Search Documents

By R. S. Archer

The proper representation of equilibria involving graphitic carbon in the constitutional diagram of the iron-carbon system is admittedly an unsolved problem, the complete solution of which will probably require the establishment of more experimental evidence than is at this time available. The object of this paper is to present the author's observations on some of the phenomena in question and his interpretation of this and other recorded evidence. The chief of the recently disputed questions upon which the author has experimental evidence concerns the occurrence of graphitization at temperatures below the Al point. In a paper1 presented at the September, 1919, meeting of this Institute, the following is found: "the results given would seem to indicate that the graphite eutectoid lies at a smaller value of carbon content than has been previously supposed. At least this is true unless there is either a marked formation of graphite eutectoid at these rates of cooling, or a decomposition of pearlite into graphite, both rather unlikely suppositions, but not impossible ones." In a discussion of this paper, H. A. Schwartz2 takes the position that the possibility of graphitization occurring below the A1 point is an open question, but that complete graphitization (to less than 0.10 per cent, combined carbon) commonly occurs above this temperature. Another opinion from the malleable castings industry is found in a recent paper3 by Touceda: "Also the carbide of iron can be broken up into its two soft constituents at the temperature referred to. This temperature is called the critical temperature, or critical range, and for air-furnace hard-iron castings it is in the vicinity of 1440" F. It is the

Jan 1, 1922

By R. S. Archer

The proper representation of equilibria involving graphitic carbon in the constitutional diagram of the iron-carbon system is admittedly an unsolved problem, the complete solution of which will probably require the establishment of more experimental evidence than is at this time available. The object of this paper is to present the author's observations on some of the phenomena in question and his interpretation of this and other recorded evidence. The chief of the recently disputed questions upon which the author has experimental evidence concerns the occurrence of graphitization at temperatures below the Al point. In a paper1 presented at the September, 1919, meeting of this Institute, the following is found: "the results given would seem to indicate that the graphite eutectoid lies at a smaller value of carbon content than has been previously supposed. At least this is true unless there is either a marked formation of graphite eutectoid at these rates of cooling, or a decomposition of pearlite into graphite, both rather unlikely suppositions, but not impossible ones." In a discussion of this paper, H. A. Schwartz2 takes the position that the possibility of graphitization occurring below the A1 point is an open question, but that complete graphitization (to less than 0.10 per cent, combined carbon) commonly occurs above this temperature. Another opinion from the malleable castings industry is found in a recent paper3 by Touceda: "Also the carbide of iron can be broken up into its two soft constituents at the temperature referred to. This temperature is called the critical temperature, or critical range, and for air-furnace hard-iron castings it is in the vicinity of 1440" F. It is the

Jan 1, 1922

By Christopher H. Bierbaum

The first significant fact observed in the study of bearing metals is that not a single pure homogeneous metal has given satisfactory service; all bearing metals are alloys made up of two or more phases; that is, they consist of hard and of relatively soft microscopic particles intimately mixed. The function of the hard particles, or bearing crystals, is to support the load and resist the wear when actual metallic contact exists between the bearing surfaces. The functions of the softer particles are to allow the harder particles to adjust themselves to the surface requireinents of the journal and to wear down slightly below the surface of the harder, forming slight depressions on the apparently smooth wearing surface of the bearing, in which some of the lubricant is held when the bearing surfaces are brought into contact with each other. It is this characteristic of certain alloys to form these slight depressions, and thus provide the means for retaining a lubricant, that characterizes them as true bearing metals; in fact, a bearing metal has been defined as "an alloy that is capable of retaining a lubricant upon a bearing surface."' The extent to which the lubricant can be so held determines the most valuable characteristic of an alloy as a bearing metal. An alloy which, perhaps, most characteristically represents a bearing metal is the composition of copper and tin that contains sufficient tin to produce the tin-copper eutectoid, or delta crystal. The depressions worn upon the surfaces of the softer crystals of the teeth of a motor-truck worm wheel, made of an ll-per cent. tin bronze, in many cases were from 5 to 6 microns in depth; all other conditions remaining constant, this depth of wear increases with an increase of working pressure. This copper-tin bronze contains intercrystalline shrinkage cavities, which also

