Search Documents

By G. H. Rowe, A. N. Stroh, D. P. Gregory

The magnitude and variation with strain of the parameters activation volume, V*; activation energy, H; and frequency factor, A, in the Arrhenius equation for strain rate are determined for colunlbium single crystals and polycrgstals. Comparison of dislocation structures in deformed columbium crystals as determined by transmission electron microscopy with the rate IF deformation of a metal crystal is a thermally activated process, rate theory can be used as a powerful tool in the study of dislocation mechanisms. seeger1 develops the following expression for plastic deformation governed by a single thermally-activated theory results suggests thai formation of lattice vacancies at jogs in screw dislocations is responsible for thermally activated deformation of poly crystalline columbium. Single crystals appear to deform by a different mechanism. Work hardening in fully recrystallized fine grain columbium is found to result from simultaneous decrease in activation volume and in the number of mobile dislocations with increasing strain. Work hardening in recovered polycrystals is found to result from decrease in activation volume with strain only. dislocation mechanism. His equation for strain rate is where N is the number of mobile dislocations per unit volume held up at energy barriers, v is the frequency with which the dislocations "try" the energy barriers, b is the Burgers vector, a is the area a dislocation loop sweeps out after overcoming a barrier, V* is the activation volume which will be defined more completely later, and t* is the thermal component of stress equal to (Ta-Ti), where Ta is applied shear stress and Ti is internal stress of the dislocation network17' given by

Jan 1, 1963

By Robert J. Anderson, Charles H. Eldridge

When a metal or alloy is poured into a mold, internal stresses are set up by the cont,raction in volume on passing from the liquid state at the temperature of pouring to the solid state at the ordinary temperature. It is assumed by the writers that all castings are internally stressed. That any casting is internally stressed is shown by its warping or distortion on maturing at the ordinary temperature, by warping or cracking on heating, or by cracking or distortion on machining. In the investigation made by the writers, the internal stresses in cast non-ferrous alloys were studied with a view to examining the effects of heat treatment (i.e., simple anneal) on the release of such stresses. Data have been obtained that show quantitatively that internal stresses can be removed by appropriate heat treatment. The investigation was limited to a study of the effect of heat treatment on stress release in cast rings of the 87:7:5:1 copper-tin-zinc-lead alloy. The writers are indebted to E. G. Fahlman for the method used for inducing stress in cast rings; to M. E. Boyd for microscopic examination and for other aid; and to G. B. Dalrymple for the chemical analyses. General Information While casting stresses have been discussed considerably, they have usually been treated in a general way, and so far as the writers know no measurements of the magnitude of internal stresses in castings have been reported. It has been suggested by many investigators, particularly in the case of steel castings, that castings are internally stressed, and that these stresses can be removed by annealing. In a casting, the internal

Jan 1, 1923

By H. E. N. Stone, B. L. Daniell

This paper examines the cracking behavior on chemical reduction of three types of ore/oxide briquette mixtures. The complex sintering/hardening atmosphere was replaced by 100% oxygen and the blast furnace atmosphere by a 5/95 hydrogedsteam mixture which was used isothermally at 700°C for a constant, arbitrary time. Cracking has been assessed by measurement of reduction expansion or increase in specimen diameter as a result of chemical reduction and a subjective index based on appearance and friability. Oxidized briquettes of iron ore concentrate crack on reduction'-3 in a manner which parallels the degradation of sinter in the Linder test. In the present work, the cracking behavior on chemical reduction of three types of ore/oxide briquette mixture has been studied. Firstly, LD converter fume with additions of silica; secondly, Oxfordshire ore with ferric oxide; thirdly, ferric oxide with separate additions of silica, alumina and lime. Motivation for the first-mentioned experiments lay in the improvement of the fume as furnace feed; for the second, in assessing the tolerance of a finely divided ferric oxide as a base for low melting point additions. The third series provided additional information. In this work, the complex sintering/hardening atmosphere is replaced by 100% oxygen and the blast furnace atmosphere is replaced by a 5/95 hydrogen/ steam mixture used isothermally at 700°C for a constant arbitrary time. The particular reduction conditions were known from previous experience3 to be capable of disclosing any tendency to cracking. Cracking has been assessed by measurement of reduction expansion (i.e., increases in specimen diameter as a result of chemical reduction) and a subjective index based on appearance and friability. Generally

