Search Documents

By R. I. Jaffee, E. S. Bartlett, D. N. Williams

The oxidation resistance and fabricability of molybdenum powder-metallurgy alloys containing up to 20 wt pct nickel in the form of a fine dispersion were studied. The effects of dispersion distribution and of amount and type (pure nickel or nickel compounds) of additive were considered. A definite improvement in oxidation resistance was observed, but the amount of improvement fell far short of requirements for an oxidation-resistant alloy. Fabricability by hot-rolling was limited. INVESTIGATIONS at Ohio State university1 and Battelle Memorial institute2 have indicated that the attainment of a truly oxidation-resistant molybdenum-base alloy for high-temperature service, with the coincident retention of high-temperature strength and toughness, will be a difficult, if not impossible, feat. Among the most promising alloy systems studied was the molybdenum-nickel system shown in Fig. 1. Alloys in this system show good oxidation resistance at temperatures well above the normal melting point of molybdenum trioxide because of the regenerative formation of protective nickel-molyb-date (NiMoO4) on the surface of the alloy during exposure at high temperatures. Unfortunately, the required alloy content to obtain oxidation resistant molybdenum-nickel alloys far exceeds the limits of the narrow terminal solid-solution boundary, and closely approaches the peri-tectic composition involving the brittle intermetal-lic compound, MoNi. Because of the peritectic reaction, fusion alloys are characteristically brittle, since the MoNi phase, being the last to form, tends to occur as a continuous grain-boundary network around each molybdenum grain. An added problem with this system is that the protective nickel-molybdate layer formed at high temperatures is unstable, undergoing one or more allotropic modifications upon cooling. The volume changes associated with this modification during cooling are such as to cause violent expulsion of the protective molybdate coating from the surface of the piece. This is, of course, quite detrimental in material exposed to cyclic temperature during service. The research reported here resulted from an attempt to overcome the aforementioned problems associated with the molybdenum-nickel alloys primarily by controlling the amount, size, and location of the MoNi phase. By using powder-metallurgy techniques of alloy preparation and sintering the blended molybdenum-nickel powder mixtures at a temperature below the peritectic reaction temperature, molybdenum-nickel alloys with a randomly dispersed MoNi phase were produced. MATERIALS The molybdenum powder used in the preparation of alloys for this study was commercial hydrogen reduced, minus 325-mesh (Tyler) material. Master alloys, by which nickel was added, consisted of elemental carbonyl nickel powder (12 average particle size), an alloy of 50 wt pct Ni-50 wt pct Cr, and compounds of MoNi, Ni,Si, and Ni2B. The nickel-chromium powder was prepared by filing a vacuum-arc-melted ingot, separating impurities magnetically, and screening to minus 200-mesh. The MoNi powder was prepared by pulverizing a hydrogen-sintered powder-metallurgy compact to minus 325-mesh material. Further sizing of this powder for study of effects of dispersion distribution was accomplished by air classification of the minus 325-mesh powder. The Ni2Si and Ni2B powders were prepared by crushing vacuum-sintered powder-metallurgy compacts to minus 200-mesh material. EXPERIMENTAL PROCEDURE Specimen Preparation—The general procedure followed in the preparation of alloys for testing is described as follows: 1) Blending. Either hand-blending of the powders in a ceramic mortar and pestle for X 1/2 or mechanical blending was used. Hand-blending seemed preferable for optimum homogeneity. 2) Compacting. Most of the blended powders were pressed to green compacts at pressures of 15 tons per sq in. in a single-action die, although some were pressed at 80 tons per sq in. A 1 X 11/4 X 1/4-in. green compact was the standard size for oxidation test material, and 7 X 1/2 X 1/4-in. compacts were used for fabricability test specimens. 3) Sintering. All green compacts were sinteredat

Jan 1, 1959

By J. A. Elias, A. J. Heckler

A simplified method is described for the prepauatior~ of comnposite samples for determination of one quadrant of an X-ray pole figure of a sheet material by the Schulz reflection method. Other special conzposite sampling methods were used to investigate specific areas of the pole figures. Plotting nets for these sampling plans were drawn by a computer. Step-scanning techniques were used to obtain detailed information about specific regions of a pole figure. Satisfactory pole figures were obtained for large-grained (0.5 to 1 in. diam) sheet materials. COMPOSITE sampling techniques for preparing one quadrant of an X-ray pole figure have been reported by a number of authors.'-5 All of these methods are similar in that they use a composite sample prepared by stacking and holding together coupons cut from a sheet material. The schulze reflection technique is applicable to the composite sample so that only minor corrections are needed for defocusing and absorption effects. Also, a relatively large area of a sheet is sampled through the use of multiple cross sectional pieces. In general, sampling methods necessary to obtain a composite-type specimen have been formidable enough to discourage their use in routine pole figure determinations. This paper presents a versatile sampling technique which is simpler than those previously described along with an accurate method for obtaining stereographic plotting nets for any orientation of a composite specimen surface. A step-scanning technique is used to obtain more quantitative determinations of specific regions in pole figures, and the composite technique is satisfactorily applied to determine pole figures of very large grained sheet materials. REVIEW OF PREVIOUS TECHNIQUES Mueller and ~nott' first proposed a technique for obtaining one complete quadrant of an X-ray pole figure by using a sheet sample and six different composite samples in which the individual coupons were aligned and held together by two types of jigs. Data from the seven different samples were overlapped to obtain a single quadrant. ~eieran~ and Lopata and ~ula~ obtained a complete quadrant of a pole figure from a single sample prepared by forming a cube from coupons cut from a sheet. These coupons were bonded together using an epoxy cement, and a cut was made at 54.7 deg to the normal, transverse, and rolling directions of the sheet, Fig. I. The normal direction of the cut face projects into one quadrant of a stereographic projection at equal angles to the three principal orthogonal reference directions mentioned above. X-ray reflection data obtained along a spiral path in physical space could then be plotted on a stereographic net offset 54.7 deg from the normal, as shown in Fig. 2. A rotation about an axis representing the surface normal is designated as a, and a rotation about an axis lying in the plane of the surface is 4. From Fig. 2 it is apparent that a tilting angle of no more than 55 deg @ is necessary to obtain the complete quadrant. ~eber~ devised an improved sampling technique by cutting coupons 45 deg to the rolling direction of a sheet, stacking and bonding these with an epoxy cement at an angle of 54.7 deg to a reference plane, and finally grinding and lapping a flat specimen surface parallel to this plane. An important consideration of this technique and that of Lopata and ~ula~ is variation in the diffracting power of the specimen surface due to the bonding medium. While any composite-type sample will have some such variation due to boundaries between coupons, the problem can be minimized by elimination of the bonding medium and by avoiding prolonged etching times which could lead to significant inter lame llar attack of the coupon faces. EXPERIMENTAL TECHNIQUE We were working concurrently though independently on a technique similar to ~eber's,' but which does not

