Search Documents

By Adam Shang Robert Fu

The Yung-Chung-Tunnel in Taiwan, constructed for the Taiwan-East Railway Bureau, collapsed during construction when a water bearing, fractured marble zone was intersected. The inflow was approximately 4,000 liters/second. In spite of 30 relief holes the total inflow into the tunnel remained constant. The pre-excavation grouting through the re-aligned tunnel had to be conducted under extreme flow-conditions. A hot bitumen grouting program was selected for technical and economical reasons out of 13 international proposals. The technical challenges were: grouting under severe flow conditions high formation water pressures to be injected with hot bitumen at high temperatures and pressures The hot bitumen grouting program resulted in a dramatic reduction in the hydraulic conductivity and stabilization of the formation and facilitated a problem-free excavation.

Jan 1, 2007

By J Guo, K Williams, J Y. Guo, A W. Roberts, M Jones, B Chen

Numerical simulations using the discrete element method (DEM) were carried out to investigate the flow patterns and stress field redistribution at the hopper and feeder interface. The influences of different filling heights, belt speeds and clearances between the hopper bottom and feeder surface on feeder loads were studied. Meanwhile, experiments were conducted by utilising wedged plane-flow hoppers with different configurations and horizontal feeders with various clearances. The simulation results were compared with theoretical values and experimental measurements. In terms of the cases presented in this study, simulation results reveal good agreements with experimental observations regarding the flow pattern. Being similar to the theoretical values, the simulations provide close predictions on vertical feeder loads for steady flow states, but they may show significant overestimations for initial states. Additionally, suggestions are given for relevant simulation parameters based on the comparisons shown in this investigation.CITATION:Guo, J, Roberts, A W, Williams, K, Jones, M, Chen, B and Guo, Y J, 2017. Simulation investigation of flow patterns and feeder loads at hopper/feeder interface, in Proceedings Iron Ore 2017, pp 173–182 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By G. H. Damon

Since 1963, Bureau of Mines Information Circular 8179 has served the mining industry as a fundamental safety guide in the field of blasting agents. In the intervening 14 years, many changes have occurred, and this report presents revised and new recommendations which recognize these changes. For example, AN-FO is now supplied mostly premixed, whereas in 1963 much of it was mixed by the blaster; aluminum metal (A1) and other fuels are now often added to AN-FO to increase strength, and flake aluminum powder is used as a sensitizer in water gels; and water gels or slurries that are now extensively used were just coming into practical use in 1963. To provide the widest possible margin of safety, some of the Bureau's recommendations are more stringent than existing regulations,

Jan 1, 1977

By Steve Kral

In the United States, the U.S. Environmental Protection Agency (EPA) is set to implement its Tier 2 air quality standards governing high-horsepower, off-road diesel engines. The regulations take effect in January2006. In Europe, similar standards, called Stages, are due to take effect about the same time. And other markets, such as Japan and Australia, have their own standards on tap. Tier 2 standards will further reduce the amount of nitrogen oxide (NOX), sulfur dioxide (SO2), diesel particulate matter (DPM), carbon monoxide (CO) and hydrocarbons off-highway diesel engines are allowed to emit. And even more restrictive Tier 4 standards are due in 2011. The upshot is that operators of high-horsepower engines, particularly in mining, will begin using in their new off-road haul trucks, excavators, shovels and other mining machines diesel engines that are designed to meet these more stringent standards.

Jan 1, 2004

By Lee Sieng Kai

This paper presents the result of the analysis of strain-dependent concrete modulus from full-scale static axial compression load tests conducted on more than 200 instrumented cast-in-place barrettes and bored piles over the past 12 years, covering commonly adopted grades of concrete for heavy foundation construction in Malaysia and Singapore. The concrete modulus values, Ec, analysed were directly back-calculated from the material of the instrumented test piles by means of placing a layer of vibrating wire strain gauges near the pile head region. The best fit curve for back-calculated concrete secant modulus versus measured axial strain follows non-linear behaviour for both categories of test pile samples analysed. The result of the analysis seems to suggest that using average constant modulus value would generally lead to a significant error in load distribution computation, particularly at high stresses region.

Jan 1, 2006

By Richard A. Grieve

A 63.5 metric tons per hour (70 TPH) demonstration coal preparation plant was constructed on the Iowa State University campus, Ames, Iowa, as a part of the Iowa Coal Project funded by the state of Iowa and administered through the Energy and Minerals Resources Re-search Institute. Processing equipment in the plant circuit includes a heavy media separator, concentration tables, separating and dewatering screens, and conveying equipment. Coal samples of size 907 metric tons (1000 tons) with sulfur contents ranging from 2.5 to 8.75% sulfur from seven mines in the state of Iowa have been pro-cessed in the plant. Sulfur reductions have averaged 35%. With ash reduction averaging 45%. Equipment for advanced fine coal beneficiation research is currently being installed in the plant to include a slurry pretreatment circuit, froth flotation, oil agglomeration, pelletization, hydrocyclones, advanced design thickener and disc filtration.

