Search Documents

By R. J. Wasilewski

The variation of elastic modulus with terrzperature between -150° and 600°C has been investigated. Compounds close to equiatomic cornposition exhibit very low modulus values and very high damping near room temperature. The modulus rises steeply with both decreasing and increasing temperature. The modulus minimum and the high damping are believed to be connected with a martensitic transformation of TiNi. In bulk material this transition takes place slightly above room temperature quite rapidly and reversibly, with a hysteresis of some 30°C, depending on the Ti:Ni ratio. Oxygen impurity affects the reaction time. THE inter metallic compound TiNi has been reported to exist in an ordered CsCl (B2) structure,l-6 the homogeneity range varying rather markedly with temperature.7 Some investigators reported this compound to decompose peritectoidally to Ti2Ni and TiNi, between 650° and 800°C,3 or below,',g the latter workers also suggesting the decomposition to be strain-sensitive. Purdy and Parr were the first to report a structural transformation to a new, possibly hexagonal, structure at 36°C,7 a temperature indubitably too low to allow the significant amount of diffusion necessary for a peritectoid reaction. Mechanical-property investigations of compositions close to TiNi just above room temperature have qualitatively shown remarkable anomalies, particularly with respect to clamping,' and to a "memory" effect, that is, plastically deformed material returning to its original shape on being heated through the "decomposition" temperature.9 The original explanation of this effect—based on the apparent experimental observation of Ti2Ni or TiNi, formation in the material subjected to tensile or compressive stresses, respectivelp—does not appear plausible. It appeared more probable that the change involved may be a martensitic, diffusionless structural transformation, similar to those observed in other B2 structures such as 0 brass,'' AuCd,ll and AuZn.12 The existence of such transformation has been established recently,', although the symmetry of the low-temperature structure is not yet known. The present paper describes the elastic modulus and damping behavior of polycrystalline TiNi in both structures. EXPERIMENTAL METHOD 1) Specimens. All the specimens to be investigated were prepared from premelted electrolytic nickel and iodide titanium by nonconsumable arc melting and casting in a water-cooled copper mold. The cast billets were canned in mild steel, extruded, and swaged to approximately 0.375 in. diam. The cans were then removed by pickling or machining. Preliminary material balance checks indicated no significant weight losses on melting (less than 5 mg on a 50-g button); hence nominal compositions have been used throughout. In agreement with previously reported observations7 no single-phase material was obtained at—or close to—Ti 1.00 Ni1.00 a small amount of finely divided second phase always being present. It was found that most of the oxygen impurity was associated with this minor phase, which was identified as oxygen-bearing Ti2Ni—possibly Ti,Ni,O. The amount of this phase—at any given Ti:Ni composi-

Jan 1, 1965

By A. M. Gaudin, C. S. Chang

IN general, fatty acids or their alkali salts do not cause clean quartz to float. However, the presence of multivalent ions, such as the alkaline-earth metal ions and heavy-metal ions, can activate quartz and thus make it respond to soap flotation. The mechanism of activation and soap flotation of quartz has been studied.1-4 The problem was attacked by making flotation tests rather than by careful adsorption measurements on suspensions of ground quartz in solutions containing the activator and the collector. Attempts have been made to determine the adsorption of barium ion and calcium ion on quartz. The results have only qualitative value as the analytical methods were not adequately precise. Artificial radioactivity and progress in radioactivity detection have introduced a new analytical tool, which can have a sensitivity several orders of magnitude greater than that of other methods.5-6 In the experimental work described in this paper the radioactive tracers, barium 140 and carbon 14, were employed. Lauric acid was synthesized, having a radioactive carbon atom and was used with Ba140 to study the adsorption of barium and laurate ions from aqueous solution on ground quartz. Flotation tests, using the vacuum flotation technique,4 were run in conjunction with the adsorption experiments. The object of this investigation was to understand better the reaction mechanism of barium activation and soap flotation of quartz. Methods and Materials Quartz Sample Preparation: Lumps of hand picked quartz, washed free of stains, were reduced in size to -20 mesh in laboratory crushers. The product was boiled in concentrated hydrochloric acid to remove the abraded iron. The cleaned product then was ground dry in a laboratory porcelain mill, using siliceous pebbles, to pass through a 200 mesh screen. The ground product was deslimed by sedimentation at 37 microns. This -200 mesh +400 mesh material was subjected again to boiling with concentrated hydrochloric acid, followed by washing with distilled water and further desliming. The cycle was repeated until no trace of iron could be detected in the wash liquor. During the final washing, the pH of the wash water was checked to insure the complete removal of the acid from the mineral. The quartz then' was rinsed with conductivity water. The resulting product was dried in a drying oven and stored in mason jars. The impurities (spectrographic) were as follows: Al, 0.01 to 0.001 pct; Li, Mg, Mn,, Na, each less than 0.001 pct; Fe and Cu not detected. The specific surface of the quartz sample was determined by the krypton gas adsorption method.7 The average of two measurements was 881 sq cm per g. The calculated specific surface for 37/74 micron quartz particles, using a surface factor of 1.96,8 is 900 sq cm per g. This is in good agreement with the measured value of 881 sq cm per g. Beta-Counting Method: The radioactive isotope of barium used in the experimental work was barium 140. It has a sufficiently long half-life, 12.8 days, emits high-energy beta particles (up to 1.0