Jan 1, 1968

By L. S. Birks

The bainite transformation in a 3.5 pct Ni-1.25 pct Cr steel was studied under various conditions of cooling and stress. Several characteristics may be specified: 1) transformation in the bainite region (925° to 575°F) is very little affected by the manner of cooling from the austenitizing temperature at 1600°F to 575°F)tothe upper limit of bainite transformation at 925°F; 2) starting time for the bainite transformation is the same order of magnitude for either isothermal transformation or continuous cooling, but the rate of transformation is somewhat greater for isothermal transformation; 3) tensile stress accelerates both isothermal and continuous cooling transformation, and 32,000 psi stress changes the form of the isothermal transformation diagram to correspond in appearance to the continuous cooling diagram; 4) transformation for nonlinear, continuous cooling may not be determined directly from the linear, continuous cooling transformation diagram, but may be predicted by assuming first that the fractional amount of austenite transformed in a given small temperature interval depends on the approximate linear cooling rate during that temperature interval and then by summing stepwise over the whole temperature range. IN a previous publication' an X-ray spectrometer was described with which the X-ray diffraction from a specimen could be observed continuously under controlled temperature and tensile stress. This instrument has now been applied to a study of the austenite-bainite transformation in a Ni-Cr steel for both isothermal and continuous cooling conditions, with and without stress. Certain characteristics of the transformation lead to a method of predicting the amount of transformation to be expected at a given temperature for any type of cooling curve. Material and Specimen Preparation The steel chosen for the investigation was a Ni-Cr steel having the composition in the following percentages: 0.30 C, 0.27 Mn, 0.019 P and S, 3.50 Ni, and 1.25 Cr. In order to fabricate specimens suitable for the X-ray spectrometer, a 1/4 in. plate was ground down to 0.060 in. and then cold rolled to about 0.035 in. Next it was heat treated by quenching in oil from 1650°F and tempering at 1200°F for 1 hr. Then it was etched in dilute nitric acid to reduce its thickness to 0.014 in. and cut into blanks in the shape of flat tensile specimens 3 1/4 Vi in. long, 7/16 in. wide, with a notch % in. long and 7/32 in. wide; see Fig. 1. X-Ray Technique Since the X-ray spectrometer has been described in detail elsewhere,' only a brief outline of the principles will be repeated here. A focusing, pow- der-diffraction arrangement' was used, as shown schematically in Fig. 1, and the specimen was mounted vertically in a vacuum furnace (not shown in the figure). The X-rays, moving in a horizontal plane, enter and leave the furnace through beryllium windows. As shown in the figure, X-rays diverging from the line source A are diffracted by the specimen B and converge at the detector slit C. The detector D and the slit C may be set at the proper angle in the horizontal plane to receive X-rays diffracted by either the face-centered phase (austenite) or the body-centered form (ferrite, bainite, martensite). The specimen is heated by electrical conduction between connectors E, and E,, and a Pt—Pt-10 pct Rh thermocouple spot-welded to the center of the notched region on the side away from the X-ray beam indicates the temperature continuously on a Brown recorder. Temperature control is exercised manually with a variable transformer on the input to E,-E,. Any desired time-temperature relationship is easily obtained by first drawing the desired curve on the temperature recorder chart and then adjusting the variable transformer during the run so that the thermocouple

Jan 1, 1957

By I. M. Bernstein

The steady-state creep behaviov of zirconium and zivcaloy-2 was examined in the temperature vatlge 520° to 620°C A1 low stresses the creep rates were cimracterized by a linear stress dependence; at highev stresses the stress dependence was much more pronounced. Temnperature-cycling tests yielded values for the aclivation enevgy for creep. Various tlzeories were examined in the ligltt of- the experimental re-sults and it mas concluded that the low-stress creep behavior is the result of the stress-direcled diffusion of vacancies along gain boundaries. It has been observed,"&apos; usually under conditions of high temperature and low stress, that creep deformation can occur for which the steady-state creep rate is linearly dependent on the applied stress. For magnesium and certain magnesium alloys, Harris and ones&apos; and ones&apos; have argued that this type of creep occurs by mass transfer as a result of the stress-induced generation and migration of vacancies, along a gradient defined by the stress direction. Jones&apos; demonstrated that the rate-controlling diffusion path is sensitive to grain size and temperature, and that by suitable control of these variables creep could occur by vacancy diffusion either predominately along grain boundaries or through the lattice. Recently, Jones3 suggested from an examination of limited high-stress data for zircaloy-2, composition in Table I, that significant diffusion creep could occur at low stresses, at least between 375" and 500°C, controlled by grain boundary vacancy diffusion. This process could have an important implication in assessing the role of zirconium alloys as a structural or cladding material in certain classes of nuclear reactors, since it predicts creep deformation far in excess of any estimates based on extrapolating slip creep data from higher stress levels. If the diffusion creep process occurs it should be possible to describe the total steady-state creep rate of zirconium and its alloys as the sum of two terms, Eq. [I]; the first term relates to a slip creep process important at high stresses and which is manifested by a much more pronounced dependence of creep rate on stress4 than diffusion creep and the second to a process controlled by mass transfer,5&apos;6 dominant at low stresses: where A and BI are parameters which can depend on structure, Ql and Q2 are the activation energies for the particular creep process occurring, and n describes the sensitivity of the creep rate on stress. It is the purpose of this paper to present some direct experimental evidence in support of this view. It is recognized that other analytical approaches have been proposed to explain data of this kind and these will also be discussed. 1) EXPERIMENTAL PROCEDURE Flat creep specimens (gage length 1 by 0.25 by 0.02 in. approx) were prepared from cold-rolled, argon-remelted, crystal bar zirconium and cold-rolled commercial-grade zircaloy-2, the analyses of which are given in Table I. The specimens were annealed at a pressure of < 10-5 Torr at temperatures from 625" to 675°C for 2 hr and slow-cooled. This treatment produced stable grains of average size (defined here by the average linear intercept) of for zirconium and -4xin. (-10 p) for zircaloy-2. The specimens were tested in a dead load tensile creep rig. The stress was maintained constant by adjusting the applied load after approximately each 1 pct of strain. The specimen temperature was controlled to better than +1°C. This system had a small thermal lag, so that rapid temperature changes were possible. To minimize corrosion, the specimens were tested in high-purity (99.95 pct) argon, further dried,

