Search Documents

By A. L. Barnes

Residual oil in watered-out reservoirs is a tremendous reserve which has been unrecoverable by established production methods. A study of the new recovery methods indicated that the forward combustion urocess might- recover oil from such reservoirs; however, no thermal recovery operating experience in a watered-out system was available. The Delaware-Childers pilot thermal test was undertaken to test the feasibility of thermal recovery in this watered-out reservoir. The pilot test consisted of a 2.22-acre, inverted five-spot in the 600-ft deep Bartlesville sand. The reservoir in the pilot area had a porosity of 20.6 per cent, a permeability of 118 md and an average sand thickness of 45 ft. The reservoir contains a 33' API, 6-cp oil. Combustion was started Nov. 22, 1960. The initial air injection capacity was 750 Mscf/D, but it was eventually increased to 2,000 Mscf/D. The test was surrounded by an active water flood; therefore, water production was initially high, but decreased as the heat wave moved toward the producing wells. Oil-bank arrival at an individual well was indicated by a drop in GOR and WOR, and an increase in oil production. Combustion-front arrival was evident at three of the pilot producers, and they were plugged. Cumulative oil production from pilot area wells war over 12,000 bbl. Operational difficulties were negligible and only conventional equipment was necessary. The combustion efficiency of this test averaged over 80 per cent. Results from coring showed that the leading edge of the combustion front tended to be wedge-shaped but a nearly complete sweep of the reservoir was eventually obtained. An isopach map based on evidence from 10 core holes and the existing wells showed that 126 acre-ft had been swept by the heat wave. Using this swept volume, an air requirement of 15.7 MMscf/acre-ft was calculated. It was calculated that 275 ,STB/acre-ft was consumed bv the heat wave. INTRODUCTION There is a large amount of oil remaining in reservoirs that have been water flooded. A study of ways to recover this oil showed that the forward combustion process might be applicable. Results from a number of forward combustion tests have been reported in the literature, but none of these tests were conducted in a watered-out system. The Delaware-Childers pilot thermal test was initiated in 1960 to define the operating characteristics of underground combustion in this watered-out Bartlesville sand reservoir, The purpose of this paper is to present the pilot test results in detail. FORWARD COMBUSTION PROCESS The forward combustion process consists of initiating combustion in the formation surrounding an injection well and driving this heat wave through the formation toward offset producing wells. As the combustion front progresses through the reservoir, oil and formation water are vaporized, driven forward in the gaseous phase, and recon-densed in the cooler part of the formation. These distilled liquids, water of combustion and gaseous combustion products, form a bank or three-phase region ahead of the burning front. This bank pushes mobile reservoir fluids toward the production wells. The rate of movement of the combustion front is controlled by the rate at which the nondistill able residue which serves as process fuel can be completely burned off the sand. The production performance from a heat wave conducted in a watered-out oil reservoir will differ from one conducted in a dissolved gas-depleted reservoir because of the difference in fluid saturations. The primary depleted reservoir contains connate water saturation, relatively high oil saturation and some gas saturation. The watered-out reservoir contains a highly mobile water saturation, residual oil saturation and little gas saturation. As the combustion front moves forward in either type of depleted reservoir, it drives the distillable oil, the water in place and the water of combustion ahead, and burns the nondistillable portion of the oil. The heat-wave process in a watered-out reservoir differs from the process in a

Jan 1, 1966

By D. Harrington

Efficient ventilation of metal mines consists in having such complete control of air currents that there is always supplied at placcs where men work sufficient moving air to allow working at maximum capacity without injury to health; and in case of underground fire or of surface fire in the vicinity of mine openings, underground air currents may be quickly reversed if desired, or air may be sent into or excluded from any region and fire fumes confined to only part of the mine workings, instead of penetrating practically the entire mine. Health and safety of workers in mines as well as proper safeguarding and operating efficiency of mining properties are so intimately associated with proper ventilation of mines (both coal and metal) that they are inseparable, yet ventilation is only too frequently neglected, especial1y in metal mines. The metalliferous operator, generally not confronted with inflammable gas or explosive dust which so frequently force ventilation of coal mines, usually disregards air supply altogether except such as may be obtained from compressed air; and generally, even when attention is given to metal-mine ventilation, the air currents rarely are found where they are needed, namely, the working places, especially the working faces. After several years' study of miners' consumption, the writer is convinced that long continued breathing of air impregnated with large quantities of any kind of finely divided dust, such as is found in a large number of the working places of our mines, will ultimately produce some respiratory disease, whether it be asthma, bronchitis, or phthisis; and the progress of these diseases is hastened if there are also present high temperatures, high humidities, or harmful gases or if there is present (and allowed to remain to be breathed) large quantities of the finely divided dust when air temperatures are low, hence favorable to maximum performance of work with accompanied maximum breathing into the respiratory passages of the harmful material. It is generally accepted

