between 25" and 115°C. EXPERIMENTAL PROCEDURE Electrorefined plutonium having less than 300 ppm total impurities was received from Los Alamos Scientific Laboratory in the form of +-in. diarn cast rods. Major impurities were americium, <I00 ppm, and tungsten, (60 ppm. Less than 25 ppm each of other impurities were present. The rods were cut into right half-cylinders 0.35 in. long and 0.25 in. in diam, and the flat faces along the cylinder axes were metal-lographically polished. To avoid loss of the metallo-graphic polish by oxidation, the polished samples were deformed in a silicone fluid heat treating medium contained in a chamber evacuated to a pressure of lo-&apos; torr. Deadweight loading was used to compress the samples between 4.5 and 20 pct at strain rates between 10"4 and lo- &apos; min-&apos;. Strain rates were determined by dividing the total deformation by the elapsed time of the test, even though the strain rate was not constant during deformation. Curves of strain vs time for samples deformed with a constant compressive stress3 show that the strain rate changes by less than a factor of four during the testing of a given sample, which is small compared to the three orders of magnitude change in strain rate investigated. Two samples were loaded into an ordinary metallographic mounting mold and impacted by striking the mold piston with one blow of a 2-lb hammer. Deformation temperatures for the two impact samples were 25" and 90°C. The samples, following deformation, were washed in carbon tetrachloride and their polished and deformed surfaces were immediately inspected metallographi-cally. Subsequently, the deformation structures were replicated with acetate replicating tape for later electron microscope examination, and the samples were then repolished and etched to reveal the microstruc-tures of the deformed metal. Second-stage carbon replicas were prepared from decontaminated acetate replicas using the procedure developed by Miller, Bierlein, and astel.&apos; Additional samples, which were 0.35 in. long by 0.25 in. in diam, were used to obtain constant load deformation vs time curves. These samples were deformed 10 to 20 pct with loads of 15 and 20,000 psi at 120°C; 30, 45, and 55,000 psi at 110°C; and 20 and 30,000 psi at 105°C. Samples were polished and etched to determine whether or not recrystallization or twinning had occurred during deformation. RESULTS AND DISCUSSION The experiments showed that alpha plutonium deforms by grain boundary sliding, slip, and deformation with concurrent recrystallization. Deformation by twinning was insignificant. Metallographic examination of polished and deformed surfaces revealed grain boundary sliding and slip. The start of recrystallization was ascertained from constant load deformation vs time curves. Deformed surface structures of samples compressed 4.5 pct under four different conditions of temperature and strain rate, Fig. 1, show how the deformation mode changes from predominantly grain boundary sliding to predominantly slip with increasing strain rate and decreasing temperature. Deformation at 110°C and 10" 4 min-&apos;, Fig. l(a), was predominantly by grain boundary sliding. Only a few slip traces can be seen in Fig. l(a).

Jan 1, 1969

By L. C. Raymond

Valuations in the mineral industry differ from those of other enterprises because mines and oil wells have a definite life so cannot be considered a perpetuity. This requires that in any mineral-property evaluation the recovery of invested capital is necessary during the life of the property. Capital write-offs for nonextractive industries are assumed to be continuously plowed back to sustain the operation and produce yields on the capital invested. The extractive or mineral industry, however, generally attempts to return to the investor both interest and principal during the life of a property. Normally this is done currently and the dividend includes both items. Where the mineral property possesses large reserves and the life factor approximates a perpetuity, the return on investment is generally comparable to that of industrial stocks. The valuation of a mineral property, at best, is based on educated estimates and judgment factors. This is particularly true as it relates to estimating selling prices over a long term or assessing the quality of management. Also, it is possible to make various assumptions as to rapidity of working out the deposit, varying time for start-up of operations, varying earning rates, so as to obtain different results with the same basic facts. Thus it is not surprising that two engineers, irrespective of their abilities, may not agree exactly even when given the same facts, but their results should be close enough to be used in establishing a fair value for trading purposes. The valuation is no better than the source of basic data and the soundness of judgment factors. Fundamentally the basic principles of mineral valuation are similar for base metals, sulfur, oil, or any other mineral. Each mineral, however, requires an engineer to have a knowledge of such factors as its occurrence, distribution, mining and processing methods, and marketing problems in order to gather and analyze all the facts and data that have a bearing on the earning potential of the property. Present Value of a Mineral Property In essence the present value of a mineral property is a sum of money in today&apos;s dollars that future income from the property are worth. It differs from the total anticipated earnings by the amount of the interest that the unrecouped investment could be expected to earn during the period of recoupment. Thus, if one could accurately estimate what a mineral property will earn during its life, after deducting all operating, administrative, capital, interest, and tax charges, the determination of present value would be a relatively simple mathematical calculation. Normally, where the expected life of the mineral property extends beyond 20 or 25 years, the discounted value of earnings beyond this period is relatively small. The petroleum industry generally discounts the annual cash flow of an operation rather than earnings since, for tax-saving purposes, earnings are kept