Jan 1, 1952

By D. S. Eppelsheimer, D. N. Williams

The cold rolled textures of iodide titanium and of three samples of commercial titanium were examined using the Schulz-Decker Geiger counter technique. The iodide titanium and two of the three samples of commercial titanium showed a (0001) [1010] texture rotated 30' toward the transverse direction about an axis in the rolling direction. The third sample of commercial titanium showed a double texture. THE metals of the hexagonal system tend to deform similarly if the c/a ratios are similar. Thus titanium, zirconium, and beryllium, with c/a ratios of 1.601, 1.590, and 1.570, respectively,l should have similar cold rolled textures. The cold rolled texture of high purity iodide titanium has been described as (0001) [1010] rotated 30" toward the transverse direction about an axis in the rolling direction.' The texture of zirconium has also been reported as (0001) [1010] with a transverse rotation from the ideal position of approximately 30" about an axis in the rolling direction." This texture differs from that reported for titanium however since a continuous spread of (0001) poles toward the transverse direction was reported rather than distinct (0001) maxima 30" from the rolling plane normal. Beryllium has a texture similar to that of zirconium although the angle of transverse rotation of the (0001) poles is much less.' These three metals thus show a common type of cold rolled texture, as yet unexplained, which can be described as (0001) [1010] with various degrees of rotation toward the transverse direction about an axis in the rolling direction. Since titanium showed the greatest degree of rotation from the (0001) [1010] position, the cold rolled texture of titanium was re-examined using a semiquantitative Geiger counter X-ray technique to obtain more accurate experimental data from which a theoretical interpretation of this new type of hex- agonal rolling texture could be developed. The cold rolled textures of iodide titanium and of three samples of commercial titanium were determined. Table 1 gives the analyses of the titanium samples. Experimental Procedure Preparation of Samples: Prior to the final rolling operation each of the samples was given an initial reduction of approximately 50 pct and annealed to remove the gross effects of any previous treatments. Samples were annealed in vacuum, high purity helium, and air to determine whether annealing atmosphere had any effect on the cold rolled textures developed. All samples were annealed 1 hr at 800°C. Grain size determinations were made using the formula, 1.075 in which n is the number of grains counted in an area A (in sq mm) and M is the magnification of the area counted.' This formula gives the diameter between opposite flats assuming hexagonal grains. At least three areas containing more than sixty grains each were counted in each grain size determination. Rockwell B hardness readings were made on the annealed samples. The results of the measurements of

Jan 1, 1954

By S. L. Couling, D. J-P. Adenis

i2) twinning in poly crystalline magnesium does not usually occur homogeneously but is concentrated in localized regions or bands inclined at about 45 deg to the stress axis. These bands of twinning are in many ways similar to the Luders bands seen in mild steel alzd Al-Mg alloys. Within a hand the percentage of the volume twinned may approach 100 with no twinning outside the band. Bands are not produced in specimens of grain size a3 x 10-= in. or in samples deformed at temperatures 300°F. Annealing of heavily twinned regions leads to re crystallization textures markedly different from those found in the starting material. The exact preferred orientation appears to depend on the starting grain size, the amount of compres-sive strain and the manner in which it is introduced. MAGNESIUM, with its hexagonal crystal structure, deforms plastically at room temperature by a variety of deformation mechanisms, one of the most important of which is (1012) twinning. In single crystals such twinning occurs on compression parallel to the basal plane or tension perpendicular to it. In wrought polycrystalline magnesium, such as rolled sheet, the preferred orientation is such that almost all the grains have their basal planes nearly parallel to the sheet surface. Therefore, if sheet material is deformed by cold rolling or by tension in the plane of the sheet, deformation of the grains by (1012) twinning is not favored. On the other hand, twins form readily on compression parallel to the plane of the sheet as in a compression test, on the compression side of a bent sample, or at the outer rim of a drawn cup. The first part of this paper deals with the morphology of (1012) twinning in polycrystalline magnesium. Some aspects of this subject were covered by Barrett and ~aller.' Of direct bearing on the work to be reported here are the comments of Jetter' in discussion to Ref. 1. He shows that Mg + 1.5 pct Mn alloy sheet when bent about a transverse axis develops a pattern of transverse bands on the surface of compression. A longitudinal section through the sheet shows that the bands are wedge-shaped and inclined to the rolling direction. The bands were identified as "outcrops of regions in which deformation is localized as the result of the reorientation brought about by (1012) twinning". The second part of the paper treats the recrys-tallization texture of the specimens twinned by compression. Magnesium deformed and then annealed generally recrystallizes with no change in orientation.1'3'4 This statement is true provided that the amount of (1012) twinning occurring during deformation is small. In an isolated observation, Anse15 has shown that, when deformation produces much (1072) twinning, annealing causes new maxima to appear in the pole figure. The second part of the paper elaborates on this point. I) MATERIALS AND PROCEDURES All of the experimental work to be reported was done using the commercial sheet and plate alloy AZ31B (nominal composition: 3 pct Al, 1 pct Zn, 0.4 pct Mn, balance magnesium). This alloy is available commercially in two tempers, -0 (fully annealed) and -H24 (partially annealed), and specimens of both tempers were used in various experiments. The average grain. diameter (AGD) for -0 temper 0.125-in. sheet is about 0.5 x 10- in.; where material of larger grain size was desired, anneals at elevated temperature were used to grow the grains. compression tests were made on a screw-driven "hard" machine. The specimens were clamped in a