Jan 1, 1970

By H. G. Warren, E. W. Hough

Correlation of interfacial tension of the methane-n-pentane and methane-n-decane systems was made by Hough and Stegemeier by the use of the Weinaug and Katz equation. The methane-n-heptane and ethylene-n-heptane systems were investigated by the authors. Additional systems taken from the literature were the me thane-propane system by Weinaug. and Katz, the methane-n-butane system by Pennington and Hough, and the n- butane -carbon dioxide system by Brauer and Hough. These systems were analyzed by the Weinaug-Katz equation and the Sugden equation on the IBM 1620 11 computer using a regression analysis program. Parachor and exponent values for each component and system were determined. The experimental work was close to the critical point of the light component in the n-butane-carbon dioxide and ethylene-n-heptane systems, between the critical points of the light and heavy components in the methane-n-pentane, methane-n-heptane and methane-n-decane systems, and close to the critical point of the heavy component in the methane-pmpane and methane-n-butane systems. An empirical formula was developed to find a value of the constant B in the Sugden equation for binary hydrocarbon systems from the parachor values of the two components. Interfacial tension for binary hydrocarbon systems was found to be a direct function of liquid-vapor phase density difference in the same manner as a single-component system. DISCUSSION Interfacial tension may be defined as the measure of the specific free surface energy between two phases having different compositions.1 The interfacial tension (IFT) for a binary system may be predicted for any temperature and pressure if the

Jan 1, 1967

By C Gunther

In the examination of an undeveloped prospect a decision must be arrived at from an inspection of the outcrops and the exposures in a few shallow pits. Prospects that are offered for sale rarely expose any important quantity of good ore, work having usually been stopped when the immediate exploration no longer yielded favorable results. It should be borne in mind, furthermore, that a great majority of prospects have been examined many times, and if of conspicuous promise, would have been acquired for development. In most cases the problem for the engineer, therefore, is to discover the traces of a valuable mineralization that has disappeared through solution, or the conditions that indicate the possibility, or probability, of underlying secondary enrichments. The available data being meager, every feature should be the subject of careful study-the condition of the outcrop, the structural relationships, the associations of minerals, the alterations of wall rocks, the chances for underlying enrichments, and so forth, as well as the actual assay value of the material exposed. It is frequently advisable to spend the time and money necessary to have trenches dug at various significant points along a promising outcrop; such exposures, even if the depth attained is slight, often disclose conditions that are not apparent at the actual surface, as for example, the existence of soft minerals and the distribution of the various minerals through the mass of the deposit. Trenches also permit samples to be taken from points that were not accessible during former examinations. Strong, persistent outcrops of uniform width may be taken to indicate the probable size and character of the underlying vein,

Jan 1, 1932

By S. R. Zimmerley, John Gross

A survey of the status of ore dressing in 19231 placed particular stress on the need of research in the crushing and grinding of ore, especially on the need for a method of measuring the surface of the products obtained in crushing and grinding and for fundamental data on the law of crushing, in order that intelligent conclusions may be drawn from actual crushing or grinding experiments. There has been no satisfactory means of determining the surface of crushed products. The results have been judged entirely by the amount of the various sizes produced, based on sieve sizing for particles above 74 microns in size and on microscopic measurement or elutriation for particles below 74 microns, a method which could give only a general idea of what had been accomplished. The fact that the long controversy between the followers of Kick and of Rittinger has resulted in no accepted conclusion is evidence of the need for fundamental data on the crushing law. Some Methods of Measuring Surface of Particles A dissolution method was used by Wolff to measure surfaces of glass powder. A mixture of sodium carbonate and sodium hydroxide was the solvent and the amount of glass dissolved in two hours from the powder was compared with that dissolved from a glass plate.2 Lately Herbert F. Kriege has used the dissolution method in determining surface of calcite and limestone.3 Dr. Geoffrey Martin and his coworkers in England have also used a dissolution method to determine surface on quartz. They compared the amount of quartz dissolved from the sample in one hour by a hydrofluoric acid solution with the amount dissolved from a measured quartz