Jan 1, 1976

By C. A. Heiland

For a long time it has been known that it is possible to deduce conclusions about the physical constitution of the interior of the earth from the records of natural earthquakes obtained by stationary seismographs. In view of this fact it is surprising how late, relatively speaking, geologic prospecting by seismic methods has been taken up, although the first suggestion was made 40 years ago- that travel-time curves of artificial explosions might be used for the study of the change of the velocity of seismic waves as depth. Further suggestions of practical applications of artificial explosions for geologic purposes were made by Belar,2 by von dem Borne,3 by Benndorf4 and by Galitzin,5 but it was not until 1919 that Mintrop obtained. a patent on the seismic prospecting method which he has applied commercially on a large scale ever since. Dr. Mintrop came to this country with his method at about 1923. Since that time, several. American oil companies have developed seismographs of the mechanical type for the vertical component similar to that of Mintrop&apos;s (Humble Oil Co., Dr. Ricker). Other consulting geophysical companies designed other types of seismic devices, the simplest of them for the recording of the first impulse being the geophone (McCollum Geophone Co.). The galvanometric recording method as first proposed by Galitzin is being used (Geophysical Research Corpn.?) and use is being made even of the piezoelectric properties of crystals for portable seismographs (F. Rieber).. There is such an enormous variety of all kinds of portable seismographs, vibrographs, accelerographs, etc., that it is difficult to decide just what kind is preferable. Unfortunately, nothing has been published as yet about American designs of portable seismographs, except the Wood Anderson torsion-seismometer. After Mintrop&apos;s design of portable seismographs, other constructions were made.

Jan 1, 1928

By C. A. Stickels

In a recent paper, Held1 showed that rolling conditions can have a marked effect on the volume fraction of surface texture produced in low-carbon steel. This variation in rolling texture is reflected in the recrys-tallization texture and affects the plastic properties of the annealed sheet. The fact that roll friction can influence the surface deformation texture in iron and steel has been known for some time;&apos;= but the magnitude of the effect has never been shown quite so clearly before. The analogous effect during wire drawing has been recognized for many year.4 Dillamore and Roberts5 examined surface textures in warm- and cold-rolled aluminum and copper. They found that when a surface texture was present it could be described as the interior texture rotated about the transverse sheet direction. The angle of rotation was a function of the type of lubrication, the amount of reduction per pass, and the temperature of rolling. The purpose of the present note is to show that surface textures in cold-rolled iron can also be described as interior textures rotated about the transverse sheet direction. Vacuum-melted electrolytic iron* was straight- rolled 90 pct at room temperature in a two-high rolling mill with 5-in.-diam rolls. Two rolling procedures were used: a) no lubrication with reductions of about 0.035 in. per pass, and b) heavy lubrication with lano-line and reductions of about 0.002 in. per pass. The final sheet thickness was 0.030 in. (110) pole figures were determined by transmission through specimens taken from the sheet surface and sheet midplane. The surface texture of the sheet cold-rolled according to procedure a is shown in Fig. l.* The shapes of the low-intensity contour lines indicate that the texture can be described as a partial fiber texture with a (110) fiber axis normal to the sheet. The approximate range of orientstions present is (011)[211] — (0ll)[100] — (011)[211]. This range of orientations is what one would obtain by rotating the interior texture 90 deg about the transverse sheet direction. The intensity of (110) and (222) reflections from planes parallel to the surface was measured after removing metal from the surface by chemical polishing. The surface texture here was confined to the outer