Jan 1, 1964

By J. Lemish

Considerable research has been conducted in Iowa in recent years on carbonate aggregate reactions in concrete. Groups outside the state have become active in the past few years after recognizing that certain carbonate aggregates are reactive in concrete. The paper reviews the nature and extent of the problem and a summary is given of research by the author and his associates. In recent years considerable research has been conducted in Iowa on carbonate aggregate reactions in concrete. The research is part of a general study on the behavior of carbonate rocks as concrete aggregates sponsored by the Iowa State Highway Commission. Research on carbonate aggregates has not been extensive in the past. Laughlin1 published one of the first papers on carbonate aggregates in 1928 and was followed by others, notably H. S. sweet,' B. Mather et al.,3 and K. Mather4 who emphasized the petrographic and physical aspects of carbonate aggregates. The recognition that certain carbonate aggregates are reactive in concrete has led to increased participation in research in the past few years by groups outside of Iowa. Significant contributions have been made by Swenson and Gillot,5 Hadley,6 and Chaiken and Halstead7 in work which emphasizes the expansion of carbonate rocks in alkaline environments and the reaction of carbonate minerals or dedolomitization with alkalies. It is the purpose of this paper to review briefly the nature and extent of the problem and present a summary of the research by the author and his associates. EXTENT AND NATURE OF THE PROBLEM The problem is the deleterious behavior of certain carbonate aggregates in concrete. It was first recognized in Iowa over 20 years ago when poor service records of certain highways were correlated with aggregates produced from the Glory and LeGrand quarries. Deleterious behavior of carbonate aggregates have been reported in Canada and, more recently, in New York and Virginia. As more knowledge is gained concerning the problem, distress in concrete related to carbonate aggregates may be recognized over a widespread area. The problem may potentially exist in the Midwest, the Northeast, and other parts of the country underlain by thick sections of carbonate rocks readily available for utilization as aggregates. The nature of distress in Iowa highways is a general weakening and deterioration of concrete characterized by progressive cracking and spalling away from joints and edges (Fig. 1). The distress generally occurs after 15 years of service and becomes progressively worse. Specimens of such concrete lack the toughness of sound concrete and break easily under the hammer in the manner of a soft brick. The matrix is generally highly carbonated and dark borders, or reaction shells or rims outline the argillaceous carbonate aggregate fragments (Fig. 2). Cracks observed in cores cut across the aggregates and concrete matrix. Although localized volume change (expansion) is associated with spalling, there is no definite field evidence in Iowa that excessive growth of concrete slabs has occurred. The experience with carbonate aggregates in Iowa indicates that the concrete deterioration is not the same as that induced by the alkali-aggregate reaction associated with siliceous aggregates. The principal difference is that in Iowa the distressed concrete is weakened throughout the slab. In concrete affected by the alkali aggregate reaction, the

