Search Documents

By Satish Kate

Indian limestone mines which are highly mechanized in operation and supply limestone to the cement plants have been quite successful in devising ways and means to optimize blasting parameters, so as to have best fragmentation, powder factor, and cost of excavation. In primary blasting mechanized or manually mixed ammonium nitrate Fuel Oil is quite popular in dry holes, and in case of watery holes conventional packaged slurry/emulsions are being used. In order to avail the low density characteristics of the ANFO, some limestone mines have also used Saw Dust and Rice Husk along with ANFO. A number of field trials have been undertaken to explore the suitability of mixing rice-husk and saw dust with ANFO. Presently, about 10% of rice husk/saw dust is being used only to expand the explosive column. The main technical consideration for the use of saw dust/rice husk, has been to reduce the final density and increase the occupancy of explosive in the blast-hole. This not only lowers the detonation pressure in the blast holes, but also reduces cost of explosive without compromising on the fragmentation quality. Besides, with sleeping of the charge there is no substantial fall in the blast quality.

Jan 1, 2006

By C. K. Eilerts

Knowledge of the phase relations of the fluids that exist in the porous spaces of rocks constituting natural petroleum reservoirs and of the behavior of these fluids under various field conditions of operation is essential to the conservation of petroleum and natural gas and to their efficient recovery. The problem of determining whether these fluids are in the liquid or gaseous state and of recognizing the transitions that may take place as the material in the reservoir is subjected to different conditions of pressure and temperature confronts many producers today, especially in certain fields. The subject has grown rapidly in importance since the discovery of and production from deeper reservoirs that have correspondingly higher pressures and temperatures as compared with shallower

Jan 1, 1938

By Hamid Maleki

Prudent design of coal pillars in any mining system requires an estimation of in-situ pillar strength, overburden lateral load transfer capability, and a failure criterion. Pillar strength is typically determined using one of several different empirical pillar strength formulas. For coal reserves in the U.S., a new pillar design method was proposed based on extensive U.S. field measurements in underground mines (7) which accounted for confinement effects. Field measurements in seven U.S. seams indicated highest strength for some Utah mines where the coal seam developed high confining stresses. Lower strength was measured in structurally controlled seams. This method is expanded here including the data from the weaker tertiary coal measure rocks and lower confinement for pillars with low width-to-height ratios. The determination of how much load a pillar is expected to take is partially dependent on the ability of overburden to transfer load laterally; this is useful for selection of panel width and barrier pillars size in select mining applications where long-term stability is required in conservative designs. In caving mining systems, caving of the strata is influenced by geologic, mining and stress conditions and the released energies influences how the pillars react at loads approaching pillar strengths. Overburden deformation and caving mechanisms are analyzed in this paper in multi-panel extractions to enhance the understanding of load transfer, seismicity and coal bump control in deep western U.S. operations.

Jan 1, 2008

By Juel H. Stears

The bureau of Mines analyzed data from 47 coal mine roof-fall resupport accidents that occurred from 1966 through 1974 to identify critical hazards .and problems. These accidents resulted in 62 injuries or fatalities. It was concluded that the majority of the accidents might have been prevented by observance of recommended practices and use of available technology such as setting temporary supports, adequate roof testing, etc. Additional work is needed in the following problem areas where present technology is inadequate: (1) warning of impending roof falls shortly before they occur, (2) better methods of detecting unsafe roof and ribs, (3) providing access to and temporary support of high roofs for testing and bolting, (4) reducing the noise level of stopers, (7) developing temporary roof support; that have greater stability and can be remotely installed, and (6) reducing the number of roof falls through better permanent support.