Jan 1, 1968

By J. L. Tokich, A. R. Troiano

Since 1921, when Hull1 discovered that cobalt can exist in the face-centered cubic and hexagonal close-packed modifications, the transitions that occur in cobalt have been extensively studied. It is generally agreed that on heating the hexagonal lattice changes to the cubic structure at ternperatures ranging from 400° to 500°C although considerable doubt exists as to the exact temperature. Data concerning the temperature of the transformation on cooling are much less concordant and their interpretation has not been satisfactory. The study is further complicated by the fact that many investigators have reported the existence of a high temperature allo-tropic change in the range 850 to 1020°C, at which the cubic lattice reverts to the hexagonal modification. The transition on cooling, which has been reported as Occurring at various temperatures from approximately 400 to 100°C, is of particular interest. Troiano and Greninger2 have recently suggested and considered the possibility Of allotropic transformations occurring in pure metals by a shear-type, diffusionless (martensite) transformation. The case of cobalt was specifically discussed and certain observations of previous investigators evaluated in terms Of this type of Of Table 1 briefly outlines the methods and results Of previous investigators Of the transformation temperatures of cobalt. Materials and Methods The major portion of this investigatioll was performed with cobalt sheet containing a total of 0.2 pet impurities with carbon present to the extent of o,I pct. After melting in an induction furnace under an atmosphere of hydrogen, the carbon con. tent analyzed 0.03 pct. Some observations were repeated with hydrogen reduced cobalt compresses analyzing 99.9 pet pure. No significant variations in results were observed employing the as-received sheet, the remelted stock, or the cobalt compresses. Filings for X ray diffraction analysis were sealed in evacuated glass ampoules. Pyrex glass tubing was used for temperatures below (600°C and for higher temperatures clear fused quartz was satisfactory. After appropriate heat treatment at various ternperatures, the specimen ampoules were furnace cooled, air cooled or quenched by crushing under distilled water. This allowed a range of cooling velocities from less than one degree C per set to greater than 1,0oo°C per sec. X ray diffraction patterns were taken with a Debye camera and filtered characteristic cobalt K-alpha radiation. The of of the existing phases was roughly approximated by visual examina-

Jan 1, 1949

By C. E. Shoenfelt

Wildcat drilling in the Rocky Mountain region did not suffer as large a decline in 1942 as was anticipated. The drilling program laid out by the Government at the beginning of the year stressed wild-catting operations and called for reduction of drilling in proved fields. The increased wildcatting campaign did not yield a great many new discoveries, nor important extensions to old fields. Several interesting wildcat wells were drilled in Colorado in 1942 but no new fields were discovered. The Wilson Creek field was extended and about 400 acres added to its reserves. In Montana two new oil fields and two small gas fields were discovered. The developments in the marketing situation had improved, however, making the prospects especially bright for 1943, as will be shown presently in the section on Montana in this report. In New Mexico eight wells were completed, which constituted discoveries ol either oil or gas but none of these was of major proportions. In Wyoming one new oil field and one new gas field were discovered, and one old oil field and one old gas field were extended. Most important was the disco-very of prolific oil producers in deeper sands in three old oil fields, of which one at least, Elk Basin, probably is of major proportions. Government Action On Dec. 26, 1942, President Roosevelt signed the O&apos;Mahoney bill, calling for a flat 12.5 per cent royalty on lands in the public domain. It is expected that the enactment of this bill will encourage wildcatting in the public land states. Opportunity for a full discussion of the problems of reserves and production was afforded at the hearings conducted on the O&apos;Mahoney bill by the minerals subcommittee of the Senate Committee on Public Lands and the statements submitted at these hearings last fall placed the situation, its causes and the logical remedy, clearly on record. It was established at the hearings that for several years the volume of oil discovered per wildcat well drilled has steadily declined; new fields discovered have not been of major proportions; drilling costs have advanced rapidly; a sharp decline in exploratory drilling took place in 1942, while the proportion of dry holes increased; the inescapable conclusion is that to find new reserves the search for oil must be intensified and much more wildcat drilling &apos; must be done. To ensure an adequate drilling campaign, the Petroleum Industry War Council, the Interstate Compact Commission and other representative oil organizations have voiced by resolution their opinion that an upward revision of crude prices is necessary to provide an incentive to the prospector to undertake the hazards of wildcat drilling, since statistics prove that only ope in five or six wells drilled results in actual production. Former Price Administrator Henderson rejected the recommendations for price increases and declared himself unalterably opposed to a general price advance, On the ground that such advances would contribute to inflation. Now that Mr. Hender-