Jan 1, 1923

By Christopher H. Bierbaum

The first significant fact observed in the study of bearing metals is that not a single pure homogeneous metal has given satisfactory service; all bearing metals are alloys made up of two or more phases; that is, they consist of hard and of relatively soft microscopic particles intimately mixed. The function of the hard particles, or bearing crystals, is to support the load and resist the wear when actual metallic contact exists between the bearing surfaces. The functions of the softer particles are to allow the harder particles to adjust themselves to the surface requireinents of the journal and to wear down slightly below the surface of the harder, forming slight depressions on the apparently smooth wearing surface of the bearing, in which some of the lubricant is held when the bearing surfaces are brought into contact with each other. It is this characteristic of certain alloys to form these slight depressions, and thus provide the means for retaining a lubricant, that characterizes them as true bearing metals; in fact, a bearing metal has been defined as "an alloy that is capable of retaining a lubricant upon a bearing surface."' The extent to which the lubricant can be so held determines the most valuable characteristic of an alloy as a bearing metal. An alloy which, perhaps, most characteristically represents a bearing metal is the composition of copper and tin that contains sufficient tin to produce the tin-copper eutectoid, or delta crystal. The depressions worn upon the surfaces of the softer crystals of the teeth of a motor-truck worm wheel, made of an ll-per cent. tin bronze, in many cases were from 5 to 6 microns in depth; all other conditions remaining constant, this depth of wear increases with an increase of working pressure. This copper-tin bronze contains intercrystalline shrinkage cavities, which also

Jan 1, 1923

By T. Lane Carter

Before describing the experience with the Chinese on the Rand and the work they have accomplished, it will be necessary, first, to give a brief account of labor-conditions in the Transvaal since the war, and then to show how the necessity of importation of labor arose. As is well known, the Transvaal mines are run on the dual system of labor—that is, the rough work is done by colored laborers under the superintendence of white men. From the start of mining operations in South Africa there has been the cry of shortness of native labor, due in great measure to the failure of Kaffirs to work continuously in the mines. While he works, the Kaffir is a satisfactory laborer, but his period of service is short, averaging about nine months. People unacquainted with the Kaffir have maintained that, by offering a higher wage and better accommodation, better results would be obtained from the native workers, but an increased wage simply aggravates the trouble. The Kaffir's wants are few. While at work Be spends little of his money, and before long has sufficient capital with which to buy wives and become a gentleman of leisure. Doubling the wage of the Kaffir means that he acquires a competency in half the time, so that his period of service is correspondingly reduced. In 1899, before the war, there was always a cry about the scarcity of Kaffir labor. The highest number of natives at work was in July and August, 1899, when nearly 100,000 were employed. At the outbreak of hostilities the Kaffirs were scattered far and near, many doing well during the war by working for the military authorities. On the resumption of mining operations on the Rand a serious mistake was made. Based on past experience, it was argued that if the whole industry decided to start anew with

Jan 1, 1909

By E. von Maltitz

In his highly interesting paper, Piping and Segregation in Steel Ingots,' Prof. Howe emphasizes the effect of successive phases of internal pressure in the ingot in the evolution of gas, and the consequent formation of blow-holes. From his statements in other places, it may be inferred that he does not here intend to ignore the other variable factor, temperature, but rather to discuss this one more particularly. At all events, it is my purpose not to engage in controversy with Prof. Howe, but, rather to contribute, towards the complete elucidation of this important subject which we all desire, my own views and experience. If, in doing so, I specially emphasize other factors than pressure, I need not be understood as denying what I do not think it necessary to discuss fully. Nor, in presenting my own original conclusions, need I be understood as claiming to be the first who ever reached or announced them. Many things are asserted or suggested upon inconclusive evidence; and to confirm such tentative propositions may be as valuable a service as to overthrow them. In the following passage, Prof. Howe adduces analogies, based upon the behavior of charcoal and of water, respectively, which seem to me questionable : "In general, the solvent power falls as the pressure falls ; and in general it rises as the temperature falls. Thus, to heat a solid, for instance charcoal, may expel part of its dissolved gas ; and a tumbler of water drawn cold from the faucet gradually evolves gas, as it stands and warms up on the sideboard." (p. 72.) Charcoal is a solid body, which has the property not only of absorbing gases in large quantities, but also of expelling the thus absorbed gases upon heating. A comparison between charcoal and iron as to the absorption of gases is scientifically not possible; the gas-content of charcoal is partly due to the