Jan 1, 1968

By W. R. Kanne, P. R. Strutt, R. A. Dodd

A study has been made of the creep behavior of ß-NiAl of stoichiometric composition in the temperature range 475" to 775°C. Single crystal tensile specimens were deformed under a constant applied load. From slip line studies and tensile axis rotations it was concluded that the crystals deformed by pencil-glide on (100) and (110) planes with a (100) slip direction. Electron microscope thin-film studies showed evidence for profuse cross-slip, and the dislocation Burgers vector was determined to be (100). There was no tendency for the dislocations to lie in definite slip planes, although a strong alignment of segments of edge dislocations was frequently seen. The activation energy for creep in the temperature range 475" and 775°C was judged to be much lower than that for creep at temperatures above 775°C. It is possible that the rate-controlling process is the thermally activated cross-slip of screw dislocations. In recent years considerable interest has developed in the possible use of high-melting-point intermediate phases for high-temperature applications necessitating good creep resistance. Ordered alloys such as Ni3A1, modified by alloying additions, have received particular attention, culminating in the recent development by Pratt and Whitney of single crystal turbine blades.&apos; The intermediate phase NiAl has considerable theoretical interest from a creep standpoint because not only is it ordered up to the melting point (-1650°C at stoichiometry) but it contains a high concentration of structural vacancies on the aluminum-rich side of stoichiometry. These vacancies are known to exert a strengthening effect under some conditions,&apos; but in addition they might be expected to affect high-temperature creep rates through dislocation climb. The present paper deals with the slip line and dislocation structures developed during creep of stoichiometric NiAl between 475" and 775C, and with possible attendant creep mechanisms. MATERIALS AND TEST TECHNIQUES NiAl ingots of stoichiometric composition were prepared by induction melting 99.996 pct A1 and 99.98 pct Ni (kindly provided by the Kaiser Aluminum Co. and the International Nickel Co., respectively) in 100 cc pure alumina crucibles in a helium atmosphere. No chemical melting flux was used in order to avoid con- tamination of the alloy. Each ingot was slowly direc-tionally solidified to avoid porosity and to produce very large grains up to 2 in. in length. In this way, ingots were obtained which were suitable for sectioning into single crystal creep specimens. Chemical analysis indicated that all alloys were within the range 49.6 0.3 at. pct Ni. For the present investigation, identical rectangular single crystal blanks were cut vertically from one particularly large crystal in an ingot using a series of three diamond cut-off wheels with appropriate spacers. Thus, all sliced crystals had the same orientation with the tensile axis parallel to the long side of the rectangle; the initial orientation of the tensile axis is shown as S, in Fig. 1. The blanks were homogenized at 1250 to 1300°C for 48 hr and subsequently cooled slowly to room temperature. A gage length of rectangular cross section and about 0.75 in. in length was prepared on each specimen using an electrolytic lathe and a dilute nitric/phosphoric acid electrolyte. The gage length cross section was 0.250 0.0005 in. by 0.040 ± 0.0005 in. Holes to accommodate tensile grips were electrolytically machined using a rotating acid jet. After creep testing, this same technique was used to cut discs for transmission electron microscopy. Thus, all shaping was done electrolytically, the only exception being that (122) sections were spark-machined from some speci-

Jan 1, 1970

By V. J. Kniazeff, S. A. Naville

The problem of unsteady-state condensate-gas flow through porous media leads to a set of second-order non-linear partial differential equations. Such a set of equations is numerically solved in the case of radial two-phase flow around a well, taking into consideration both the thermodynamical properties of the fluid and the mechanical properties of the reservoir. The fluid properties, reflecting the PVT relationship of the gaseous and liquid phases, are expressed by using the partial specific masses of the two main separator products in these phases. The flow properties of the reservoir rock are expressed by the generalized Darcy&apos;s law for the liquid phase and by a quadratic relationship between the rate of flow and the pressure gradient for the gaseous phase. The numerical solution of the equations for pressure and saturation US radius and time is worked out through programs written for a computer. The evolution of bottom-hole pressures, well productivities or- deliverabilities and effluent compositions with the depletion of the reservoir is easily derived. The application to the Saharian gas-condensate field Hassi R&apos;Mel led to a better understanding of the drainage mechanism. A zone of fairly high liquid saturation develops around the wells, reducing the effective permeability, and represents a loss of condensible products in addition to the PVT-like retrograde condensation. lnside this zone, near the well, the deviation from Darcy&apos;s law for the flow of the gaseous phase governs the well deliver-ability. A back-pressure test has been computed and correlates with the field results. INTRODUCTION Two-phase flow of volatile hydrocarbons, like condensate gas or light crude oil, may be treated as the flow of a binary mixture by an arbitrary division of the chemical components into two groups. This is translated into two equations of mass continuity, which constitute a set of relation- ships for the pressure and the saturations vs the space coordinates and the time. The equations contain the laws governing the composition and the motion of the phases. The problem so defined is solved with the assumption that the compositions of the phases at any pressure are respectively the same as those observed in a PVT measuring cell under differential liberation. In a first series of computations, it was assumed that the flow obeys the generalized Darcy&apos;s law. A satisfactory representation of the retrograde condensation around the well was thus obtained. In addition, the trend toward decreasing effective permeabilities was obtained, and the computed composition of the effluent checked the laboratory values. However, it has not been possible within this basic assumption to represent the non-linear relationship between the production rate and the bottom-hole pressure drawdown as observed for gas wells in the field. Following the advice of A. Houpeurt it was decided to consider the relative permeability to gas as a function of the velocity of the gas Phase.1 The necessary physical determinations were made by E. COstaséque using a method devised by A. Houpeurt and R. Iffly. As numerical processing of the equations progressed, several difficulties were encountered which were overcome through collaboration with the computer manufacturer. This mathematical model of two-phase flow in porous media had been primarily intended for and extensively applied to the case of the Hassi R&apos;Mel gas-condensate field, operated by SN Repal for SEHR, a joint subsidiary of SN Repal and CFP (A). The programs have also found their applications to forecast the behavior of several fields in the Sahara area containing light and volatile hydrocarbons. BASIC EQUATIONS We will consider a zone in the porous reservoir where the flow properties and the in situ composition of the fluids can be assumed to be uniform. A part of the equations of transient flow can be written with the specific gravity of the fluids being taken equal to the sum of the contributions due to the

