Search Documents

By R. Chanchani

Single and mixed mineral flotation behavior and the mechanisms for the loss of selectivity in 1:1 and 95:5 apatite: dolomite mineral mixtures are presented. Loss of selectivity in mixed mineral systems is attributed to depletion of oleate ions available for adsorption by bulk precipitation with calcium and magnesium ions dissolved from dolomite. Flotation after two-stage conditioning was found to be a potential technique to separate dolomite from apatite. This method involves conditioning at pH 10 followed by reconditioning at a lower pH. The results indicate that selective flotation of dolomite, a minor mineral in south Florida phosphate deposits, could be obtained by reconditioning at pH below 4.5. Higher selectivity was observed for mixed minerals as compared to that of single minerals.

Jan 1, 1986

By H. Sato, R. J. Lipp, I. Iwasaki, K. A. Smith

Selective desliming holds much promise for upgrading low-grade, finely disseminated iron ores that are not readily amenable to conventional flotation. The process is extremely sensitive to the presence of calcium and magnesium ions that are in process water or are released by constituent minerals. The effects of these two alkaline earth ions on quartz were compared through streaming potential measurements, flocculation and cationic flotation tests, abstraction tests and scanning electron microscope studies. Calcium ion, adsorbed as CaOH+, and magnesium ion, attached by heterocoagulation as Mg(OH)2 precipitate, were responsible for the flocculation of quartz suspension and for the depression in cationic flotation of silica in alkaline pulp solutions. Magnesium hydroxide coating could be removed, similarly to adsorbed calcium ion, by complexation with EDTA and polyphosphates.

Jan 1, 1980

By Selma Hermann

For the past century, the so-called aluminum bronzes have been assuming a role of ever-increasing importance in the metallurgical field. The last quarter of that century has marked many efforts to find alloying elements that would alleviate some of the undesirable qualities of the aluminum bronzes-for example, the heterogeneity of the alpha solid solution and the extreme hardness of the beta. Much of this work, however, has been rather haphazard-compositions and heat treatment are usually so much at variance as to make comparison impossible. It is the object of this research to study the effect of certain percentages of common alloying elements on aluminum bronzes of analogous compositions and heat treatments. It is hoped that the material gathered here will at least serve as a basis for further systematic study.

Jan 1, 1930

IN the western mines, the boss, engineer, geologist, or nipper in making rounds have a password which usually guarantees safe entrance to a working place from below the working miner. Most men won't climb a raise or enter a stope from below where a miner is working until they have shouted "nothin' down" and heard those words shouted back by the miners above. "Nothin' down" is a safety pledge as necessary and as binding as the truce flag to the soldier. It implies mutual confidence that work will be suspended until the person below has come abreast of the workers; and also confidence that the miner who replies "nothin' down" is reasonably sure the place is safe to enter. Like truce flags which are not infallible, so is this password subject to human errors or unexpected falls of rock, tools, or timber. Everyone knows these unavoidable hazards, but what is important to the exposed man is that in that precise moment of time when he has heard the reassurance of "nothin' down," he knows that safety is uppermost in the minds of the men above him. With such assurance we would go anywhere and so would most mining men. If that period of safety consciousness, procured by the utterance of two words, could be multiplied to equal the hours in the working day, there would not be any accidents but those by "the act of God." It is the aim of every safety program to make safety as natural as breathing. That is the reason for the posters, the conferences, instruction periods, safety engineers, and the inspections. But none of these are as effective as one accident, which keeps men on their toes for weeks to come. This is not the price we want to pay for safety consciousness. This Annual Review number of Mining Engineering is full of talk about production. Production for defense, production for profit. In this tremendous surge of industrial might . to make this nation and our very families safe S from the predatory forces abroad in the world today; let us not lose sight of the fact that the . safety of our manpower is more precious than any commodity. Production without safety is detrimental to the national interest, to that of the company, and to the individual. If the words "nothin' down" can give us the best human guarantee of safety, for however brief a time, let us adopt them at least in principle as our slogan in 1952. Production for preservation in '52 - but NOTHIN' DOWN!