Jan 1, 1923

By John B. Hastings

The origin of the watery vapors of vulcanism has always been an object of interest and speculation to the seismologist, and as theories of the genetic origin of ore-deposits have of late years been pretty well narrowed down to the expiring forces of plutonic action, the same question has attracted mining engineers and geologists, as is well shown by the discussions of the subject in our Transactions. The important part taken by volcanic emanations in the origin of pegmatites and quartz-veins, described in my paper, Origin of Pegmatite,' and their latent power to concentrate into useful deposits such scattered gold as occurs in the Hartsel granite, make a discussion of their derivation but a natural third and final step. It is coilceded that enormous amounts of vapor accompany vulcanism, though perhaps we are apt to forget that steam has 1,700 times the volume of water, besides which the column seen over Vesuvius and other volcanoes is greatly mixed with air; the immensity of such volumes compared with solids and liquids is shown by the experiment of Gautier, who, by heating dessicated granite to 100' C., evolved from it gases 20 times, and steam 90 times, its own volume. Dana appraised the average amount of water left in ordinary rocks as 2.5 per cent. T. M. Read estimated that the Mississippi river carries to the sea annually 150,000,000 tons of rock material. If these Mississippi sediments, as deposited, contained 20 per cent. of water, it would be 600,000,000 cu. ft., or 4,500,000,000 American gallons, annually. Allowing the vapor suspended over a volcanic cone to be mixed with 80 per cent. of air, this amount of water converted into steam would replenish anew, every 9 min., a column 15,000 ft. high, 2,000 ft. in diameter at the base, and • 10,000 ft. at the top. Read's estimate is only half of the amount given in a more recent and probably correct one.2

Jan 1, 1909

By D. Harrington

Efficient ventilation of metal mines consists in having such complete control of air currents that there is always supplied at placcs where men work sufficient moving air to allow working at maximum capacity without injury to health; and in case of underground fire or of surface fire in the vicinity of mine openings, underground air currents may be quickly reversed if desired, or air may be sent into or excluded from any region and fire fumes confined to only part of the mine workings, instead of penetrating practically the entire mine. Health and safety of workers in mines as well as proper safeguarding and operating efficiency of mining properties are so intimately associated with proper ventilation of mines (both coal and metal) that they are inseparable, yet ventilation is only too frequently neglected, especial1y in metal mines. The metalliferous operator, generally not confronted with inflammable gas or explosive dust which so frequently force ventilation of coal mines, usually disregards air supply altogether except such as may be obtained from compressed air; and generally, even when attention is given to metal-mine ventilation, the air currents rarely are found where they are needed, namely, the working places, especially the working faces. After several years' study of miners' consumption, the writer is convinced that long continued breathing of air impregnated with large quantities of any kind of finely divided dust, such as is found in a large number of the working places of our mines, will ultimately produce some respiratory disease, whether it be asthma, bronchitis, or phthisis; and the progress of these diseases is hastened if there are also present high temperatures, high humidities, or harmful gases or if there is present (and allowed to remain to be breathed) large quantities of the finely divided dust when air temperatures are low, hence favorable to maximum performance of work with accompanied maximum breathing into the respiratory passages of the harmful material. It is generally accepted

Jan 1, 1923

By T. M. Chance

THe necessity of adopting improved methods of bituminous-coal cleaning at many collieries is recognized by all familiar with the requirements of the various bituminous markets, the approaching exhaustion of the relatively small areas of inherently high-grade coal, and the difficulties encountered in maintaining a uniform grade of shipped coal. Many coals lose much of their market value by degradation in size, and, in any event, if the cleaning .process is to contemplate wetting the coal the minimum amount of fines should be produced to prevent sludge losses and the difficulties resulting from the moisture content of the wet fines. Hence, it is desirable to bypass the finer coal dry, if this can be done without too great increase in impurities in the final product. This procedure has given excellent results at washeries at Steelton and in the Birmingham district. If the raw fines are too impure to permit admixture with the washed coal, it may be desirable to use dry methods, such as the pneumatic table, rather than to wet an excessive amount of such fine material. The bituminous-coal cleaning plant should therefore: (1) Treat the raw coal in as large lump as possible and without sizing; (2) eliminate degradation of pure coal in the washing process; (3) avoid wetting the fines, if possible; (4) produce washed coal practically free from mechanically included impurities; (5) crush the refuse and retreat, if much intergrown coal and refuse are present, rather than precrush the entire feed. Ordinary gravimetric methods of concentration, whether hydraulic or pneumatic, will not meet all of these requirements, as the large lump includes those sizes now sent to the picking tables, if it is desired to treat material of such size. I do not know of any prior commercial method, based on the falling velocity, coefficient of friction or resistance to fracture, that permits the production of clean coal varying in size from, say, 10-in. lump to 1/16-in. mesh. The effect on the specific gravity of any given coal as a result of variations in ash and pyritic sulfur content is well known; in fact, it has been made use of in commercially ascertaining ash content by deter-