Jan 1, 1943

By C. E. Shoenfelt

Wildcat drilling in the Rocky Mountain region did not suffer as large a decline in 1942 as was anticipated. The drilling program laid out by the Government at the beginning of the year stressed wild-catting operations and called for reduction of drilling in proved fields. The increased wildcatting campaign did not yield a great many new discoveries, nor important extensions to old fields. Several interesting wildcat wells were drilled in Colorado in 1942 but no new fields were discovered. The Wilson Creek field was extended and about 400 acres added to its reserves. In Montana two new oil fields and two small gas fields were discovered. The developments in the marketing situation had improved, however, making the prospects especially bright for 1943, as will be shown presently in the section on Montana in this report. In New Mexico eight wells were completed, which constituted discoveries ol either oil or gas but none of these was of major proportions. In Wyoming one new oil field and one new gas field were discovered, and one old oil field and one old gas field were extended. Most important was the disco-very of prolific oil producers in deeper sands in three old oil fields, of which one at least, Elk Basin, probably is of major proportions. Government Action On Dec. 26, 1942, President Roosevelt signed the O&apos;Mahoney bill, calling for a flat 12.5 per cent royalty on lands in the public domain. It is expected that the enactment of this bill will encourage wildcatting in the public land states. Opportunity for a full discussion of the problems of reserves and production was afforded at the hearings conducted on the O&apos;Mahoney bill by the minerals subcommittee of the Senate Committee on Public Lands and the statements submitted at these hearings last fall placed the situation, its causes and the logical remedy, clearly on record. It was established at the hearings that for several years the volume of oil discovered per wildcat well drilled has steadily declined; new fields discovered have not been of major proportions; drilling costs have advanced rapidly; a sharp decline in exploratory drilling took place in 1942, while the proportion of dry holes increased; the inescapable conclusion is that to find new reserves the search for oil must be intensified and much more wildcat drilling &apos; must be done. To ensure an adequate drilling campaign, the Petroleum Industry War Council, the Interstate Compact Commission and other representative oil organizations have voiced by resolution their opinion that an upward revision of crude prices is necessary to provide an incentive to the prospector to undertake the hazards of wildcat drilling, since statistics prove that only ope in five or six wells drilled results in actual production. Former Price Administrator Henderson rejected the recommendations for price increases and declared himself unalterably opposed to a general price advance, On the ground that such advances would contribute to inflation. Now that Mr. Hender-

Jan 1, 1943

By Charles H. White

METHODS in colorimetry are based on the assumption that the intensity of the color of a definite volume of solution is directly proportional to the quantity of the color-producing substance&apos; present. In the preparation and examination of colored solutions there are three ways in which the depth of color may be varied. These variables are; (1) the quantity of the coloring matter, (2) the quantity of the solvent, or the dilution, and (3) the thickness or depth of that portion of the solution examined. With these three variables as a basis, three general methods in colorimetry have been devised, all of which have been used in the determination of carbon in steel. In the first method, the quantity of the solution is kept the same for both the unknown steel and the standard, and the sections compared are of equal thickness, while the quantity of the standard is varied until the color obtained is of the same intensity as that produced by a definite quantity of the unknown steel. In laboratories where this method is used there is pre¬pared and kept for permanent use a series of solutions with varying amounts of the standard, representing the percentages of carbon from the lowest to the highest demanded in that laboratory. These standard solutions are kept in bottles, or test-tubes of equal diameter, and are arranged in series from the faintest to the most intense color, so that it is a simple matter to find the place of the unknown steel in the series, when the solution is of a definite volume and is contained in a tube of the same diameter as the standard tubes. In the second method, equal quantities of the standard and of the unknown steel are dissolved, the standard is diluted to a definite volume, and the solution of the unknown steel is di-