Jan 1, 1908

By Hugh M. Roberts, R. D. Longyear

Introduction ............................ 27 GEnERal Geology........................... 29 The ORebodY in Western Falco~ridgI TownsRip........... 31 Quartzite-Graywacke Formation................... 33 Greenstone............................ 33 Norite ............................. 33 Metamorphism.......................... 35 The Orebody........................... 36 Mineralogy ........................... 37 Grade of Ore........................... 42 Genesis oF tEe Ores . :....................... 43 Summary of Various Hypotheses.................. 44 Magmatic Segregation by Crystallization of Sulphides........ 44 Gravitational Segregation of Molten Sulphides at the Base of the Magma 45 Intrusion of Molten Sulphides after the Consolidation of 'he Nurite.. 45 Deposition by Hydrothermal Solutions.............. 46 Magmatic Segregation by Extraction from Crystallizing Norite... SO The Relationship between the Exploration and Theories of Origin .... 50 Volume Relations of Norite and Sulphides............... 62 Intimate Association of Norite and Sulphides............. 53 Granitic Material........................ 54 Uniform Content........................ 54 Sulphides in Walls......................... 54 Absence of Typical Hydrothermal Minerals.............. 55 SUmmaRY................................ 56 Introduction During 1916 and 1917. the E. J. Longyear Co. of Minneapolis. Minn., carried out a campaign of exploration for nickel-copper ore in the Sudbury District of Ontario. The work was initiated by W. E. Smith. a resident of Sudbury. who called the attention of W. J. Mead. Chief Geologist

Jan 1, 1918

By Samuel S. Wyer

The art of natural-gas compressing is now over 25 years old, and has grown at practically the same rate as the increase in domestic natural-gas consumers. There are now over 200 natural-gas compressing stations in North America, aggregating more than 320,000 hp. of compressor capacity and representing a property value of more than $22,000,000, and compressing more than 85 per cent. of all the gas used. The age and magnitude of the art make it evident that the use of gas compressors is a recognized integral part and universal custom of the natural-gas business. The public also is not without its rights and vital interests in this problem. Approximately 1,700,000 domestic natural-gas consumers in North America are dependent upon gas compressors for their natural-gas service. That is, if the use of compressors were to be prohibited, the majority of these consumers would be unable to secure adequate natural-gas service. Each consumer represents between four and five persons, and it therefore follows that the comfort and well-being—as far as natural-gas service is concerned—of at least 8,000,000 persons would be affected if the use of natural-gas compressors should be prohibited. These 1,700,000 consumers have invested, in services, house piping, fixtures, and appliances, an average of about $90 each, or an aggregate of $153,000,000, which is much more than the companies' investment in gas compressors. Furthermore, in all cases where the rate paid by the consumers is fair to the gas company—considering the value of the service rendered by the gas company—the consumers are entitled to continued service and protection of the investment they have made on the faith that the gas service would be continued in the future. Since "Customs adopted and acquiesced in, if not in conflict with federal or State legislation, have the force of positive law,"l and ('Courts will take notice of whatever ought to be generally known withxn the limits of their jurisdiction,"2 there ought to be no question as to the un-

Jan 1, 1916

By D. J. McAdam

Results of investigation of corrosion-fatigue of metals at the U. S. Naval Engineering Experiment Station, Annapolis, Md., have been discussed by the writer in several recent paper~.1,2,3,4 In those papers references were also given to the work of Haigh in 1917.= Efforts by the writer to obtain a better understanding of some of the factors involved in corrosion-fatigue finally developed into a general investigation of the effect of time and cyclic stress on corrosion of metals. Corrosion-fatigue of Metals As described in the papers mentioned, rotating-cantilever specimens, conically tapered so that the stress is nearly uniform over a length of about 1.5 in., were subjected to simultaneous fatigue and corrosion. For this purpose a stream of water was diagonally applied so as to sweep the specimen from the outer to the inner fillet and surround the stressed surface with water. The fresh water is a calcium carbonate water, the composition of which has been given in a previous paper.2 The salt water is Severn River water having a saline content about one-third that of sea water. The previous papers described results obtained with ferrous and non-ferrous metals. The experiments showed that even slight corrosion simultaneous with fatigue may cause failure at nominal stresses far