Jan 1, 1961

By R. W. Hyde, S. E. Eaton, B. S. Old

One of the most important problems facing the steel industry at the present time is that of maintaining at a minimum the sulphur content of many grades of steel where sulphur is known to have harmful effects On both quality and yield. The present outlook in this struggle to reduce the amount of sulphur in steel is rather gloomy since the sulphur content of the raw materials available in the United States is gradually rising, with little relief in sight. A flow sheet of sulphur in the steel process is shown in Fig I. The values used here were obtained by averaging coke oven and blast furnace data at No. 5 furnace in Cleveland and are considered typical for high top pressure practice. The sulphur evolved in the blast furnace top gas was obtained by difference and since the amount is relatively small, little significance should be attached to this particular value. From Fig I it is apparent, however, that coals used in the production of metallurgical coke represent by far the largest single source of sulphur in steel-making. As an indication of the decrease in quality of these coals as regards sulphur content the weighed average annual sulphur analysis of the coals supplied to two different steel plants, since 1925, is plotted in Fig 2} The sharp rise since 1940 is strikingly apparent. Another indication of this trend is found in estimates of coking coal reserves. Thus in the case of Pittsburgh seam coals available in Allegheny, Fayette, Greene, Washington, and Westmoreland Counties in Pa. as of Jan. 1937 only 25 pct of the coal reserves would contain less than 1.50 pct sulphur after washing.2.3 Many of these lower sulphur reserves have been seriously depleted in recent years because of accelerated war demands. still another demonstration of the increasing sulphur content of coals on a country-wide basis is found in a report by the Bureau of Mines4 which shows a steady increase in the sulphur content of coke made in the United States. It should be noted that this increase continues in spite of the wider use of coal washing in recent years. Sulphur occurs in coal in three forms, pyritic (FeS2), organic sulphur, and a small amount of sulphate sulphur (CaS04). The sulphur is subsequently found in the coke in combination with carbonaceous material of is composition and as calcium and iron sulphides' In considering the general problem of sulphur elimination, the Republic Steel Corp. was interested in determining which, if either, of the two major forms of sulphur in coal contributes the greater portion of sulphur to the coke. Since the ratio of pyritic to organic sulphur varies widely in different coals, it was thought that if it could be shown definitely that the major part of the sulphur occurring in coke originates from one of the two ""jar forms of sulphur in the coal, it would then be possible to select with confidence coal which, although high .in total sulphur, would yield coke of fairly low sulphur content. Using the new

Jan 1, 1949

By A. P. Woods, J. A. Elias, A. J. Heckler

A method is described by whichX-ray pole figures and axis density figures may be plotted automatically. The X-ray data are obtained using a Siemens texture gonionleter and the Schulz reflection method. Composite sampling methods are used to obtain a full quadrant of the pole figure. The contour lines of the pole figure and axis density figures are drawn using a computer-controlled x-y plotter. The computer program used to draw the contours was obtained from ZBM. POLE figures used to describe crystallographic orientations of poly crystalline sheet materials are usually plotted manually from X-ray diffraction output in the form of a strip chart recording of the intensity distribution of a given crystallographic pole in physical space. Today's computers and associated plotting equipment now make it possible to plot pole figures and axis density figures automatically. Inverse pole figures have been determined by mathematically "inverting" X-ray pole figure data.'-' In general, these methods require complicated, time-consuming numerical calculations. A more economical but less accurate method is to determine the axis densities of low-index crystallographic poles using an X-ray diffractometer. When these axis densities are plotted in a unit stereographic triangle contour lines can be drawn to represent the axis density distribution. This can now be done automatically. Computers were used to plot pole figures by a method developed by Holland, Engler, and powers.' In their method intensity ratios based on a random standard sample were obtained from a strip chart recording, and the stereographic (x, y) coordinates of these ratios were determined by a computer. Symbols characteristic of different intensity ratio levels were then plotted using an automatic x, y plotter and intensity contours were drawn manually. The present paper describes a method by which pole figures and axis density figures have been automatically plotted from digital data obtained from a Siemens X-ray unit. Plotting was accomplished using an IBM 1620 computer and a Calcomp 563 digital plotter. COMPUTER PROGRAM The computer program was obtained from IBM Systems Reference Library, No. 1620-CS-05X, and was designed to plot contour maps from randomly distributed data. It consists of a set of twelve separate subprograms, four of which were used in this work. The program takes a given distribution of data points and by a numerical method determines the values at mesh points of a square grid system superimposed over the input data. The output data from this program is in a form suitable for input to the contour plotting program. A smoothing program is also available which calculates new mesh point values from a continuous function fitted to neighboring mesh points. The degree of smoothing depends on the number of points around a given grid point which are used to adjust or smooth the grid value. The contour plotting program is designed to allow the user to specify the interval, scale, and annotation of the contours to be plotted. EXPERIMENTAL PROCEDURE Pole Figure Data Points. Diffracted X-ray intensities were determined using a Siemens texture goniometer and the schulzs reflection method. Due to geometric