Jan 1, 1976

By L Schürmann, R Kendall

Social licence to operate is becoming part of a mining company’s DNA in the same way as health and safety. Consequently, mining companies are receiving increasing pressure from their shareholders to ensure that they add enduring value to the local communities in which they operate. Apart from the shareholders, a company has responsibility to suppliers, customers, employees, the government and the community, which means under the social responsibility model they must be accountable to the other stakeholders. External and internal challenges in mining are increasing the difficulty and complexity of mines to operate. The external mining environment has a big impact on mining operations and is driving matters such as the focus on safety, responsible mining and resource management, sustainability issues, profitability and productivity. Considering this, it is expected that the widespread implementation of Environmental, Social and Governance (ESG) related practices across the mining industry in the next ten years will increase, not just for the big players but for juniors as well. Companies, investors, governments and insurers who fail to act on ESG matters are to likely face greater risks. Demonstrating leadership in ESG will ultimately become a differentiating factor and market participants have much to gain from embracing ESG stewardship as part of their competitive advantage. Stock Exchanges have an important role to play in advancing sustainability in the capital markets. It is for this reason that the Sustainable Stock Exchanges (SSE) initiative was founded to serve as a global platform for exploring how exchanges can enhance performance on ESG issues and encourage sustainable investment. The SSE initiative provides an effective platform for dialogue between the United Nations, stock exchanges, investors, companies and regulators in the mining industry. The paper will explain why ESG reporting is crucial for the survival of a mining company and how the lack of transparency could be detrimental to its public image and shareholder relations. The paper will also identify bodies that regulate ESG reporting, as well as the available tools that provide guidelines on reporting ESG matters. Key ESG reporting parameters (at a global scale) will also be highlighted.

Jun 22, 2022

By Pierre Laliberté

Objectifs ?Quantifier les économies d?énergie potentielles liées àl?utilisation de différentes technologies ?Créer un modèle permettant d?évaluer les économies possibles d?énergie en combinant plusieurs technologies ?On ne peut simplement additionner les pourcentages d?économie individuels pour en évaluer le total.

Feb 1, 2008

By Rita D. Sylvester

"THE BUREAU OF MINES was established in the public interest to conduct inquiries and scientific and technologic investigations concerning mining and the preparation, treatment, and utilization of mineral substances; to promote health and safety in the mineral industries; to conserve mineral resources and prevent their waste; to further economic development; to increase efficiency in the mining, metallurgical, quarrying, and other mineral industries; and to inquire into the economic conditions affecting these industries. The organic act of the Bureau, as amended by Congress and approved February 25, 1913, made it the province and duty of the Bureau to ""disseminate information concerning these subjects in such manner as will best carry out the purposes of this Act.""In accordance with that directive, the Bureau reports the findings of its research and investigations in its own series of publications and also in articles that appear in scientific, technical, and trade journals; in proceedings of conventions and seminars; in reference books; and in other non-Bureau sources. The number of these reports, the wide range of subjects they cover, and the variety of mediums in which they appear make the kind of list and index presented III this special publication both necessary and valuable. This issue describes Bureau reports and articles published during the period January 1, 1960 to December 31, 1964. It supplements the 50-year list of Bureau publications issued from July 1, 1910, to January 1, 1960,2 and the 50-year list of articles by Bureau authors published outside the Bureau from July 1, 1910, to January 1, 1960.3 It supersedes the annual lists of Bureau publications and articles from January 1 to December 31, 1960/ from January 1 to December 31, 1961,5 from January 1 to December 31, 1962,6 and from January 1 to December 31, 1963,1 The leading general and technical libraries of the United States maintain files of the Bureau's publications. A list of these libraries appears immediately following this introduction. BUREAU PUBLICATIONSBecause some series of Bureau reports contain both free and sales publications, and because the cost of sales publications varies, prices are indicated in the individual listings of all publications for which charges are made."

Jan 1, 1964

By Guthrie. R. K., H. B. Hill

"INTRODUCTION During the early 1920's world-wide attention was attracted to a group of oil fields (Mexia, Wortham, Currie, Richard, and Powell) later known as Mexia-Powell fault-line fields in Limestone, Freestonne, and Navarro Counties, Tex. Enormous yields of high-gravity oil from the wells in these fields resulted in drilling campaigns that quickly surpassed all previous records for rapid, intensive development of productive areas. The discovery of oil in the Mexia filed in September 1921 was followed quickly by the finding of oil in the Currie field in October. In January 1923 oil was discovered in the Powell field; in February 1924 the Richland field, midway between Currie and Powell fields, was brought in; and in November 1924 oil was discovered in the Wortham field, situated between Mexia and Currie fields. Each of the fileds was developed rapidly: wells were spaced closely and had high initial production; production peaks were reached early in the producing lives of the fields; subsequent decline was rapid, and there was early and rapid encroachment of edge water.In 1927 Bureau of Mines engineers, in their investigations a engineering conditions in oil,completed a preliminary study and published a mimeographed report 4/ on underground conditions in the Wortham field, and in 1928 they reported on production and development problems in the Powell Field. 5/ field."

