Search Documents

By -1ng. B. Stampa

Introduction The author investigates the technology available for mine flow reversibility by reversing the operation of the main fans. Air bypassing, reversed sense of impeller rotation, and blade angle overturning are indentified as the most important means of achieving the flow reversibility. The axial flow fan is studied in some detail and the important variables of fan capacity, pressure, and efficiency are compared. Although some references to rotor velocity vectors are made (Fig. 1) the subject is not presented in detail in order to stay within the paper's intent. Background Where applicable, the requirements of mine air reversibility are an important part of the overall mining operation and should be given proper attention during mine ventilation design. The need for preventing mine fires in intake shafts is the reason that, for a long time, it has been a requirement in the Eastern European countries to have the feature of flow reversibility built into all main mine ventilators. In West German coal mines, this requirement does not apply since higher priority is given to safety precautions. Some metal and mineral mines in the United States are required to have ventilation currents readily reversible in order to fight underground fires as stipulated by the Title 30, Mineral Resources, and by the mining laws of some states. From an equipment performance standpoint, assuming the validity of other flow technical data, the question of the ventilator flow reversibility is of ten related to the actual scenario of the begining of an emergency. Most of the time, the system operates within half of the design capacity only and assuming that the equivalent mine orifice is stable only a quarter of the design pressure must be produced by the fan in any event. For such an operating point, the effective gradient and energy losses can be disregarded since fire emergencies usually last for only a short period of time. Equipment Comparison Fig. 2 depicts a ventilation arrangement wherein the flow can be reversed through changing the functional position of the dampers (slideplate or blade type). Both axial or radial fans can be applied in this case. For the mine exhaust operation, slide plates (guillotines) I and I11 are opened while plates I1 and IV are closed. The flow thus encounters two reroutings, which due to the reverse ventilation flow cannot be equipped with proper sheet metal deflectors, and therefore large pressure losses result during the air reroute operation. When the intake operation is considered, the dampers I and I11 are closed and the pair I1 and IV is opened. For this arrangement, almost the same flow conditions exist as for the foregoing exhaust mode; however, one additional corner must be applied. Even if a highly efficient ventilator is used in one of the previously described systems, the additional pressure losses resulting from air rerouting plus those encountered between the planes "0" and "00" significantly affect the overall energy requirements. Illustrated in Table 1 are the relative component losses of even flows for evaluation of various detour arrangements. From the aerodynamics standpoint, when these components are being designed, serious consideration must be given to the individual levels of the pressure loss coefficient, 5. Should there be an increase in the sum of the loss coefficients due to the particular component selection such that, for example, the net change is 1.2; the resulting pressure to be produced by the fan can be calculated from:

Jan 1, 1981

By Kenneth A. Moon

Kenneth A. Moon (U.S. Army Materials Research Agency)—The authors are to be congratulated for a very interesting and valuable paper. Their discussion of the structural implications of the results shown in their Fig. 5, however, requires a small correction. The model of Speiser and Spretnak with 0 = 1 and z' = 2 is perfectly reasonable for the Ti-O a phase, but Eq. [3] is valid only for solutions sufficiently dilute that the number of empty sites excluded by more than one filled site is negligible. The composition at which intrinsic saturation occurs therefore cannot be deduced from Eq. [3], but but must be decided by consideration of the structural details of the phase in question. In this case, intrinsic saturation is expected not at the composition Ti3O but at Ti2O, because Ti2O has the anti-Cd structurel4 for which each filled octahedral site has two nearby empty sites, one in the hexagonal plane immediately above it, and one in the similar plane below it. The other two models, with ?=1/3 and 1/2, imply a distinction between octahedral sites in pure titanium which is not easy to justify. The problem of extending Speiser's and Spretnak's treatment in a general way to more concentrated solutions will be the subject of a forthcoming publication by the writer. M. T. Hepworth and R. Schuhmann, Jr. (authors' reply)—The authors wish to thank Dr. Moon for calling to their attention the paper by Holmberg which presents the results of X-ray studies of Ti-O solutions ranging from 0 to 33 at. pct 0 and quenched from various annealing temperatures between 400" and 1800°C. Within these ranges, Holmberg found three types of phases: 1) At high oxygen contents (above 25 at. pct) and low annealing temperatures, he found the anti-Cd(OH)2 structure referred to by Dr. Moon. In this structure each titanium atom is in contact with 3 oxygens and each oxygen is in contact with 6 titaniums, the "available" oxygen sites corresponding to every other layer of octahedral sites in the titanium matrix. The limiting composition is Ti2O. However, this anti-Cd(OH)2 structure was not observed for samples containing 25 at. pct 0 or less. 2) For the specimen containing 25 at. pct 0 annealed at 400°C an ordered Ti3O structure was observed. This structure is related to the anti-Cd(OH)2 structure but differs from it by providing only two oxygens adjacent to each titanium atom and thus is consistent with the model represented by Eq. [5] in our paper, with 6 = 1/3, z' = 0. 3) For dilute solutions and for more concentrated solutions annealed at higher temperatures, the structure corresponds to that of the metal with random distribution of oxygens among all the octahedral sites. Thus, it is interesting to observe that the thermo-dynamic indications of ordering in the vicinity of Ti3O can now be supported qualitatively at least by Holmberg's X-ray evidence of the existence of an ordered phase of the composition Ti3O. That is, for solutions with oxygen contents close to that of Ti3O, both the thermodynamic data and the X-ray data are more consistent with models based on the ordered structure of Ti3O than they are with the model which Dr. Moon suggests corresponding to "intrinsic saturation" at Ti2O.

Jan 1, 1963

By M. A. Dayananda

Based on the Kirkendall frame of reference, a method is proposed for the determination of atomic mobilities of all the diffusing species in a multicorn-ponent system with a single diffusion couple. The method is based on an atomic mobility model developed on the concept of negligible interactions among the intrinsic fluxes. It is shown in the model that mobilities can be obtained directly from the cumulative intrinsic fluxes past the Kirkendall interface. The proposed method replaces the need for a prior determination of interdiffusion coefficients far the calculation of mobilities. Relations between intrinsic diffusion coefficients and mobilities are derived and the mobility calculations are illustrated with diffusion data in Cu-Zn-Mn alloys at 850°C. ThE concept of "intrinsic flux" with respect to a fixed lattice was introduced "i Darken1 to explain toa Kirkendall effect2 demonstrated by the motion of inert markers during isothermal diffusion in single-phase binary solid solutions. Based on this concept, intrinsic diffusion studies have been made in various binary metallic systems3,4 employing such a lattice frame of reference, commonly referred to as the Kirkendall interface. Similar approaches, both theoretical and experimental, have been presented5"10 to study intrinsic diffusion in multicomponent systems. Based on the direct integration of Fick's law extended to multicomponent diffusion, Philibert and Guy8 proposed a method for the determination of intrinsic diffusion coefficients. For an n-component system, this procedure requires an experimental study with (n — 1) diffusion couples, all having their Kirkendall interfaces at the same compositio;, where n(n — 1) intrinsic diffusion coefficients are defined. This technique has been employed for ternary diffusion studies by Dayananda and Grace" and Guy and Leroy.11 A different approach is recommended by Ziebold and Cooper,12 who have derived relations between interdiffusion coefficients and atomic mobilities employing fluxes referred to the local center of volume. Their analysis is based on the simplifying assumption of negligible interactions among intrinsic fluxes. This assumption has been considered satisfactory for dilute solutions.5"7 The use of this analysis for the calculation of mobilities requires an initial determination of interdiffusion coefficients with a set of diffusion couples having intersecting diffusion paths. It is the purpose of this paper to propose a method that would permit a direct determination of mobilities of all components of a multicomponent system from a single diffusion couple. This method is based on a mo- bility model developed with diffusion fluxes referred directly to the Kirkendall interface, generally identified by inert markers. gen erall, like that of Ziebold and Cooper,12 employs the simplifying assumption that the flux of each component relative to a fixed lattice is caused only by the driving force of its own chemical potential gradient. THE KIRKENDALL INTERFACE Inert markers are employed in diffusion couples to locate experimentally the position of the Kirkendall interface. They are initially placed at the weld interface for "sandwich" couples, or at the original vapor-solid interface for vapor-solid couples. Studies of marker motion in binary systems3'4 with both types of couples indicate that markers remain in a plane of constant composition and move with this plane para-bolically with time. Parabolic marker movements were also observed in ternary Cu-Zn-Mn couples by Dayananda and Grace.10 It is reasonable to expect a similar marker behavior even for diffusion couples with a higher number of components.