Jan 1, 1924

By E. T. Dumbles

Prof. Edward Orton, in his Report on the Occurrence of Petroleum, Natural Gas and Asphalt Rock in Western Kentucky, thus clearly states his ideas of the universal dissemination and rare accumulations of the bitumens:I "We need to bear in mind that the various members 'of the bituminous series are abundantly and almost universally distributed among the unaltered sedimentary rocks of the earth's crust. The valuable accumulations of these substances are rare, it is true, but one can scarcely go amiss' of petroleum, asphalt or gas, at least in small quantities, among the stratified rocks that retain their original structure." Speaking of the Ohio valley, he adds: "A fifth of one per cent. of petroleum, if distributed through a thousand feet of rock, would make a total to the acre, or square mile far beyond any production that has ever been realized from the richest oil field, and -percentages of this amount are not only not rare to find, but are even hard to miss." Dr. F. W Clarke in his Data of Geochemistry (Bulletin No. 491, U. S. Geological Survey, 1911), discussing these views of Orton with similar views of T. Sterry Hunt and Szajnocha, says that they "lead to the conviction that the formation of bitumens is a general process and by no means exceptional. Wherever sediments are laid down, inclosing either animal or vegetable matter, there bitumens may be produced." The organic origin of the bitumens, including petroleum, Gas long been an accepted fact with nearly all geologists, but the method, place, and time of the transformation into petroleum or other bitumen is still under 'discussion. Dr. Orton says? "The statements now presented........bring before us two main views as to the origin of petroleum, viz.: " (1) Petroleum is produced by the primary decomposition of organic

Jan 1, 1915

By H. M. Chance

By courtesy of the officials of the Chicago, Burlington and Quincy railroad, I am permitted to publish the results of an examination made in 1887 and 1888 of' the country west of the Black Hills, and lying between the Black Hills and the foot-hills of the Big Horn Mountains in the northeastern part of Wyoming. With the exception of the country constituting the foot-hills, or the encircling ridge or rim of the Black Hills proper, all of this area is occupied by rocks of Cretaceous age. In the central part of the Black Hills are found the tin-bearing granites, the mica-schists, and gold-bearing slates, already so well known. Surrounding this central area of older rocks (which should be considered as the "Hills" proper) are the attenuated representatives of the Palzeozoic, dipping gently away from the Hills in every direction, overlaid by the gypsum-bearing Mesozoic, which here forms a bold high ridge or rim, completely encircling the Black Hills, and known as the inner ridge. Overlying, and apparently conformable to this, we find the Dakota sandstone, which likewise forms a prominent ridge or rim, known as the first or outer ridge. This is the formation which contains the coal now worked at the mines near Newcastle. It is also the formation in which the best oil-wells have been obtained in the "Stoakdale," or "Beaver," and the " Belle Fourche " oil-districts. Overlying it are the Colorado shales, forming the great plains drained by Beaver creek and the south fork of the Cheyenne river, and extending west to the Belle Fourche, near Donkey creek, where the overlying Fox Hill formation (thin) and the Laramie group, the great lignite-formation, are first seen. The Laramie group occupies the surface from the Belle Fourche at Donkey creek west to the foothills of the Big Horn mountains at Buffalo, an air-line distance of some seventy or eighty miles.