Sep 1, 1906

By Robert M. Grogan

Fluorspar is the commercial name for fluorite, which is the mineral having the composition CaF2, calcium fluoride. Its valuable properties are due to its content of fluorine, and it is the only important commercial source of that element. The name is derived from the Latin fluere, to flow, because the mineral melts easily and is a good flux. History The mineral has been known since Greek and Roman times, when it was used for drinking cups and ornamental slabs. Various peoples including the Chinese and the American Indians have carved ornaments from large crystals. Its usefulness as a flux was known to Agricola, who wrote about it in 1546.1 Mining began in England about 1775 15 and at various places in the United States during the period 1820 to 1840.28 Substantial production was achieved first in the period 1888 to 1900 in consequence of the development and widespread adoption of the basic open hearth method of making steel, in which fluorspar is used as a flux. After that, production and usage was stimulated by growth in the steel, aluminum, chemical, and ceramic industries and accelerated by World Wars I and II. The organic fluorides called "Freons" entered the picture in 1931, and the use of anhydrous HF as a catalyst in the manufacture of alkylate for high octane fuel blends began in 1942. The development of the froth flotation process in the late 1920&apos;s, a differential flotation scheme for separating fluorspar from galena, sphalerite, and other minerals in the 1930&apos;s, and the application of heavy-media concentrating methods to the treatment of low-grade ores in the 1940&apos;s were outstanding technological contributions that enabled increased production of fluorspar concentrates. Composition and Properties Fluorite in its purest form contains 51.1 pct calcium and 48.9 pct fluorine. Substitution of small percentages of cerium and yttrium for calcium have been noted.4 Mechanical inclusions of gases and fluids such as petroleum and water, and of other solid minerals such as pyrite, marcasite, and chalcopyrite are common. The fluorspar of commerce contains attached and admixed mineral impurities, chiefly calcite, quartz, barite, celestite, and various sulfides. It is interesting that the purest commercial form in which the mineral is sold, acid grade concentrate, contains a minimum of 97 pct CaF2, and as such is of comparable purity to many reagents used in chemical laboratories. Fluorite has a marked tendency to occur in large, well-formed crystals sometimes six to ten inches on a side. It crystallizes in the isometric system, frequently forming cubic and octahedral crystals or combinations thereof. The mineral also occurs in massive and in earthy forms, and in crusts or globular aggregates with radial fibrous texture. Crystalline fluorspar exhibits a great array of colors, from colorless and water clear to yellow, blue, purple, green, rose, red, bluish and purplish black, and brown. The colors are often arranged in alternating bands parallel to cube faces. They may be altered by exposure to X-rays, heat, ultraviolet light, and pressure, and are caused by a variety of factors including the presence of trace impurities and displaced ions in the lattice. Sometimes the changes induced by X-rays can be reversed by ultraviolet radiation. The mineral has a hardness of 4, and is the model of that hardness on the Mobs scale.

Jan 1, 1960

By Laurence Pellier

Electron microscopical studies were made of the effect of sensitization at 1200oF on a Type-.104 stainless steel with high carbon and low nitrogen and oxygen contents, after solution annealing and after cold working. The loci of the carbide precipitates in the early stages of sensitization were followed in dry stripped plastic replicas. Some observations were made by direct electron transmission on thinned films. Intragranular dislocations showed a high degree of stability through the annealing necessary to produce sensitization. I HE present work was undertaken to determine the effect of sensitization, at 1200°F, for 1/2 hr, on the electron microstructure of a Type-304 stainless steel with high carbon, and low nitrogen and oxygen contents, after solution annealing and after cold working. Many electron microscopical studies of sensitization of 18-8 stainless steels have already been made. Most of them utilized extraction replicas, from which the morphology and composition of the precipitated carbides could be established.&apos;-" ry stripped replicas were seldom used for such studies, although it was demonstrated that they are applicable, in general, to EurveYs of the general microstructure of many alloys&apos; and, in particular, to the observation of precipitated carbides in austenitic stainless steels.3

Jan 1, 1963

THE decades immediately before and after the end of the nineteenth century (1890-1910) were a period of increased activity in mineral industry education. One reason for this, undoubtedly, was the rapid increase in mineral production in the decade 1880-1890; pig iron and copper production tripled; coal, lead, and zinc output more than doubled. Most of the other mineral substances followed the same general trend. Aluminum production began in 1886; petroleum output, which in 1888 was less than it was in 1882, almost doubled in the next three years. Gold alone showed no appreciable change until its discovery at Cripple Creek in 1891, followed by the Klondike in 1896, brought to boiling a public interest in minerals that had been simmering for some years previously. The first cyanide plant in the United States was erected at Bodie in 1892, and the first chlorination plant at Cripple Creek* the next year. Silver- lead smelting had already greatly developed, and the metallurgy of copper was almost transformed. The hearth area and smelting capacity of copper reverberatory furnaces more than quadrupled between 1878 and 1894; matte converters were first erected at Butte in 1884. Copper production of the United States in 1899 was 20 times that of 1872. While it was the increased technology used in mineral production that really made the field attractive for educated young men, undoubtedly they did not realize that, and were impressed mainly by the quantitative increase in output. Another factor was the increased general interest in engineering education; three times as many men took engineering degrees in the United States in 1890 as in 1880; 1892 showed almost a 56 per cent increase over 1890. Industry had come to recognize that technical training was worth while. The mineral industry lagged somewhat at first; the total number of mining degrees

Jan 1, 1941