Jan 1, 1968

By R. W. Hyde, B. S. Old, S. E. Eaton

One of the most important problems facing the steel industry at the present time is that of maintaining at a minimum the sulphur content of many grades of steel where sulphur is known to have harmful effects On both quality and yield. The present outlook in this struggle to reduce the amount of sulphur in steel is rather gloomy since the sulphur content of the raw materials available in the United States is gradually rising, with little relief in sight. A flow sheet of sulphur in the steel process is shown in Fig I. The values used here were obtained by averaging coke oven and blast furnace data at No. 5 furnace in Cleveland and are considered typical for high top pressure practice. The sulphur evolved in the blast furnace top gas was obtained by difference and since the amount is relatively small, little significance should be attached to this particular value. From Fig I it is apparent, however, that coals used in the production of metallurgical coke represent by far the largest single source of sulphur in steel-making. As an indication of the decrease in quality of these coals as regards sulphur content the weighed average annual sulphur analysis of the coals supplied to two different steel plants, since 1925, is plotted in Fig 2} The sharp rise since 1940 is strikingly apparent. Another indication of this trend is found in estimates of coking coal reserves. Thus in the case of Pittsburgh seam coals available in Allegheny, Fayette, Greene, Washington, and Westmoreland Counties in Pa. as of Jan. 1937 only 25 pct of the coal reserves would contain less than 1.50 pct sulphur after washing.2.3 Many of these lower sulphur reserves have been seriously depleted in recent years because of accelerated war demands. still another demonstration of the increasing sulphur content of coals on a country-wide basis is found in a report by the Bureau of Mines4 which shows a steady increase in the sulphur content of coke made in the United States. It should be noted that this increase continues in spite of the wider use of coal washing in recent years. Sulphur occurs in coal in three forms, pyritic (FeS2), organic sulphur, and a small amount of sulphate sulphur (CaS04). The sulphur is subsequently found in the coke in combination with carbonaceous material of is composition and as calcium and iron sulphides' In considering the general problem of sulphur elimination, the Republic Steel Corp. was interested in determining which, if either, of the two major forms of sulphur in coal contributes the greater portion of sulphur to the coke. Since the ratio of pyritic to organic sulphur varies widely in different coals, it was thought that if it could be shown definitely that the major part of the sulphur occurring in coke originates from one of the two ""jar forms of sulphur in the coal, it would then be possible to select with confidence coal which, although high .in total sulphur, would yield coke of fairly low sulphur content. Using the new

Jan 1, 1949

Selected bibliographies of the Iron Resources of the World and the Coal Resources of the World have' been prepared by the Engineering Societies Library for the National Research Council from the most prominent. American, English and foreign books and periodicals. The bibliograpies are intended as a guide to the literature giving economic

Jan 5, 1919

By Eugene Guccione

Fear of inflation is one important reason for the rebirth of interest in the stock market, and natural resources are the best investment in an era of rapid inflation.

Jan 6, 1976

By M. van Swaay, C. E. Birchenall

A. S. lBrling (Johnson, Matthey & Co. Ltd., Laboratories)— Because of its initial emphasis upon the production of membranes by powder metallurgy and by normal casting and rolling techniques, this paper is of considerable interest to those concerned with the design and application of industrial diffusion units. As the subsequent performances of the three grades of palladium were not compared in detail, it can perhaps be concluded that specific permeabilities were very similar. A short table in which the absolute diffusion rates obtained by the Authors with their three grades of palladium were compared with those of other investigators18-25 would, however, have been of particular value in view of the very variable results obtained with this membrane material. The Authors state early in the paper that the permeability of the thoriated samples decreased in much the same way as that of the nonthoriated samples. Later, they emphasize that sintered palladium without thoria was very susceptible to poisoning and did not respond as well as the other materials to the decontamination treatment. These results, which suggest that sintered membranes are less effective than those produced by normal methods, have considerable industrial implications, and amplified experimental details would be very welcome. The results of the Authors differ in one important respect from those of other investigators. Thus, no "bleeding" was required to maintain a constant rate of diffusion, although Davis, Darling, and De Rosset found this to be necessary. Davisz3 found that "bleeding" was necessary even when the hydrogen had already been purified by diffusion through a palladium tube, and it would be of value to know the purity of the gas stream emerging from the purification train shown on Fig. 1 of the Authors' paper. The Authors show that diffusion rates varied according to the square root of the pressure difference providing that the palladium membrane was not contaminated in any way. This finding is in agreement with the results of those workers2,18,19,23,24 who diffused their hydrogen through the membrane into a partly or completely evacuated system.Those workers who did not find this square-root law dependence did not have a partial vacuum on the downstream-side of the membrane.'' The difference between the two experimental con- ditions appears to be significant, as the absolute diffusion rates per sq cm of diffusion area are lower when the square-root law dependence is not observed. While the effect could be attributable to poisoning of the membrane it is conceivable that a positive pressure on the downstream side of the membrane might influence the mechanism of diffusion. In view of the capricious behavior of palladium, factors of this type, which are likely to influence its industrial significance, should be carefully considered. M. van Swaay and C. E. Birchenall (authors' 9-eply) — Our Eq. 191 may be compared with several others for hydrogen diffusion in palladium: D = 5.95 x exp (-5770/1)' D = 3.55 x 10"3 exp (-5550/)' D = 4.3 x 10"3 exp (-5620/1')' Other values are given in the literature, but in many cases surface poisoning may have affected the results. No analysis was performed on the hydrogen gas stream after purification. It should be noted that the presence of liquid nitrogen traps near the heated membranes may have set up convection currents and provided the equivalent of "bleeding." The question of whether a partial vacuum existed on the downstream side of the membrane is not clear. Does it imply that there is something unique about the permeability measured near one atmosphere pressure? We do not believe that there is. When square root pressure dependence is not observed, diffusion rates are not measured. Is "absolute diffusion rate per sq. cm. of diffusion area" equivalent to permeability? The terminology is new to us. In any case we doubt very much that pressures of the order of several atmospheres can affect the mechanism of diffusion.