Jan 1, 1891

By R. T. DeHoff

In any structural transfortnation which is driven by surface tension, the geometric variable of fimdamental importance is the local value of the mean surface curvatuve. Acting through the suvface free energy, this quantity determines the magtnitude of both the pressure and the chemical potential that develops in the neighborhood of an arbitrarily curved surface. A metallographic method which would permit the quaniitatiue estinzation of this propevty is of fundarnerztal irztevest to studies of such processes. In the present paper, it is shoun that the average value of the mean surface curvature in a structuve can be estimated from two simple counting measuretnents made upon a vepresentative metallograpIzic section. No simplifyirlg geonzetric assurmptions are necessary to this deviuation. It is further shoum that the result may be applied to parts of interfaces, e.g., interparticle welds in sintering, or the edge of growing platelets in a phase transformation, without loss of validity. In virtually every metallurgical process in which an interface is important, the local value of the mean surface curvature is the key structural property. This is true because the mean curvature determines the chemical potential of material adjacent to the surface, as well as the state of stress of that material. The theoretical description of such broadly different processes as sintering,1,2 grain growth,3 particle redistrib~tion4,5 and growth of Widmanstatten platelets8 all have as a central geometric variable the "local value of the mean surface curvature". The tools of quantitative metallography currently available permit the statistically precise estimation of the total or extensive geometric properties of a structure: the volume fraction of any distinguishable part:-' the total extent of any observable interface,10,11 and the total length of some three-dimensional lineal feature:' and, if some simplifying assumptions about particle shape are allowed, the total number of particles.'2"3 The size of particles in a structure, specified by a distribution or a mean value, can only be estimated if the particles are all the same shape, and if this shape is relatively simple.14-16 The relationships involved in converting measurements made upon a metallographic section to properties of the three dimensional structure of which the section is a sample are now well-established, and their utility amply demonstrated. In the present paper, another fundamental relationship is added to the tools of quantitative metallography. This relationship is fundamental in the sense that its validity depends only upon the observation of an appropriately representative sample of the structure, and not upon the geometric nature of the structure itself. It involves a new sampling procedure, devised by Rhines, called the "area tangent count". It will first be shown that the "area tangent count" is simply related to the average value of the curvature of particle outline in the two-dimensional section upon which the count is performed. The average curvature of such a section will then be shown to be proportional to the average value of the Mean surface curVature of the structure of which the section is a sample. The final result of the development is thus a relationship which permits the evaluation of the average value of the mean surface curvature from relatively simple counting measurements made upon a representative metallographic section. The result is quite independent of the geometric or even topological nature of the interface being studied. QUANTITATNE EVALUATION OF AVERAGE CURVATURE IN TWO DIMENSIONS The Area Tangent Count. Consider a two-dimen-sional structure composed of two different kinds of distinguishable areas (phases), Fig. l(a). If the system is composed of more than two "phases", it is possible to focus attention upon one phase, and consider the remaining structure as the other phase. The reference phase is separated from the rest of the structure by a set of linear boundaries, of arbitrary shapes and sizes. These boundaries may be totally smooth and continuous, or piecewise smooth and continuous. An element of such a boundary, dA, is shown in Fig. l(b). One may define the "angle subtended" by this arbitrarily curved element of arc, dO, as the angle between the normals erected at its ends, Fig. l(c). Now consider the following experiment. Let a line be swept across this two-dimensional structure, and let the number of tangents that this line forms with elements of arc in the structure be counted. This procedure constitutes the Rhines Area Tangent Count. Suppose that this experiment were repeated a large number of times, with the direction of traverse of the sweeping lines distributed uniformly over the semicircle of orientation.' Those test lines which ap- proach from orientations which lie in the range O to O + dO form a tangent with dA; those outside this range do not, see Fig. l(c). Since the lines are presumed to be uniformly distributed in direction of traverse, the fraction of test lines which form a tangent with dA is the fraction of the circumference of a semicircle which is contained in the orientation range, dO; i.e., vdO/nr or dB/n. If the number of test lines is N, the number forming tangents with dA is N(d0/n). Since each test line sweeps the entire area of the sample, the total area traversed by all N test lines is NL2. The number of tangents formed with dA, per unit area of structure sampled, is therefore

Jan 1, 1968

By G. St. J. Perrott

During the past year, the Bureau of Mines has carried on an investigation of liquid-oxygen explosives (L.O.X.) to supplement the work described in previous publications.' The present paper gives results of the first part of this work, which was a laboratory investigation of the properties of typical combustibles used in L.O.X., and the relation of these properties to the absorption and retention of oxygen by the explosives and their explosive characteristics. No attempt will be made to describe the development of liquid-oxygen explosives, because this phase of the subject has been well covered.2 The L.O.X. cartridge consists of a paper wrapper filled with an absorbent combustible material that is saturated with liquid oxygen by soaking it therein. After saturation, the cartridge is removed from the liquid and fired with fuse and cap, or electric detonator, in a manner similar to other explosives. Certain types of cartridge may be detonated with fuse alone, requiring no cap to initiate the detonation. ' By suitable variation of the nature and density of the combustible, cartridges having a wide variety of explosive characteristics may be made.