Aug 1, 1943

By William O. Vanderburg

This paper gives the results of a reconnaissance of the mining districts of Mineral County, Nev., made during the month of June and the first 10 days in October 1936.3/ During the field work virtually all the mining districts in the county were visited and many data were obtained relative to active and inactive properties. The report covers the location of the various mining districts, nature of deposits, ownership, information on past and current activity, data on economic conditions, and general information likely to be useful to operators and investors and others interested in mining. The geology of the deposits is discussed only in a general way. For nearly three-quarters of a century mining tin Mineral County has been the principal if not the only industry of importance. At times it has reached a very low ebb, and at other times it has been attended by the wild excitement that usually accompanies valuable discoveries of precious metals.

Jan 1, 1937

By Staff

The goal of the U.S. Bureau of Mines diesel engine research program is to reduce exhaust emissions from diesel-powered equipment used in underground mines. This research has led to significant advances in aerosol measurement and to the development of more effective emission controls. This Information Circular contains reports of some of the presentations made at the Bureau's Information and Technology Transfer Seminar on Diesels in Underground Mines given in Minneapolis, MN, on September 29-30, 1992. The seminar emphasized the measurement and control of diesel particulate matter emissions. Topics covered include a discussion of the health issues associated with the use of diesel equipment underground, an overview of regulations, measurement techniques for diesel exhaust aerosol, levels of diesel exhaust pollutants found in mines, and modern emission controls. An appendix is included that contains a report describing the capabilities of the Bureau's diesel emissions research laboratory, two papers describing the effects of engine maintenance or: emissions, a paper describing the monitoring of carbon dioxide in mine air as an indicator of air quality, a glossary, and a list of abbreviations and acronyms.

Jan 1, 1992

By Jorgen Elbrond, Noel Billette

"La connaissance du niveau de variation de I' alimentation d' une usine minéralurgique est essentielle pour estimer le taux de récupération dans un concentrateur. De plus, il est important de connaître la période moyen ne de correlation afin d’améliorer la qualité des contrôles et de l' au tornatisation.Le modèle proposé permet de prédire ces paramètres à partir du minerai en place et des activités d'exploitation dans une opération à ciel ouvert. II est basé sur la combinaison des variogrammes directionnels dans diverses zones d'un gisement, ce qui permet de définir la correlation à la sortie de chaquc zone en fonction des decisions opérationnelles, puis sur une loi binômiale modifiée, afin de séparer minerai et stériles dans Ie but de décrire variance et corrélation dans Ie minerai même, Les statistiques classiques sont alors utilisées pour décrire la combinaison de plusieurs zones et obtenir la variance et la correlation au concentrateur.IntroductionUn concentrateur est habituellement rodé de facon à recevoir une alimentation à teneur fixe en métal ; Ie minerai qui s'y presente a, par contre, tendance à osciller auteur de cette valeur cible, tantôt plus riche , tantôt plus pauvre . Ces variations entraînent des pertes de deux types: tout d'abord, la teneur du concentré oscille de facon similaire à celle de l' alimentation , ce qui peut même impliquer des pénalties a I'usine de smeltage lorsqu'elle est trop riche ou trop pauvre; la récupération peut pour sa part être diminuée de plusieurs points par un engorgement du circuit lorsque la teneur est trop forte."

Jan 1, 1984

By M. J. Beus

The Bureau of Mines, under a cooperative agreement with Hecla Mining Co., is conducting a rock mechanics study of the 6,200-ft-deep circu-lar, concrete-lined Silver Shaft in northern Idaho. The objective of the project was to instrument and evaluate lining behavior and rock de-formation when a deep shaft is constructed in a high in situ stress field and anisotropic rock mass. Rock mass displacements were moni-tored with multiple-position borehole extensometers. Liner stress and strain were measured with concrete pressure cells and embedment strain gauges. Field data from the 5,955-ft test level show that rock displacement is controlled by rock mass anisotropy. Liner stress and strain levels reflect the high in situ stress field as well as nearby station and raise construction. Maximum stresses measured in the lining, as a result of shaft excavation, are about one-third of its compressive strength. Subsequent loading pocket excavation resulted in signifi-cantly increased stress and strain levels in the liner. Continued monitoring and preliminary analysis of the data indicate that concrete-lined, circular shafts are stable for the high, unequal horizontal stress fields and rock anisotropy encountered in deep-level mining. Adjacent development work can be expected to significantly alter the initial stress and displacement conditions.