Jan 1, 1962

By Oscar Weiss

STILFONTEIN and surrounding areas gave nega-tive results in all prospecting attempts since about 1904 when Goerz and Co., a forerunner of Union Corporation Ltd., first drilled in the region and on the farm Stilfontein. Subsequent efforts by African and European Investments Co. and Anglo American Corp. from 1934-37 were completely unsuccessful. Holes drilled by these companies on the farms Riet-fontein, Hessie, and Palmietfontein were stopped in the Lower Witwatersrand system without finding payable reefs. The results of gravimeter, ground magnetometer, and aerial magnetometer surveys are presented in the area, in and around the new Stilfontein Gold Mine, in the Klerksdorp District of the Transvaal in the Union of South Africa. The gravimeter and ground magnetic surveys were completed in 1947—48. The gravity anomalies suggested a block of Upper Witwatersrand quartzites faulted-up between denser rocks of dolomite and Ventersdorp lava. Boreholes S.T. 1, 2, and 3 were drilled in 1948 and, after penetrating the dolomite and Ventersdorp lava, entered Upper Witwatersrand quartzites and intersected the Gold Estates Reef and Vaal Reef. Subsequent drilling delineated the suboutcrop of the Vaal Reef and determined the main structure of this horizon. The gold content of the Vaal Reef was highly payable and shaft sinking is now in progress. The Stilfontein Gold Mining Co. has been formed and, up to date, f5,000,000 capital has been raised for plant, shaft sinking, and development. The payable Vaal Reef horizon extends further south from Stilfontein, the reef occurring at increasing depths. It is possible that at least another mine may be established on these deeper horizons. The farm Stilfontein 39 is situated in the Klerksdorp District of the Transvaal. This farm and the surrounding areas have been subjected to repeated programs of prospecting dating back to about 1904, when Goerz and Co., the forerunner of Union Corporation, Ltd., first drilled on the farm and in the surrounding areas. From 1934-37, numerous boreholes were drilled on the neighboring farms, Riet-fontein. Hessie. and Palmietfontein, by African and European Investment Co. and Anglo American Corp. All these efforts were completely unsuccessful, and nobody suspected any possible gold-bearing area on Stilfontein until about 1947, when a gravity traverse run by B. D. Maree on the main road, showed a negative gravity anomaly. During 1947-48, the writer's organization completed gravimeter and magnetic surveys on Stilfontein and Rieffontein. An area of negative gravity anomalies was mapped, and it was suggested that this could be caused by blocks of Upper Witwatersrand quartzites, of the average density of 2.65, faulted up between dolomites and Ventersdorp lavas, the density of both of these rocks being 2.8. Fig. 1 shows the geology of the area as mapped by L. T. Nel of the Geological Survey of South Africa. The boreholes on Stilfontein, with the exception of a single hole of Goerz and Co., were drilled after the completion of the geophysical survey. The grouping of the first boreholes S.T. 1, 2, 3, 4, 5, and 6, clearly shows that these were located in the zone of negative gravity anomalies. Fig. 2 shows the gravity anomaly contours. Fig. 3 shows two sections across the gravity anomaly, together with the corresponding geological sections as obtained from boreholes. The close relation between gravity values and thickness of dolomite plus Ventersdorp lavas is striking. The two latter formations having the same density (2.8), act as one mass as far as gravity effects are concerned. Fig. 4 shows the magnetic anomalies observed on the ground by vertical magnetometers and at 500 ft abbve mean ground level by aerial magnetometer. The latter are anomalies of the total magnetic intensity. The magnetic results show that, on the farm Rietfontein and on the northern half of Stilfontein. Lower Witwatersrand magnetic shales were to be expected at relatively shallow depths. As the strongly