Jan 1, 1925

By Richard Henry Lee

Since the economies in the blast furnace resulting from enriching iron ores are so great, much attention has been paid during the past few years to the various methods of concentrating lean ores, and, as the concentrated ore is usually of extreme fineness, various methods of agglomeration and sintering, of more or less value, have been put into operation. The resulting agglomerated concentrates are generally obtained in the form of briquettes or nodules. The briquettes naturally divide themselves into two classes: (1) those made by the mixture of some binding agent, and then formed into briquettes under great pressure; and (2) those made by sintering the concentrates, the latter either being formed into bricks before exposure to heat or the sintered mass broken into fragments afterward. Of the first class I will not speak, as they are not used on an extensive scale in this country. The second class of briquettes, or those made by sintering, are simply masses of melted or fused silicate and oxide of iron mingled with more or less silicates of aluminum, lime, and magnesia. The fact that the material in a briquette is sintered is proof positive that there are no pores in the material. There are, however, quite a number of holes of greater or less diameter through the gubstance of the briquette. They are not pores in the common acceptance of that term as applied to ores by furnacemen, as the ides of the holes and channels are fused. In reality the material is simply mill cinder. It is practically untouched by the gases in the upper part of the furnace, and the iron has to be reduced by solid carbon in the boshes and hearth. Briquettes sometimes show a little saving in fuel in the furnace over an ore mixture of large lumps, but that saving is made simply because, owing to the numerous holes and channels through the mass, the briquette is practically composed of numerous small or fine lumps, and, as is well known, the finer the

Jan 1, 1914

By A. U. Seybolt

DURING the course of experiments involving oxygen equilibrations with a high-purity Pd-5 at. pct Rh alloy, the appearance of a subscale was noted. Most of the heat treatments in a pure oxygen atmosphere were performed at 900°C. The presence of the subscale was noted when the oxygen partial pressure was in excess of approximately 95 mm, up to 1 atm, the highest pressure used. According to available thermodynamic information' on the free energy of formation of Rh2O3 (the only reliably reported solid oxide of rhodium), this oxide should not be stable under these conditions, nor, of course, any oxide of palladium. Extraction of the subscale from the matrix was affected by treatment with aqua regia, and the resulting X-ray diffraction powder pattern is shown in Table I. This pattern is not that of Rh2O3, nor that of any known rhodium or palladium oxide. It can be indexed on a hexagonal lattice with a. = 5.22Å and co = 6.0Å. In addition to this unknown material, there was a weak Rh2O3 pattern. An X-ray fluorescence analysis of the powder gave 3214 palladium counts per sec and 5381 rhodium counts per sec, thus indicating the likelihood of a double oxide of palladium and rhodium. In view of the fact that the above result was obtained on a single sample, it is perhaps best not to insist upon the above ratio of about 0.6, but possibly to tentatively assume 0.5 or 1/1. The small amount of Rh2O3 in the X-ray pattern might have occurred on cooling, and it seems possible that the double oxide, below some temperature level, is not as stable as Rh2O3. To examine this point, some of the extracted double oxide was heated on a sheet of pure palladium in air at 900°C, and allowed to furnace-cool over a period of several hours. The X-ray diffraction pattern of the powder showed approximately the same intensity of Rh2O3 and the "hexagonal" oxide as before, but, in addition, a rather faint pattern of another crystalline species made its appearance. This finding again suggests partial transformation of the major (double) oxide to other oxides on cooling from 900°C. Application of the phase rule shows that only one equilibrium oxide (subscale) could have been present at temperature. Vacuum-fusion, oxygen analysis of the extracted subscale showed 7.7 ± 0.7 pct O. Combining this information with that of the X-ray fluorescence analysis suggests the formula PdRhO. This compound should have an oxygen content of 7.07 pct, which is within the range of error of the oxygen analysis. However, until a more careful stoichiometric study is made, it is suggested that the formula be written

