Search Documents

By van Wert, L. Russell

During an investigation in which the solubility relations of the phases in Muntz metal (60 per cent. copper, 40 per cent. zinc) were under study, certain phenomena that had no immediate connection with the main problem were observed, which were thought sufficiently interesting to study further. Because of lack of time, only a preliminary survey was made of two of these; namely, the cleavage structure developed under certain conditions in a 60:40 brass and abnormal grain growth in this alloy. Cleavage Structure in Heat-treated Muntz Metal Carpenter noted many years ago that cold-working a brass of the Muntz metal type, which had been quenched previously from within the beta field, results in a partial breakdown of the supersaturated beta solution and the precipitation of the solute (the alpha solution) in the cleavage planes of the beta grains. This manner of rejection of a solute from a metastable solid solution is not peculiar to this particular alloy, for among others, it occurs in the cold-working of certain austenitic steels; for example, the austenitic nickel steels. In these ferrous alloys, cold deformation produces a partial decornposition of the austenite, with the formation of martensitic "needles" and zigzags in the austenitic poly-hedra. It is interesting to note that while the two solid solutions— austenite and quenched Muntz metal— are metastable and in their mode of decomposition behave quite alike when deformed in the cold, the metastability of each results from a different cause; viz., that of the austenite from the fact that it is a supercooled solution (its solvent. gamma iron, at ordinary temperatures is below its normal stable range whereas the metastability of the quenched Muntz metal is the result of supersaturation. When a 60:40 brass is quenched from above 800" C.—that is, from within the field where the beta phase alone is stable—this solution is retained practically intact and the alloy so cooled is found to consist almost entirely of polyhedra of this solution with only a little alpha present ordinarily at the boundaries of the beta grains—the result of a slight

Jan 1, 1929

By T. Johnston, B. Cox

The results of oxidation and corrosion experiments on niobium in oxygen and steam at temperatures of 350° to 650°C, and in dilute sulphate solutions at 300°C are presented. The oxidation of niobium in oxygen can be explained in terms of a pre-transition period, which obeys an approximately parabolic rate law, and a post-transition period in which a more rapid linear rate is partially stifled by restriction of the gas flow due to the gvowth of the porous outer film. Due to changes in the porosity of the outer layers the restriction presented by the porous outel. film attains a limiting value. Subsequent oxidation obeys a linear rate law and shows an almost linear dependence of the rate on gas pressure. liltimately a second failure of the protective film may take place leading to a further acceleration in the oxidation rate. In water vapor the oxidation of niobium follows a parabolic rate law and does not show a transition to linear kinetics. The higher oxide, Nba05, was usually absent from the NbO/NbO2 film which was formed. The addition of a small partial pressure of oxygen to the water vapo3, resulted in accelerated oxidation according to the normal kinetics for oxidation in oxygen. The oxygen reacted preferentially with the niobium, and the protective oxide film was reformed when all the oxygen had been consumed. This behavior supports the theory that nucleation of Nb205 on the surface of the protective NbO/NbO2 film is the cause of the accelerated oxidation. After oxidation in steam at high-pressure Nb2Os was found in the protective film. The mode of formation of Nb2O5 under these conditions did not produce a change in kinetics, but was thought to explain the comparatively large dependence on pressure of the oxidation rate. The kinetics of oxidation in oxygenated aqueous solutions at 300°C were similar to those for oxidation in oxygen. A penetrating attack on niobium sheet may be related to the second breakaway observed by some investigators of oxidation in oxygen.