Jan 1, 1966

By R. O. Williams

Measurements have been made of the internal energy of deformation in a Cu-A1 alloy and a Cu-Zn alloy as the deference between the work and the released heat. The method required the rapid compression of samples to reduce thermal interactions. The rate of energy storage is low initially but then becomes almost linear with strain. Both alloys stored about 60 cal per mole at a strain of 0.4 in the recrystallized condition. The fractional rate of storage increases at low strains reaching about 0.25 at a strain of 0.15 and then decreases slowly with increasing strains. As do pure metals, these alloys release appreciable energy immediately following deformation; in contrast with pure metals, however, the release continued for extended periods of time. This energy release is somewhat sensitive to the amount of deformation, the deformation temperature, and prior thermal & eatment. It is believed that this release is a composite of that observed in pure metals which has been attributed to dislocations and that due to the motion of vacancies which produces increased short-range order. IT is expected that changes brought about by deformation of a pure metal can be understood in terms of the three defects—dislocations, vacancies, and interstitials—along with the interactions possible between these defects. Frequently stacking faults are created and must also be considered. 1t is not immediately clear whether or not the stress fields which are created should be regarded as independent of dislocations. For alloys there is the important additional effect of atomic configuration, for example short-range order, which must also be considered and will, in general, interact with each of the above defects. While it is true that a complete understanding of pure metals is not yet possible, it would seem very valuable to establish the similarities and differences between pure metals and alloys. Such knowledge could contribute to the understanding of both. A study of the changes in internal energy resulting from deformation of two alloys is reported here. Although some information has been available for alloys almost as long as for pure metals, the volume of work has been substantially less. Sato&apos; and Quinney and Taylor&apos; were responsible for the earlier work, both using brass and annealing calorimetry. tizhnova&apos; studied stored energy in Cu-Ni alloys by a method somewhat similar to the one reported here. Bever and his co-workers have made extensive studies of Au-Ag alloys4&apos;5 and more recently CU-AU&apos;U&apos; using solution calorimetry. Clarebrough et a1.&apos; have recently studied brass using annealing calorimetry. EXPERIMENTAL METHOD The present results were obtained by the rapid, adiabatic compression of a sample about 1/4 in, diam by 1/2 in. long between two tungsten carbide hammers. A vacuum provided thermal isolation and oil provided effective lubrication between the sample and hammers. The increase in internal energy is the difference between the mechanical energy and the heat liberated within the sample. The mechanical energy was determined from the velocity of the hammers (calculated from the height through which the hammers traveled) and was essentially constant for each deformation cycle. The heat was determined from the temperature increase of the sample which was measured by an embedded thermocouple. Specific heat data were calculated from Neumann&apos;s rule using tabulated data for pure metals.9 Since the fraction of the energy which is stored is large compared to that for pure metals, specific heat data of high accuracy are not required. Successive increments of deformation were carried out by repeating the procedure, the limit being determined mostly by the decreasing accuracy caused by the increasing corrections and the decreasing storage of energy. About five cycles were used to give a true strain of about 0.5 while the time interval between cycles was 1 to 2hr.

Jan 1, 1963

By E. P. Klier, Jane Jellison

The course of the transformations on cooling in a series of Cu-A1 alloys has been followed by means of thermal analysis, X-ray diffraction, and optical metallogrAphy. Specimen size was found to have a pronounced effect on the time of completion of the pearlite transformation due to modification in the unmber of nuclei. The ordeving transformation zvas observed for all cooling rates for all alloys studied, and is considered insuppvessible. At intermediate cooling&apos; rates, a transitional struchire for 011 alloy compositions and based ox the bainite reaction was observed. The alloys of aluminum and copper possess a eu-tectoidal region at from about 9.4 to 16 pct Al. Above the critical temperature, the disordered bcc phase, 0, is stable. At subcritical temperatures, the 0 phase decomposes under equilibrium conditions into the stable phases, a and y,. At the eutectoid composition, these phases develop a lamellar pearlite structure, in appearance much like that found in steels. During rapid quenching from supercritical temperatures, the diffusion processes required for the formation of the equilibrium phases are suppressed, and the 0 transforms to an acicular martensitic phase, designated B or y&apos; depending on the aluminum content, or to a mixture of the two. Early investigators of this system concentrated on determining the equilibrium phase diagram, &apos;&apos;&apos; the structure of the equilibrium phases,3 and later the isothermal decomposition of the 0 phase at subcritical temperatures, or the decomposition of the martensite on tempering. Other work which treated the nonequilibrium transformations concentrated largely on the martensite transformations and the structure of the b and y&apos; phases.15"17 Since the pearlite and martensite transformations in this system resemble those in steels, the one being formed by nucleation and growth of adjacent lamellae of the equilibrium phases, and the other by a diffusionless, shear-type transformation, the present study has been undertaken to investigate the structures formed on continuous cooling, with the objective of constructing cooling transformation diagrams analogous to those derived for alloy steel systems. In particular it was desired to determine whether parallels between the A1-Cu and iron-iron carbide systems on continuous cooling extended to encompass the intermediate phase, namely the bainite structures, which form by a combined martensitic-diffusion mechanism,&apos;&apos; but which are supersaturated with respect to the equilibrium phase upon which their crystal structure is based. To this end the transformations in representative alloys of the Cu-A1 B eutectoid system have been followed, using the methods of thermal analysis, X-ray diffraction, and optical microscopy. EXPERIMENTAL PROCEDURE Materials. The materials tested were those used by Klier and Grmko 5 in their study of the isothermal decomposition of these alloys. The alloys were melted in graphite crucibles and chill-cast into 5 by 2 by 1/4 in. ingots. The ingots were then hot-rolled to sheets 1/8, 1/16, and 1/32 in. thick. The compositions are given in Table I. Specimen Preparation. Specimens for thermal analysis were in the form of small squares approximately 1/4 in. on a side. For the 11.9 and 13.5 Al-Cu alloys, the sheet thickness was 1/16 in. and for the 10.5 A1-Cu alloy the 1/32-in. sheet was used. One lead of a chromel-alumel thermocouple was spot-welded to either face of the square with the specimen itself thus forming the hot junction of the thermocouple. Specimens for X-ray analysis were prepared as filings from martensitic sheet stock and were sealed in glass ampoules under 1/2 atm of argon. Metallographic examination of the powder specimens was carried out on a portion of the heat-treated filings mounted in lucite. All specimens were examined metallographic ally after etching