Jan 1, 1965

By Courtenay DeKalb

Revision of the United States mining law is needed chiefly because of the following reasons: 1. The conceptions as to the characteristics of orebodies that were held at the time the statute of 1872 was enacted have since proved to be in many respects erroneous. 2. The operation of the existing law has been found to work unnecessary hardship upon many claimants to mineral land. 3. The existing statute fails in large degree to encourage development of mineral resources. 4. The existing law often produces conflict between placer and lode-claim rights, working unnecessary injustice to placer claimants. 5. The methods of establishing the rights of locators on United States mineral land are defective, and are not uniform throughout the States within which such lands exist. Law of the Apex The objections to the so-called "law of the apex" are so well known as to require no detailed statement. It is sufficient to point out that the apex rule was based upon the notion that ore deposits consisted of well-formed veins included between definite walls, like the slice of ham in a sandwich. The fact is that veins conforming to that simple type are rare. Irregularity is the rule, and the chief metal production of the United States comes from mass? which bear no resemblance to the tabular form of vein. Manifestly the law of the apex fails completely in such cases. Moreover, the tendency is constantly toward the exploitation of ores of lower grade than could formerly be worked, and such deposits exist mainly in the form of large irregular impregnated zones and masses, so that the future development of our mineral resources would be continuously embarrassed by shadowy claims to extra-lateral rights by the locators of so-called apexes.

Jan 1, 1915

By R. Dawson Hall

The stresses in the simplest structures are often those we find most difficult to analyze. The most complex condition in mine stresses is found in simple tunnels where the roof, the sides, and the floor are a monolith. The functions of the parts are like the parts themselves not distinct and spccialized, and the problems to be solved are like those in a metal structure with riveted joints or a redundancy of bars. This difficulty explains perhaps why the condition has not been treated. But just because it cannot be discussed in its entirety is no reason why it should be treated as an action of parts with spccialized functions as a roof beam with supports and a foundation. The problern cannot be ignored on the ground that it is not of sufficient importance to warrant careful consideration, because conditions of complete monolithism, of which the tunnel is the type, are found materially unchanged in room-and-pillar and in longwall work. This unity between roof, sides, and floor, which to the coal miner is a difficult conception, really deserves a scientific appellation, and perhaps holoid (from holos, whole, and eidos, form) will serve the purpose as well as any other. In a simple tunnel the roof, the sides, and the floor form integral parts of one and the same structure, and the distortion of one cannot be conceived without a consequent strain in the others. Thus when the roof of the tunnel droops by reason of its weight, the upper parts of the sides are drawn in becausc they are integrally connected with the roof and must approach each other whenever, by the sagging of the roof, the distance between any two points in it is diminished. (See Fig. 1.) Thc sides in their turn operate on the floor of the holoid structure, producing a tensile stress. The writer has always been impressed with the value of soap as a means of illustrating the action of mine stresses. With that idea in mind' a cake of naphtha soap measuring 43/8 by 2¼ by 19i in. was taken and a tunnel was made through it 13/4 in. long, 21/2 in. wide and 1¼ in. high. (See Fig. 2.) A load was then placed at the mid-span of the tunnel. Eventually, the upper bar, or "roof," broke at the

Jan 1, 1916

By S. W. MILLE

GEORGE F. COMSTOCK,* Niagara Falls, N. Y. (written discussion?).¬I have recently had the pleasure of reading Mr. Miller's interesting paper, and would like to call attention to a reference to this subject which apparently has escaped his notice. It is an abstract of a German research on the subject of nitrogen in steel, and appeared in the Iron Age of Feb. 17, 1916, page 432. Photomicrographs of needles such as Mr. Miller found in his welds are given, and their identity is discussed. The conclusion reached is that the needles are slip lines due to the brittleness of the ferrite crystals caused by their absorption of nitrogen. The deformation necessary to develop the slips is supposed to be accomplished either in cutting or polishing the microsections or by cooling strains after welding. It seems very reasonable to expect that nitrogen would he absorbed by steel in either electric or oxy-acetylene welding, and the reference I have mentioned gives instances of many unusual structures resulting from the presence of considerable nitrogen with carbon in steel. But the nitrogen is .rapidly given off from steel by ordinary annealing in air, hydrogen or vacuum, and this would explain the disappearance of Mr. Miller's needles after annealing. I think the conclusion that the needles are cementite might well be revised in view of this German work on nitrogen.