Jan 1, 1963

By AIME AIME

TOTAL shipments of iron ore from the Lake Superior district totalled 21,672,410 long tons in 1933, according to a compilation in Skillings' Mining Review. The producers ranked as follows in order of output shipped:

Jan 1, 1934

By J. R. Stack, H. H. Alexander

Prior to 1915, numerous attempts were made to treat tin concentrates in the United States, but for various reasons they were unsuccessful. Tin ore is said to have been found in nearly every state, but none of the deposits has proved to be of commercial importance. An annual output of a few hundred tons in Alaska is the only domestic production; hence any considerable production of tin in the United States must be from foreign ores. The most promising occurrence of tin was found in the Black Hills, S. Dak.; in the early development stage, it was called the Cornwall of America. Associated with the tin is tungsten The story is told that an exceedingly fine specimen of the Black Hills ore was sent to England to encourage stock promotion; the desired effect was produced until a skeptic chipped off a small piece, which the analysis showed to be wolframite. First Attempts at Smelting One of the first promising attempts at tin smelting in the United States was made by R. T. White at Bayonne, N. J., in 1903. Mr. White, after spending some time in England studying the methods of tin smelting, organized a company called the International Tin Co., and erected a plant to treat tin concentrates from the Straits of Malacca. About the time the plant was completed, the English Government placed an export duty of 40 per cent. ad valorem on tin concentrates exported to other than British smelters, which duty made it impossible to operate this plant so the enterprise was abandoned, As this export duty is still effective, the only source of tin-ore supply for the United States is the Bolivian concentrates. Bolivian Tin Concentrates Unlike the alluvial placer deposits, nearly all Bolivian tin occurs in lode deposits and some of the highest grade ores contain only a small

Jan 1, 1924

By Henry S. Rawdon

The relation between the course, or path, of the fracture of metals and alloys, produced in service or as a result of certain laboratory tests, and the crystalline units of which such materials are composed is of utmost importance. The fracture of normal material is, in general, intracrystalline, i.e., it consists of a break across the grains rather than of a separation between them. An interorystalline fracture indicates either that the metal is of very inferior quality or that the break occurred under very unusual conditions, e.g., at a very high temperature. The usual mechanical tests, when applied to metals of the type that breaks with an intercrystalline fracture, merely measure the coherence of adjacent grains for one another and reveal little as to the real properties of the metal itself. Even such a soft plastic substance as lead, under suitable conditions, may be rendered so weak and brittle that the metal can be easily crumbled into powder by the fingers although the constituent grains have lost none of the intrinsic properties of lead. Various erroneous explanations of this behavior of lead have appeared in the scientific literature, the change being described usually as an allotropic one. The importance, in an industrial sense, of a proper explanation of this type of the corrosion of lead justifies the description of the type of metal deterioration that follows. Corroded Lead Sheathing In Figs. 1 and 2 are shown two typical specimens of corroded lead sheathing selected from materials submitted to the Bureau of Standards for examination. Fig; 1 shows a section of the sheathing of an aerial cable; Fig. 2, that of the lead covering of a subterranean feeder-line of an electric light system. In this case the deterioration had proceeded to a much great'er extent than in the case shown in Fig. 1 so that certain portions of the metal could easily be crumbled into a coarse gray powder by the fingers. This was particularly true of those portions of the sheathing

Jan 1, 1921

By Henry M. Howe

The striking features of American Bessemer practice aré its large output and its low initial silicon and initial temperature. These are interdependent. Large outputs implies short blows and short intervals between blows. Short blows imply low silicon and fast blowing. Low silicon implies short intervals and fast blowing. Our blows are short because we have little silicon to remove, and because we remove it fast by supplying blast rapidly. We get enough heat even with little silicon, because our blows and the intervals between them are so short that relatively little heat escapes from our vessels. Were we to lengthen our intervals, or to blow more slowly, we would have to meet the increased loss of heat from our vessels, either by using more silicon, or by melting hotter, i.e., by burning more coke, in the blast-furnace or in the cupola. Finally, our short intervals imply powerful machinery, efficient organization, and extreme specialization and subdivision of labor, which can be profitable only when the output is large. Let, us now take these points up in more detail, first glancing at some examples of our large outputs, given in Table I., and of the composition of our iron. Output.—On presenting such results to some foreign metallurgists, I have been told, " Oh yes, we quite understand that. You really turn out no more steel than we do. As a matter of personal pride, your manager gets up a tremendous spurt for a day, or even a week, crowds on men wastefully, rushes through great quantities of metal, and then for months afterwards has to recuperate. The machinery has been strained ; the owner's money has been wasted ; the men have been prostrated—all to gratify the manager's vanity. Your average output is no larger than ours." Personal pride has, doubtless, played its part; without it we would still be savages, or apes, or mollusks, if you prefer. These baser motives are the mudsills of progress, the soiled roots of that growth of which civilization is the flower. Great outputs were made