Jan 1, 1965

By W. A. Young

Polynomial functions of temperature were obtained for the specific heats, thermal diffusivities, and thermal conductivities of zirconium hydrides containing 4 at. pct U. Three hydrides (H/Zr atom ratios of 1.58, 1.65, and 1.70) were studied over the range a" to 900°C and a fourth (H/Zr = 1.81) was studied over the range 0° to 760°C. The specific heats were determined from enthalpy measurements which were obtained using a unique drop calorimeter specifically designed for use with materials in which high temperature phase transitions and/or high dissociation pressures occur. Thermal diffusivities were measured by the flash method using a pulsed laser. The thermal conductiuities were obtained as the product of specific heat, thermal diffusivity, and density. The specific heats agree, within 10 pct, with values derived using a theoretical model in which the hydrogen and zirconium atoms are treated as Einstein and Debye oscillators, respectively. RELIABLE values of the thermophysical properties of the fuel are required to predict the operating temperatures and temperature response of SNAP nuclear reactors. Among the most important of these properties are the thermal conductivity, specific heat, and thermal diffusivity. A considerable number of investigations1-4 have been made of these properties for the Zr-H and Zr-H-U systems.* However, little of the drides, however, this direct method cannot yield meaningful results, since the hydrogen will redistribute under the influence of the thermal gradient, thus forming a concentration gradient; hence, one has a spectrum of compositions, rather than a homogenous alloy. Although the "average" composition of the material may be identical to the initial uniform concentration, the directly measured value of conductivity will be dependent on the thickness of the specimen, due to the highly sensitive dependence of transport properties on hydrogen content. This dependence is strikingly illustrated by the work of Bickel,5 who found that the electrical conduction of zirconium hydrides ranges from primarily hole conduction to primarily electronic conduction, depending upon the hydrogen content. Fortunately, the direct measurement of thermal conductivity is unnecessary, since it can be expressed as the product of the specific heat, thermal diffusivity, and density, all of which can be directly measured with considerable accuracy. EXPERIMENTAL Specimen Preparation. The combined fuel-moderator material used in SNAP reactors is a hydrided zirconium-uranium alloy containing -10 wt pct U. The alloy used in this work was representative of that used in nuclear reactors except that normal uranium was substituted for the enriched uranium required for reactor usage. It was produced by a triple-arc-melt and double-extrusion process. All specimens were prepared from a single cylindrical extrusion which contained 10.30 pet U, 89,35 pct Zr, and 0.35 pct impurities, The specimens for each composition were hydrided simultaneously with ultrapure hydrogen (10 ppm total impurities) using standard fuel production techniques which routinely yield homogeneous, crack-free fuel with negligible increases in the impurity levels. The hydrogen content of each specimen was determined from its weight gain and the density was measured by liquid displacement, Chemical analyses yielded hydrogen concentrations which agreed with the weight gain data within ±0.02 in H/Zr atom ratio) the concentrations of all other elements agreed almost exactly with the initial values after adjustment for the added hydrogen. The specimens used for the determination of specific heat were centerless ground to 2.00 cm diam after hydriding. A thin slice was carefully removed From each end for metallographic examination. In every case, this examination revealed a uniform structure as evidenced by the appearance and distribution of the two phases present in the fuel at the hydrogen concentrations used. TWO specimens (H/Zr = 1.600 and 1.632) appeared to be entirely 6 phase with equi-axed grains; the specimen with H/Zr = 1.756 showed

Jan 1, 1970

By E. E. Underwood, L. L. Marsh

Aluminum single crystals, alloyed with 0.042 atomic pet Cu and 0.11 and 1.1 atomic pct Mg, were subjected to constant stress creep tests, tensile tests, and hot hardness measurements within a temperature range of 300° to 866OK. Calculations based on Dorn&apos;s temperature-compensated time parameter, 6, gave a value of DH, = 27,000 cal per mol for the activation energy of early creep in aluminum single crystals. Correlations have been obtained for aluminum alloy single crystals with the parameter E for solid solution strengthening, as well as with the parameter F for solid solution hardening, by using a valence of three for aluminum. Limited measurements on tensile specimens show that the slip band density tends to decrease with increasing temperature and with decreasing solute concentration. INCREASING interest is being shown in the mechanisms of plastic deformation in single crystals during tensile and creep testing. The complexity of deformational processes in polycrystalline materials has led to a search for simpler experimental conditions. Numerous creep and tensile investigations have been conducted with pure, metallic single crystals. To a lesser degree, the effects of alloying elements on the tensile properties of single crystals have been determined. However: the literature dealing with the effects of alloying additions in single crystals under creep conditions is vanishingly small. This paper represents an attempt to narrow this gap in the knowledge of the subject. Previous investigations of creep behavior at the Battelle Memorial Institute1-1 have been of great value in the analysis of the present single crystal data. It is equally desirable, however, to ascertain the extent of correspondence between the behavior of single crystal and polycrystalline materials. For this purpose, correlations, similar to those developed for polycrystalline aluminum alloys by Dorn and co-workers, have been made with the single crystal data. The results from this study have tended to confirm and extend those correlations to the case of alloyed single crystals. Materials and Procedures Three dilute binary aluminum alloys were prepared for this investigation from 99.99 + wt pct Al, 99.8 wt pct Mg, and 99.92 wt pct (electrolytic) Cu. The nominal compositions of the alloys were 0.042 atomic pct Cu, and 0.11 and 1.1 atomic pet Mg. Precautions were taken to avoid contamination of the stock during melting and casting of the alloys. After a heat treatment of 8 hr at 925°F the alloys were extruded, then machined into) threaded tensile specimens with a 3 in. reduced section and a 0.505 in. diam. Spectrographic examination showed less than 47 ppm metallic impurities in each alloy. The single crystals were grown by the strain-anneal method, with a critical strain of about 11/4 pet giving the optimum results. In general, 3 in. crystals were obtained with the Al-Cu alloy, but smaller crystals in the magnesium alloys necessitated the use of 2 in. and 1 in. gage lengths with the low and high magnesium alloy specimens, respectively. After an electrolytic polish, the orientation of that portion of the specimen containing the largest single crystal was determined from Laue back-reflection photographs. Tensile tests were conducted at a constant load rate of about 2 lb per min. Creep runs were made in a constant temperature room, under constant stress at the higher creep temperatures, and constant load at the lower temperatures. The eloneation was measured to within ±5 microin. by a specially designed capacitance extensometer. The ex-tensometer arms were attached to the 3 in. specimens at the shoulders of the test piece or, where the crystals were smaller than 3 in., by knife-edge grips.