Jan 1, 1952

The Rio Tinto - Cerro Colorado operation was the first major cyanide plant built out of South Africa since the Carlin and Corte mills came on-stream in 1965 and 1969. Its flowsheet was presented in the original monograph, "Gold and Silver Cyanidation Plant Practice, " published in 1975, with a brief description of the plant but without the operating costs. The authors have recently received these data and it was believed worthwhile to present them in this volume along with the aforementioned flowsheet. The Cerro Colorado ore deposit is located at Minas de Rio Tinto in the province of Huelva, Spain, approximately 88 km (55 miles) north- west of Seville. The previously mined copper ore bodies lie on either side of the deposit which is mainly copper ore. The crest of the deposit is a capping of "gossan" containing hematite, limonite, gold, and silver. Separate facilities for primary crushing, concentration of copper ores and cyanidation of gold-silver ores are provided. Fine crushing is common to both ores. The run-of-mine open-pit ore is fed from a stockpile via a surge bin and apron feeder to a jaw crusher. After crushing to minus 150 mm (6 in. ), the ore is washed in a rotary scrubber to remove the clay material ahead of fine crushing. Minus 6 mm (1/4 in. ) screen undersize is pumped directly to the grinding circuit with the screen oversize being crushed to minus 19 mm (3/4 in. ) for feed to the primary ball mill; this is followed by two subsequent stages of ball mill grinding to 80% minus 43 microns (325 mesh). Grinding is with water only; no cyanide is used. After thickening, lime is added to the first two of seven Pachuca tanks for conditioning ahead of cyanide addition in each of the five remaining Pachuca tanks. This flowsheet indicates rapid cyanide consumption and the need to maintain a high strength cyanide solution for silver extraction. Agitation for dissolution of the gold and silver is followed by standard CCD practice employing four 67 m (220 ft) washing thickeners in series, with repulping between each thickener. A departure from American and Canadian practice is the use of Stellar filters developed in South Africa for pregnant solution clarification and recovery of zinc-gold-silver precipitates. The precipitate is treated with acid for zinc removal, the sludge filtered in presses, dried, calcined and smelted to produce dore bullion of 900 fineness containing 12% gold and 78% silver.

Jan 1, 1981

By L. G. Huntley

Discussion of the paper of L. G. HUNTLEY,. presented at the San Francisco meeting, September, 1915, and printed in Bulletin No. 102, June, 1915, pp. 1333 to 1349. E. W. SHAW, Washington, D. C. (communication to the Secretary*). -The comparatively great extent and uniform character of the Dakota sandstone make it of great interest to the student of rock pores and the movements of their fluid contents. However, compared with other sands in areas of carbonaceous rocks facts concerning it do not seem to be of such great direct importance to the producer for it has thus far yielded few important pools of oil or gas. Information concerning the sandstone is extensive but scattered, hence a general treatise regarding it-particularly its pores, the fluids they contain, and the movements of the fluids-has been much needed. I therefore feel that the. chief thing to be ,desired concerning Mr. Huntley's paper is that it were more extended, particularly as to the discussion of the data presented. The general structure map of the Dakota is of especial interest. Slight changes in wording seem to be desirable here and there in the paper. For example, at the beginning of the third paragraph one-wonders if flora instead of fauna were not intended. In Figs. 2, 3, 4, and 5 the vertical scale seems incorrect. Concerning the analyses of oil quoted it is noted that they "are given, as indicating what may be expected in different localities." This seems to need modification for the average analysis of oil from Powder River, which indicates for example that this oil begins to boil at 213°C. The fact is that the samples to which this figure refers were taken from seeps long exposed. to the air :find hence the underground Dakota oil of this district no doubt differs profoundly from that which the analysis indicates. The product of a well here would probably differ more in boiling point and other. respects from the samples analyzed than it would from almost any other petroleum in the world. The use of the word synclinorium does not conform to the original definition, but this may be pardonable because misuse of the term, though a different misuse, has become general. Synclinorium is an orographic term and cannot be correctly applied outside of mountain regions, for it is derived in part from the Greek word for mountain. It has, however, been widely used in a purely structural sense for compound syncline. The broad shallow syncline of the Dakota sandstone falls in neither category. Objection might also be made to the use of

Jan 12, 1915

By S. S. Clarke

THEN sufficient ore has been blocked out on a lease to warrant a shaft, the proposed. Location of the shaft should be carefully considered, as the old promoter's method of sinking wherever his hat landed is a sad mistake as some: of us have learned by trying to operate such mines. In some instances certain conditions exist, such as mill location, railroad right of way, etc., that necessitate a change of location from the. ideal, but under average conditions and with the knowledge of the formation gained from the drill logs and with the general trend of the orebody known, the shaft can be located from. the standpoint of its future relation to the mine with re-gard to hauling and' hoisting a maximum tonnage: at a minimum cost per ton, also taking into account the minimum amount of expense and trouble- in sinking. Quite a few shafts are located in the wall of a run or just in the thin edge of the orebody: As a general rule the formation here is solid and permits rapid and safe sinking, and the shaft pillars are left in practically valueless material. This permits the withdrawal of pillars and still keeps the shaft protected. By opening a shaft in thin ground, you are not tempted to cut it high, wide, and handsome, but to shape it up-with ample clearance for lay-bys and with more of an idea of permanency, as a few hundred extra dollars spent around the shafts for proper track installation will re-turn, a good rate of interest in ease of handling "cans," quick get-away; and fewer wrecks. Nearly all the shafts in this district are sunk on a contract basis, the con-tractors furnishing all labor and explosives, and the company building the sinking-derrick, dump-track, and furnishing, all equipment, material, and power. The following costs are the averages, for three shafts sunk through good solid formation, with no water to, contend with, and approximately 260 -ft., deep, having about-100 ft. of shale. The contract price was $9 per foot with the shale and $13 per foot in the solid, making a total of $2,980 paid to the contractor. The wages paid by the contractor were, $5 per shift for the hoist-man, who also sharpened steel, $6 for the lead shaft man, and $5 for the helper;, the cribbing was sawed on contract for 40c. per shaft: foot; about. 94 board feet. of cribbing was used per foot of staggered cribbing and 168 board feet per foot of solid cribbing.