Jan 1, 1891

By A. S. Richardson

THe conditions that make necessary the mechanical ventilation of the Butte mines of the Anaconda Copper Mining Go. are due to a number of causes, all of which are incidental to the depth at which mining operations are now carried on, The main object to be accomplished, of course, is the reduction of the temperature and humidity of the air in the working places. Ventilation fans, both surface and underground, have been used for many years, but increasing depth has made the problem much more difficult. Further improvement in both ventilation equipment and methods, therefore, became necessary; and it is the purpose of this paper to describe the work planned and done under the improvement program. The mines of the district have been frequently described in various technical publications, so a description is unnecessary here. From a mine-ventilation viewpoint, compared with coal-mine ventilation systems, the problem is complicated by the fact that the workings to be ventilated are situated on a large number of steeply dipping veins which frequently intersect and are faulted, and also by the fact that the extent, or existence, of orebodies is not definitely known in advance of actual development work. For these reasons ventilation work cannot be planned in advance of actual operations, nor can such regular systems of ventilation as are used in working the more uniform and continuous bodies of coal be developed. When operations are conducted at a normal rate, about 10,000 miners are employed on two shifts, so that about 5000 men will be underground at one time. But as ventilation is necessary to reduce high temperature and humidity due, mainly, to natural causes, the quantity of air per man per minute is not a governing consideration in determining ventilation requirements. Most important among the numerous sources of heat and humidity in the mines are: heat generated during decay of mine timber; heat and humidity given off by mine rock and water; heat generated by oxidation of sulfide minerals; heat given off by electrical equipment; heat generated by mine fires (in certain localities).

Jan 1, 1923

By A. S. Richardson

THe conditions that make necessary the mechanical ventilation of the Butte mines of the Anaconda Copper Mining Go. are due to a number of causes, all of which are incidental to the depth at which mining operations are now carried on, The main object to be accomplished, of course, is the reduction of the temperature and humidity of the air in the working places. Ventilation fans, both surface and underground, have been used for many years, but increasing depth has made the problem much more difficult. Further improvement in both ventilation equipment and methods, therefore, became necessary; and it is the purpose of this paper to describe the work planned and done under the improvement program. The mines of the district have been frequently described in various technical publications, so a description is unnecessary here. From a mine-ventilation viewpoint, compared with coal-mine ventilation systems, the problem is complicated by the fact that the workings to be ventilated are situated on a large number of steeply dipping veins which frequently intersect and are faulted, and also by the fact that the extent, or existence, of orebodies is not definitely known in advance of actual development work. For these reasons ventilation work cannot be planned in advance of actual operations, nor can such regular systems of ventilation as are used in working the more uniform and continuous bodies of coal be developed. When operations are conducted at a normal rate, about 10,000 miners are employed on two shifts, so that about 5000 men will be underground at one time. But as ventilation is necessary to reduce high temperature and humidity due, mainly, to natural causes, the quantity of air per man per minute is not a governing consideration in determining ventilation requirements. Most important among the numerous sources of heat and humidity in the mines are: heat generated during decay of mine timber; heat and humidity given off by mine rock and water; heat generated by oxidation of sulfide minerals; heat given off by electrical equipment; heat generated by mine fires (in certain localities).