Jan 1, 1978

By A. Baldwin

Reports technical progress in designing four machines to be used in mining coal underground, applying innovative concepts at the design stage (instead of add-ons). A study phase was followed by design activity, including calculations supporting the designs. Scale models of three machines were built, and a full-scale mock-up of the conventional loader was used to measure human factors parameters.

Jan 1, 1976

By Jon K. Ahlness

The Bureau of Mines investigated technologies for testing the integrity of in situ leach mining wells, as required by environmental regulations. To test for leaks, inflatable packers were used to seal the well casing. Laboratory testing determined that the packers could contain a casing pressure up to 50 to 60 psi (345 to 414 kPa) less than the packer inflation pressure. Single-and double-packer configurations were successfully field-tested in 32 wells ranging from 500 to 530 ft (153 to 162 m) in depth. A rigid pipeline and a hoist truck were used to run the packers in and out of the wells for the double-packer tests, which averaged 2-1/4 h each. In an effort to decrease the time of the rigid-pipe double-packer test. a self-contained trailer-mounted test system was designed and built. It utilizes a winch and steel cable to run the packers in and out of the well and high-pressure nylon tubing for packer inflation. This system was successfully field-tested in eight wells averaging 650 ft (198 m) in depth and resulted in a time savings of 13 pct and an operator-hour reduction of 42 pct.

Jan 1, 1985

By R. Frim, S. D. Ukeles

The present U.S. production of bromine is from inland brines located in Arkansas and Michigan. The most concentrated domestic brines (up to 5,000 ppm bromide)are situated in Arkansas. Less concentrated brines(about 2,500 ppm bromide) are located in Michigan. The amount of bromine sold or used in the United States came from three companies operating in those two states. Its value was $191 million. In 2004, the estimated U.S. bromine production was 222 kt (244,000 st). That compared with 216 kt (238,000st) produced in 2003.

Jan 1, 2005

By A. Yaghini, Y. Pourrahimian

"Human factors (HFs) play an important role in the mining and mineral industry, affecting operational and maintenance efficiency and safety. Despite the introduction of new technologies and automation in this sector, it is well known that a significantly large proportion of total human errors occur during the operation and maintenance phase. A comprehensive literature review of HFs across several industries is provided. From this review, the impact of HFs on operation and maintenance is summarized, with a focus on what the mining industry is currently doing and what opportunities exist for additional improvements. Future research directions and themes are also identified.RÉSUMÉ Les facteurs humains (FH) jouent un rôle important dans l’industrie des mines et des minéraux, en ce qu’ils affectent l’efficacité et la sécurité de l’exploitation et de l’entretien. Malgré l’apparition de nouvelles technologies et de l’automatisation dans ce secteur, il est bien connu qu’une grande partie des erreurs humaines (EH) se produisent durant une phase d’exploitation et d’entretien. Cet article propose une analyse documentaire approfondie des FH dans plusieurs secteurs. L’impact des FH sur l’exploitation et l’entretien est résumé à partir de cette analyse, une attention particulière étant accordée à l’évolution de l’industrie minière et aux possibilités d’améliorer davantage ses activités. Sont également identifiés les futurs thèmes et voies de recherche.INTRODUCTIONDuring the past several decades, the mining industry has focused on improving equipment, machinery, and methods that have led to more advanced hardware and software, equipment with higher reliability and productivity, and other technological advancements. These actions have improved safety and productivity and have reduced casualties and maintenance workload. Although today’s mining equipment and machinery are technologically advanced and highly reliable, the risk of accidents is still relatively high and key performance indicators have not improved significantly compared to other industries (Sorensen, 2012). A prominent reason could be due to insignificant integration of human factors (HFs) as part of planning, operation, and maintenance activities. The current mining system is a people system, and inevitably HFs and human error (HE) figure prominently in all aspects of this industry. Even the most advanced technologies and innovations require operators and maintainers with significant knowledge and skill, which could increase the potential for HE."