Jan 1, 1984

By W. G. Miller

An overall study was conducted to evaluate the properties and processes influencing the rate and magnitude of consolidation for oil sands fine tailings produced using different extraction processes. As part of this overall study, consolidation tests using slurry consolidometers were carried out for caustic and non-caustic fine tailings. The influence of a change in bitumen extraction process (caustic versus non-caustic) on consolidation properties, namely compressibility and hydraulic conductivity, was determined, as was the effect of adding a coagulant (calcium sulphate [CaSO4]) to caustic fine tailings. For fine tailings originating from two different oil sands ores (Ore A and Ore B), results were presented in terms of variation in average void ratio with time (settlement), void ratio with effective stress (compressibility), hydraulic conductivity with void ratio and coefficient of compressibility and hydraulic conductivity with sodium adsorption ratio. Findings indicated that chemical characteristics of fine tailings (water chemistry, degree of dispersion) do not have a significant impact on their compressibility behaviour and have only a small influence at high void ratio (low effective stress). The biggest advantage of non-caustic fine tailings and treating caustic fine tailings with coagulant is an increased initial settlement rate and slightly increased hydraulic conductivity at higher void ratios. Thereafter, compressibility and hydraulic conductivity is governed by effective stress.

Aug 1, 2010

By W. G. Miller, J. D. Scott, D. C. Sego

An overall study was conducted to evaluate the properties and processes influencing the rate and magnitude of consolidation for oil sands fine tailings produced using different extraction processes. As part of this overall study, consolidation tests using slurry consolidometers were carried out for caustic and non-caustic fine tailings. The influence of a change in bitumen extraction process (caustic versus non-caustic) on consolidation properties, namely compressibility and hydraulic conductivity, was determined, as was the effect of adding a coagulant (calcium sulphate [CaSO4]) to caustic fine tailings. For fine tailings originating from two different oil sands ores (Ore A and Ore B), results were presented in terms of variation in average void ratio with time (settlement), void ratio with effective stress (compressibility), hydraulic conductivity with void ratio and coefficient of compressibility and hydraulic conductivity with sodium adsorption ratio. Findings indicated that chemical characteristics of fine tailings (water chemistry, degree of dispersion) do not have a significant impact on their compressibility behaviour and have only a small influence at high void ratio (low effective stress). The biggest advantage of non-caustic fine tailings and treating caustic fine tailings with coagulant is an increased initial settlement rate and slightly increased hydraulic conductivity at higher void ratios. Thereafter, compressibility and hydraulic conductivity is governed by effective stress.

Jan 1, 2010

By H. B. Hill

Virtually from the date of its discovery in December 1928 the Oklahoma City oil and gas field, Oklahoma County, Okla., has attracted national and international attention. The history of the field has been associated closely with rules and regulations pertaining to production control and proration practices. Early development was rapid, and Oklahoma City soon attained the distinction of being the first major field in which the producing wells were over a mile in depth. Before the structural features of the reservoir had been disclosed every outpost well was considered a "wildcat", so complex appeared the underground geology, The wells not only were deep and the reservoir pressures high, but the production from the early wells was a high A.P.I. gravity oil, accompanied by large volumes of gas. Several "blow-outs" and fired occurred during the early development, and the close proximity of these now unusual events to a large city gave the field much publicity, both local and national. Later, when its production threatened to demoralize the market for oil and its products, the Oklahoma City field again attracted wide publicity. The then little understood geology of the underground reservoir and the diversity of ownership of the land overlying the producing structure made orderly development and production difficult to enforce. Proration was enforced with difficulty., and the, rate of production from the field continued to increase until, on August 4, 1931, martial law was declared in all prorated fields of the State, and most of the wells in the Oklahoma City field wore shut n. On October 9, 1931, permission was granted t o reopen and prod e the wells in the Oklahoma City field. The order permitting production of the wells provided that during the period beginning October 10 and extending to October 20, 1931, all wells in the field that hid not produced more oil than specified under the earlier proration orders and that had been shut in for the required 55-day period were permitted to produce 5 percent of their last potential during that 10-day period. On November 7, 1931, the Corporation Commission of Oklahoma issued an order which divided the Oklahoma City field into the Wilcox, Arbuckle, and Lower Simpson zones for proration purposes. Wells producing from the Wilcox zone were allowed to produce 4 1/2 percent of their potential5/ from November 1, 1931, to January 1, 1932; Arbuckle limestone wells were allowed to produce 250 barrels of oil daily; and Simpson sandstone wells which had a potential of over 2,000 barrels per day or which made 3 percent or more water were allowed to produce 200 barrels of oil per day.