Jan 1, 1969

By Clarence W. Dunham

BECAUSE of the earthquakes that occur at Chuquicamata, the design of the smelter stacks constituted the most difficult structural problem of the entire sulphide ore project. Slight tremors occur almost daily and shocks of moderate magnitude are not uncommon. Naturally, the operation of the smelter depends upon the safety of these stacks, and their resistance to earthquakes was the critical feature of their design. Adequate data of the magnitudes of past shocks at Chuquicamata were not available. However, considering the information that was obtained from experiences in other parts of Chile, a period of one to two seconds was adopted as a basis for the design. To complicate the problem further, the stacks had to provide for operations under a wide variety of conditions ranging from the possibility of running one reverberatory furnace and two converters initially to perhaps five or six furnaces and eight or ten converters simultaneously in the completed plant. No one could tell for certain just what the ultimate capacity might have to be because the plans permitted a large extension beyond the first installation if this became necessary. Studies of the stacks were made for many conditions. At first it was thought that one stack 600 or 650 ft high should be used initially for both the furnaces and converters, with a second similar stack to be built for the future extension. This height would provide adequate draft in the rarified atmosphere at the plant's elevation of 10,000 ft. It would also disperse the gases high in the air. Preliminary studies of this large stack showed that such a structure was possible if made of steel but it would be exceedingly costly. Furthermore, the effects of the tendency for the top to whip under the action of earthquakes might be serious, and the design had to be based upon assumptions which might not be trustworthy. Such a tall stack was finally abandoned in favor of a larger number of smaller ones. Initially, one stack will service the first three or four furnaces. Another will handle the gases from four or five converters. The smelter has been located in such a position that the prevailing winds carry the fumes away from the remainder of the plant. A height of 300 ft for the stacks was finally selected. The top diameter is approximately 24 ft 9 in. clear inside of the lining. The converter stack is located upon a hill alongside the smelter. This provides an effective increase in height because its base is approximately 66 ft above the yard level. The base of the reverberatory stack is at the latter elevation. Stacks made of reinforced concrete or of steel were investigated, and so were many shapes for them. As these studies progressed, the lightness of a steel structure, and the ductility of the metal itself, led to the decision to use steel for the main part of the stacks. The fact that serious damage to one of the stacks would cause the plant to shut down, caused special studies to be made of the stress conditions that might exist around the breeching which had to be nearly 15 ft wide and 40 ft or more high where it joined the stack. This height was necessary in order to provide adequate transition from the horizontal flow of the gases to the vertical direction without undue eddies. This opening constituted a serious source of weakness in the structure. If made with sufficiently strong reinforcement around its edges, there would be a hard spot in the structure that might cause trouble because of shaft vibrations.

Jan 1, 1952

By J. S. Kasper, R. M. Waterstrat, B. F. Decker

THE existence of v phase in the Mn-Mo system was discovered in this laboratory several years ago,' but neither the conditions of its formation nor its composition were known, and preliminary attempts to reproduce the phase were unsuccessful. We wish now to specify the information appropriate to phase formation on the basis of experiments performed since that time. The starting materials were in every case electrolytic manganese and high purity molybdenum. Two methods of preparation were employed: l—arc-melting varying combinations of the elements in an inert atmosphere and subsequent heat treating, and 2—sintering compressed mixtures of finely divided powders of the elements. In the latter method, the powders were first passed through 200 mesh screen and then compressed into cylinders of % in. diameter and % in. length, which were sintered at elevated temperatures in an atmosphere of dry hydrogen. For some samples, the sintering temperature was 1200°C (for 1 hr), and these were then heat- treated at lower temperatures for times up to 24 hr. Eventually it was found, for the proper composition, that essentially pure a phase could be produced by sintering at 1125°C for 3 hr. Quenching to room temperature was effected by means of a stream of cold, dry hydrogen in a water-cooled chamber. The arc-melting procedure was found to be unsatisfactory after an investigation of many samples at different compositions and temperatures. Large quantities of manganese were vaporized during melting and none of the products were homogeneous or contained extended regions of pure phase. Nonetheless, these experiments established that no formation occurs in the Mn-Mo system below 1115oC, and indicated, at least roughly, the composition range of interest for further exploration. The more definite results obtained from samples produced by the second method are given in Table I. A portion of sample 2 heated for 16 hr at 1000°C in a Vycor tube transformed to molybdenum plus unidentified phases of complex X-ray pattern. From these few results it appears that the region of phase is quite narrow in composition. It is of interest that the composition is such as to make for difficulties in correlating this structure on an electron atom basis with other a structures of iron, cobalt, and nickel. In that respect Mn-Mo shows the same anomaly as Mn-Cr and Mn-V systems.' A second feature is that in common with the two other known molybdenum (Fe-Mo and Co-Mo), Mn-Mo v exists only at elevated temperatures. The X-ray powder pattern of the pure a phase of Mn-Mo is given in Table 11. It agrees well with the patterns established for other structures, especially with that for Fe-Mo as given by Goldschmidt.An attempt is being made to establish whether an ordering of the respective atoms occurs and such information will be reported in a future publication. Acknowledgment The authors acknowledge gratefully the assistance of Mrs. J. R. Belanger in some portions of this work. References 'J. S. Kasper, B. F. Decker, and J. R. Belanger: Journal of Applied Physics (1951) 22, p. 361. 2 A. H. Sully: Journal Inst. Metals (1951) 80, p. 173. H. J. Goldschmidt: Research (1949) 2, p. 343.