Jan 1, 2018

By Neo Molelekeng, Jocelyn Bouchard, Rebecca Monnapula, Martin Émond

"Xstrata Alloys – Eland Platinum concentrator (South Africa) has recently been commissioned and is now initiating a challenging optimisation program encompassing the entire operation. Process control improvements are key elements of the program and initial results have demonstrated how leveraging from current assets can bring significant improvements through overall reduction of variability. This paper gives a brief overview of the operations and details how Eland is striving to become a top tier leader with advanced regulatory control strategies recently implemented. Results reveal that what can be achieved in a standard control system (PLC or DCS) should not be underestimated as the first interventions led to a steadier operation of the primary ball mill circuit. Following the improvements, significant and sustained reductions of standard variation were observed for key process variables around their set-point: primary ball mill feed rate (72 %), rougher feed density (58 %), and rougher feed flow rate (47 %). A path forward has been identified to tackle further opportunities around the primary grinding circuit: water balance management, throughput optimisation as well as charge and power draw control.INTRODUCTIONThere are numerous approaches to mineral processing plant optimisation. As the benefits of determining the right reagent types, mix, dosage and addition points, or the proper charge of grinding media in a mill are fully appreciated, there is still nowadays some misunderstanding and misconceptions about process control in general and how it can contribute to the whole optimisation process. The confusion between the various disciplines involved, i.e. instrumentation, control system programming, automation and process control, certainly does not serve the best interest of the industry with this regard."

Jan 1, 2010

By Kumar A, Mishra N. C

For each tonne of chromite ore mined in Sukinda, approximately ten tonnes of fine overburden material is generated. The overburden typically contains about 30 - 60 per cent Fe2O3, 0.3 - 1.1 per cent Ni, four to nine per cent Cr2O3 and 0.04 - 0.2 per cent cobalt and is being discarded leading to loss of valuable metals and creating environmental pollution. In order to take the advantage of presence of iron, nickel and chromium, the present studies advocate the utilisation of nickel lateritic chromite overburden for production of Ni bearing pig iron through blast furnace extracting maximum iron and nickel from the chromite overburden. The present paper deals mainly with the beneficiation of chromite overburden, sintering characteristics and thermodynamic studies. The beneficiation study shows that a beneficiated concentrate having Fe - 50 per cent and Ni -- 1.1 per cent can be achieved from chromite overburden having Fe - 30 per cent and Ni -- 0.7 per cent. Sintering studies have been carried out with bed height of 300 and 450 mm at a suction of 600 and 900 WG respectively. The results reveal that good quality sinter can be produced from chromite overburden concentrate with a basicity of about 1.0 and coke breeze consumption rate about 16 per cent. In all the experiments, Tumbler Index, Abrasion Index and Shatter Index was found to be in the range of 65 - 70, 4.5 - 5.5 and 85 - 90 respectively. The other parameters namely softening temperature, melt down temperature, reduction degradation test and relative reducibility have also been determined. A thermodynamic analysis has also been carried out to make a technological assessment of the process for the production of alloyed pig iron from chromite overburden in blast furnace which shows that it is possible to produce nickel bearing pig iron in blast furnace using the sinter up to 80 per cent. Techno-economic analysis reveals that this route will yield a substantial profit even after accounting for cost of beneficiation, extra coke, raw materials and extra slag produced.

Jan 1, 1999

By Bhaskar B. Thapa, Michael T. McRae, Johannes V. Greunen

This paper describes the preliminary design of the fourth bore of the Caldecott Tunnels along State Route 24 in Oakland, California. The paper focus is on two major aspects of the project: initial support system design and seismic design. The initial support system was designed based on the New Austrian Tunneling Method (NATM).NATM provides the required flexibility to accommodate the variable ground conditions in the weak, folded, and faulted rock along the alignment. The seismic design provides a final lining system that meets serviceability requirements for a 1,500 year seismic event with an estimated peak ground acceleration of 1.2g.

Jan 1, 2007

By Ron Frye, Carl Liibbe, Wayne Curtis, Julie Pecori, Dan Leach

Test work comparing the performance of a Low Density Porous Ammonium Nitrate Prill to regular Porous Ammonium Nitrate conducted in Pennsylvania and New York showed that less ammonium nitrate was required to perform the same work and that improved sensitization of an emulsion/ammonium nitrate blend reduced “orange fumes”. Fragmentation was similar in all tests with improved heave and throw experienced.

Jan 1, 1997

By Beevers J

The Ok Tedi Project is now a high production open-pit porphyry copper mine located in the Star Mountains of Papua New Guinea (PNG). At present, total daily production is 190 000t of ore and waste. Large scale drilling and blasting has only been in operation since 1988, prior to which all material was removed by ripping and dozing. This paper reviews the steps taken over the last 12 months in establishing a more efficient drilling and blasting operation and highlights the significant reduction in powder factor. These improvements have been achieved largely through the introduction of air-bags, controlled pattern expansion and an overall focusing on the operation by involving consultants, ICI's technical service and internal departments.