Jan 1, 1952

By L. C. Brown, A. J. Stewart

Phase transformations have been studied in Ag-Zn alloys quenched from the high-temperature bcc 0 phase and lying in the composition range 37.4 to 50.0 at. pct Zn. On quenching, the alloy with the lowest zinc content transformed to massive a (fcc); all other alloys formed the ordered (3' phase. On deformation, a martensitic reaction took place forming a close-packed structure. At Lou' zinc contents transformation to this structure was complete. However, above 43 at. pct Zn a p.rogressively increasing amount of ß' was retained following deformation. The close-packed structure was fcc at lower zinc contents (under 47 at. pct Zn) and either hcp or a mixture of fcc and hcp at high zinc concentrations. The structures produced by cold working were unstable and on aging transformed to the ß' phase or the complex hexagonal to phase. For low zinc contents (under 43 at. pct) the fcc st-ructure transformed directly to the equilibrium To phase. With higher zinc contents, some 13' was retained following defownation, and on aging the amount of this phase relative to the close-packed structure increased. On further aging both structures transformed cornpletely to PO. Metallographic examination indicated that the nature of the deformation product depended very markedly on the mode of deformation. Tensile deformation gave a microstructure characteristic of thermal martensite. KING and Massalski1 have shown that an alloy of Ag-50 at. pct Zn quenched from the high-temperature bcc ß phase undergoes a low-temperature ordering reaction forming ß' which can be retained to room temperature. On deformation an hcp phase is produced, although this is unstable and the structure reverts completely to ß' on aging. In the present paper, the work of King and Massalski is extended to cover a wide composition range in the p phase, observations being made of the structure of the quenched 13 and of the effects of deformation and aging. The relevant portion of the Ag-Zn phase diagram is shown in Fig. 1. King and Massalski have shown that close to stoichiometry the ß' phase is the equilibrium structure at low temperatures. The approximate composition range of this phase, taken from a recent paper by Pops and Massalski,3 is shown on the phase diagram. The locations of atom sites are very similar in the ß' and to structures, and the 4, structure can be derived from the 0' structure by a small movement of atoms mainly in the direction of the cube diagonal.4'5 However, the probability of filling any particular atom site by a silver or a zinc atom is markedly different in the two structures. The structure can be considered partly ordered but the arrangement of the ordered atoms is completely different from that in the p' structure and transformation from ß' to requires a large fraction of the atoms to change position. It has been shown that the ß' transformation is thermally activated involving normal nucleation and growth processes.5,8 Massalski and Barrett7 have shown that in the Cu-Zn binary the (3 phase can be retained in the ordered state to room temperature over a wide composition range. On deformation a new close-packed phase is produced, the structure varying from fcc to a mixture of fcc + hcp to hcp alone with increasing zinc concentration. It appears that an ordering reaction is necessary to retain the bcc phase to room temperature. In CU-Ga,8 the bcc phase cannot be retained to low temperatures as it transforms by a massive reaction above the ordering temperature of the ß phase. The structure of the massive phase is very similar to that in Cu-Zn, varying from fcc to fcc + hcp to hcp with increasing zinc concentration. Similar structures have also been observed in CU-A1,9 Ag-Cd,10,11 and Ag-Al.12 EXPERIMENTAL The alloys were prepared by melting fine silver (99.99 pct purity) and electrolytic zinc (99.999 pct

Jan 1, 1969

By Andrew S. McCraeath

The treatment which a steel receives, and the uses to which it may be applied, are frequently determined by the percentage of carbon which it contains; and especially is this the case in the different steel works in this country. The part which this element plays in the composition of steel is such an important one that a process for its accurate determination becomes an absolute necessity.

By T. Saburi, C. M. Wayman

The massive and martensitic transformations in ß Cu-Ga alloys were studied by optical microscopy and by transmission electron microscopy and diffraction. These types of transformation are distinct and do not merge into one another. An internal fine structure due to stacking faults was found in both the massive phase (m) and the martensite, but the origin of the faults is believed to be different in each case. The faults in the martensite are due to the lattice invariant or "second" shear of the phenom-enological theory, while those in the are probably growth faults and deformation faults arising from the transformation volume change. Evidence is presented for ordering in the ß phase prior to transformation into martensite, and the crystal structures of and ß' and ßi martensites are discussed. THE results from some previous investigations1,2 have led to the suggestion that martensitic and massive transformations have certain common characteristics. It presently seems established that massive transformations like martensitic transformations are essentially diffusionless,1,2 but unlike martensitic transformations, when a new phase forms massively there is no shape change or surface relief.= If the massive-type transformation is crystallographically similar to martensitic transformations, one would expect a fine structure as a result of the lattice invariant shear4 which is a part of the transformation mechanism. The existence of such a fine structure (i.e., slip, twinning, or faulting), if any, can be verified by transmission electron microscopy, and thus the present investigation was undertaken to compare the internal structure of massively and martensitically formed phases in Cu-Ga alloys which were derived from a parent of the same composition. The transformation characteristics of ß Cu-Ga alloys were also studied. The bcc ß phase in the Cu-Ga system, Fig. 1, is stable above 616oc.' Depending upon the cooling rate, ß Cu-Ga alloys can undergo three different types of phase transformations. The ß phase of eutectoid composition (23.7 at. pct Ga) decomposes into the ? phase (hcp) and the phase (complex cubic) by means of a eutectoid reaction. When the cooling rate is increased so that the decomposition of 0 into [ and ? is suppressed, the ß phase transforms into a nonequilibrium hcp phase, herein denoted ?m by a process of very rapid growth called a "massive" transformation. At even faster quenching rates the massive transformation can be suppressed and the ß transforms martensitically. Massive transformations, apparently similar to those in the Cu-Ga system, have also been studied in the Cu-Zn2,6-8 and Ag-Cd systems.9 Definitive characteristics if the Massive Transformations in 0 Cu-Ga Alloys1 1) The most remarkable feature of the massive transformation in Cu-Ga is that there is no bulk composition change on transformation. According to Massalski,1 the resulting [, phase is a supersaturated extension of the equilibrium [ phase. The lattice parameters continue the trend exhibited