Jan 1, 1954

INTRODUCTION Besides the European export credit agencies covered in Ted Rides' paper in this Chapter, other agencies are also active (see Appendix) but the most notable for mining projects are The Export-Import Bank of the United States ("US Exim") and the Export Development Corporation ("EDC") of Canada. Mexico's Fomex is basically a short-term trade-finance fund administered by the Central Bank. US Exim This independent agency can provide loans, guarantees, and insurance. Like all export-credit agencies, its mandate is to support the export of goods and services from the US as a means of competing against other countries' products. If a piece of mining equipment can only he made in the US, the US Exim may very well not provide any financial assistance. (It is important not to place the order for any item for which export credit is sought because, once ordered, the situation is no longer competitive in US Exim's eyes.) Direct Credits and financial guarantees ("buyer credits") are commonly in amounts greater than 85 million and for terms longer than six years. An example here is the $48.5 million provided to PT International Nickel Indonesia (see Robert de Gavre's paper in Chapter 12). US Exim usually requires a 15% downpayment and, therefore, finances up to 857 of the goods; less if the US content is lower. The dollar funding can he US prime, London Interbank Offered Rate (LIBOR), or other sources. Exim can fund in either or both of the following ways: 1. Under a US bank Letter of Credit ("L/C") 2. Reimbursement to the buyer/borrower via a US bank account. US Exim will, without charge, issue a preliminary commitment. It will, however, need to approve the various credit agreements and prefers to tie other parallel financings into one loan agreement. US Exim's total commitments are large, up to $5R billion in aggregate under various programs. US Exim has been the world's leader in medium-to long-term minerals project financings/ co-financings but suffers from (i) aggressive foreign export-credit competition whereby other nations mix in soft-loans or aid programs ("mixed credits") to increase the percentage financed and lower the interest margin and (ii) an imbalance in its own cost of funds. A common US Exim package would be as follows: 15% Banks under US Exim guarantee, floating rate over prime or LIBOR. 35% US Exim funding, fixed rate 35% Pefco funding, fixed rate 857 Drawn down pro-rata under US bank L/C 15% Cash down payment (may have been financed within a project/corporate credit) 100% Repayment usually begins six months after planned start-up in equal semi-annual instalments, with the banks usually paid out first, Pefco next, and US Exim last. Medium-term credits ("supplier credits") are issued for US equipment exports for terms up to five years, again for 85% of the equipment costs although the exporter is expected to bear at least 10% out of that 857 for its own risk. The buyer is required to be a first-class credit such as some governments or highly credit-worthy companies. Otherwise a bank L/C would be required. (This may be wrapped into an overall project-finance package for a minerals development. The project-finance banks provide an L/C to US Exim instead of funding that portion themselves.) US Exim guarantees 100% of the political risk and either 85% or 95% of the commercial risk for

Jan 1, 1985

By P. E. Baker

Approximate solutions are presented for the heat-flow equations in a loss-free linear system with a moving source and with heat transfer by convection and conduction, representing in situ combustion in an oil reservoir. The rate of heat generation and the velocity vf of the source (flame front) are assumed constant. A cold front or convection front caused by the cooling effect of in-jected air develops behind the flame front and moves with velocity vc, which is determined by the thermal properties of the air and rock. Because of thermal conduction the fronts are not sharp; i.e., they do not represent temperature discontinuities. The following solutions apply after a sufficiently long time. where Q is heat generated per unit volume of formation, k is thermal conductivity, CF is volumetric heat capacity, a is thermal diffusivity, and subscripts 1 and 2 refer to values behind and ahead of the flame front, respectively. The parameter CF2 is contained in v . Te is initial reservoir temper- . C2 e ature and air-injection temperature. Other mathematically possible solutions are presented. The different solutions result from the use of different values for various physical parameters. The solution just presented is thought to be most commonly applicable. INTRODUCTION In this paper, approximate analytical expressions are derived for the temperature profile developed in the underground combustion method of oil recovery. A qualitative description of the process may be found in a paper by Tadema.1 The flame front is regarded as a moving source with a constant rate of heat generation. Heat transfer is by conduction and convection. Previous publications, of which a few are cited here, 2-5 have also attacked this problem and have presented solutions pertaining to different methods of approximating or idealizing the process studied. The present paper also treats an idealized case: linear flow is assumed for heat and fluids, and vaporization and condensation effects are neglected. The results obtained are similar to those derived by Bailey and Larkin,3 but are obtained by an entirely different procedure. The method used here should give considerably greater insight into the physics of the in situ combustion process. Four types of cases are considered, distinguished by thermal and fluid-flow properties of the system. A constant rate of heat generation and constant rate of flame-front advance are assumed. Flame-front temperature is determined for each case using a heat balance which involves the entire temperature profile. The applicability of the different solutions to real systems is discussed after they are all presented. Again, this is done for the purpose of understanding better the physics of the process. Consideration of the nonapplicable solutions and of the reasons for their not applying is significant. In a paper by Cooperman,4 the only case solved is one considered here as not applicable. Fluid flow, as such (pressures, saturations, oil recovery, etc.), is not treated. This subject has been covered in a paper by Wilson, et al.6 Also, we are not concerned with requirements for continuance of the process; we only attempt to determine the temperature history for cases where the process has continued for some time. PHYSICAL SYSTEM AND APPROACH TO PROBLEM A linear flow (heat and fluid) system is assumed and the x-axis is taken parallel to the flow direction. The combustion zone (flame front) is vertical,

By C. D. Stahl, E. E. Templeton, R. F. Nielsen

It has been customary, in predicting saturation changes, to use the Leverett fractional flow formula", obtained by eliminating the unknown pressure gradient from the generalized Darcy equations for the separate phases. The formula presents difficulties in the case of counterflow, since the "fractional" flow may be negative, greater than unity, or, in the case of a closed system, infinite. Recently, it has been shown by several authors that the corresponding equations (with capillary pressure and gravity terms) for actual flow of the phase may be used just as well. These equations are in agreement with Pirson's1 statement that, if the two mobilities differ considerably from each other in a closed system, the flow is largely governed by the lower value. The present study was undertaken because of an apparent lack of experimental data on gravity counter-/low with which to test the theory. A 4-ft sand-packed tube in a vertical position was employed. Electrodes for determining saturations by resistivity were spaced along the tube, one phase being always an aqueous salt solution. Air, heptane, naphtha, or Bradford crude oil was used for the other phase. A reasonably uniform initial saturation was set up by pumping the phases through the system, alter which the tube was shut in and saturation profiles obtained at definite intervals. Cumulative flows over certain horizontal levels were obtained by integration of the distributions; hence, differentiation of the cumulative flows with respect to time gave instantaneous flow rates. To compare experimental and theoretical flow values, capillary pressures were assumed given by the final saturation-distribution curve. The upper part corresponds to the "drainage" region and the lower part to the "imbibition" region, where trapping of the nonwetting phase occurred. While calculations indicated that the capillary pressure saturation function and, probably, the relative permeability saturation functions changed during the segregation, the relation of the measured rates to saturation distributions are in general accord with the frontal-advance equation. It appears that the Darcy equations, as modified for the separate phases, are generally valid for counterflow due to density differences. The usual method of predicting saturation changes, which involves a continuity equation and the elimination of the unknown pressure gradient from the flow equations, should therefore be applicable. However, the need for advance knowledge of drainage and and imbibition "capillary pressures" and relative permeabilities during various stages presents difficulties. INTRODUCTION The present study was undertaken because of a seeming lack of experimental data relating to vertical counterflow of fluids of different densities in porous media. In particular, it was desired to determine whether data obtained from these laboratory tests were in accordance with certain mathematical treatments of counterflow which have been proposed. The gravity "correction" has been incorporated into the flow equations (and, hence, into displacement theory) nearly as long as both have been used. field4 and laboratory5 data have generally borne out the validity of the theory as applied, for instance, to downward displacement by gas, with all fluids moving downward. However, the modifications for counterflow have only recently been pointed out. 2-3 It has been customary to use fractional flow rates instead of actual flow rates in displacement calcuIations. In the case of counterflow, this results in negative values, values greater than unity and, when rates are equal and opposite, in infinite values. As pointed out by Sheldon, et a1,3 and by Fayers and sheldon,2 actual flow rates may be used just as well. The fact that these may be of opposite signs for the two fluids does not present any difficulty.