Jan 8, 1928

By Coopers &. Lybrand

INTRODUCTION From a tax viewpoint, United States mining companies are at a substantial disadvantage in the international mining area compared with companies in other major capital-exporting countries, according to a 1975 study by Coopers & Lybrand for the American Mining Congress. The study compared the relative tax position of a United States investor with investors from Belgium, Canada, France, Germany, Japan, the Netherlands, Switzerland, and the United Kingdom. The comparison was based on average rates of return realizable by investor companies on four mine-model investments in twelve capital-importing countries. The countries in which these investments were assumed to be made are varied in their tax systems so that a wide range of possibilities was included in the analyses. Each mine model was standard so that the rates of return for each investment by each investor were affected solely by the respective tax systems of the capital-exporting and capital-importing countries. UNITED STATES POSITION The study found that the United States competitive position, in terms of the average rate of return on an overall basis, ranked next to last among the nine capital-exporting countries in the study. Further, the United States overall rate of return is more than 20% below that of the country (Japan) with the highest overall rate of return. On an average return-on-equity basis, the United States' position among the nine investor countries, for each of the mine investments studied, was: copper, eighth; iron ore, sixth; nickel, fifth; manganese, a tie for last place. Figure 1 shows the overall results realized by each capital-exporting country on the basis of average return on equity. [ ] The frequency with which a given capital-exporting country attains the highest or next highest rate of return in a capital-importing country provides further insight and another basis for comparing the tax laws of the capital-exporting countries. Of the situations compared in the study, the United States never attained the highest rate of return, and reached the second and third highest rate of return in only two instances. The tables showing the frequencies of rankings are given in Table 1 for each of the four mine models. In summary, the United States mining company does not have a competitive advantage under the tax rules when competing for mineral concessions in other countries. The United States company, in fact, appears to be at a clear disadvantage. The study also considered the effect of the following recent tax proposals on United States investors in international mining ventures:

Jan 1, 1985

By W. N. Best

This paper is not intended as a scientific discussion of the combustion of oil but is written from the standpoint of an operator who has the experience and qualifications necessary to guide others in producing the most economical results in the use of liquid fuels. Oil, in this paper, usually means petroleum or its products but incidental reference is made to other liquid and gaseous fuels, so that the term may be considered as referring to all liquid and gaseous hydrocarbons in comparison with solid fuels, as coal and wood. However, only a few of the principal factors in the use of oil as a fuel can be given. The present, and prospective, high price of coal is causing users of fuel to renew inquiry as to the merits of other forms of fuel for industrial purposes. Crude oil (petroleum) is proving to be one of the world's most valuable mineral resources. The recent discovery that oil underlies a considerable area of the United States, Mexico, and other parts of the world to a greater extent than was formerly believed and the large production of some of the wells in these areas shows the probable quantity of fuel oil that may now be available. Through the energy of Lord Cowdrey, who was one of the pioneers of the oil industry in Mexico, oil has been discovered in England; some prominent geologists believe that it may be found in quantity in Great Britain. For years, oil has been known to be of great value in the manufneture of metals. It has proved incomparable in forge shops, steel foundries, heat-treating furnaces, and wherever accuracy of temperatures is essential, or where a maximum output is desired as well as quality of metal. In some types of equipment, the output produced with oil as fuel is double that obtained with coal and at a reduction of 50 per cent. in the cost of the fuel. For example, in drop-forging plants, the metal is always waiting for the man when oil is used as fuel, whereas with coal, the man must wait for the metal to become sufficiently heated. It has only been since January, 1919, that the oil supply could be relied on for boiler service, owing to the war conditions and the inability to get oil tankers for the delivery of the oil from Mexico to Atlantic ports; but now a constant supply is assured, and many manufacturers are installing it in their power plants. The cost varies with the size of the