Jan 1, 1957

By Gordon H. Geiger, J. Bruce Wagner

Electrical conductavity and therrnoelectvic nzeasuretnents on synthetic hematite slabs with 0.01 to 0.90 at. pet Ti and with 0.30 at. pet Ca were made. Additions of titanium and of calcium both increased the electronic conductivity with titanium yielding greater n-type behavior and calciurn p-type behavior. Reduction studies of hematite to magnetite in CO-CO2 atmospheres between 600° and 900°C initially exhibited linear kinetics. These linear rates were increased by additions of titanium and decreased by calcium. IN recent years many studies have been reported in the literature on the kinetics of the reduction of hematite and magnetite to iron. In addition, Hansen and Josephl and Schenck and Schultz2 have reported studies on the reduction of hematite to magnetite, the first step in total reduction to iron. In order to evaluate the results of the studies of over-all reduction in terms of the actual mechanism of the reaction and to define further the important factors in the rate- controlling mechanism of the magnetic roasting reaction, the following experiments were undertaken. Specimens of undoped hematite and hematite containing titanium or calcium in solution as doping agents were reduced to magnetite in CO-CO2 mixtures. In addition, electrical-conductivity measurements were correlated with the reduction kinetics using concepts of defect solid-state chemistry. EXPERIMENTAL Fisher certified Fe2O3 powder was used to make specimens for both the electrical and kinetic studies (see Table I for analysis). Doping with titanium and calcium was accomplished by adding TiO2 and CaO powders to the Fe2O3 powder. The powders were mixed in a Waring blender for minimum times of 1/2 hr. Satisfactory blending was achieved based on comparison of analyses of individual specimens af- ter reduction. The specimens were formed in a steel die using opposed punches with a rectangular opening 10.0 by 40.0 mm. The Fe2O3-TiO, platelets were pressed cold at 16,000 psi. They were sintered for approximately 16 hr at 1075°C in air, in accordance with information in the literature3, 4 on the time and temperature needed to obtain solution of the titanium in the hematite. The Fe2O3-CaO mixtures were first cold-pressed at 20,000 psi and sintered for 3 hr at 1225°C to insure solution of CaO. This material was then ground to -325 mesh in a 6-in. ball mill and the resulting powder was used to make platelets in the same manner as above. The sintered platelets were usually between 1/16 and 1/8 in. thick. They were ground on a carborundum wheel and polished on 2/0 paper. Typical dimensions of the kinetic-study specimens were 1.6 by 0.8 by 0.05 cm, and a typical weight was 0.3 g. Conductivity and thermoelectric specimens were approximately the same size, but were subjected to further sintering in order to ensure maximum densification. Finally, all specimens were measured to the nearest 0.0005 in. and weighed on a Mettler H-15 balance to the nearest 0.0001 g and the density calculated. The average density of the specimens used for the reduction studies was 4.87 g per cc, or 7.1 pet total porosity. The standard deviation ranged from 0.14 to 0.063 g per cc within a composition group. In the present study, the apparent surface area as measured with a micrometer was taken as the true surface area. The chemical analyses for calcium and for titanium within a group showed maximum variations of 50.04 pet from the average values used in Figs. 9 and 11. In order to suspend the specimen from the balance for the kinetic studies, a hole, 0.03 in. in

Jan 1, 1965

By R. L. Jones, H. Conrad

The effects of gain size on the room-temperature tensile properties of commercial(A- 70)-purity and iodide-purity titanium were investigated by concurrent tensile testing and thin-foil electron transmission studies. The mechanical tests showed that the effect of grain size on the yield, flow, and fracture stresses could be expressed by relations of the Hall-Petch type. The magnitude of the grain size effect on the yield stress was larger for commercial-purity than for high-purity titanium, but in both materials it was intermediate between that typically observed for fcc and for bcc metals. The effect of strain on the gain size sensitivity of the flow stress was found to reflect the grain size dependence of strain hardening. The electron transmission study indicated that the tensile behavior could be accounted for in terms of the dislocation densities and distributions formed during deformation. It was concluded that the effect of grain size on strength could be attributed to a relationship between grain size and the dislocation densities generated in initiating and sustaining plastic flow, the difference in stress levels being due to strain hardening. The relationships between recrystallized grain size, uniaxial tensile properties, and dislocation substructure have not been explored in any detail for a titanium. With titanium and its alloys finding increasing applications in aerospace systems, such information has become essential. The research described in this paper had two objectives: first, to document the effect of grain size on the yield, flow, and fracture stresses of unalloyed a titanium by the tensile testing of recrystalliied specimens at room temperature; second, to attempt an interpretation of the mechanical test behavior in terms of the dislocation structures formed on deformation, as observed by transmission electron microscopy of thin foils prepared from deformed tensile specimens. The observations reported here are restricted to room-temperature deformation; the effect of temperature on the yield and flow stresses of a titanium and the athermal nature of the contribution of grain size to the flow stress have been discussed elsewhere.1"3 EXPERIMENTAL DETAILS Two purity grades of unalloyed titanium have been investigated: Crucible Steel A-70, a typical commer- cial-purity product, and a high-purity iodide grade supplied by the Foote Mineral Co. Chemical analyses for interstitial impurity contents are given in Table I, together with values for the total interstitial atom fractions in terms of oxygen equivalents, which were calculated by the method outlined previously.4 ,5 According to the manufacturer&apos;s nominal analysis, the A-70 grade also contains about 3700 ppm of Fe. The A-70 grade was supplied as 1/4-in.-diam centerless-ground rod. The iodide grade was supplied as crystal bar which was consolidated to approximately 1/4-in.-diam rod by a single, rapid, molten zone pass, using electron beam heating. The 1/4-in. rods were cold-swaged to 0.078-in.-diam wires and 2-in. lengths were recrystallized in a vacuum of -5 x 10-5 torr, giving grain sizes in the range 0.8 to 30 . The thermal treatments and resulting grain sizes are summarized in Table 11. Since there was in no case any obvious sign of a bimodal dis tribution of grain sizes, the grain size values quoted in Table I1 are those obtained from mean linear intercept measurements involving >I00 grains. For the two coarse grain sizes the measurements were made using conventional optical techniques. It was noted during these determinations that the etchants used (10 pct HF; 30 pct HN03; 60 pct H20 and 2 pct HF; 2 pct H202; 96 pct H20 were both tried) etched grain boundaries very nonuniformly and optical polarization effects had to be employed to reveal boundaries which might otherwise have been missed. It was found that this problem became more acute with the finer grain sizes as the usefulness of polarization diminished.