By A. P. Young, F. C. Holden

IN many of the early investigations of the aging of titanium alloys, it was observed that the retained beta phase could be aged to a high hardness without an apparent change in microstructure; moreover, in some alloys it was found that even a very rapid quench produced beta having an anomalously high hardness. What appeared to be hard beta phase was designated as "beta prime," to distinguish it from the softer normal retained beta phase. Frost and co-workers'.' demonstrated that the increased hardness is caused by the formation of a metastable phase, omega, which can be identified from its X-ray diffraction pattern. This reaction also has been studied by Brotzen, et a1.,3 and the structure of the omega phase has been published by Silcock, et al.," and by Austin and Doig.3 The X-ray diffraction analysis by Austin and Doig indicated that omega is low in alloy content, approaching the composition of the stable alpha. The aging process proceeds by the path Thus, overaging results in the formation of alpha and the ultimate disappearance of omega. This is accompanied by a decrease in hardness and a recovery of ductility. The present work represents a study of the aging process in a high-purity Ti-6.4 Mn alloy, in which optical and electron microscopy, X-ray diffraction, and hardness data were correlated. The specimens, 1/8-in. sections cut from 1/4-in.-diam rod, were heated in argon to a temperature just into the beta field (810°C), held for 1 hr, and water-quenched. The aging samples were heated in air for 1 hr at 300 to 500°C. The specimens were ground and mechanically polished, finishing with alternate etching and polishing on a slow-speed wheel to remove disturbed metal from the surface. The surface finally was swab-etched, rinsed with tap water, and air-dried. The etchant used was an aqueous solution containing 1 1/2 pct HF and 3 1/2 pct HNO3. This procedure is identical with that used for preparing metallographic specimens, except that the optimum degree of final etching required for electron microscopy may vary from that used for light microscopy. Metal replicas, backed with silica, were prepared from plastic strip-pings for examination with the electron microscope. Complete details of the procedures used for preparing these replicas are available elsewhere." Fig. 1 shows a comparison between the structures revealed by the electron microscope and those obtained by conventional light microscopy. Hardness and X-ray diffraction data are listed in Table I. No evidence of a second phase is apparent in the optical micrographs for the as-quenched sample, or for the specimens aged at 300 or 400°C; fine alpha particles can be seen in the specimen aged at 500°C. In the electron micrographs, visible equiaxed pocks appear in the as-quenched specimen, and, with increasing density, in the samples aged at 300 and 400°C. After aging at 500°C, the structure becomes markedly coarser and develops an oriented appearance of a second phase, coincident with the appearance of visible alpha particles in the light micrographs. These observations are confirmed by X-ray diffraction and hardness data. In these specimens, aged for 1 hr, the intensity of the omega pattern increases to a maximum at the 400°C aging temperature, corresponding to maximum hardness and the maximum density of pocks in the electron micrographs. At this point the beta phase shows a definite enrichment in Mn. At 500°C, little or no omega re-

Jan 1, 1959

By C. M. Wayman, G. R. Srinivasan

A metallographic study of the isothermal products formed between 750° and 285°C was made in an Fe-7.9 wt pct Cr-1.11 wt pct C alloy, and a time-temperature-transformation diagram was determined. The study shows that the austenite decomposes into three different products: pearlite above 540°C, ferrite and carbide between 540° and 300°C, and lenticular bainite below 300°C. No upper bainite forms in this alloy. The results are discussed in terms of carbon diffusion models for upper bainite formation. AUSTENITE transforms into several products depending on the temperature, composition, and rate of cooling, and the various transformation products have been a source of controversy for a long time. Since the classical study of Davenport and ~ain' extensive work has been carried out. The present study concerns the isothermal transformations in an alloy which was used for a detailed investigation of bainite crystallography and provides information supplementary to the work of Lyman and Troiano who studied austenite decomposition in steels containing 1 pct C and varying amounts of chromium. Their work showed that increasing the amount of chromium in high-carbon steels had the effect of depressing the B, temperature and of shifting the TTT curves to longer times and lower temperatures. They further found that if the chromium content is increased in a 1 pct steel to about 9 pct no bainite would form even after a period of 100 days. However, a preliminary investigation by the present authors showed that bainite plates do form in steels containing about 8 pct Cr and 1 pct C. In view of this and some results from a thin-foil electron microscope investigation of the bainite formed in the present alloy: it was considered desirable to investigate the other isothermal products as well. EXPERIMENTAL PROCEDURE The alloy used in the present investigation was obtained from a triply vacuum-melted ingot prepared from high-purity materials. Chemical analysis for the alloy verified the composition to be Fe-7.9 wt pct Cr-1.11 wt pct C. Metallographic observations were made on i by i by « in. specimens which were aus-tenitized at 12 50°C for 50 to 60 hr in evacuated quartz capsules and then water-quenched. Since the M, temperature for this alloy is below room temperature, the homogenizing treatment produced a completely austenitic structure consisting of very coarse austenite grains (ASTM #0-1). Several samples of the austenitized specimens were metallographically prepared and observed for any proeutectoid carbide separation. It was found that all the carbon was in solution. The water-quenched specimens were upquenched and given isothermal treatments at temperatures between 285" and 750°C for varying periods in molten salt or lead baths. The specimens were then water-quenched, and those showing less than 5 pct transformation were used for plotting the beginning of the austenite decomposition. To ensure the removal of the disturbed layer, the mechanically prepared specimens were electropolished in a 1:6 HzS04, CHSOH solution for 10 to 15 sec at 20 v. Final polishing was done with a vibratory polisher using 0.05-p alumina. Various etchants including nital, ferric chloride, and hot ferricyanide (Murakami's reagent) were used to bring out details in the different transformation products. The ferricyanide etch was used whenever the preferential etching of carbides was desired.