Jan 1, 1937

By Alain Dorval

"''Purification of marine sands from Les Iles-de-la-Madeleine''This paper presents the results of the work that has been done at CRM pilot plant for «Les Silices du Golfe Inc.». Essentially the purpose of this piloting was to demonstrate, on a semi-industrial scale, the process of purification of marine sands from Les Iles-de-la-Madeleine; that had been developed by CRM Process Development Service. This purification is necessary to produce silica suitable for the glass sand and the foundry sand markets.Introduction«Les Silices du Golfe Inc.» is a company who intends to dredge marine sands around the «Les Iles-de-la-Madeleine» coasts. The material will be transported to Gaspesia where electricity, water supply, and a convenient site is available to treat it. A high purity silica intended for glass sand and foundry sand markets will be produced. The objectives of this purification process are to remove organics, calcium, feldspars and iron.Material ReceivedCRM received 50 tons of sand with Si02 varying between 80,6 and 99,3 % (see Figure.1). The highest variations in impurities were the calcium and lost on ignition. We notice direct relation between% SiO2, % CaO and % L.O.I. as you can see on the following Figures 2, 3 and 4."

Jan 1, 1994

By AIME AIME

COMMITTEES. CANAL ZONE.-Col. George W. Goethals, U. S. A., Chairman; Lt.-Col. H. F. Hodges, U. S. A. ; Lt.: Col. D. D. Gaillard, U. S. A. ; Lt.-Col. William L. Sibert, IT. S. A. ; H. H. Rousseau, U. S. N.; Col. W. C. Gorgas, U. S. A.; Maurice H. Thatcher ; Joseph Bucklin Bishop ; Lt.-Col. Charles F. Mason, U. S. A.; S. B. Williamson ; Major Eugene T. Wilson, U. S. A. ; Edward Schildhauer ; Henry Goldmark ; Edward C. Sherman ; W. G. Comber ; W. B. Corse ; J. A. Walker; Joseph A. Le Prince; J. A. Smith ; Lt. Frederick Mears, U. S. A. HAVANA.-V. T. Polledo, Chairman; Diego Lombillo Clark, Jose Primelles, J. R. Villalon, Jose Artola, J. Ducassi, Luis Morales, Enrique Montonlieu. ENTERTAINMENT ON SHIPBOARD.-William L. Saunders, Chairman; Mr. and Mrs. S. D. Warriner, Mr. and Mrs. Thomas Robins, Mr. and Mrs. George.D. Barron, Mr. and Mrs. R. B. Watson, W. E. Greene. GENERAL MANAGEMENT. .Joseph Struthers, Chairman; Albert E. Vaughan. There were ten sessions of the Institute held for the presentation and discussion of, technical or professional papers. Eight of these sessions were held on the steamer while en route, and two in the ball-room of the Hotel Tivoli, at Ancon, C. Z. Mr. David W- Brunton, President of the Council, presided at all the sessions, except the sixth, at which Mr. Charles Kirchhoff, past President, occupied the chair. The following list includes the papers presented in oral abstract by the authors: First Session., October 24. The Summit Hill Mine-Fire, by W. A. Lathrop, Philadelphia, Pa. Mine-Fire at the Calumet and Hecla Mine, No. 8 Shaft., by S. D. Warriner, Wilkes-Barre, Pa. Fire in the Big Lick Stope, Lykens Valley and Williamstown Colliery, by R. V. Norris, Wilkes-Barre, Pa. Mine-Fire in the Hecksherville Valley, Schuylkill Field, Pa., by W. J. Richards, Pottsville, Pa.. Fire in the Monarch Mine, near Rock Springs, Wyo., by S. A. Taylor, Pittsburg, Pa.