Jan 1, 1965

By J. E. Hanafee, G. J. London

MANY studies of the deformation behavior of materials under a superimposed hydrostatic pressure have shown that materials brittle at ambient pressure behave in a ductile manner under pressure. Thus, with a metal such as beryllium which possesses relatively low ductility, but otherwise exhibits quite useful physical and mechanical properties, hydrostatic pressure may be particularly useful for both forming beryllium shapes and studying its deformation behavior. In fact, it has been found1"4 that polycrystal-line beryllium in both ingot and powder form appears to behave in a more ductile manner on a macroscopic level in a hydrostatic pressure environment, and it has been suggested2 that this is due to activating a new slip mode. Furthermore, Andrews and Radcliffe5 have found pressure induced nonbasal dislocation activity in hot pressed beryllium. Recently6 it has been shown in "c-axis" compression tests under hydro-static pressures up to 28 kbars that the shear stress needed to cause slip with a Burgers vector out of the basal plane (pyramidal slip) does not change with increasing pressure in beryllium with a purity of some 99.5 pct. This material is equivalent or more pure than the beryllium used in the previous pressure studies. Thus, it appears, as suggested by Inoue et al.,3 that the hydrostatic pressure affects the fracture stress rather than the stress necessary to activate pyramidal slip in beryllium. However, in "c-axis" pressure tests on high purity 12 zone pass beryllium (˜50 ppm total impurities) the macroscopic compression stress needed to cause pyramidal slip was considerably lower than that at ambient pressure.6 It has further been shown that alloying beryllium with nickel and copper in the range 2-5 wt pct also favors the occurrence of pyramidal slip in "c-axis" compression tests,7'8 while lower amounts of nickel and copper do not have significant effects. In the present study the combined effect of hydrostatic pressure and alloying high purity beryllium on the shear stress needed to cause pyramidal slip has been ascertained. A 2.5 wt pct Cu alloy was selected as the first alloy to study as this level of copper did favor pyramidal slip at room pressure. A high purity (12 zone pass) single crystal of beryllium 0.3 by 0.1 by 0.1 in. was cut and polished by an orientation and lapping technique8 so that the top and bottom compression surfaces were parallel and within 3 min of arc to the (0001) plane and the sides parallel to the {l010} and {ll20} planes. In these compression specimens, therefore, the resolved shear stress was nearly zero on both the basal and prism planes, and slip was restricted to pyramidal systems. Analysis of slip traces on the two lateral surfaces served to accurately identify the active slip planes.6'9 The pressure unit was a modified piston-cylinder device fitted with a manganin transducer coil arrangement which continuously monitored and recorded the hydro-static pressure. The load on the specimen was measured by a strain gage load cell which operated entirely within the pressure chamber. This load cell was calibrated before and after each pressure cycle at room pressure in situ and the calibration did not vary more than ±1 pet. These techniques and devices have been previously described in more detail.6 Successively higher compressive stresses were applied to the single crystal under a superimposed hydrostatic pressure until fracture occurred. The strain rate was (4.5 ± 2.0) x 10-6 sec-1 and the average rate of pressure application and release was approximately 0.3 kbars per min. As the load on the specimen was applied by the piston which was used to increase the hydrostatic pressure, the pressure increased during the compression test. This increase ranged from 0.0 to 0.8 kbars, and the maximum hydrostatic pressures are quoted in Fig. 1. The lateral surfaces of the specimen were examined in a light microscope after each pressurization/stress cycle so that the stress at the onset of {1122} pyramidal slip could be ascertained. Post compression height measurements allowed the plastic strain in the specimen to be evaluated to within 0.03 pct. The resulting compression stress-plastic strain curve is shown in Fig. 1 with results of a "c-axis" test on a similar Be-2.5 wt pct Cu single

Jan 1, 1970

Map

Jan 1, 1960

By T. D. Ledyard

SIR WILLIAM LOGAN, our great geologist, predicted that Canada would become eventually one of the greatest iron-producing countries of the world. Although possessed of numberless deposits of iron-ore, we have not yet done much to verify this prediction. Causes can be found for our backwardness, the principal one being

Jan 1, 1891

By Eckley B. Coxe

In making surveys in the anthracite coal regions of Pennsylvania, the ordinary engineer's chain (50 or 100 feet long) is generally used, both above and below ground. Sometimes, where it is difficult to chain, as, for instance, across a chasm, a wire is stretched from one station to the other, the distance is marked on the wire and its length is then measured with the ordinary chain. Having had occasion lately to make some surveys where it was necessary to determine with great accuracy the position of the land or property line, not

By Henry A. Gordon

Under the title " Hysteromorphous" it is proposed to include deposits which have been formed from original deposits by the influences of the surface-region. The term Hysteromorphous—later-formed—has been used by Prof. Posepny, of Vienna, to distinguish secondary from primary deposits and is more comprehensively applicable than the terms or designations hitherto used for the same thing.

Jan 1, 1896