Jan 1, 1930

By Edmund M. Wise

NATURE has provided us with many metals, but with few really good ones, and frequently the better metals are the rarer. It is to this circumstance that many physical metallurgists, inventors, and just plain experimenters owe their employment, for much of their work is directed, consciously or otherwise, toward the alleviation of some of the more serious shortcomings of the cheaper, less noble, and weaker metals; by alloying, age-hardening, passivating, cladding, plating, and other useful dodges, which sometimes permit the substitution of one of the less gifted metals for one of the really good ones. As a matter of fact, the varied needs of our complex civilization could be quite well met with only five metals, if they were sufficiently abundant, and one of the five would certainly be platinum, the most noble and versatile that nature provides. Many metals are difficult to handle and seem to take pleasure in defying their investigators to find good uses for them, and finally when a use is found it is frequently quite a specific one; in other words, a hole has to be found--or perhaps made-to fit the peg. It is for this reason that a large amount of research must be con- ducted before the more recalcitrant metals become really useful. In platinum, however, we have a metal that inherently possesses so many valuable attributes that it became useful as soon as methods for producing it in massive ductile form were devised, and once its complicated chemical behavior was understood it became principally an aid to research rather than the subject thereof. In recent years, much research has been done to further improve

Jan 1, 1953

By C. H. Mathewson, H. M. Day

The constitution of the system silver-mercury has attracted the attention of many investigators during the last two decades, but since their results are for the most part in poor agreement, there is little need for a review of their individual contributions. It remained for the very careful thermal and microscopic investigation of Murphy1 in 1931 to give the constitutional diagram in its present and unquestioned form, which is shown in Fig. 1. He devised methods for taking cooling curves on alloys under high pressures and for the microscopic observation of alloys which contained liquid mercury as a structural constituent at ordinary temperatures. The compositions of the intermediate phases were confirmed and supplemented through X-ray analyses by Preston2 and Stenbeck.3 According to Murphy, at 2760 C. silver is able to dissolve 44 to 45 weight per cent of mercury, which may increase at lower temperatures to about 50 per cent. Preston concluded that the saturation boundary occurred at 46 ± 2 per cent at 100° C. From the values reported in the literature, these are the only ones that may be accepted as lying even in the right region. Preparation of Alloys The silver used in the present investigation was supplied by the United States Metals Refining Co. through the courtesy of the Committee on Industrial Uses of Silver and, since a complete spectrographic and chemical analysis was furnished, no attempt was made to purify it or to further establish the impurities present. The analyses reported by the company are shown in Table 1. Milligan4 has found that the magnesium content is probably less than 0.0005 per cent.

Jan 1, 1938

By H. M. Day, C. H. Mathewson

The constitution of the system silver-mercury has attracted the attention of many investigators during the last two decades, but since their results are for the most part in poor agreement, there is little need for a review of their individual contributions. It remained for the very careful thermal and microscopic investigation of Murphy1 in 1931 to give the constitutional diagram in its present and unquestioned form, which is shown in Fig. 1. He devised methods for taking cooling curves on alloys under high pressures and for the microscopic observation of alloys which contained liquid mercury as a structural constituent at ordinary temperatures. The compositions of the intermediate phases were confirmed and supplemented through X-ray analyses by Preston2 and Stenbeck.3 According to Murphy, at 2760 C. silver is able to dissolve 44 to 45 weight per cent of mercury, which may increase at lower temperatures to about 50 per cent. Preston concluded that the saturation boundary occurred at 46 ± 2 per cent at 100° C. From the values reported in the literature, these are the only ones that may be accepted as lying even in the right region. Preparation of Alloys The silver used in the present investigation was supplied by the United States Metals Refining Co. through the courtesy of the Committee on Industrial Uses of Silver and, since a complete spectrographic and chemical analysis was furnished, no attempt was made to purify it or to further establish the impurities present. The analyses reported by the company are shown in Table 1. Milligan4 has found that the magnesium content is probably less than 0.0005 per cent.