Jan 1, 1923

By J. Sharshall Grasty, Thomas L. Watson

The users of barite in the United States derive their supply partly from the domestic production and partly from the imports from foreign countries. According to the Mineral Resource division of the U. S. Geological Survey, the domestic production of barite in 1913 was 45,298 short tons, valued at $156,275, or $3.45 a ton, and the imports of crude barite were 35,840 short tons, valued at $61,409, or $1.71 a ton. These figures clearly show a decided advantage in cost of the foreign over the domestic barite to users in the United States. The difference in cost is the only advantage to the consumer of foreign barite, for there are large reserves of the mineral in the United States of good grade. The production of many of the operating mines is capable of decided increase, and it is believed that the operating mines together with the large reserves of undeveloped deposits of barite are entirely adequate to meet the demands of the users in the United States. Deposits of barite are known in California, Idaho, Nevada, and Alaska, but most of them are undeveloped because there is, apparently, no market for the material in that region. The domestic production is derived from Missouri .and the Appalachian States, the greater part being obtained from Missouri. Following the outbreak of war in Europe many users of foreign barite in the United States have been forced to seek their supplies at home. It seems opportune at this time, therefore, that a general review be given of the barite industry in the Appalachian States, one of the two areas from which the domestic supply of the mineral is derived, and that attention be directed to the undeveloped deposits in the region. Briefly, then, this paper reviews the barite industry in the Appalachian States, and describes the occurrence, preparation, and uses of the mineral. General Character Barite, known commercially as barytes or heavy spar, is barium sulphate (Baso4), containing when pure BaO, 65.7 per cent., and S03, 34.3 per cent. The specific gravity is 4.3 to 4.6, and the hardness 2.5

Jan 1, 1915

By W. R. Bean

Probably few, if any, of the many serious problems confronting malleable foundries have been more difficult of solution than the question as to why malleable that is ductile, black in fracture, and normal in all respects before galvanizing should, by that process, be rendered brittle, brilliantly crystalline or "white" in fracture, and of low resistance to shock. So far as we are aware, the technical literature contains no data or discussions on this subject, except two referencesl,2 of a general character. It is apparently a question that every one concerned, producer and consumer alike, has been willing to evade as far as possible. Various theories as to the cause of the deterioration have been given but such checking of these theories as we have done indicates that there was no sound basis for most of them. This work on the galvanizing of malleable was first undertaken in 1916, and has continued until the present time. We now feel that for all practical purposes we have reached a solution and are glad to be able to offer it in a form that can be readily applied to production processes. It is impossible to give here a detailed account of the early work done on this problem. A great number of tests were instituted and an enor-

Jan 1, 1923

By W. R. Bean

Probably few, if any, of the many serious problems confronting malleable foundries have been more difficult of solution than the question as to why malleable that is ductile, black in fracture, and normal in all respects before galvanizing should, by that process, be rendered brittle, brilliantly crystalline or "white" in fracture, and of low resistance to shock. So far as we are aware, the technical literature contains no data or discussions on this subject, except two referencesl,2 of a general character. It is apparently a question that every one concerned, producer and consumer alike, has been willing to evade as far as possible. Various theories as to the cause of the deterioration have been given but such checking of these theories as we have done indicates that there was no sound basis for most of them. This work on the galvanizing of malleable was first undertaken in 1916, and has continued until the present time. We now feel that for all practical purposes we have reached a solution and are glad to be able to offer it in a form that can be readily applied to production processes. It is impossible to give here a detailed account of the early work done on this problem. A great number of tests were instituted and an enor-

Jan 1, 1923

By J. E. Johnson

Discussion of the paper of Mark A. Amnion, presented at the Cleveland meeting October, 1913, and printed in Bulletin No. 70, October, 1913, pp. 1167 to 1 79. J. E. JOHNSON, JR., Ashland, Wis.:-Mr. Amnion's paper is of great value and it is not with any desire to reflect. on it that I wish to make some comments on the use of the scleroscope. We obtained one on trial some months ago and made very extensive tests with it, but without getting very satisfactory results. The readings on good car-wheels and bad ones were just about the same, but the factor in its use most likely to produce erroneous results is a variation in the thickness of the specimen being tested. In order to find out something on this subject we cut a thin disk, about -1,: in. thick, off a brass rod; then one 0.25 in. thick, and another about 1 in. thick, put the surfaces of all in about the same condition and tested them with the scleroscope. The readings varied widely; the resilience of the anvil evidently entered to a very high degree on thin pieces. By putting a soft cushion between such a thin specimen and the anvil, and forcing it up against the tube, the softness of the cushion cut off the resilience of the anvil and the results were more like those of the thick specimens. After a thickness of 1 in. was passed, the specimen seemed to have mass enough so that the resilience of the anvil no longer played an important part, and above that thickness results on different materials would be comparable, even though the thicknesses differed. But in order to get comparable results on thin specimens the thickness of those being tested should be the same. I should like to ask how the variations introduced in this way were overcome, so as to get strictly comparable results. Mr. AMMON :-.I have not had much experience in that, but the scleroscope is simply an indication of the surface harden-