Jan 1, 1969

By J. R. Morison, M. P. O’Brein, J. W. Johnson, S. A. Schaaf

The force exerted by unbroken surface waves on a cylindrical object, such as a pile, which extends from the bottom upward above the wave crest, is made up of two components, namely: 1. A drag force proportional to the square of the velocity which may be represented by a drag coefficient having substantially the same value as for steady flow, and 2. A virtual mass force proportional to the horizontal component of the accelerative force exerted on the mass of water displaced by the pile. These relationships follow directly from wave theory and have been confirmed by measurements in the Fluid Mechanics Laboratory of the University of California, Berkeley. The maximum force exerted by breakers or incipient breakers is impulsive in nature, reaching a value much greater than that produced by unbroken waves but enduring for only a short time interval. This impulsive force represents the ultimate development of the accelerative force and is produced by the steep wave front and large horizontal acceleration at the front of a breaker. This impulsive force greatly exceed. the drag force computed from the particle velocities of the breaker. The reader is cautioned that these preliminary results are applicable only to single piles without bracing and are likely to be modified somewhat where multiple piles are driven, one within the influence of the other or where multiple piles are connected by submerged bracing. This paper is essentially a preliminary report submitted at this time because of the current importance of wave forces in the design of offshore structures. An extended series of additional experiments is planned for the near future. Theoretical Relationships For the sake of simplicity of treatment, the theory will be developed from the equations for waves of small amplitude. The horizontal displacement of a water particle is described by the equation 2p cosh — (d + z) H L 2pt X =----------------------sin ----- . , (1) 2 2pD T sinh------ L The horizontal component of the orbital velocity is obtained by differentiation with respect to time as 2p cosh — (d + z) pH L 2pt u = ------------------- cos— .... (2) sinh- L The acceleration of the water particles at any position is obtained by again differentiating with respect to time as 2p cosh — (d + z) 9 u -2vH L 2pt -----=----------------------------sin ----- . . (3) 3 t T2 2pd T sinh------ L where H = wave height — ft L = wave length — ft d = still water depth — ft z = depth below the still water measured negatively downward — ft. T = wave period — sec t = time — sec The force exerted on a differential section, dz, in length is pD2 s u pD 1 dF= [CM (p/4) st + Cn/2 u2] dz • • (4) where D = pile diameter — ft p = water mass density — slugs/ft3 C, = coefficient of mass C,, = coefficient of drag Substituting for a s u/s t arid u2 from Eqs. (3) and (2), the force per unit length at any position z is dF p2 pD H2 &apos; / = — [- fM sin ? ± fD cos2 ? ] . . . (5) dz 2T2 fM D fD 2pt Cm = pA/H:CD = A2;? = T [+ cos2 ? for 0 < ? < p/2 cosh— (d+z) 3p L — < o < 2p Sin L -cos2 ? for p/2 <? <3p/2 The sin 9 term (inertia) i- negative for 0 < 0 < p and positive for p < ? < 2p. Values of A and A&apos; appear in Fig. 1

Jan 1, 1950

By P. P. Reichert, L. S. Gournay, N. T. Burdine

An investigation of equivalent pore entry radii in typical samples of petroleum reservoir rock and the pore volume associated with each value of pore entry radius has been made. Theoretical discussions together with experimental procedures for obtaining pore entry radii and the distribution of pore volume with pore entry radii are presented. Experimental results on a number of core samples, along with typical distribution curves, are shown. Data on the per cent of the pore volume filled by mercury at a pressure of 1500 psi are included. The results of re-runs of samples, made possible by regenerative apparatus, show the repeatability of the data and indicate the amount of physical change in the samples by mercury penetration. Theoretical equations for calculating permeability from pore size distribution data were derived and the results of such calculations are compared with measured gas permeability data. The effect of the shape, surface area, and weight of the sample on the pore size distribution of reservoir rocks was investigated experimentally. Mercury capillary pressure curves are compared with those obtained by the porous diaphragm method using pas to displace water. Standard core analysis techniques, in general, lead to quantities which are statistical averages of the varying properties of the samples under examination. Although such statistical information has real value in predicting the gross performance of porous bodies. it fails to provide fundamental information concerning the properties of the porous medium itself or any processes which may be occurring in it. For example, a gas permeability measurement on a core sample is an indirect way of determining an average pore radius for that particular sample. Since there are many combinations of pore radii that will give the same radius. and, hence, the same permeability, no information is obtained on the pore size distribution. Furthermore, similar values in permeability do not imply similarity in other properties of a porous medium. For instance, it is possible to have two core samples with identical permeability which would have different residual oil contents at the end of an air-oil drive, or even different amounts of interstitial water. It has been recognized for some time by the petroleum industry that a determination of pore size distribution for porous reservoir rocks offered promise of increased understanding of fundamental flow processes in the porous matrix. and therefore of petroleum res- ervoir performance in general. There have recently been published several methods for determination of pore size distribution in porous materials. A report is given here of the modifications in equipment and technique required to adapt one of these methods to measurements on petroleum reservoir core samples. Although only a few correlations or applications of the method are available for presentation at this time, the technique is brought to the attention of the industry so that the opinions and experience of others with this or similar techniques may be exchanged. It seems possible that the method will have wide application in the future. METHOD There are three general methods which may be employed to measure the pore size distribution in naturally occurring rock formations. One method1 is based on experimentally determined adsorption isotherms for calculating the surface area of the porous medium. Knowing the surface area and the pore volume, a rough estimate of the pore radius can be made. Since this method depends on the thickness and uniformity of the adsorbed layer, the validity of the results would be highly questionable. A second method utilizes capillary pressure data obtained by static dis-

Jan 1, 1950

By M. D. Hassialis

[Surface Areas of Concentrates and Collector Coatings (T.P. 2002, by A. M. GAUDIN and G. S. PRELLER, Min. Tech., May. Discussion by M. D. HASSIALIS and the authors) . I Activation of Minerals and Adsorption of Collectors (T.P. 2082 by J. ROGERS and K. 1&apos;. SUTHERLAND, Min. Tech., Nov. Discussion by A. F. TAGGART and the authors). . . . 3 Correlation between Mineral Behavior in Cataphoresis and in Flotation (T.P. 2005 by A. If. GAUDIN and S. C. SUN, Min. Tech., May. Discussion by M. D. HASSIALIS). . . . . . 8] Surface Areas of Concentrates and Collector Coatings M. D. HASSIALIS.*-In the current flotation theories there exists a common gap spanned by a common assumption pertaining to the arrangement and orientation of the collector ions at the solid surface. Also common is the belief that contact angle and flotation performance are dependent upon the arrangement and orientation of collector ions. This stimulating and informative paper sheds some light upon this general problem. One of the indices of arrangement is the area available per collector ion; in this connection, Gaudin and Preller have applied the B.E.T. method for surface determinations. In a surprising number of cases, their results show a greater specific surface for tailing than for concentrate. This cannot be accounted for by the differences in specific gravity and is attributed to the presence of clay minerals of "primary" sluices in the tailing. This is not a satisfactory explanation, for experience shows that when free slimed clay minerals are present in a flotation cell they will be carried mechanically into the concentrate. A part of the answer to the decreased specific surface of the concentrate would appear to be its usual flocculated condition, yet this should not entirely account for the large spreads reported. The possibility occurs that the nitrogen adsorption isotherms for clean mineral and collector-coated mineral are different. If that were true, and if the coated mineral surface exhibited decreased adsorptive powers, the discrepancy might vanish. In discussing the disposition of collector ions at mineral surfaces, the authors adopt the more consistent viewpoint that there exists some agreement between the ions of the substrate and those of the superstrate. In the case of xanthate ions on galena, a possible arrangement is shown in Fig. 2. This arrangement shows every xanthate ion being shared by two lead ions, whereas the chemical composition calls for two xanthate ions for each lead ion (p. g). This whole discussion is misleading. In the first place, it is known that xanthate ions are not abstracted by unoxidized galena, hence Fig. 2 should show as the substrate not Pbs but PbS„ Om. It would be equally erroneous to use the lattice arrangement of PGSO4, since the surface properties of xanthate-conditioned anglesite differ from those of xanthated galena. It is highly probable that the state of the galena surface exploited in its flotation is ephemeral, since weathered galena is only poorly, if at all, collected by xanthate. Just how a substrate of oxidized galena is to be pictured depends upon one&apos;s conception of the transformation from galena to anglesite. This writer is inclined to the following sequence of events. Surface sulphide ions undergo progressive oxidation. As more oxygen is taken up by the sulphide ions they become displaced from their equilibrium positions in the galena lattice, thus accommodating for the larger volume of the S„ Om ions. Concomittant with this change the forces acting on the lead ions