Jan 1, 1921

By J. B. Darby

In an investigation of various equiatomic alloys of transition elements, Dwightl did not find evidence for the CsC1-type ordered structure in VMn. More recently waterstrat2 has reported the occurrence of this structure in the alloy his sample had been homogenized at 1150°C and subsequently reannealed at 725°C after crushing to powder. The purpose of this note is to confirm the existence of the CsC1-type ordered structure in VMn and to report a lattice parameter. An equiatomic alloy was prepared by arc-melting under an argon atmosphere vanadium and electrolytic manganese having a purity of at least 99.9 pet. The composition was obtained by charging an excess of manganese and monitoring the weight loss until the stoichiometric composition was achieved; the assumption that the loss during melting was due to the vaporization of manganese appears to be a valid one.' The calculated composition of the sample prepared was 49.85 at. pct V and 50.15 at. pct Mn. Specimens taken from the fractured as-cast buttons were wrapped in molybdenum foil and encapsulated in quartz capsules under vacuum; there was no evidence of a reaction between the alloy and foil. The X-ray patterns were obtained using filtered copper or chromium radiation with a Straumanis-type Debye-Scherrer camera having a diameter of 114.6 mm. The CrKa radiation is best suited for detecting the superlattice lines since it overcomes the slight difference in scattering powers of the components by making use of the anomalies in atomic scattering factor which occur when the frequency of the radiation is close to the characteristic absorption frequency of one of the elements.394 A specimen in the as-cast condition, as well as one which had been annealed for 1 week at 900°C and water-quenched, gave a diffraction pattern for the disordered bcc solid solution. However, when samples were homogenized at 900°C for 3 weeks followed by a subsequent anneal at 700°C for 6 to 7 weeks and then water-quenched or furnace-cooled, the (loo), (1111, and (210) Ka superlattice lines were observed in films taken with chromium radiation. An ao = 2.904 * 0.001 was determined by a Nelson-Riley extrapolation from a film taken with CuKa radiation. The author wishes to thank Mr. J. W. Downey and Mr. L. J. Norton for carrying out the experimental portion of this investigation. This work was performed at the Argonne National Laboratory under the auspices of the U.S. Atomic Energy Commission.

Jan 1, 1963

By George Mah, Charles Wert

Internal-friction peaks caused by diffusion of oxygen and nitrogen have been observed in ytterbium. They are thought to be caused by the redistribution, under stress, of strain dipoles around an interstitial oxygen or nitrogen and a neighboring substitutional impurity. With the use of a simple geometrical model, diffusion coefficients for oxygen and nitrogen between special interstitial sites have been calculated. a) APPLICATION OF INTERNAL FRICTION TO MEASUREMENT OF DIFFUSION RATES IN DISSOLVED INTERSTITIAL ATOMS In bcc metals, the interstitial atoms occupy the centers of cube faces (0, 1/2, 1/2), or their equivalents, the center of the cube edges (0, 0, 1/2). An interstitial atom in this position causes an aniso-tropic distortion in the lattice. When stress is applied, mechanical relaxation can take place by the movements of the interstitial atoms. This relaxation has been used to obtain information concerning the movements of the interstitial atoms in the bcc metals. Data for these alloys have been compiled by Stanley and Wert. Other researchers have extended the investigation of interstitial diffusion to the close-packed metals. Gupta and weinig2 found an oxygen peak in a titanium, the height of which is linearly dependent on the oxygen concentration. They assumed, therefore, that they were dealing with movement of atomic ally dispersed oxygen in titanium. KG and wang3 determined that the diffusion coefficients of carbon in fcc steels and in nickel obtained by internal-friction methods were consistent with those obtained by macrodiffusion methods at much higher temperatures. Bisogni found oxygen and nitrogen peaks in hafnium by use of which he deduced the diffusion coefficient of these gases in hafnium. He observed further that the half-widths of these peaks corresponded almost exactly with those of a single-relaxation process; he assumed it to be caused by movement of atomically dispersed oxygen and nitrogen. From these studies, the deduction can be drawn that, in general, diffusion data can also be obtained for the interstitial diffusion in close-packed metals (or more precisely, in slightly impure close-packed metals). One group of such metals for which little data exist for the diffusion of dissolved oxygen and nitrogen is the rare earths. They have great affinity for gases, which enter solution interstitially. In this investigation results were obtained for the Yb-O and Yb-N interstitial solid solutions with traces of substitutional impurities; these solid solutions are of fcc structure. b) MECHANISM OF THE RELAXATION IN FCC CRYSTALS In the fcc structure, an interstitial gas atom is usually situated in the octahedral position (1/2, 1/2,