Dec 1, 1912

By R.J. Anderson

Roughly, a crack in a casting may be considered, for the moment, to be due to fracture of the alloy resulting from the stress set up by the contraction in volume on passing from the liquid to the solid state. Cracks may be external or surface, internal or deep-seated, or incipient or so-called strain cracks. Draws may appear as depressions, unevenness, and "pinching in" of the surface of a casting. Roughly, draws are due to contraction in volume and are governed largely by the same factors as cracks. A casting may be cracked, however, without being drawn. Shrinkage is a foundry term and refers to the contractio~l in volume of a metal or alloy on passing from the liquid to the solid state. Patternmaker's shrinkage is the total contraction in volume (including liquid, solidification, and solid shrinkage) that occurs when an alloy is poured into a mold. The contraction in volume of aluminum is one of the principal factors affecting the occurrence of cracks, as will be shown later, and the question of shrinkage and its control requires careful study in any treatment of cracking in castings. In the case of sand and die castings, cracks have been attributed to a number of causes, but in the case of most light aluminum alloys, they are due to the large contraction in volume on freezing and the lack of its regulation or control. The most important factors are: (1) Contraction in volume; (2) composition of alloy; (3) quality of melting charge; (4) design of casting; (5) method of molding; (6) hardness of ramming; (7) method of gating; (8) hardness and characteristics of cores; (9) chills; (10) risers; (11) melting temperatures; (12) furnace used for melting; (13) pouring temperatures; (14) inclusions in alloys; (15) hot shortness of alloys; and (16) physical properties of alloys at high temperatures. Of these, the first, second, third, and eleventh to sixteenth involve ascertainable metallurgical facts; the remainder are largely matters of opinion, judgment, and technical knowledge of men experienced in the production of castings.

Jan 1, 1923

By R. J. Anderson

Roughly, a crack in a casting may be considered, for the moment, to be due to fracture of the alloy resulting from the stress set up by the contraction in volume on passing from the liquid to the solid state. Cracks may be external or surface, internal or deep-seated, or incipient or so-called strain cracks. Draws may appear as depressions, unevenness, and "pinching in" of the surface of a casting. Roughly, draws are due to contraction in volume and are governed largely by the same factors as cracks. A casting may be cracked, however, without being drawn. Shrinkage is a foundry term and refers to the contractio~l in volume of a metal or alloy on passing from the liquid to the solid state. Patternmaker's shrinkage is the total contraction in volume (including liquid, solidification, and solid shrinkage) that occurs when an alloy is poured into a mold. The contraction in volume of aluminum is one of the principal factors affecting the occurrence of cracks, as will be shown later, and the question of shrinkage and its control requires careful study in any treatment of cracking in castings. In the case of sand and die castings, cracks have been attributed to a number of causes, but in the case of most light aluminum alloys, they are due to the large contraction in volume on freezing and the lack of its regulation or control. The most important factors are: (1) Contraction in volume; (2) composition of alloy; (3) quality of melting charge; (4) design of casting; (5) method of molding; (6) hardness of ramming; (7) method of gating; (8) hardness and characteristics of cores; (9) chills; (10) risers; (11) melting temperatures; (12) furnace used for melting; (13) pouring temperatures; (14) inclusions in alloys; (15) hot shortness of alloys; and (16) physical properties of alloys at high temperatures. Of these, the first, second, third, and eleventh to sixteenth involve ascertainable metallurgical facts; the remainder are largely matters of opinion, judgment, and technical knowledge of men experienced in the production of castings.