Jan 1, 1970

By H. H. Rachford, J. Douglas, D. W. Peaceman

A numerical solution of equations describing two-phase flow in porous media shows promise in providing a technique for predicting the displacermet from satlds of oil by water or gas. The description includes the influence of relative permeability, fluid viscosities and densities, graviry, and capillary pressure, and, tholrgh tested ortly for two-dimensional cases, should be eqlmlly applicable in three-dimensional geometry. Two memorical methods ore presented: the first method is quite general in its applicability; the second method can be used only with certain types of boundary conditions but requires less computing. Comparisons of computed results with data from Inhoratory models are presented. These data were taken on a water flood of a strarified model and on water floods of a five-spot model for favorable and unfavorable mobility ratios. On the stratified model, excellent agreement with recovery at breakthrough was obtained; agreement with recovery after breakthrough was poor. In the five-spot model, good agreement was obtainecl with recovery at and after breakthrough. The purpose of this paper is twofold: first, to present a reservoir engineering method requiring knowledge only of rock geometry and the normally measured rock and fluid properties for calculating the multi-dimensional flow of water displacing oil from porous, water-wet rock containing connate water; and, second, to investigate the validity of the method by comparing results of calculations with previously observed displacements in laboratory models. The availability of such a verified technique of reservoir analysis would afford major advantages. First, it would demonstrate that the fundamental macroscopic concepts of two-phase fluid mechanics, i.e., relative permeability and capillary pressure, yield an adequate description of the physical process. Also, since most reservoir rocks appear to be water-wet and contain connate water along with oil, it would provide a method of technical and economic value for calculating the course of oil displacement by water directly from measured reservoir and fluid properties. It is important to emphasize that the calculation is subject only to the limitations of detail and precision of reservoir information, but not to limitations introduced by simplifying assumptions. Further, it would providc almost the only means of examining the influence of factors such as the size and extent of reservoir inhomogeneities and uncertainties in the basic reservoir data. Knowledge of this influence is essential in stating quantitatively the detail required to define a reservoir and in establishing the relation between the uncertainty in the definition of reservoir properties and the reliability of predicted performance. Moreover, in the process of solving a particular problem much detailed information would become available about the displacement process. For example, at each point in the reservoir for all stages of the displace ment. the calculations would yield not only the water and oil saturations but also the direction and magnitude of fluid velocities and the local fluid mobilities. Such dctail is potentially of great value in giving insight into the mechanics of particular displacements. The development of such a method has long been the goal of research in the application of numerical an-alysis to petroleum reservoir enginecrinz. The most complete treatment of the displacement process published to date is that of Douglas. Blair, and Wagner,&apos; which, however, was limited to flow in a single dimension. The method presented in the present work is hascd on the numerical solution of a finite difference analogue of the multi-dimensional differential system describing the displacement process. Although current work has considered only displacement of oil by water from water-wet sands, the differential system for other immiscible displacements, such as gas displacing oil with which it is in phase equilibrium, is quite similar. It should therefore be expected that the technique described will be applicable to displacement by gas as well. The description of the simultaneous flow of fluids through porous media in terms of relative perrncability and capillary pressure has been adequately discussed in the literature and standard textbooks. Sec, for exampje, Muskat. Chapter VII.&apos;

By S. V. Krusiewski, J. W. Gabelman

Regional metallogenic zones and areas of equal paragenetic range have been interpreted from a compiled metallogenic map. of Mexico. Mineralization gradients of the pattern subsequently identified extend inland from coastal zones of high-temperature mineralization, and join in a central longitudinal zone of relatively low-temperature mineralization, apparently leaving no zonal room for lowest temperature deposits. The striking regional zoning pattern can be correlated with regional deformation gradients of similar position and orientation. The gradients represent at least three major orogenic cycles in two structural belts. Paleozoic structural belts existed along each coast with deformation gradients diminishing inland toward a narrow, central peninsular craton. The Mesozoic-Tertiary Mexican (Cordilleran) belt covered the entire country with a gradient oriented toward the Gulf of Mexico. Most ore deposits in this belt are of Tertiary age, although Tertiary mineralization gradients seem to have "inherited" the pattern left by Paleozoic tectonic gradients. Mineralization gradients can be used to identify the regions most favorable for the occurrence of selected metals. A metallogenic province is characterized by particular proportions of various metals, and the relative proportions can vary from province to province; but within any province the same intensity of mineralization would produce similar deposits in different places. Declining intensity of minetalization produces different kinds and sizes of deposits in zones that are concentrically arranged around sites of strongest rock alteration. On a regional basis, districts of similar average intensity of mineralization occur in zones that generally parallel some tectonic grain with the result that tectonic deformation has been designated a principal cause of mineralization. Variations in the type and intensity of deformation would determine the type as well as size of metal deposits. Mexico is especially favorable for such a study be- cause of its great abundance and variety of epi-genetic mineral deposits in various lithologic, structural and tectonic environments. The concept is also useful in recognizing portions of Mexico favorable for the occurrence of specific metals. METALLOTECTONIC ZONING IN MEXICO Theory: In studies of individual districts and groups of districts throughout North and South America, areal zoning of metal deposits generally seemed to respond to the paragenetic sequence of iron, gold, copper, zinc, lead, silver, antimony and arsenic, gold and fluorite. However, the definition of district zones is greatly obscured by contemporaneous or rhythmic deposition of metals, especially in the middle of the paragenetic range, and by the common superimposi-tions of different generations of metals. Zones could usually be distinguished only for groups of metals, such as early precious metals, base-metal sulfides, sulfosalts and late precious metals. The best defined zoning in a district is normally the spatial separation of the greatest volumes of altered and metallized rocks.&apos; Exceptions are districts representing the high- and low-temperature extremes of the mineralization range where the former creates a matrix for the latter. In most districts the total quantity of alteration products is greatly in excess of, and appears to be roughly proportional to, the total quantity of metallization products. Subsequent to the bicomponent nature of each district, the most important mineralogical feature is the great excess of one to several metals or minerals which results in a district identifiable as one of predominantly gold, copper, lead-zinc, fluorite, etc., although a great variety of other elements may be present. The para-genetic range for the abundant elements in any district is only a portion of the entire possible range for all the elements representing the complete process throughout the region. Early during investigations of this type, it became apparent that the consistent bicomponent character of districts allows two methods for studying epi-genetic mineralization patterns. One is to identify and plot altered rock "pipes,"* which are easily recognizable in the landscape by their anomalous