Jan 1, 1964

By Howard C. Dunkle

Various factors can affect the quality of B1112 and B1113 steel as produced in a bessemer plant; among them: vessel-charging practice, blowing practice, ingot-pouring practice, ingot delivery-time practice, pit-heating practices, and ingot-rolling practice. Evaluation of the influence of ingot delivery time on quality has been chosen as the subject for this paper because this time is completely within the control of the operator, and on this particular factor there is a tremendous amount of information in the dusty archives of the average steel plant. In order to know how much improvement can be made and when attention should be directed to other factors that influence quality, in the continual struggle for improvement, the effect of ingot delivery time must be accurately evaluated. Once this is done, the importance of other variables can be accurately obtained, thus eliminating the necessity of resorting to opinions that are of doubtful value at best. In the study described herein, extensive use was made of the statistical card system as a method of determining the effect of ingot delivery time as a quality factor in bessemer screw-stock grades by simple direct correlation. The value of this statistical method as a means of accurately determining the influence of various factors has been amply demonstrated by Work1 for the bessemer process and by Hand and Gould2 and Fetters and Chipman3 for the open-hearth process. The quality records of 300,000 tons of bessemer screw-stock billets were used in this study of the effect of ingot delivery time on the rejections for breaks, pipe, check and seams. The reduction in the number of rejections for poor quality reduces the costs and increases the productivity per man-hour. The operator today, more than ever before, must know how to keep costs down, how to do it most quickly and in the best way, and how to obtain the highest quality in line with the ever increasing demands of the customer. It is necessary for him to know the individual relations and interrelations between various factors affecting the quality of the manufactured product if he is to produce material that will meet competitively the cost, performance, and quality demands of the trade. SIGNIFICANCE OF STEEL MANGANESE, MIXER SILICON AND STEEL SULPHUR AS QUALITY FACTORS In order to obtain the highest grade of material it is necessary to control many factors-not just one or two, as operators

Jan 1, 1945

By Harry H. Power

While the attention of all engineering branches is focused today on changes and improvements in the several curricula, we are concerned here with the many questions arising in industry and college concerning the preparation for the petroleum engineering profession. The succession of problems confronting the petroleum engineer demands a degree of versatility not ordinarily encountered in other professions. As a consequence, the student cannot acquire mastery of all the several engineering branches represented in field practice, and as an alternative, he has learned to appreciate the value of thorough training in the basic or fundamental sciences as a Preliminary foundation for professional work. While our attention is directed primarily to the training of engineers in educational institutions, it is necessary that the ultimate education of the professional engineer be kept in mind. It is apparent that his success as an engineer is limited not only by his educational and job experience, but by his native endowments: mentality, Personality and health. The engineer's lack of job experiences often proves as much a handicap as the lack of adequate college training. If the final product proves to be satisfactory, both industry and technical institutions are to be congratulated. However, if the Product is found wanting, the one most responsible should For the most part, students of engineering colleges have had their interests in applied science awakened at a relatively early age. Manyof them entered college as a convenient means of acquiring a technical education, but undoubtedly would have had better prospects in a shorter program offered by institutions of non-college grade. The activating motive of practical interest is also strong in students suitable for college training, but in many cases an intellectual interest must be awakened in order that it may survive graduation. Numerous engineers believe that this progressive process of selection and determination of career aims is one of the essential services rendered by the engineering colleges. Industrialists, who are more inter. ested in quality than quantity of petroleum engineering graduates, have pointed out the good that should result if more emphasis were given to the work of eliminating the misfits. They also point out the protective measures that have been taken by other professions for the betterment of professional standards. Mention has been ,de of the beneficial results to be obtdned by collective determination of the market for the products of engineering schools, particularly in that the students unsuited to the profession would have an opportunity to prepare themselves for employment more suited to their personalities and other qualifications. In the event that such a system of coordinated personnel direction is developed by the