Jan 1, 1923

By M. G. Corson

The iron-silicon alloy series has always been one of the most puzzling among the binary alloys. Examining the well-known mechanical properties of the iron-rich alloys only we meet the following situation: The ultimate strength and yield point of alloys worked and annealed under the usual conditions represent nearly a straight line function of the silicon content up to 1.5 per cent. silicon (Fig. I). Starting at the ultimate strength of 35,000 lb. and at a yield point of 16,000 lb. for pure electrolytic iron, one reaches a maximurn strength of 93,000 lb. and a maximum yield point of 74,000 lb. at 4.5 per cent. silicon. This corresponds to an increase in ultimate strength by 13,000 lb, per each per cent. of silicon added and nearly the same rate applies to the yield point. The data mentioned are taken from the investigation by T. D. Yensen,1 and while they do not exactly corroborate the results obtained by earlier investigators, they seem to be the most correct. Plastic properties of the alloys are controlled by a much more complicated relationship. Up to 2..5 per cent. Si, the elongation stays close to 50 per cent. (in 2 in.) and the area reduction amounts to 85 per cent., a situation that forms the usual feature of all alloys representing strictly solid solutions. The plasticity of the latter is always nearly equal to that of their base metal. Beyond 2.5 per cent. silicon, the situation becomes much more complicated. Yensen observed an enormous drop in elongation and area reduction at about 2.65 per cent. silicon, where the first hardly reaches 10 per cent. and the second is still lower; he found, however, a considerable recovery in plasticity at about 2.8 per cent. Si and up to 1.5 per cent. Si it is represented by 20 per cent. for the elongation and 30 per cent. for area reduction. Yensen's graphs, as shown in Fig. 1, indicate also a considerable drop in strength and yield point at the same point of 2.65 per cent. Si,

By Howard Scott, Henry S. Rawdon

The method of demonstrating the structure existing in a metal or alloy at high temperatures, by etching a polished sample after it has been heated to the desired temperature, is quite familiar to metallog-raphists. The usual procedure1 2 is to heat the specimen, previously polished for microscopic examination, to the desired temperature, in a neutral atmosphere (hydrogen or nitrogen), then admit the etching gas (chlorine, hydrochloric acid or similar gas) for a few seconds, and finally, after flushing out the etching gas with the neutral one, cool the specimen in the neutral atmosphere. The pattern produced by etching at a definite temperature is usually taken as a record of the microstructure prevailing at that temperature. It has frequently been pointed out that changes in composition of the surface metal occur during the preliminary heating in the neutral atmosphere, so that the appearance produced by the etching at high temperature may not exactly represent the condition of the interior of the specimen. To overcome this uncertainty, the heating has sometimes been done in vacuo,3 the etching gas being admitted when the desired temperature was reached, then pumped out and the specimen cooled in vacuo. The studies of Rosenhain, Humfrey, and other workers 4, 5, 6, 7, 8 dem-

Jan 1, 1922

By Howard Scott, Henry S. Rawdon

The method of demonstrating the structure existing in a metal or alloy at high temperatures, by etching a polished sample after it has been heated to the desired temperature, is quite familiar to metallog-raphists. The usual procedure1 2 is to heat the specimen, previously polished for microscopic examination, to the desired temperature, in a neutral atmosphere (hydrogen or nitrogen), then admit the etching gas (chlorine, hydrochloric acid or similar gas) for a few seconds, and finally, after flushing out the etching gas with the neutral one, cool the specimen in the neutral atmosphere. The pattern produced by etching at a definite temperature is usually taken as a record of the microstructure prevailing at that temperature. It has frequently been pointed out that changes in composition of the surface metal occur during the preliminary heating in the neutral atmosphere, so that the appearance produced by the etching at high temperature may not exactly represent the condition of the interior of the specimen. To overcome this uncertainty, the heating has sometimes been done in vacuo,3 the etching gas being admitted when the desired temperature was reached, then pumped out and the specimen cooled in vacuo. The studies of Rosenhain, Humfrey, and other workers 4, 5, 6, 7, 8 dem-