Dec 1, 1910

By Philippe Angers

This article analyzes the social acceptability process of a mining project located in an existing city. It will explore how the principles of sustainable development have been integrated in the project of the Canadian Malartic open pit mine held by the Osisko Mining Corporation, and the corporate social responsibility (CSR) initiatives proposed to strengthen the social acceptability of the project. This mine is located on the ancient south quarter of Malartic and has required the displacement of hundred of houses and five institutions. The location and the inherent social impacts generated by the relocation of the citizens of the south quarter makes this case particularly interesting to understand social dynamics in an era of environmental consciousness. These major constraints of the mine generate high expectations within the urban population with regard to the social and economic benefits it will receive from the project. In a context where society demands higher CSR from the corporation, Osisko is closely followed regarding their actions toward the sustainable development principles to see if they respect the environment and the desires of the community. From the beginning, the company had to be a model of sustainable development in various aspects reflected by the manifold interest of the population. To understand the endeavor made by the company to fulfill the demand of CSR, we will analyze how the company understood sustainable development principles and what CSR initiatives Osisko company put forward. We will explore the involvement of the company in various social aspects like employment, employee satisfaction, and the level of commitment to non-discrimination policy in employment, notably with the native populations. We will also take a closer look at the relationship built by the company with the community and the level of commitment with the various stakeholders of the community. In this way, we will be able to seize the level of involvement of the company in the fulfillment of the principles of sustainable development toward a higher CSR, and to specify the trajectory adopted to build social acceptance.

Aug 1, 2013

"Block caving is the preferred underground mining method to profitably extract massive, low-grade orebodies; however, lack of cave access inhibits understanding the rockmass response to mining, which is needed for safer, more productive operations. Combining large datasets from multiple sources with virtual reality scientific visualization (VRSV) is an alternative method for understanding complex cave behaviour, by providing virtual access to the cave. A customized VRSV module was developed at UNSW Australia to investigate rockmass response to undercut developments at a case-study block caving operation. Time/sequence effects are investigated in rockmass response to blasting, which is an important factor in hard-rock mines.RÉSUMÉ La méthode d’extraction souterraine par blocs foudroyés est la méthode préférentielle pour extraire rentablement des gisements massifs à faible teneur. Toutefois, le manque d’accès à la chambre restreint la compréhension de la réponse de la masse rocheuse à l’exploitation, ce qui est nécessaire pour obtenir des opérations plus sécuritaires et plus productives. La combinaison de grands ensembles de données de multiples sources avec la visualisation scientifique par réalité virtuelle (VRSV) constitue un autre moyen de comprendre le comportement complexe de la chambre en fournissant un accès virtuel à la chambre. Un module de VRSV sur mesure a été développé à l’Université de Nouvelles-Galles du Sud (UNSW) en Australie afin d’étudier, dans une étude de cas d’une exploitation par blocs foudroyés, la réponse de la masse rocheuse aux développements de galeries de sous-cavage. Les effets de temps/séquence sont étudiés dans la réponse de la masse rocheuse au sautage, ce qui est un facteur important dans les mines de roches dures."

Jan 1, 2016

By Daniel Brutto

"Environmental considerations are a key driver within marine mining consenting processes across different national and international legislative regimes and are critical in shaping the global public perception of the industry. As a result, it is vital that mining companies seeking to operate within marine environments establish a robust understanding of the sensitivities of the seabed environments in which they are active, the impacts of their activities and the ability of the environment to recover from these impacts. The significant risks of failing to do so include an inability to either obtain or maintain operating permits. At the individual project level, the environmental effects of any given development project are typically defined within the scope of an Environmental Impact Assessment (EIA). For well-established industries operating in well-studied environments this approach typically works well. However, where emerging industries or existing industries that are operating within new environments are concerned, there may be significant knowledge gaps pertaining to our understanding of how specific anthropogenic practices or activities interact with the marine environment. These knowledge gaps can cause significant uncertainties pertaining to the likely significant effects of a project. Such uncertainties may result in barriers to industry and economic progress, increased consenting risks, increased project costs to be borne by individual project developers through the acquisition of additional environmental data during the pre-consent or post-consent project phases, project delays and/or significant increases in environmental monitoring burdens with corresponding increases in project costs."

Sep 1, 2014