Jan 1, 1946

By R. E. Holmes, T. W. Leland

The solution to the unsteady-state mass- and heat-transfer equations describing the adsorption of a dilute component from a gas stream flowing through a packed bed is readily applicable to the design of hydrocarbon recovery units. The solution to these equations depends on the assumption of a linear equilibrium equation to relate concentrations on the surface to concentrations in the gas. This assumption is shown to be justifiable for components which are very dilute in the gas stream. This approach permits the prediction of the effects of bed shape and size, cycle time, and gas mass velocity on the recovery of each component. It also allows the time and gas flow rate needed for regeneration to be determined. The equations involve a constant for each component and another constant characterized by the type of adsorbent. These constants must be evaluated from operating data. Values of these constants determined for silica gel are presented. This paper points out the type of experitrrental data needed for a thorough design of hydrocarbon adsorption units. INTRODUCTION The growing importance of adsorption processes to recover hydrocarbons from natural-gas streams has created an urgent need for better methods to design and predict the performance of these processes. Since the original use of solid adsorbents in natural-gas processing was for dehydration, most of the current design methods for hydrocarbon recovery re extensions of those developed earlier for dehydration. These methods are based on an adsorptivity or bed loading factor defined as the amount of a particular component adsorbed per unit weight or per unit volume of the packed bed. The recovery of a given component is then expressed as an empirical function of its adsorptivity on a given adsorbent. In spite of the simplicity and initial utility of these methods, they are not completely satisfactory in that they do not predict the effect of the dimensions of the bed in relation to flow rate and cycle time, and do not predict the distribution of various components along the length of the bed. It is possible, however, to make a considerable improvement in the design of these processes by applying the basic equations of mass and heat transfer applicable to gases containing small concentrations of adsorbing components flowing through granular beds. These equations have been developed and solved by Anzelius,&apos; Furnas,% nd Hougen and Marshall." where G = mass velocity of the inert constituents (assumed to be methane), lb/hr-sq ft, y = weight of an adsorbing component in the gas per unit weight of inert, lb of a given constituent per lb of methane, x = bed length, ft, p, = packed bed density, lb/cu ft, P, = gas density, Ib/cu ft, f = void fraction in the bed, t = time, hours, and w = weight of a given component adsorbed per unit weight of adsorbate free solid, Ib/lb pure adsorbent. The term on the left side of Eq. 1 represents the flow rate per unit bed volume of a component entering less the flow rate per unit bed volume of that component leaving the differential bed length. The terms on the right side represent, respectively, the accumulation rates per unit bed volume on the solid and in the gas phase within the differential bed section. The last term is negligible for this application since pgfv is quite small in comparison with p, and G. The partial differential is determined by the mass-transfer rate between gas and solid in the differential section.

By P. A. Beck, Hsun Hu

As described by means of quantitative pole figures, the annealing texture of highly rolled aluminum consists of the four retained components of the rolling texture near (123) [121], rather more sharply developed, and of a cube texture component. Local reorientation corresponds fairly well to 40 rotation around a [111] axis. In copper strip rolled 96 pct, the annealing texture is mainly the cube texture, with the four twin orientations as minor components. The annealing texture of highly rolled brass strip consists of four components of the (225) [734] type. REVIEWS by Wassermann,&apos; Barrett,&apos; Dunn,3 and Richards&apos; give detailed accounts of the numerous publications dealing with annealing textures in rolled polycrystalline metals. Although a considerable amount of information of an empirical nature has been available for many years, even relatively recently the state of recrystallization-texture theory was considered uncertain. The reviews referred to above deal mainly with the description of experimental results, without developing generally applicable principles, suitable for explaining the observed annealing textures. The investigations of Burgers and Louwerse5 and Barrett6 showed that in deformed single crystals of aluminum the orientation of the recrystallized grains deviates drastically from that of the deformed matrix. According to Barrett and to Beck and Hu,7 the relationship between the two orientations can be best described as a rotation of about 40° around a [111] axis. Recent investigations led to similar orientation relationships for various face-centered cubic metals with a simple texture, regardless of whether the annealing process was recrystallization (strain-free grains growing in a highly deformed large crystal of aluminum&apos; or copper: or in deformed cube texture copper") or coarsening (strain-free grains growing at the expense of an essentially strain-free, fine grained, polycrystalline matrix of single orientation texture copper,&apos;" aluminum,&apos; or nickel-iron). Barrett" pointed out the possibility that this orientation relationship may be a result of the orientation dependence of the rate of grain boundary migration. More recently, considerable evidence became available in favor of this view.12,13 In apparent contradiction to the above results, it has been known for a long time that the recrystallization texture of polycrystalline metals is often similar to the deformation texture. This was found, in particular, for the fiber textures obtained by wire drawing, compression, or compression rolling.&apos; Following a suggestion by Barrett,2 Kronberg and Wilson and Beck and Hu7 described a mechanism by which a [Ill] fiber texture, resulting from plastic deformation, may be retained upon recrystallization, even though the orientation of individual recrystallized grains differs from that of the local area of the matrix in which they grow. This mechanism assumes that the reorientation corresponds to a rotation around the [1ll] axis, which is also the fiber axis. The present investigation was undertaken to examine in detail the orientation relationship between deformation texture and recrystallization texture in rolled face-centered cubic metals, using the quantitative methods of texture determination that have recently become available.", &apos;" Quantitative pole figures for the rolling textures of such metals were reported recently." Quantitative pole figures for annealing textures are given in the present paper. It was planned to investigate whether or not the orientation relationship previously found for the recrystallization of deformed single crystals, and for coarsening of single-orientation texture material, is capable of accounting for the observed, often complex, annealing textures in rolled polycrystalline metals. The question whether local reorientation is predominant, even in the early phases of the annealing process, was to be studied with high purity aluminum. by making use of an oxide film and sensitive tint illum-