Jan 1, 1922

By H. S. Rawdon

One of the most vital problems in the manufacture of steel at present is the occurrence of the defects that have been popularly termed "snow flakes," "flakes," or "scabs." Particularly is this the problem of many manufacturers who, during the past 2 yr., have undertaken large-scale production for the first time. A study of the microstructure of such defective material throws considerable light upon the nature of these defects and is essential before measurcs may be taken for the elimination of the defects. Flakes do not appear to be found in the plain carbon steels; they have been found. however, in abundance in some of the simple alloy steels that are being used in such vast quantities; vie., nickel steel of the approximate composition, 0.40 carbon and 3.5 per cent. nickel, and in the chrome-nickel type. The present article summarizes the characteristic features of defective steel of the flaky type as they have been found by laboratory study of numerous specimens, and it aims to show the conditions within the metal that are favorable to the occurrence of this type of defect without entering into the details of mill practice (size of ingot, design of molds, rate of cooling, distribution of cooling stresses, etc.), all of which conditions appear to play a role in the production of these defects. MacrostrUctURe To one familar with flaky steel, the appearance of "snow-flakes" is unmistakable and is not to be confused with other types of defects. Figs. 1 to 6 show the appearance of fractures of steel showing this type of defect; the white silvery area, which always has the appearance of being of a very coarsely crystalline structure, in the specimen stands out in bold contrast to the darker background and readily justifies the use of the term "snow-flakes." Fig. 1 shows the appearance of the faces of the two halves of a nickel-steel forging that has been split to show the interior flakes. Fig. 2 is a nickel-steel bar (carbon 0.40 per cent.,

Jan 1, 1920

By Willard C. Lacy

Rather than attempting to present a summary of the many and highly varied papers that have been presented at this symposium on sampling and grade control, I will attempt to extract the general philosophy of analysis and approach, and attempt to identify the trend of future developments. First, the term "sampling" is used with its broadest connotations. A sample consists of a representative portion of a larger mass, and must represent the mass not only in the grade of contained metals or minerals, but also in all other respects in terms of mineralogy and mineral quality (1, 5), deleterious materials, recoverability of economic components, physical behavior, geophysical response (I), and even archaeological and environmental aspects (7, 11). The sample must be taken from a locality and in such a manner and quantity that it is representative of the larger rock mass. This calls for complete and accurate geological control and an understanding of the nature and distribution of the contained chemical and physical elements and a record of the effectiveness of the different sampling methods. Second, value of a given mass of ore material is based upon its profitability - the difference between recoverable value and costs to achieve recovery, beneficiation and sale. There is a strong movement in mining geology control toward more complete analysis in determining cutoff grades and in grade control, as illustrated by the kriging of metallurgical recovery factors as well as grade at the Mercur Mine (8). To achieve a "profit- ability factor" as a guide for economic mining practice requires further integration of: 1) the value of contained metal or mineral, 2) percentage recovery of values, 3) dilution of ore with waste rock, 4) addition to, or loss of value as a consequence of by-product materials or deleterious components, 5) cost of producing a saleable product plus mini- mum profit to justify the effort (cutoff), and 6) cost of land restoration (7, 11). All these parameters vary with the rock type, rock structure, mineralogy, depth, geometry, mining and metallurgical methods, but they must be sampled and analyzed if sampling and grade control are to reflect profitability. A wide variety of deposits has been presented at this symposium; each deposit with its own problems and special solutions. Deposits containing high unit-value components, e.g. precious metals and diamonds, present special problems in the obtaining of accurate samples and generally require statistical analysis control methods or may disregard or modify occasional high or occasional low values, based upon experience (12 ) Grade control may be accurate for the long term but may vary for the short term. Bulk sampling is always essential. Deposits containing metals or minerals with low unit value are very sensitive to transport costs, and they are often very sensitive to small amounts of deleterious components or differences in physical or chemical behavior. Problems of sampling and grade control change with the genetic type of deposit, with the stage of deposit development and with the size of the information base. Precious metal epithermal deposits (2, 6, 8), because of rapid vertical zonation and erratic lateral distribution of values, have always been difficult to evaluate and maintain grade control and ore reserves. On the other hand, evaluation and grade control are relatively easy in bulk-low- grade deposits (4, 13). However, these deposits generally have a low margin of profit and are sensitive to mining and beneficiaton costs, price fluctuations and political costs. Industrial mineral deposits (5) often must be evaluated on the basis of their behavior, rather than by chemical analysis. Environmental impact generally increases with the scale of the operation, but certain elements or minerals have especially high impact effects (7, 11). In the exploration phase there is no production control of sampling procedures and careful geological observations are particularly essential. The greatest number of problems is related to the oxidized outcrop where the chemical environment of the ore body has changed and the contained values may have been enriched, depleted or values left unchanged (2, 6). Present evidence suggests that gold values may be very mobile under certain conditions (2, 6) and stable under others. Everything must be sampled in detail. Principal values and by-product or deleterious elements may vary dependent upon their position within the soil profile. Such factors as geomorphic position, erosion rate, vegetation, climate, etc., may affect the interpretation (1, 3). During the development phase it is equally easy to overtest, to have "paralysis by analysis," as to undertest (3, 6). Bulk samplng and testing are