By William H. Kobbé

The word recovery as used in this paper is applied in its broader sense and not limited to wells producing from horizons of unconsolidated sands. Certain problems connected with the winning of petroleum from such horizons present themselves while drilling is in progress and should be considered before drilling is commenced wherever unconsolidated sands are expected. Maximum recovery depends not alone. upon efficient pumping methods but also upon the selection of a proper drilling system and the completion of a well especially adapted to the extraction of these oil-bearing sands. 11. DRILLING Determining Factors in Selection of Method The selection of a drilling method for the development of a region in which the oil reservoir consists of unconsolidated sands is based on the following considerations: (1) Character of the formations overlying the reservoir; (2) thickness of the oil-bearing stratum or strata; (3) thickness and character of water or gas sands; (4) gas pressure to be encountered or expected; (5) total depth of well. 1. Character of the Formations Overlying the Reservoir The strata overlying the reservoir may consist of beds of shales, clays, sands and other soft materials, or they may be slates, limestones and sandstones consolidated to all degrees of hardness. Very often the overlying strata are predominantly of soft materials but interbedded with harder formations. Likewise, soft strata are encountered at different horizons in an overburden consisting almost entirely of the harder sedimentaries. The physical character of this overburden is frequently

Jan 1, 1917

By Alexander L. Field

The Bureau of Mines is investigating the problem of slag viscosity, its variation with the temperature and with the composition of the slag, and its effect upon the distribution of the sulphur between molten iron and slag, as introductory to a series of contributions to the theory of the metallurgical processes. The method of measurement, viscosity apparatus, furnace and other accessories mentioned in this paper have been described fully in s Bureau of Mines report.1 The Literature on Slag Viscosity The viscosity of blast-furnace slag had not been measured previous to the investigation described in this report. A number of investigators have determined the "fusibility," or softening temperature, of slags by means of the cone method .or other deformation method, but these methods supply only limited information regarding the temperature-viscosity relations of the slag in question. Any deformation method that may be employed indicates only the temperature at which the slag attains a more or less definite viscosity., the magnitude of the value obtained depending on the method used. For details of the various methods used by different investigators, see the Bureau of Mines paper already referred to. An isolated measurement by Doelter on a single mixture at 1,300" C. represents the highest temperature reached in the various viscosity investigations previous to those described in this report, in which results have been referred to absolute units. Arbitrary deformation tests have of course been made at much higher temperatures.

Jan 1, 1917

By Victor O. Homerberg, Dexter N. Shaw

A study of the correlation of the mechanical properties and of the microstructure with the heat treatment of 60-40 brass has been confined, heretofore, to the rolled or extruded material as received from the mannfacturer. The results obtained by Babson and Buhler,' Bengough and Hudson12 Stead and Stedman,3 and Brayton4 have been confined to the treatment of the material as received. No attempt was made to get the material into a given condition and then to work from this basis. To start with a given structure would have the decided advantage of making the work independent of the original condition, hence, to make the results reproduceable. In a previous paper, it was shown, in connection with the study of the transformation that occurs at about 470" C., that if specimens were quenched to produce the beta structure and then reheated, the beta would begin to break down, at approximately 200" C., into a very finely divided alpha. It was predicted that important results might be obtained if test pieces were to be given a similar double heat treatment and then tested for the mechanical properties as well as a study of the microstructure. The material used in the present investigation was a 3/4-in. round bar of extruded muntz metal of the following composition: Copper, 61.05 per cent.; zinc (by difference), 38.90 per cent.; lead, 0.05 per cent.; iron, trace; tin, nil.

Jan 1, 1924

President MRS. REED W. HYDE 84 Mountain Ave. Summit, N. J. First Vice-President MRS, WILLIAM A. SCHEUCH Trent St. Great Kills, S. I., N. Y. Second Vice-President MRS. THORNS E. LLOYD Box B Netcong, N. J. Third Vice-President MRS. H.. T. HAMILTON 24 Ridge Rd. Summit, N. J.' Fourth. Vice-President MRS. R. A. PALLANCH 1342 Laird Ave. Salt Lake City, Utah