Jan 1, 1938

By C. Z. Serpan, L. J. Wittenberg

The density of liquid plutonium was determined, by a pycnometm'c technique, from 664 to 788°C and exhibited a temperature dependence, which could be expressed as:. P= C17.63 - 1.52 x 10-"t] +0.04 g per cc where t = OC. These density values compare favorably with the values previously obtained by a technique utilizing Archimedes' principle. The apparatus and method were evaluated when the densities 0.f molten tin and bismuth were measured and found to be in agreement with accepted literature values. PLUTONIUM or an alloy of plutonium in the liquid state has been proposed as a fuel for a fast-breeder type nuclear power plant.' Since knowledge of the liquid density of plutonium is required for the proper design of such a system, this study was undertaken. In addition, the density and volume expansion coefficient of liquid plutonium are of interest for comparison with these same properties of the six allotropic modifications of the solid metal. Comstock and GibneyZ were first to report a value for the density of liquid plutonium. The value for only one temperature, 665"C, was calculated from data obtained by the radiography of the meniscus, Fig. 3. Recently, the density at a series of temperatures has been reported by Knight,3 who obtained his values by using a differential volumeter, and by 01-sen, Sandenaw, and Herrik, who obtained their values from measurements of the loss in weight of a tungsten bob immersed in the liquid. The density of liquid plutonium reported here was determined by a vacuum pycnometer method. In an evacuated system, the tips of calibrated tantalum pycnometers were lowered beneath the liquid sur-

Jan 1, 1962

By W. Robert Power

Dimension stone is considered by many the premium material for beauty and durability in institutional and monumental construction. Nonetheless in the United States it commands an ever decreasing share of the total market. At the beginning of the century dimension stone accounted for more than half the stone produced in the United States, but by 1974 it accounted for little more than 0.2% and the number of producing quarries and finishing plants had greatly reduced. This decrease in use is accounted for in part by competition from cheaper materials, but another factor seems to be the demand by many designers for uniformity and exact repetition of modular units in construction. Even where stone is used in large buildings modem architects want blandness of pattern and uniformity of color in the stone. Because most natural stone contains variations in color and pattern great strain is put on the quarriers to overcome this and produce a uniform product. This results in increased costs, increased waste at the quarries, and consequently increased price in the market. In spite of this, stone is still looked on as the most prestigious of building materials and its aesthetic appeal is born out by the many simulated stone patterns found in synthetic materials. End Use and Specifications The principal uses of dimension stone are in building construction and monuments. Other uses include flagging, curbing, paving, mill-stock slate, roofing slate, laboratory furniture, and refractory brick. Because many of these uses overlap, an orderly classification of dimension stone uses is most difficult. Various classifications have been used by Cumer (1960), Barton (1968), the U.S. Bureau of Mines yearbooks, and the Building Stone Institute (Anon., 1972).

Jan 1, 1975

By H. D. Hoskold

It was not for the purpose of asserting any superior knowledge or authority, but simply of clearing up, in greater detail, some points casually mentioned in Mr. Scott's able paper, that the writer entered, some two years ago, into the discussion which that paper initiated. In such matters there is always room for differences of judgment, as well as for additional data, which may modify or complete the conclusions even of the best authorities. Those who are immersed in the duties of practical administration or work in the field, and who, being remote from the great scientific national libraries, are obliged to rely on their private collections, and to supplement them by their recollections of earlier studies, labor under special disadvantages in such a discussion; and it must be to the scientific and engineering world a matter for gratitude that Mr. Lyman has been willing to give the benefit of his advantages in this respect. Mr. Lyman would, however, doubtless at once disclaim the conclusion that his masterly summary constitutes " the last word " on this subject, and welcome further evidence, comment and criticism, such as the various contributors may continue to offer. This, therefore, is the motive, and must be the excuse, of the introduction by the writer of the following observations. The Miners' Dial.—Many years since, the writer employed a miners' dial, older in type than Fig. 12,* but without any attached spirit-level, made by Thomas Jones, a pupil of the great Ramsden. Jones was one of the old London makers and opticians, and enjoyed great reputation for accuracy in the con-