Jan 1, 1985

By F. X. Spiegel, D. Bardos, Paul A. Beck

Ti6NileSi7)G is known to be cubic, with 116 atoms in the unit cell. In the present work four new G sili-cides were found with other transition elements and five G germanides. The titanium-group elements are very efficient in forming G phases. The vanadium -group elements are somewhat less efficient, and the chromium-group elements do not form any. Cobalt can replace nickel in most cases, but it is somewhat less efficient. Iron was not found to form any G phases. Germanium is somewhat less efficient than silicon. The (TiNiSi)E phase has been previously identified by Westbrook. However, its crystal structure has not been determined. In the present work the E phase was found to have an orthorhombic unit cell with lattice parameters a. = 7.02, bo = 5.18, co = 11.11A. A large number of other E phases were found at the same stoicheometric ratio in ternary systems of silicon and germanium with transition elements. Lattice parameters similar to those for TiNiSi were measured. The number of atoms per unit cell is estimated at 30 to 36. The vanadium-group elements are somewhat more efficient in forming the E phase than the titanium-group elements. Chromium-group elements were not found to form any E phases. Cobalt is somewhat less efficient than nickel, and iron is less efficient than cobalt. Germanium is not as efficient as silicon. ThE ternary silicide designated as G-phase was first identified by Beattie and versnyder1 and by Beattie and Hagel2 at the approximate composition TiNi2Si. Westbrook et al.' gave the composition as Ti2Ni7Sis. This phase was found to be fcc with a. = 11.201A and 116 atoms per unit cell. Beattie4 and more recently independently Hladishevskii, Kripyakevich, Kuzma, and Teslyuk5 were able to show that this structure is isotypic with MgeSi7CuLe and Th6Mn23. The latter structures had been determined by Florio, Rundle, and snow,' Nagorsen and Witte,7 and Bergman and Waugh.8 According to the crystal structure, Ti8Ni6Si7 may be considered as the ideal composition. The Russian investigators5 identified six additional ternary phases isotypic with Ti6Ni6Si7, in which titanium is replaced by Mn, V, Nb, Ta, Zr, and Hf, and one, namely MneNil6Ge7, in which germanium replaces silicon. They also found that Cr6Ni6Si7, which does not occur as a ternary phase, can be stabilized by replacing 1 at. pct of the Cr by V, Mn, or Ta. Another ternary silicide was found by Westbrook et al.3 at the composition TiNiSi, and it was designated by them as the E phase. The crystal structure of this phase has not been deter-

Jan 1, 1963