Jan 1, 1939

Chairman James F. Kemp :—I call upon Prof. Albert Sau-veur to open the general discussion on the subject of sound steel ingots. Albert Sauveur, Cambridge, Mass.:—I believe that I have the privilege, this instant, of opening one of the most important, significant and far-reaching discussions ever held before this Institute. I believe that our talk this morning will be heard far and wide, not only on this side of the water, but also on the other side. Everywhere, in short, where steel is manufactured. I welcome the opportunity of expressing my mind in regard to the production of sound steel ingots, a subject about which I entertain Rome very decided opinions. I shall not attempt to discuss the relative merits of the various processes that have been described. I shall, on the contrary, confine myself to a general consideration of the important questions before us. So intensely do I feel regarding the production of sound steel ingots that I have put my remarks on paper in my desire to present my views. I have always remembered my astonishment, not to say dismay, some twenty years ago, when I beheld for the first time a steel ingot, a rail steel ingot, that had been split open from top to bottom. There was the pipe! There was an enormous cavity extending from a short distance from the top to nearly one-third of the length of the ingot; and when I was told that manufacturers seldom discarded more than one-tenth of the total length of the ingot it became evident to me that a large proportion of piped, and therefore, defective, or at least weak and dangerous, rails were manufactured; in fact, probably one rail out of six, nearly 17 per cent., of dangerous rails.

Jan 1, 1914

By D. Foster Hewett

The scope of this paper is the description of two districts in Peru in which deposits of vanadium have been found, and the consideration of much laboratory-work that I and others have done to determine the nature of these deposits. It is with regret that I present some of the data in a state of evident incompletion, particularly the analyses of a few of the minerals, which leaves some doubt as to whether the true nature of the migerals is understood. I make no apology, however, since in this case, as in many others referring to ore-deposits, conclusive opinions cannot be stated until a great amount of work has been done, and the deposit has been thoroughly exploited. I believe that the data and the tentative conclusions here presented indicate a unique and interesting condition which may assist others in work along similar lines; arid further, what is of more practical importance, stimulate a search for a metal which, though long considered rare, is probably so merely because proper care has not been taken to recognize it. An excellent bibliography on the occurrence of vanadium in nature is given by I?. W. Clarke in his paper, Data of Geochemistry;' and in the preparation of this paper 1 have consulted many of the references contained in the Bibliography of the Chemistry of Vanadium, by M. Moisan.2 A brief review of the subject having special reference to the metallurgy of vanadium is contained in the small book by P. Nicolardot.3 One of these vanadium-deposits has already been briefly. 1 Bulletin No. 330, U. S. Geological Survey (1908). 2 Chimie Minerale, vol. iii. (1905). 3 Le Vanadium (1905).

Jan 1, 1910

By Hallet R. Robbins

Korea, the ancient" Hermit Kingdom," is a peninsula jutting out from the coast of eastern Asia. By the natives it is called " Chosen," nfhich, translated, means " Land of the Morning Calm." It lies between the Yellow sea and the Sea of Japan. On the north it is separated from Manchuria and the Russian province of Primorsk by the Yalu and Tiumen rivers; on the south the Korcan straits interpose a rough voyage of 120 nliles to the nearest point in Japan. The entire country is situated between the parallels of 34O and 42O N. latitude. The surface of the country is made up of successive ranges of ul~glaciated mountains, separated by narrow, fertile, and more or less densely populated, valleys. Through all the obscure centuries of its history, Korea has succeeded in maintaining a monastic seclusion, over which, from time immeniorial until the late Chino-Japanese war in 1894, China exercised a shadowy sovereignty. Although Korea had been forced into slight foreign contact previously, her first forcign treaty was signed with Japan in 1876. Under the restraining guardianship of China, the Japanese treaty bore but infiignificant innovations for Korea; but when, in 1883, a treaty was made with the United States, the first of the western nations, a decade after the American gunboats, under Commodore Rodgers and Lieutenant Schley, forced their may up the Salee river, Korea awoke from her sleep of 4,000 years. The Eorean peninsula suddenly became the arena where the enterprises and individuals of many foreign nations met in fiercest rivalry. Out of this struggle grew two singularly successful American enterprises, both of which have played an important part in developing the natural resources of the country. The first, and best known of these, is the Oriental Consolidated Mining Co., which was organized by Lcigh Hunt