Jan 5, 1918

By H. W. Gillett

Many of the parts of motor cars, aircraft, etc., that require strong light construction, hence must be made of high-quality steel, are stressed to the maximum limit only in a very small volume. In parts subject to bending stress a line or even a point may take the maximum stress. A series of endurance tests under repeated bending in progress in the U. S. Bureau of Mines laboratories, like similar tests by other investigators, has shown the great difference in life of sister bars of the same stecl, handled in the same way and tested at the same nominal stress. It is known that a surface notch or scratch greatly increases the local stress over the nominal calculated stress; internal notches, such as those formed by inclusions or sonims, probably have a similar effect. From the tetss made by the Bureau of Mines, the cleanliness of the steel at the dangerous section, or point of maximum stress, seems to be one of the most important factors in determining the life of the piece. The more localized the stress, the more does chance, rather than the average properties, dctermine the life of the steel. The usual test, a tension test of a bar taken longitudinally, is not sensitive to the local drop in strength (or tendency to increase the true local stress over the nominal) because of inclusions, which probably have a more injurious effect in hard heat-treated steels, such as must be used when great strength is sought, than in softer steels. Users of steel who make transverse tests find surprisingly low ductility on transverse bars of dirty steel, though the longitudinal tests may be good. Bending tests, reverse bending tests, and notch-bar impact tests,

Jan 1, 1923

By Peter B. Scotland

The mines of the Arizona Copper Co. are situated in the Morenci-Metcalf copper district in southeastern Arizona. This copper-bearing district covers a triangular mountainous area of about 3 square miles, rising abruptly from the gravel plateau of the surrounding country. In this area, an immense intrusion of porphyry lias displaced, shattered, and engulfed the shales, limestones, and quartzites formerly bedded on the basal granite. Outcrops of oxide ore were discovered in 1873, and these surface ores were found to connect in depth with large bodies of high-grade oxide ores in the limestones and shales. The mining of these high-grade ores continued until about 1893, when their rapid exhaustion led to the discovery and exploitation of the low-grade sulphide ores in the adjoining porphyry. Methods of concentration were then devised and the low-grade ores finally rendered profitable. The Arizona Copper Co. and the Detroit Copper Mining Co., operating in the same district, were the pioneers in the successful development of the low-grade "porphyry" properties of to-day. The largest mines of the Arizona Copper Co. are the Humboldt and Clay at Morenci, and the Coronado, Metcalf, and King at Metcalf. These mines produce about 4,000 tons daily of concentrating ore containing from 2.5 to 2.8 per cent. copper. The topography of the country is very rugged and mining operations are conducted principally through adit levels. A few of the mines are opened by shafts, the deepest being 1,100 ft., in the Coronado mine. Ore Occurrence The low-grade sulphide ore occurs as: (1) disseminated deposits in the main stock of quartz porphyry; (2) lode deposits in fault fissures in granite. The high-grade oxide ores were found as tabular deposits in limestone and shale close to contacts with porphyry dikes. Low-grade oxide ore formed the outcrop of some of the sulphide orebodies; the majority of the outcrops, however, were barren.

Jan 1, 1915

By Noel Cunningham

Many excellent descriptions of the mills of the Porcupine district have been written, but no discussion exclusively devoted to the metallurgical technology has been given. These notes are intended to cover this feature briefly. They are based upon 21/2 years' mill operation in the district—i.e., practically since the beginning of metallurgical operations. Character of the Porcupine Ore.—There is no oxidized ore in the district, the surface having been deeply planed by glacial action in recent geologic time. The precious-metal content is about in the proportion of 85 of gold to 15 of silver by weight; hence, the silver is practically negligible. There are two classes of Porcupine ore, having very different characteristics; these will be referred to throughout this paper as Class A and Class B. Class A ore is a pure quartz with inclusions of schist. Generally it is heavily fractured and breaks down readily to sharp, hard grains, about minus 10 plus 20 mesh, requiring further comminution to release the gold. It carries very little pyrite; the gold is entirely free and apt to be coarse, but often spongy, going into solution readily on that account. This gold is 60 per cent. to 85 per cent. free milling, depending on the grade of ore. Class B ore is an iron silicate schist, strongly laminated, carrying 4 to 5 per cent. pyrite; its specific gravity is 2.8 to 3.0, depending upon the amount of mineralization. In breaking the ore in the mine, generally over 25 per cent. of material through a 1/2-in. ring is made; the ore readily breaks down in milling and makes a comparatively large amount of non-crystalline slime; owing to its high specific gravity, however, it is quick settling. In my opinion, the gold in this ore is free, but so finely divided that it will neither pan nor amalgamate; it appears to be disseminated through the rock and not chiefly associated with the pyrite. Veins of Class A ore occur with or without side walls of Class B, and veins of Class B occur unassociated with Class A; more often the veins are closely banded, Class A and Class B alternating, generally with Class B in excess. Both classes of ore are more or less blocky at times, and with reference to Class B this is indicative of low gold content.