Jan 1, 1953

By J. W. Marx, R. H. Langenheim

The injection of heat-bearing fluids may offer a wider application to secondary and tertiary recovery from conventional oil reservoirs than inderground combustion since the process is more easily controlled and the reservoir requirements, in general, are less critical. In all cares, conduction heat losses to overburden and un-derburden will impose an economic limit upon the size of the area which can be swept out from any one injection point for any given set of conditions. The present report describes a method for c.rtin~ating thermal invasion rates, cumulative heated area, and theoretical economic limits for sustained hot-fluid injection at a constant rate into an idealized reservoir. Full allow-ance is made for non-productive reservoir heat losses. Required solutions can be obtained directly from the numerical tables given here, as soon as all operating conditions are specified, withou extensive mathematica1 ~nanipulation on the part of the user. The injection of a heat-bearing fluid into a reservoir is frequently proposed as a means of secondary or tertiary oil production. This form of thermal recovery may offer a wider application to conventional oil reservoirs than underground combustion since the process is more easily controlled and the reservoir requirements, in general, are less critical. Because of its large gross heat capacity, steam appears to be the most efficient heat injection medium, although mixtures of steam and other gases, hot water, hot oil and hot non-condensable gases also have been employed. Whatever the nature of the injection medium, economic evaluation of such thermal recovery processes will depend upon thermal invasion rates, or rates of productive reservoir heating, at any given time after the start of heat injection. In all cases, conduction heat losses to overburden and underburden will impose an economic limit upon the size of the area which can be swept out from any one injection point, for a given set of reservoir conditions, at any given heat injection rate. The present report describes a method for estimating thermal invasion rates, cumulative heated area and theoretical economic limits for sustained heat injection at a constant rate into an idealized reservoir, making full allowance for non-productive reservoir heat losses. Required solutions can be obtained directly from the nu- merical tables given here, as soon as all operating conditions are specified, without extensive mathematical manipulation. It should be noted that ordinary water flooding may be used to move an annular-heated zone outward, even though the economic areal limit for straight heat injection has been reached. Thus well spacing need not be confined to the areal limits as determined here. However, the present calculations do not cover such supplementary heat scavenging programs. The operating element consists of a radial flow system, concentric about the point of injection, with the idealized step function temperature profile illustrated by the dashed line in Fig. 1. The solid curve shown in Fig. 1 gives a qualitative picture of the true radial temperature distribution. It will be shown later that the expressions given below, which are derived from the simplifying step idealization (dashed line in Fig. I), also can be interpreted in terms of the more realistic temperature distribution shown in Fig. 2. For this case, the thermal invasion radius is simply redefined as the distance from injection well to the mid-point of the temperature distribution.

By J. F. Havard

Gypsum is a useful industrial mineral found abundantly on the earth&apos;s crust. It is inexpensive to mine and process, and its calcined products have a wide range of readily controllable properties such as strength, density and setting time. It has proven to be such a useful material indeed, that ten American companies, operating some 57 calcining plants in 25 states in 1958, produced or imported in that year a total of 13,649,000 tons of the crude mineral valued at $39,361,000, which they then converted into manufactured products with a value of $329,070,000. Gypsum (CaSO4.2H2O) is calcium sulfate with two molecules of combined water, which are responsible for most of its useful properties. It is closely associated in most deposits with anhydrite (CaSO4), which contains no combined water and has limited commercial value in the United States. Man has long recognized the useful qualities of gypsum. It was utilized by the Egyptians in the construction of the pyramids and, later, by the Romans for important structures. Many of the ancient peoples prized gypsum for artistic and ornamental purposes, carving statuary from alabaster and making casts with plaster. The tabular variety, selenite, was used for windows, and the light transmitted through these windows reminded people of light from the moon (selene), hence the name selenite. The use of gypsum continued through the Middle Ages and into modem times. Benjamin Franklin was a famed exponent of gypsum because he applied ground gypsum to clover fields in the form of large letters which later read, in the more luxuriant growth, "land plaster used here." Gypsum is still used as an effective conditioner for some soils, but in recent decades, particularly in North America and Europe, it has become much more important as a major material for the building industry. Description Gypsum and anhydrite are closely associated minerals. Gypsum is found in a number of forms: massive rock gypsum, alabaster, selenite, satin spar, and gypsite. Anhydrite is found as massive rock or as smaller bodies or isolated crystals included in gypsum. Massive Rock Gypsum comprises most of the commercial gypsum and occurs as a sedimentary rock, interbedded in most places with shale, limestone or dolomite. This rock is soft and crystalline. Its color is white or shades of gray, pink, yellow, brown or other colors. Alabaster is a pure, compact and fine-grained variety suitable for use in sculpture or turning into artistic forms; it may be white or selected for attractive coloration. Selenite is gypsum crystallized in flat, transparent, flexible foliated plates, found in clays or in surface vugs in gypsum. Satin Spar is a fine silky fibrous variety with the axes of the crystalline fibers perpendicular to the vein or joint in which it has formed. Gypsite is an earthy mixture of gypsum with clay and sand in secondary formations; it is sometimes useful as a soil conditioner and has been used in making base-coat plasters. Pure gypsum contains 20.9 pct combined water, 46.6 pct sulfur trioxide (SO3) and 32.5 pct lime (CaO). Standard specifications (American Society for Testing Materials Designation C 22-50) read that minimum purity for material to be called gypsum is 70 pct CaSO4.2H20. Most of the commercial gypsum is 85 to 95 pct pure as produced. Impurities in

Jan 1, 1960

By M. H. Gaskell, D. M. Kehn, G. T. Pyndus

A correlation of the bubble point pressure for black oil systems is developed using the standard physical-chemical equations of soiutions. The correlation is based on 158 experimentally measured bubble point pressures of 137 independent systems and is expressed in terins of the usually measured field pnrameters— flash separation gm-oil ratio, rank oil gravity, total gas gravity, and reservoir temperature. The data were obtained on systems produced in Canada, Western and Mid-Continent01 United States, and South America. The average error (algebraic) in the representation is 3.8 per cent, and the maximum error encountered is 14.7 per cent. INTRODUCTION In the absence of experimentally measured properties of reservoir fluids, it is often necessary for the field engineer to make estimates regarding the fluid properties based on the usually measured producing parameters. To aid in these estimations, various correlations have appeared in the literature in recent years. Among the pertinent properties of interest is the bubble point pressure. A correlation for this parameter has been reported by Standing&apos;. However, this correlation was based essentially on California produced crudes and this limitation was pointed out with its presentation. The correlation presented in this paper utilized data on crude oil systems from Canada, Wes- tern and Mid-Continental United States, and South America. CORRELATION DEVELOPMENT The basic assumption used in this development is the same as employed by Standing&apos;, There is a wide variety of ways to combine these parameters; however, in this instance the combination was made on the basis of Henry&apos;s law2. Accordingly, the relationship proposed is Although Eq. 2 defines an individual system, it is of limited value since H&apos; is a function of gas-phase composition and the system temperature. It was observed that for the systems where the bubble point was measured at several temperatures that the ratio of the bubble point pressures and the ratio of the corresponding absolute temperatures (R) were practically identical. Thus, for correlation purposes the bubble point pressure may be taken as a direct function of the absolute temperature. This relation is valid only for those systems that are not near the critical point. Accordingly, this correlation will be inadequate for systems in the region of the critical point. The solubility of the various hydrocarbons found in the gas phase increases with the molecular weight. Thus, the saturation pressure should be inversely related to the gas gravity. Applying these principles to Eq. 2 and rearranging terms gives: The variables 02 the left side of Eq. 3 were designated as the "hubble point pressure factor". The number of mols of tank oil per barrel is a function of the "mclecular weight" of the tank oil. Although the tank oil is a complex mixture, it was assumed for the purposes of this correlation that a unique molecular weight could be assigned to a given oil. This was designated as the "effective molecular weight", and was related to the oil gravity, This empirical relationship was developed simultaneously with the correlation by assuming values of M,. and working to obtain a smooth curve for both the correlation and the effective molecular weight. The relationship between the oil gravity and the effective molecular weight used in this correlation is shown in Fig. 1. The effective molecular weight is somewhat higher than the molecular weight of the C fraction. The difference between these values is largest for the low-gravity systems. It is noted that this effective molecular