Jan 1, 1941

By Howard C. Dunkle

Various factors can affect the quality of BIII2 and BIII3 steel as produced in a bessemer plant; among them: vessel-charging practice, blowing practice, ingot-pouring practice, ingot delivery-time practice, pit-heating practices, and ingot-rolling practice. Evaluation of the influence of ingot delivery time on quality has been chosen as the subject for this paper because this time is completely within the control of the operator, and on this particular factor there is a tremendous amount of information in the dusty archives of the average steel plant. In order to know how much improvement can be made and when attention should be directed to other factors that influence quality, in the continual struggle for improvement, the effect of ingot delivery time must be accurately evaluated. Once this is done, the importance of other variables can be accurately obtained, thus eliminating the necessity of resorting to opinions that are of doubtful value at best. In the study described herein, extensive use was made of the statistical card system as a method of determining the effect of ingot delivery time as a quality factor in bessemer screw-stock grades by simple direct correlation. The value of this statistical method as a means of accurately determining the influence of various factors has been amply demonstrated by Work1 for the bessemer process and by Hand and Gould2 and Fetters and Chipman3 for the open-hearth process. The quality records of 300,000 tons of bessemer screw-stock billets were used in this study of the effect of ingot delivery time on the rejections for breaks, pipe, check and seams. The reduction in the number of rejections for poor quality reduces the costs and increases the productivity per man-hour. The operator today, more than ever before, must know how to keep costs down, how to do it most quickly and in the best way, and how to obtain the highest quality in line with the ever increasing demands of the customer. It is necessary for him to know the individual relations and interrelations between various factors affecting the quality of the manufactured product if he is to produce material that will meet competitively the cost, performance, and quality demands of the trade. Significance of Steel Manganese, Mixer Silicon and Steel Sulphur as Quality Factors In order to obtain the highest grade of material it is necessary to control many factors—not just one or two, as operators

Jan 1, 1945

By I. L. Dillamore

A purely geomentrical analysis based on oriented-growth relationships is presented to derive annealing-texture orientations in bcc metals from their- known deformation textures. The analysis takes as its starting point a description of- the bcc deformation texture and follows previous work on fcc metals in considering pvobable nurleation sites for recrystallization and the textural limitations on grains growing into a deformed matrix. The analy-sis accounts for the prominent and the minor coinponents of the annealing textures formed from two the deformation textures and can account for the ob-sem:ed temperature dependence of the annealing texture of bcc metals. THERE have been a number of investigations of annealing textures in bcc metals but few attempts to relate these textures to the deformation textures. This has been largely due to the lack of definition of both annealing and deformation textures, neither of which shows sharply defined orientations. It is, however, necessary to get a better understanding of primary recrystallization textures in bcc metals in view of increasingly exacting demands upon the quality of steel sheet for drawing purposes and as a necessary step towards the control of textures through processing. An analysis is presented here which relates annealing textures to deformation texture, by a purely geometrical method. This takes as its basis the oriented-growth theory of recrystallization and makes some reasonable assumptions regarding the make-up of bcc deformation textures and the limitations on growth relationships in bcc metals. Detailed information on this latter point is not available at the present time, and the present analysis may need to be streamlined or extended when such information is at hand. It is felt, however, that despite these limitations the analysis provides useful results and a valuable aid towards understanding the effect of processing variables. 1) BCC ROLLING TEXTURES Different workers have used a variety of descriptions for the texture developed in bcc metals by rolling. For the present purpose it will be assumed that two different deformation textures can be obtained: 1) a texture containing a major (112)[li0] component and a minor (001)[1i0] component for which increasing deformation causes the (001)[li0] component to increase at the expense of the (112)[li0] component, as suggested by Dillamore and ~oberts' (this is the texture predicted to arise starting from randomly oriented material); 2) a t~xture containing the above components and (111)[110] and (ii1)[112] components. This texture could arise from a material with an initial (110)[001] or (iil)[112] texture. It is well-known that the (ll0)[001] orientation rotates to (ii1)[112]that on roll-

Jan 1, 1965

By T. D. Guldem, J. L. Kaae

ALLOYS with nominal composition of 45-Fe 35-Ni 20-Cr, ASTM-B-163, known under the commercial names of Incoloy 800 and Sanicro 31 (Alloy 800), are often employed at elevated temperatures for extended periods. Therefore, knowledge of the aging behavior of these alloys is of considerable importance. Significant decreases in ductility and increases in yield strength have been observed in the 45-Fe 35-Ni 20-Cr alloys containing about 0.4 pct Ti and 0.4 pct A1 after long-term aging at 540" to 700"~."~ However, no direct evidence has been presented for precipitation phenomena that might result in such changes. Strengthening effects have been attributed to the effects of local or-dering.3 Since y' precipitation (Ni3A1, Ti) is known to occur in similar alloys which contain more titanium and aluminum,4-7 it was decided to explore the possibility that y' might precipitate in these alloys and might be responsible for the changes in mechanical properties on aging. This note reports some observations of two distict types of matrix precipitates made by means of transmission electron microscopy, in a 45-Fe 35-Ni 20-Cr alloy containing 0.31 pct Ti and 0.4 pct Al. The steel used in this investigation was obtained from the Sand-vik Steel Works; it is designated Sanicro-31 (Alloy 800). The chemical composition of the alloy is given in Table I. Aging of solution-treated material at 700" and 800°C for 130 and 100 hr, respectively, produced the matrix precipitates shown in Figs. l(a) and l(b). It is apparent from these micrographs that the precipitate particles occurred in the form of thin square plates parallel to the matrix cube planes. Extraction replication and selected-area electron diffraction showed that the precipitates were M23C6. Coherency strains, consistent with the semicoherent nature of small M23C6 precipitates,' were evident for certain imaging conditions. In addition to matrix precipitation, preferential precipitation of M23C6 on dislocations was common, as has been reported previously for austenitic stainless steels.'" Specimens aged for longer times (-300 hr) at 700°C exhibited a different type of coherent matrix precipitate in addition to the M23C6. An example is shown in Figs. 2(a) and 2(b). In addition to the few large M23C6 precipitates, small precipitates exhibiting strain contrastl0,ll are present. The "line of no contrast" of the strain field of a given precipitate lies along differ-