Jan 1, 1902

By Edward W. Parker

Note.—The material from which this paper has been prepared was collected tor the U. S. Geological Suvey Bulletin, No. 316, Contributions to Economic Geology, 1906, and appears also, though in somewhat more extended form without illustrations, in that publication. Although the briquetting of coals and lignites has been carried on for many years in Europe, and has reached a particularly high state of development in France, Belgium, and Germany, it has made comparatively little progress in the United States. The causes for the backwardness of the United States in this regard are several, and first among them has been the abundant supply of cheap raw fuel with which the manufactured article has to compete. With our millions of acres of coal-productive territory, from which the product can in moat cases be cheaply extracted, it has appeared in many districts more economical to waste the slack or culm, which constitutes a considerable percentage of the product, than to attempt to save it at the additional expense required for briquetting. It is for this reason that the view in all sections -of the anthracite-region of Pennsylvania is marred by the unsightly culm-banks which encumber the ground, and that in some of the bituminous-districts one sees huge piles of unmarketable slack allowed to burn up in order to get rid of them. When the coal is of a coking quality, or when the slack can be used for steaming-purposes, these losses are not sustained, but many thousands of tons of what might be converted into usable fuel have been wasted every year simply because of the increased expense involved in its preparation.

Jan 1, 1908

By F. W. Newhall

DURING the latter part of the year 1931, the Republic mine of the Republic Steel Corporation, at Republic, about 4 miles south of Browns-ville, Pa., was mining coal along four rib or fracture lines. One of these lines, the west butt rib line, was retreating towards a concrete-lined air shaft, 320 ft. deep, which had been sunk in 1911 for ventilation purposes. With the normal rate of mining at that time, it was expected that this rib line would pass the shaft in three or four months and the shaft would then be abandoned and allowed to cave. Realizing the opportunity presented for the study of an unusual case of ground movement, the question of conducting the study was presented by the junior author to the chairman of the Institute's committee on Ground Movement and Subsidence, Mr. George S. Rice, who presented the matter to Mr. G. H. Morse, General Manager of the Northern Mines, Republic Steel Corpora-tion, and he agreed to cooperate with the Bureau of Mines in making the study, the results of which are presented in this paper. Acknowledg-ments are due to Mr. Morse for his full cooperation in this work and to Mr. G. S. Rice and Mr. J. W. Paul, both of the U. S. Bureau of Mines, for their advice and guidance during the course of the work. The authors are indebted to Mr. B. F. Herbert, mining engineer, Northern Coal Mines, Republic Steel Corporation, who assisted in all the surveys, and Mr. W. H. Smith, draftsman, U. S. Bureau of Mines, who prepared all illustrations for publication.

Jan 1, 1934

By F. R. Hensel

THE absorption of oxygen by molten metals is a quick and convincing method to determine the metallurgical characteristics of various types of furnaces.1 The investigation was restricted to the use of coreless induction furnaces. A major variable in induction furnace practice is the frequency and its influence was studied by comparing melts made in a 5000-cycle and a 60-cycle induction furnace respectively.2 The authors are not aware that such a comparative study has been made before and therefore present this paper in the belief that the results will be of general interest. ANALYTICAL METHODS FOR DETERMINATION OF OXYGEN IN NICKEL An analytical procedure for determining NiO by a quick and simple, laboratory method has been worked out in collaboration with Dr. Herty, of the Pittsburgh Station of the Bureau of Mines. It was found that Dr. Herty's aluminum method as used for the. determination of FeO in iron and steel was very suitable for use with nickel if instead of hydrochloric acid a 10 per cent solution of nitric acid is used for bringing the metal into solution. Essentially this method involves deoxidizing the nickel-oxygen alloy with aluminum (2Al + 3NiO = Al203 + 3Ni) and determining the resulting Al203 by a residue analysis. The original oxygen content can then be calculated from the amount of Al-20,. The method as suggested by Dr. Herty3 is referred to in the present paper as method B. A slight modification of method Bled to the application of method A, a description of which is given below according to F. W. Beiter?:3