By D. E. Thomas

Oxidation rate constants were determined for Cu-Pd and Cu-Pt alloys as a function of alloy composition and temperature. Reaction products were identified. Relationship between oxidation rate constants and diffusion constants in the reaction zones is discussed. THE mechanism of oxidation of alloys is consider--&apos;¦ ably more complex and not so well understood as that of pure metals. The oxidation of a one-phase binary alloy of which one component is a noble metal should logically be the simplest case of alloy oxidation, for in this case one is concerned presumably only with the oxidation of the base metal and the diffusion process by which it reaches the reaction site. This had led a number of investigators to study such systems. Probably the earliest work was that of Tammann and Rienacker&apos; on the tarnishing of Cu-Au alloys at temperatures up to 300°C. These alloys oxidize according to the logarithmic law, that is, the film thickness is proportional to the logarithm of the time. The rate of film formation was found to decrease with increasing gold content. Raub and Engel² investigated the oxidation of Au-Cu, Cu-Pd, Au-Ag-Cu, Au-Pd-Cu, and Ag-Pd-Cu alloys at 750°C in air. These alloy systems form a continuous series of solid solutions at the temperature of oxidation with the exception of those containing silver. Au-Cu alloys oxidize parabolically, the rate constant decreasing slowly with increasing gold content up to about 15 atomic pct* Au, and more rapidly thereafter. An alloy with 14 pct Cu forms only a very thin layer of CuO on the surface and probably also a subscale.† Alloys containing more than 14 pct Cu have scales consisting of CuO and subscales of Cu,O embedded in nearly pure gold. The Cu-Pd alloys obey the parabolic law except for slight deviations for alloys containing 53 and 84 pct Cu. The overall oxidation rate decreases rather smoothly with increasing palladium content. A scale consisting of a thin layer of CuO and a thick layer of Cu²O and a subscale of Cu²O embedded in nearly pure palladium was observed for alloys containing 84, 53, and 30 pct Cu. An alloy with 19 pct Cu formed only a subscale of CuO embedded in nearly pure palladium, and an 8 pct Cu alloy formed only a thin film which was presumed to be PdO. The ternary alloys considered by Raub and Engel oxidized in much the same way as did the binaries. Wagner and Grunewald³ found that Ni-Au alloys, oxidized at 900°C in oxygen, formed a scale of NiO and a subscale containing NiO and gold. The overall oxidation rate increases with increasing gold content, passes through a maximum and then decreases to zero for pure gold. The fact that gold increases the oxidation rate was attributed to "pores" in the scale. Kubaschewski&apos; investigated the air oxidation of alloys of platinum or gold with up to 10 pct Cu or Ni at temperatures in the range 300" to 1550°C. Parabolic behavior was noted for all alloys except Au-Ni, with rates decreasing in the order Au-Cu, Au-Ni, Pt-Ni, Pt-Cu. The diffusion coefficients for the latter three systems are known, and they decrease in the same order. However, activation energies for the oxidation of these alloys do not agree with the activation energies for diffusion in the respective alloy systems. Kubaschewski and Goldbeck7 nvestigated the oxidation of Ni-Pt alloys in air at temperatures of 600"

Jan 1, 1952

By K. G. Davis

Dilute alloys of silzer in tilz haz been solidzjzed a1 controlled rules, in lzorizontal tubes 2 mrz and 0.5 rn in diam. Radioactive; tracer techniques we?-e used to study solute distvihutions along llze specimens and irmpurity substructures, as functions of the conditions growth. The results have heen mzalyzed using Burton, Prim, and Slichter&apos;s tnodel for the solute disty-ihution in the liquid ahead of an advancing solid-liquid interface. DECANTING techniques have been used to establish criteria for the formation of impurity substructure during solidification in several alloy systems An analysis equating the appearance of impurity substructure with the incidence of constitutional supercooling was developed,= in which diffusion was assumed to be the predominant mode of solute mixing in the liquid. Substitution of experimental data into the equations derived from the diffusion analysis gave reasonable values for solute diffusivity in the liquid. However, in these investigations solidification rates of 10 cm per hr and over were used, to minimize the effect of natural conection, whereas for crystals of high perfection lower solidification rates are needed, usually between 1 and 5 cm per hr. A knowledge of the conditions under which impurity substructures will be formed at low growth rates, and the degree of segregation to be expected, is therefore of interest. In the present investigation, radioactive-tracer techniques have been used to study the effect of growth rate, initial solute concentration, and size of specimen on the formation of substructure in uni- directionally solidified rods of dilute silver in tin alloys, over a range of growth rate between 0.5 and 10 cm per hr. Criteria for the formation of substructure were established by auto radiography. This was believed preferable to the decanting technique, for the relationship of the structure on a decanted interface with that of the freezing interface is not clear, since a layer of liquid is left on the surface following decanting.&apos; The effect of substructure on the distribution of solute along the rods was also investigated. EXPERIMENTAL The procedure for sample preparation has been described in detail by einber. Alloys were prepared from tin of 99.999 pct purity and silver of 99.99 pct purity. A"&apos;, an emitter of both y and 0 radiation, was used as tracer. Samples of the alloys were drawn up into silica tubes with inside diameters 0.5 or 2 mm, remelted in a horizontal furnace, and solidified at controlled rates. A few centimeters of the samples were left unmelted for a measure of the initial concentration. Total sample length was approximately 20 cm. The temperature gradient in the furnace was kept constant at 36°C per cm in the region corresponding to the melting point for tin. To find how well this corresponded to the actual temperature gradient in the melt, a thermocouple of 38-gage wire was electrically insulated with a thin layer of Sauereisen cement and placed within one of the 2-mm-diam tubes, which was then filled with tin. The maximum diameter of the coated wire was 0.5 mm, the bead of the thermocouple junction being no larger than the diameter of the wire. A plot of temperature vs distance traveled by the furnace is given in Fig. 1 for a rate of furnace travel of 1 cm per hr. The temperature gradient in the liquid

Jan 1, 1967