Jan 1, 1909

By K. D. Hester, A. W. Fletcher

A nickel-copper sulphide concentrate was treated in a pilot plant at Warren Spring Laboratory during 1961, by a hydrometallurgical roast-leach-solvent extraction process devised to cleanly separate the metal values and produce acid sulphate liquors containing the metals. It is shown that 86 pct of the nickel and 95 pct of the copper could be leached from the calcine, after a sulphatizing roast on finely ground flotation concentrate. Iron was removed from the leach liquor by limestone neutralization with a small loss of values. Copper and nickel were separated by solvent extraction with naphthenic acid in kerosene after partial neutralization of the iron-free liquors with ammonium hydroxide. Hydrogen sulphide and chlorine were used to remove zinc (and residual copper) and cobalt impurities respectively. The recovery of pure copper and pure nickel, by electrowinning, from the acidic solvent extract strip liquors finally produced, appears technically feasible. An economic analysis of production costs shows that small, geographically isolated, nickel-copper sulphide deposits cannot usually be worked profitably by established processes. The requirements for profitable operation on a comparatively small scale could possibly be met by a flotation-roast-leach process. Two difficulties, obtaining satisfactory extraction of nickel from a sulphide concentrate and separating the copper and nickel in solution, have prevented the previous use of this method. A solution to the first problem, dissolution of the nickel, was described in a recent paper by Thornhill.1 It was shown in this paper that copper and nickel in a flotation concentrate could be oxidized to water soluble sulphates by roasting in a fluidized bed with added salt cake. Workers at the Warren Spring Laboratory have shown that the separation of copper and nickel can be accomplished by solvent extraction using a relatively inexpensive carboxylic acid, naphthenic acid. Moreover, the mineral acid required to strip values from the loaded solvent could be produced, and the metals recovered, by electrowinning; thus the latter section of the process was regenerative. The removal of iron from the leach liquor and the elimination of impurities such as zinc and cobalt before nickel electrowinning would be necessary to complete the flowsheet. The process under investigation could therefore be summarized (Fig. 1) as follows: 1) Flotation to produce a bulk sulphide concentrate. 2) Fluidized bed roasting to sulphate the nickel and copper minerals. 3) Leaching of roaster calcine to extract soluble nickel and copper. 4) Precipitation of iron from the separated leach liquor by air oxidation after the adjustment of pH and temperature. 5) Recovery of copper from the iron-free Liquor by pH adjustment and liquid-liquid extraction. 6) Purification of the copper raffinate by removing zinc and residual copper as insoluble sulphides and cobalt as cobaltic hydroxide. 7) Recovery of nickel from the purified liquor by pH adjustment and liquid-liquid extraction. Laboratory and pilot plant studies detailed below, were carried out at the Warren Spring Laboratory, to test the feasibility of each one of the unit processes and to obtain preliminary plant design data. FLOTATION The ore was an altered basic rock containing concentrations of magmatic sulphides.

Jan 1, 1964

By Harry M. Mikami, A. Gene Sidler

Chemistry of the evolution of materials in contact with copper converter tuyeres is delineated by means of analyses of periodic punch rod samples taken during a converter cycle. Lining samples from known peripheral and end locations from three converters were investigated chemically and petrographically. One set of eight specimens representative of all lining parts was removed for study before completion of the campaign. Purely surface removal by slag action is minor. Slag filling of interconnecting cracks extending to the hot face results in a "stoping'' action which shapes the hot face contour and is a significant factor. Major wear mechanism is believed to be copper metal slabbbing caused by metal first penetrating joins and invading fractures or impregnating brick structure laterally from the joints. Importance of lining design and joint fit are emphasized. New laboratory tests are indicated. In the copper converter, molten matte, which is essentially a solution of iron and copper sulfides, is blown with air to produce blister copper. During the first stage of the process the FeS component is oxidized to SOz and FeO, the latter combining with a siliceous flux to form a predominantly ferrous silicate slag. Successive increments of matte and flux are charged, blown, and skimmed of slag until sufficient CuzS ("white metal") has accumulated. This white metal is then blown to copper metal in the final or blister-forming stage by the oxidation of sulfur to SOz and the reduction of combined copper to metal. The reactions of both stages are exothermic so provide the required heat. Temperature is controlled by cold scrap copper, flue dusts, smelter reverts, and so forth. Considerable vari- ation in practices occur depending on the type of converter, grades of the matte and flu, and other factors. Lathe and Hodnett's' survey of world converter practices gives much information on these variations and their effects on the refractories. Principles of converting chemistry are presented by Newton and wilson,' Ruddle,' and schuhmann. Most copper converting occurs within the temperature range 2100" to 2370°F although individual smelters report1 ranges from as low as 1700" to 2240°F to a high of 2200" to 2400°F. Temperature intervals reported from beginning to end of blow varied from 45" to 540°F. Average temperature range was 2030" to 2260°F and the average interval 250°F During the matte-blowing stage varying amounts of magnetite (FeO.Fe,O,) are formed in the slag as suspended crystals and also the liquid portion of the slag will contain, in addition to ferrous silicate, some Fe20s which adds to the potential magnetite formation if the temperature falls. This is a component of the so-called "dissolved magnetite" often referred to in the literature. Although the slag may contain minor amounts of CaO, A1209, MgO, and alkalies, the principal components are Fe0-Fez03-SiO,. The phase equilibria relationships of this system have been elucidated by Muan~ and Schuhmann, et a1.' These data and estimates of converting atmospheres by schuhmann4 are useful tools in studying slag behavior. It would appear that in many cases reported magnetite contents of slags are apparently higher than actually is present at operating temperature. This is probably because much of it is formed during slag solidification. The quaternary systems which have Mg-0,1,0,' and addition to iron oxides and silica are also of interest in considering the reactions of the slags with basic refractories. The formation of magnetite has an important interrelationship throughout the pyrometallurgy of copper (Mossman,' Gronningsater and Drummond," Ruddle,' Elwood and Henderson") but its presence in the converter particularly relates to operating efficiency and lining life in certain instances. Archi-