Jan 1, 1932

By Earl S. Bardwell

The structural relations existing between cuprous oxide and copper were first systematically studied by Heynl; who suggested that a study of the microstructure of refined copper might be substituted for the analytical methods in vogue for determining the oxygen content of copper coming from the refining furnace. Hofman, Green and Yerxa,2 in their paper A Laboratory Study of the Stages in the Refining of Copper, working along the lines suggested by Heyn, showed that a study of the microstructure could be made to yield a correct estimate of the oxygen content of refined copper. In order to determine the oxygen content of the specimen of refined copper under examination a photomicrograph was first made. From the relative areas of copper and eutectic, the percentage of cuprous oxide and the corresponding percentage of oxygen were then readily calculated. It was found that the values for oxygen thus obtained corresponded closely with the analytical results. With the idea of utilizing this method of determining the oxygen content of each charge dipped from the refining furnaces at the Boston & Montana Reduction Plant, the physical testing laboratory was equipped with suitable apparatus for carrying out the work. It may be of interest to describe certain of the methods which have been worked out in this connection and give such data as have been obtained bearing on the effect of the oxygen content of refined copper upon its conductivity. Apparatus.—For the benefit of those who may be unfamiliar with metallographical apparatus and methods and may be interested to know what equipment is required, a few words with regard to the apparatus are in place at this point.

Jan 1, 1914

By J. J. Lillie

Sublevel stoping was first developed in the Michigan iron mines many years ago. Since that time this method, and modifications with long hole drilling, have been used in a number of non-ferrous mines and have been described in various papers and articles. With a few exceptions, the operations where sublevel methods have been applied are producers of large daily tonnages from ore bodies of considerable size. In selecting mining methods for small properties or relatively small detached ore bodies, sublevel methods often have been overlooked. The method has been used successfully in relatively small operations at Copper Canyon, Nevada, and, more recently, in mining small ore bodies at Darwin, Calif. As a result of this experience, we believe that a review of the general procedure, the advantages noted, and the results obtained will be of interest to many operators of relatively small mines. General Description Briefly, sublevel stoping consists of, first, driving sublevel drifts at predetermined vertical intervals through the length of the stope block; second, breaking an initial mining slot across the stope; third, driving crosscut benches from each sublevel by slabbing into the slot; and, fourth, breaking the ground between benches. Applicability Since this is an open stope method, it requires wall rock that will stand over reasonable stope lengths without caving or excessive slabbing. Ore must be moderately firm but need not be hard. The method is best adapted to steep dipping, tabular or lenticular ore bodies but may be applied to ore bodies of almost any shape if their vertical extent is appreciable. It can be used with dips that are too flat for successful shrinkage stopes and can be modified for use with slushers on dips below about 40". Initial mining at the Copper Canyon operation consisted of sublevel stopes for the wider ore sections and shrinkage stopes for the narrow sections where ore widths averaged about 15 ft. After some experience and a study of comparative results on completed stope blocks, sublevels were substituted for shrinkage stopes even in the narrow ore widths. Practical stope lengths depend upon the character of the walls and the continuity of values within the ore body. Where blocks of low grade or waste are included in the stoping limits, these areas can readily be left as pillars for intermediate wall support and longer stope lengths may be planned. Raises can be spotted in narrow or low grade areas and stope lengths adjusted accordingly. Stoping Details To illustrate stoping details, assume that we have an ore shoot 15 to 30 ft wide and about 200 ft long, with walls that would stand over a stope length of 80 to 90 ft (Fig1). PRELIMINARY DEVELOPMENT Preliminary development for sublevel stoping would be simple. A service raise is driven at about the center of the block and stope limits planned to leave a pillar around this raise. Sublevel drifts driven each way from this central raise will outline the