Jan 1, 1970

By Arthur Tauber, Horst Kedesdy

FERRITES are sintered metallic oxides of the spinel structure type1 and belong to the class of soft ferromagnetic materials. Similar to a ceramic, they can be formed and fired to a dense body, exhibiting a high electrical volume resistivity ranging from 10 90 10' ohm-cm as compared with 10-6 hm-cm for some of the metallic magnetic materials. This high resistivity, with resulting low eddy current losses, finds special application at high frequencies. The dispersive susceptibility of ferrites at microwave frequencies has also led to many applications in this field. Where high resistivity with high permeability is desirable, ferrites are used in low frequency applications. During the last few years ferrites exhibiting rectangular hysteresis loops have been developed for computer and magnetic memory systems. The general formula for ferrites is MeFe2O4 where Me is a divalent metal ion such as Ni, Zn, Mg, Mn, Cu, Cd, and Fe. Only two of these ferrites are nonferromagnetic, namely, those with Zn and Cd. Solid solutions can be formed between different ferrites, and it is of interest to note that solid solutions of a ferromagnetic ferrite with a nonferromagnetic ferrite yield much better magnetic materials than the basic ferrite body. In general, it can be said that the solid solution formation between ferrites has widened the field of ferrite synthesis and has led to methods of preparing materials with a large variety of magnetic properties. During the last two decades the synthesis of ferromagnetic oxides has been the object of extensive research, but commercial production has been started only within the last ten years. Along with more fundamental studies, there remains the never- ending task of developing ways to realize the optimum characteristics of materials in large-scale production. Ordinarily, to produce a ferrite material it is necessary for the constituent oxides to be mixed intimately, pressed, and then fired at temperatures above 1000°C. Ferrite Synthesis: Formation of a basic ferrite by solid state reaction from Fe,O, and a monoxide such as NiO, under normal atmospheric conditions, is governed by a progressive diffusion of cations between adjacent particles of the constituents. Firing temperature, furnace atmosphere, and cooling can vary the magnetic properties, however. If, for example, a dioxide, a sesquioxide, or an oxide of the Me0 type is substituted for the monoxide, the reaction mechanism becomes more complex and extremely dependent on atmospheric conditions and firing cycles. For this reason reproduction often

Jan 1, 1958

By Harry H. Power

While the attention of all engineering branches is focused today on changes and improvements in the several curricula, we are concerned here with the many questions arising in industry and college concerning the preparation for the petroleum engineering profession. The succession of problems confronting the petroleum engineer demands a degree of versatility not ordinarily encountered in other professions. As a consequence, the student cannot acquire mastery of all the several engineering branches represented in field practice, and as an alternative, he has learned to appreciate the value of thorough training in the basic or fundamental sciences as a Preliminary foundation for professional work. While our attention is directed primarily to the training of engineers in educational institutions, it is necessary that the ultimate education of the professional engineer be kept in mind. It is apparent that his success as an engineer is limited not only by his educational and job experience, but by his native endowments: mentality, Personality and health. The engineer's lack of job experiences often proves as much a handicap as the lack of adequate college training. If the final product proves to be satisfactory, both industry and technical institutions are to be congratulated. However, if the Product is found wanting, the one most responsible should For the most part, students of engineering colleges have had their interests in applied science awakened at a relatively early age. Manyof them entered college as a convenient means of acquiring a technical education, but undoubtedly would have had better prospects in a shorter program offered by institutions of non-college grade. The activating motive of practical interest is also strong in students suitable for college training, but in many cases an intellectual interest must be awakened in order that it may survive graduation. Numerous engineers believe that this progressive process of selection and determination of career aims is one of the essential services rendered by the engineering colleges. Industrialists, who are more inter. ested in quality than quantity of petroleum engineering graduates, have pointed out the good that should result if more emphasis were given to the work of eliminating the misfits. They also point out the protective measures that have been taken by other professions for the betterment of professional standards. Mention has been ,de of the beneficial results to be obtdned by collective determination of the market for the products of engineering schools, particularly in that the students unsuited to the profession would have an opportunity to prepare themselves for employment more suited to their personalities and other qualifications. In the event that such a system of coordinated personnel direction is developed by the