Jan 1, 1991

By Richard Manrique

"La implementación del proyecto de modernización de la fundición de cobre de Southern Peru Copper Corporation requiere cambiar la metodología de funcionamiento de los sopladores para la etapa de conversión. En este sentido, el presente texto señala los aspectos del Sistema de control maestro de reparto de carga implementado en la Fundición de Ilo con excelentes resultados, logrando mejorar el rendimiento de los equipos con una antigüedad de mas de 30 años e invirtiendo tan solo en nuevos controladores en una etapa ligada directamente a la línea de producción. Mantener la variable primaria presión en la red de sopladores, compartiendoóptimamente la carga entre los sopladores en la red, mientras que, se minimiza el riesgo de surge, consumo de energía y los disturbios en el arranque y el paro de sopladores individuales, el sistema deberá ser lo suficientemente flexible que no deberá de perturbarse ante la salida frecuente de los convertidores, es decir deberá de mantener las presiones y flujos a la descarga del manifold ante las variaciones en el consumo de aire todo esto con un mínimo de venteos al ambiente."

Sep 19, 2006

By Douglas Beahm

Energy Metals Corp. (EMC) holds numerous mineral properties in the northern portion of the Great Divide Basin. The JAB property is one of several potential properties being planned for development as a satellite facility to the greater Antelope uranium project. A National Instrument 43-101 Technical Report was completed for the JAB property. This report estimated total measured and indicated mineral resources on the property totaling 1.6 kt (3,555,022 lbs) U3O8 contained in 2.2 Mt (2.4 million st) at an average grade of 0.073 percent U3O8 at a 0.25 grade times thickness (GT) cutoff in accordance with CIM Standards on Mineral Resources and Reserves. The JAB property is located in Sections 13, 14, 15, 16, 21, 22 and 23, Township 26 North, Range 94 West, approximately Latitude 42° 14’ North and Longitude 108° 00’ West (Fig. 1). This property consists of unpatented mining lode claims and Wyoming state mineral leases com-prising approximately 850 hm2 (2,100 acres).

Jan 1, 2007

By Patrick Pelletier, Pierre-Alexandre Bossé, Julie Fournier, Gianni Bartolacci, Jayson Tessier, Ahmed Bouajila, Carl Duchesne

"This paper summarizes research into the study of the control of flotation processes based on froth images. The use of numerical image analysis techniques for the extraction of significant patterns (froth structure and colour) from industrial flotation froths is discussed.First, the froth was analysed by the use of the Multivariate Image Analysis (MIA) method to extract the spectral variation contained in a RBG image. The Partial Least Squares (PLS) was applied to develop the empirical model for the prediction of froth grade. The results of this application are illustrated using one industrial case study.Second, the froth was also analysed by Gray Level Co-occurrence Matrix (GLCM) and Wavelet Transform Analysis (WTA) to extract features related more to morphological aspects. Since there is useful information hidden in froth texture, these methods are used as texture descriptor to classify different types of froths.Third, a control strategy based on a froth structure indicator was developed and implemented on an industrial zinc flotation circuit. The feedback controller uses a reagent flow-rate in order to maintain the froth structure at its set point. Process improvements obtained with the implemented control strategy are highlighted.Finally, the feasibility to implement a hybrid control strategy consisting in a froth structure supervision controller based on the froth concentrate grade estimated by MIA and recovery inferred by image analysis is discussed.INTRODUCTIONThe development of control strategies to achieve satisfactory control performance has always been a great challenge for engineers and the need for improved process diagnosis, control and optimization has become more and more evident for the mineral processing industry in the last decades. That is why new process variables need to be measured particularly in highly multivariable processes such as flotation. This industrial process is subject to a wide variety of disturbances mainly generated by frequent and sometimes abrupt changes in physical and/or chemical ore characteristics and also, due to some irregularities in manual process operating procedures. A flotation circuit scheme is always a complex network of more than two dozens slurry streams. Information about those streams (% solid, metal content analysis and flow rates) is important for process diagnosis performance evaluation and control. Also, because of the grade decrease and increasing complexity of the new processed ores, more instrumentation outputs and more powerful and significant pr"

Jan 1, 2005

Preparation of MgO Nano-Particles with Magnesite

Sep 13, 2010

By M. Ganster, H. Krenn

The mission of the project is the fast and cost-effective rehabilitation of decommissioned lignite mining and coal upgrading facilities. This is necessary to ensure the successful future utilization of these sites. On the one hand, for founding new industrial and commercial facilities and on the other hand for touristic activities.

Jan 1, 2013