Jan 1, 1950

By John M. Sharp

John M. Sharp, Jr. (Assistant Professor of Geology, University of Missouri, Columbia, Mo.)-Geothermal gradient and surface temperature data anomalies are potentially useful tools in mineral exploration, These data, however, may reflect a number of geologic and hydrologic processes as well as the thermophysical properties of the geologic materials. The author presents a relatively simple model which may be of value in mineral exploration. The lack of consideration of other processes, however, limits its usefulness. For instance, because of erosion or sediment deposition over geologic time the land surface must be considered a moving boundary in such a model. Evaluation of this effect coupled with annual surface temperature and thermal conductivity variations can result in temperature profiles such as shown in [Figs. 4 to 7]. These effects and others, such as ground-water movement," must be considered and filtered from the data before proper interpretation is possible. Another assumption which should have been discussed is, why were the observed mean surface temperatures not used for extrapolation of the gradients in [Figs. 4, 6, and 7?] Conductive heat transport responds to the actual boundary (land surface) temperature, not to theoretical temperatures in the absence of perturbations. Benfield presents a theoretical model for calculating perturbations in the geothermal gradient for erosion and sedimentation. The temperature (T) at any time (t) and any depth below the surface (x) is given by [ ] where T is the mean surface temperature, G, the geothermal gradient, v, the rate of erosion (or sedimentation),[ ], the long-term rate of change of T0, and k is the thermal diffusivity of the rock. Using the author's values and a rate of erosion of 1.54 cm per yr for a period of 10,000 yr, a thermal profile as shown in [Fig. 10] will be generated. A thermal diffusivity of 0.0164 sq cm per sec was used, corresponding to a thermal conductivity of 0.0082 cal per cm per sec per C. In [Fig. 11], a sediment deposition rate of 3.0 cm per yr for a period of 1000 yr was used to generate the subsurface temperature profile. A surface temperature of 24.3°C was used, as specified in [Fig. 9, 7], was set equal to zero for both cases. Superposition on the generated profiles in [Figs. 10 and 11] of the annual surface temperature variation perturbation (which may be calculated in a number of ways) will yield profiles similar to those in [Figs. 4 and 7]. Similar profiles can also be produced by regional ground-water flow. Models like the author's can be of value in mineral exploration. Other processes, however, which affect surface temperatures and gradients must first be considered, calculated, and filtered from the data if anything but the crudest qualitative interpretation is to be made. Robert C. Edmiston (Author's reply)-Professor Sharp has raised three objections to my interpretation of the subsurface temperature data I collected at Silver Bell. These are: 1) No correction was made for erosion or sedimentation,