Jan 1, 1969

By Anthony Folger, Howard R. Lowe, J. F. Dougherty, E. G. Trostel, Joffre Meyer

The status of the natural gas industry in Alberta, Canada, is described with particular reference to the current extent of natural gas reserves and possibilities for additional development. Certain major fields are discussed as representative of the types of gas accumulations within various broad geographical divisions of the provinces. The estimation of the future performance of a gas reservoir is discussed as the basis for an estimate of the future availability of natural gas from presently known reserves. The future availability of the provincial reserves and the estimated future demand for gas within the province are described. INTRODUCTION This paper is a condensation of a detailed study of the natural gas reserves and the future availability of pipeline gas in the province of Alberta as prepared for Trans-Canada Pipe Lines Limited and presented in public hearings at Edmonton and Calgary before the Petroleum and Natural Gas Conservation Board of the Province of Alberta. The study began in October, 1950, and resulted in the preparation of five volumes of data at the expenditure of more than 20,000 man-hours. This paper is designed to afford a broad picture with detail limited to a type example of both natural ga-accumulation and future availability of gas supply. The province of Alberta has an area of 255.285 square miles which, for sake of comparison. is 8,359 square miles smaller than the state of Texas. Natural gas was first discovered in 1883 at the now abandoned Alderson well located some 20 miles southeast of the town of Princess. The first gas in commercial quantities was found at Medicine Hat in 1890. During the last 68 years. 187 localities have been discovered which are capable of gas production, and 73 per cent of these have been found since 1945. Sixty fields currently are producing gas, including 22 non-associated gas accumulations. Location of the oil and gas fields and prospects in the province of Alberta is shown in Fig. 1, together with a list of the localities of measurable gas, Fig. 1A. The estimated total provincial gas reserve as of Jan. 1, 1952, for the 104 fields estimated, is 11.7 trillion cu ft proved and probable, and for the 187 known areas capable of production is in excess of 16 trillion cu ft on a total proved, probable, and possible basis. Five fields (Pincher Creek, Leduc-Woodbend, Viking-Kinsella, Cessford and Medicine Hat) are estimated to have recoverable reserves of more than one trillion cu ft each. A sixth field, Turner Valley, was initially in this group, but its reserves have been depleted substantially. Twenty-four fields, of which the above mentioned six fields are a part, have estimated gas reserves (including the possible category) in excess of 100 billion cu ft. These 24 fields account for 79 per cent of the total provincial reserves. Comparative systemic analyses reflect that 56 per cant of Alberta&apos;s gas reserves are contained in sediments of Cretaceous age; 30 per cent in sediments of Mississippian age; 10 per cent in sediments of Devonian age; three per cent in sediments of Triassic age; and the remaining one per cent in Jurassic and Permo-Pennsylvanian sediments. It is expected that the relative importance of the Mississippian, Devonian, and Triassic sediments will be increased as exploration progresses. GENERAL GEOLOGY The western Canada basin comprises the sedimentary area between the Canadian Shield and the Rocky Mountain Front Range, the Arctic Ocean, and the International Boundary. The basin has an approximate area of 765,000 square miles and embraces parts of the provinces of Manitoba. Saskatchewan. Alberta, British Columbia and the Northwest Territories. Generalized columnar sections for the Province of Alberta are shown in Fig. 2. Substantially all of Alberta, except its northeast corner, has sedimentary cover. Sediments of all the geologic systems are represented. except those of Silurian age.

Jan 1, 1952

By John D. Morgan

THE tense international situation prevailing in the postwar period, and the outbreak of actual hostilities in Korea, directs attention to the status of United States reserves of strategic and critical materials for war. Geologists and mining and metallurgical engineers are particularly interested in this problem, since, with a few important exceptions, almost all of the materials on the official list of strategic and critical materials for stockpiling (see top of page) are metals and minerals.

Jan 3, 1951

By A. K. Isaac

The effectiveness of coalface powered support depends upon its structural nature and the manner of application of the hydraulic system. A critical and largely unresolved feature of the system is the optimum setting pressure level at which a support should operate in its geological environment. This paper provides an argument for a generalised approach to the issue of setting pressure level quoting case study data for a high output British longwall installation.

Jan 1, 1984

By L. P. Bayvel

The method of spectral transparency was investigated. A device for measuring particle sizes based on this method was developed, tested and applied. The device affords measurements of particle size distribution in the range from 0.1 to 4 µm. It proved possible to measure sizes not only of spherical particles but also of non- spherical ones. The spectral range in which it is necessary to determine transparency for particle size measurements was found.

Jan 1, 1980

By Lap-yan Chan

Chan and Goodman (1983) presented a procedure for simulating joint traces and identifying key blocks on an excavation. This paper defines six measures of support requirements that characterize the number and dimensions of key blocks, taking into account the frictional properties of joints and actions of support systems. When correlated with case histories, these measures of support requirements can help in choosing an optimal design for shallow excavations in discontinuous hard rocks.

Jan 1, 1984

By Stewart K. Griffiths

A general method-of-lines numerical approach for modeling gas driven fractures has been developed and tested. The numerical solutions agree very well with known similarity solutions for laminar and turbulent flow. Acceptable accuracy is obtained with a very few numerical grid points and with modest execution times. The model has also been checked against the results of several field tests, in which air was used to drive axisymmetric fractures into permeable tunnel-bed tuff.

Jan 1, 1984