Jan 1, 1963

By Roswell H. Johnson

What becomes of the water which must have filled the oil and gas sands at the time of deposition, has long puzzled students of oil and gas and has found expression in Munn's well-known article on the hydraulic theory. Both Munn and Clapp have pointed out that in the Appalachian field the deeper sands carry increasingly less proportionate amounts of water. It seems to me probable that the principal source of oil and gas has been in the shales in proximity to the sands which now contain these products. The sand spits which mark off the lagoons from the sea comply particularly with the requirements of a limited sand imbedded in shales rich in organic matter. Cunningham Craig has objected to this view that the rich organic muds of lagoons are found only at the surface. That such muds do extend to considerable depth 1 am assured by Prof. Douglas W. Johnson, who has made an extensive study of the Atlantic Coast marshes. As any particular sand body becomes weighted by a heavier and heavier overburden, the result of increasing deposition, a part of the very large percentage of water in the uncompacted sand and mud is forced out. The water percentage of freshly settled mud is vastly higher than that of the resultant shales, or even of a very porous sand. If beds of less compressible material meet or underlie the shales in question, there will frequently be a lateral motion along such beds to some point where the upward movement will be resumed. We find in our laboratory work here that oil, gas, and water have extremely slight capacity for gravitational sorting while in a state of rest, but when moving the gravitational sorting is readily accomplished. As the oil, gas, and water pass a body of larger pores, the gas, owing to its lack of capillary attraction, is retained in the large pores. This has been predicted by Washburne, Blatehley and others on the ground that the water has a higher capillarity and grips the finer pores in such a way that there will be a greater proportion of oil and gas in the large

Jan 1, 1915

By W. H. Emmons

Most mineral deposits change as they are followed downward on their dips. Some of these changes are due to primary arrangement; different ores were precipitated at different depths when the deposits were formed. Other changes are due to weathering or secondary enrichment. The chief changes resulting from weathering, in the main, are understood and standard changes are recognized. The processes are relatively simple. They take place at ordinary temperatures and pressures and can be duplicated in the laboratories. Moreover, there are thousands of deposits available for study, because the processes take place near the surface where the development of mines is begun. The changes due to primary arrangement of the deposits of the metals are not so well understood. Deposition has taken place at higher temperatures and our knowledge of the chemistry of the processes leaves much to he desired. Very few experimental data are available. The deposits, moreover, offer fewer examples because many mines are not developed to depths where the changes can be studied and a change to unprofitable material usually results in stopping work. Most students of ore deposits now accept, as confirmed, the hypothesis that nearly all lodes and related deposits were formed by solutions originating in intrusive igneous masses. Outward from these masses, the deposits at many places are grouped in zones and the arrangement noted from the intrusions outward are commonly the reverse of the changes noted from the surface downward in a single lode. A study of the changes in groups of deposits, from the parent intrusion outward, will throw light on the changes to be expected in a single lode downward. Recause the changes in series of deposits from the intrusive outward may all be observed near the surface, where more data are available, it is possible to increase the number of examples many fold and to apply the statisttical method of study with greater confidence of avoiding error. It is not everywhere possible to identify the parent igneous body to which a group of ore deposits are related. Several kinds of criteria are available; certain groups are superior to others. By applying the

Jan 1, 1924