Jan 1, 1977

By Takeyasu Ito, Mayumi Someno, Kazuhiro Goto

SINCE the pioneering work by Kiukkola and Wagner,1 many experiments have been reported on solid electrochemistry at elevated temperatures. However, the studies have been confined to experiments under isothermal conditions. One may conceive many situations under nonisothermal conditions. With two different temperatures T1, and T2 at the two electrodes, the electromotive force, E of a Galvanic cell will be expressed by the following equation under a steady state heat transfer in solid electrolytes of zirconia-lime and thoria-lime. E = ^ $ l&-dGO2+a(T2-Ti) [1] where tO2- is the transference number of oxygen ions in the electrolyte, Go, is the chemical potential of oxygen, and a is the coefficient of the thermoelec-tromotive force due to the temperature difference. The objective of the present study was to evaluate the coefficient of the thermoelectromotive force for zirconia-lime and thoria-lime under isobaric condition. The physical meaning of this coefficient is out of the scope of the present communication. The experimental cell assembly is schematically shown in Fig. 1. The zirconia-lime electrolyte tube and thoria-lime electrolyte tube were 8.0 mm OD and 5.0 ID, from commercial sources with chemical analyses of 94.8 wt pct ZrO2, 3.85 pct CaO, 0.83 pct SiO2, 0.25 pct TiO2, and 0.05 pct Fe2O3; and 95.0 pct ThO2, 4.0 pct CaO and rare earth metal oxides, respectively. The specific gravity was 5.5 g per cu cm for zirconia-lime and 9.8 g per cu cm for thoria-lime. Original powder size before shaping and sintering the tube was several microns for both electrolytes. The distance separating the two electrodes was 4.0 or 5.0 cm. Platinum wire of 0.5 mm diam was used for the electrodes. The temperature gradient was controlled by heating one electrode with a small heating coil of nichrome wire. The temperatures at the two electrodes were measured with two calibrated Pt-13 pct Rh:Pt thermocouples, directly contacting the two platinum electrodes. The atmosphere was either air or pure oxygen. The partial pressure of oxygen in air was considered equal at the vicinities of the two electrodes, with negligibly small thermal segregation in the gas phase. The difference of the chemical potential of oxygen was controlled only by the temperature difference at the two electrodes and not by the oxygen pressure difference. The temperature ranges were 600" to 1200°C for zirconia-lime and 850" to 1200°C for thoria-lime electrolytes. Fig. 2 shows the relation of the measured electromotive force and the difference of the oxygen chemical potential at the two electrodes for zirconia-lime and thoria-lime electrolytes. The electromotive forces in the figure were measured by a *0.05 mv potentiometer. The chemical potential difference was calculated by the following equations.'

Jan 1, 1970

By F. J. Fayers, S. A. Hovanessian

The one-dimensional displacement equation for a homogeneous porous medium, including the effects of gravity and capillaty forces, has been solved by a numerical method. A finite-difference scheme is developed for obtaining saturation, pressure and fractional flow profiles in waterflood recovety problems. From the numerical examples given, it is concluded that the gravitational forces have a pronounced effect on the saturation profiles and the pressure distribution curves of the system. INTRODUCTION Within the past 20 years, a number of papers have appeared in the literature dealing with the quantitative treatment of waterflood recovery problems. In their celebrated paper, Buckley and Leverett1 described a method for calculating saturation profiles when the effects of capillary pressure and gravity are excluded. Terwilliger, et al,2 included the effect of gravity in their theoretical and experimental investigation of oil recovery problems and obtained close correlation between experiment and theory. welge3 described a simplified method for obtaining the average saturation and the oil recovery from an oil reservoir. The effect of gravity can be included in this calculation. More recently (1958) Douglas, et al,4 presented a method for calculating saturation profiles which includes the effect of capillary pressure. The authors start with the one-dimensional displacement equation (which is nonlinear in the derivative) and, by a change of variable, transform this equation to a semi-linear partial differential equation. This equation is then solved by a finite-difference method on a high-speed digital computer. Fayers and Sheldon5 obtained the solution of the one-dimensional displacement equation by directly replacing the differential equation by a finite-difference equation. The effects of capillary pressure and gravity were in- cluded in their solution. Here, since the movement of the foot of the saturation front is governed by a separate equation, the elapsed time in attaining a particular saturation profile cannot be obtained. The results of these two papers indicate that the inclusion of capillary forces eliminates the triple-valued Buckley-Leverett saturation profiles. In the present paper, the one-dimensional displacement equation for a homogeneous permeable medium, including the effects of capillary and gravity forces, is solved. The method of solution resembles that described in the paper by Douglas, et al, since it involves a similar transformation of variable. However, it extends their work in that the effect of gravity is included and, in addition, pressure profiles may be calculated. Also, the functions of saturation [kro(S), krw(S) and Pc (S) ] required are entered in tabular form rather than as low-order polynomials. This simplifies data preparation and permits the use of a greater range of function types. Unlike the method of Fayers and Sheldon, the corresponding elapsed time required for the development of each saturation profile is calculated and, also, saturation profiles may be calculated after breakthrough. THEORETICAL CONSIDERATIONS The dimensionless form of the one-dimensional displacement equation for a homogeneous porous medium as obtained from Darcy's law and material balance relations can be written as follows.