Jan 1, 1941

By Enid C. Plante

INTRODUCTION To extend our knowledge of the flotation behavior of sulphide minerals, the response of the following minerals to ethyl xanthate as collector was studied by captive bubble and cylinder flotation tests: antimonite (Sb2S3), arsenopyrite (FeAsS), covellite (CuS), marcasite (FeS2), orpiment (As2S3), pyrrhotite (FeS) and tetrahedrite (4CU2S, Sb2S3). Lollingite (FeAs2) was also examined to determine if its behavior could be correlated with that of pyrite or marcasite (FeS2). EXPERIMENTAL METHOD Mineral for Flotation and Contact Tests Mineral was prepared in the manner already described' and its behavior both freshly ground and "oxidized" was studied. Tests in which the mineral was allowed to oxidize for various periods showed that a uniform response to xanthate was reached in two days or less. Oxidation Products The soluble oxidation products from most of the above minerals were measured and their effect on the flotation of the mineral studied. The mineral samples were wet ground to minus-52 mesh and deslimed, and 20 g of this material placed in 200 ml of distilled water of a measured pH value, and C02 free air bubbled through each suspension at a constant rate (about 1 bubble/sec) for 5 days. It has been shown1 that the size of the mineral is unimportant in the rate of formation of oxidation products and that probably the supply of oxygen to the mineral is the rate-determining step. At the end of 5 days the pH value of the supernatant liquid was measured again, the mineral filtered off and the soluble products determined. Methods for estimation of sulphur acids, ferrous and ferric iron and copper have already been described.1 No satisfactory method was found for antimony. Arsenic was estimated as the arsenate.2 FLOTATION OF "UNOXIDIZED" MINERALS WITH ETHYL XANTHATE AS COLLECTOR Fig I to 3, 4, 6, show the effect of alkali and cyanide as depressants for the minerals with 25 mg potassium ethyl xanthate per liter as collector at 35°C. Wark and Cox3 have shown that with ethyl xanthate as collector, galena, pyrite and chalcopyrite show a greater tolerance to cyanide and hydroxyl ions at room temperature than at 35°C. Covellite (Fig I), marcasite (Fig 2) and pyrrhotite (Fig 3) behave similarly. The independence of the curves for pyrrhotite at 35°C with respect to cyanide

Jan 1, 1947

By R. A. Vandermeer, Paul Gordon

On the basis of a unified concept, theoretical erPressions for grain boundary migration in recrys-tallization are derzved for impurity-controlled and impurity-independent migration. The expression in the former case is analogous to that Previously derived by Lucke and Detert, and in the latter is shown to be equivalent to that usually obtained on the basis of absolute reaction rate theory. The equations are tested with quantitative experimental data for boundary migration obtained for the recrystallization of poly crystalline zone-refined alumimnz and for binary "alloys" of this aluminum with 0.00021, 0.00043, 0.0017, 0.0034, 0.0068, 0.0124, and 0.0256 at. pct Cu, respectively. All the essential characteristics of the e@erimentally determined boundary migration rates check both qualitatively ard quantitatively with the predictions of the theoretical equations. THE rates of transformations are customarily analyzed phenomenologically in terms of the two component rates—N, the rate of nucleation and, G, the rate of growth of the nuclei. The scientific aim of both theory and experiment is to describe the fundamental atomic phemmena involved in these two component processes with the hope that parameters calculated from theoretical equations will check those found experimentally. In solid state transformations, the theoretical and experimental problems are both generally of almost prohibitive complexity, for in addition to changes in composition and in such properties as density which may accompany transformations in amorphous, nonrigid materials, transformations in crystalline substances also involve structural changes, crystal reorientations, and the development of stresses. In studying such transformations it thus becomes; highly desirable, if not essential, to focus on a transformation and a set of conditions which minimize the number of active variables. This principle has been applied with considerable success by Cohen and his associates' in their evaluation of nucleation theories using the martensite transformation as the basis of study. A similar possibility exists for the evaluation of growth theories by the use of recrystallization after cold-deforming. If an unalloyed metal is employed as the subject of investigation, the recrystallization transformation involves basically only a change in strain-conditions and orientations. In spite of this possible simplilfication, however, until recently little quantitative success has attended attempts to correlate recrystal1ization parameters measured experimentally with those calculated theoretically. It seems highly probable that this lack of success may be attributed, both in the experimental and theoretical treatments, to one or more of the following factors: a) conditions have usually been studied under which apparently* both nucleation and growth are active;

Jan 1, 1962