Jan 1, 1915

By Joseph W. Richards

This method of briquetting flue-dust, or flue-dust mixed with fine ores, or, in a few exceptional cases, coke-dust, has come into large commercial use in Europe, and a small plant is already in operation in the United States. It promisea to become of such great importance to the iron industry of the United States that the following description will certainly interest the majority of our pig-iron producers. Discovered in 1908, the process Tests upon the observation of Dr. Schumacher that blast-furnace flue-dust, while possessing of itself no binding or cementing properties, acquires strong cementing properties if mixed with a very small amount of certain salt solutions, the amount of which is so small that the resulting cementation appears to be rather by catalytic action of the salts added than by the mass-action of such chemicals. To be more specific, fresh blast-furnace flue-dust mixed with from 5 to 10 per cent. of its weight of magnesium chloride or calcium chloride solution—that is to say, with from 0.25 to 2 per cent. of its weight of magnesium chloride or calcium chloride—acquires the property of setting within a short time, from 15 to 60 min., and forming a hard cemented briquette. Alkaline solutions appear to have no action such as described, and they even interfere, if present, with the action of the magnesium and calcium solutions. When treated in this way the flue-dust briquette sets very hard, apparently from pure excess of cementing- and setting-power. It is, therefore, possible to mix with the flue-dust a considerable proportion of inert ore or like material, which has no setting-power by this process, and thus to make a compound briquette containing large quantities of ore mixed with flue-dust, but in which the flue-dust may be regarded as the cement or binding-material. A particularly strongly cementing flue-

Jan 1, 1913

By H. W. Gillett

Many of the parts of motor cars, aircraft, etc., that require strong light construction, hence must be made of high-quality steel, are stressed to the maximum limit only in a very small volume. In parts subject to bending stress a line or even a point may take the maximum stress. A series of endurance tests under repeated bending in progress in the U. S. Bureau of Mines laboratories, like similar tests by other investigators, has shown the great difference in life of sister bars of the same stecl, handled in the same way and tested at the same nominal stress. It is known that a surface notch or scratch greatly increases the local stress over the nominal calculated stress; internal notches, such as those formed by inclusions or sonims, probably have a similar effect. From the tetss made by the Bureau of Mines, the cleanliness of the steel at the dangerous section, or point of maximum stress, seems to be one of the most important factors in determining the life of the piece. The more localized the stress, the more does chance, rather than the average properties, dctermine the life of the steel. The usual test, a tension test of a bar taken longitudinally, is not sensitive to the local drop in strength (or tendency to increase the true local stress over the nominal) because of inclusions, which probably have a more injurious effect in hard heat-treated steels, such as must be used when great strength is sought, than in softer steels. Users of steel who make transverse tests find surprisingly low ductility on transverse bars of dirty steel, though the longitudinal tests may be good. Bending tests, reverse bending tests, and notch-bar impact tests,

Jan 1, 1923

By Sidney Powers

Since the opening of the Wheeler oil and gas field in Carter County and the discovery of oil near Lawton, Comanche County, Okla., in 1904, interest has been aroused regarding the origin of the oil in the Permian "Red Bed" region which lies between the Wichita and Arbuckle Mountains on the north and the Red River on the south. The later development of the Healdton, Loco, Duncan, Fox, and Graham fields south and west of the Arbuckle Mountains has brought the region into prominence. Recent discoveries of Ordovician and of Pennsylvanian fossils in wells in the Healdton field and of Pennsylvanian fossils in the Fox and Graham fields are of such importance from a scientific and a commercial standpoint that the occurrences and the problems arising therefrom are here briefly described. Producing oil and gas sands in the southern Oklahoma fields, with the exception of those in the Cretaceous and underlying rocks in the vicinity of Madill, Marshall County, are associated with the Permian "Red Beds" or with the underlying Paleozoic strata. In the two fields farthest south of the Arbuckle Mountains, Healdton and Loco, production has been entirely confined to sands at depths of 700 to 1400 ft. (213 to 416 m.) and only recently has a producing sand as deep as 1860 ft. (567 m.)l been encountered. These sands are found near and below the base of the red rocks and were supposed by Wegemann and Heald2 to belong in large part to the basal Permian, Wichita formation, or to the immediately underlying formations. Fossils in the blue shales and in the limestones associated with the deeper sands now prove them to be Pennsylvanian and all the producing sands at Healdton are found to be of this age. In the fields nearest the Arbuckle Mountains, the Wheeler sands at a depth of about 700 ft. (213 m.) appear to be of Permian age,

Jan 1, 1918