Search Documents

By Michael Rieber

A new mode of coal transportation based on the principles of pneumatic conveying has been recently, proposed by Soo, et al. [5]. Pneumatic transport is not a novel concept and commercial experience with pneumatic pipelines for short haul distances is plentiful. The list of applications is long and includes transporting ores, chemicals and pharmaceutical products, agricultural products, and domestic and industrial wastes. The study by Soo, et al. [5] updated an earlier one [l0] and presented the most recent economic evaluation of pneumatic transportation of coal. Their preliminary study concluded that there are immediate advantages for short-distance transport (less than 100 miles) and that it is both technologically and economically feasible. That study also concludes that pneumatic transport has a higher potential and more promising profitability in long-distance applications than rail if new track and roadbed must be built. Some of the advantages of long and short distance pneumatic pipeline transport of coal compared to rail and slurry transport are: 1) Replacement of diesel fuel consumed by unit trains, as the pipeline can be powered by coal-generated electricity; 2) Reduction of the skilled-labor costs required for upgrading and maintaining railroads; 3) Elimination of signaling, rerouting and overpass costs due to increased rail traffic on' mainline trackage;

Jan 1, 1977

By I. Gil, J. -C. Roegiers

Abstract Hydraulic fracturing is a technology that has been utilized for more than 50 years in the oil industry. It was originally used for stimulating hard, brittle formations which typically exhibit low permeabilities and roughly linear elastic behavior. Nonetheless, an increasingly important segment of the industry is currently stimulating very soft and poorly consolidated formations; where the assumptions of ideal elasticity and relatively small fluid leakoff fail to hold (e.g. Gulf of Mexico, West Africa, Alaska, East China). In these rocks, hydraulic fracturing stimulation has been used for several years to control and solve critical production problems such as sanding and formation damage (caused during completion and drilling operations). Although successful1, the application of this method has not been accompanied by robust fracturing modeling techniques. In addition, long term production increases were often not materialized. In other words, engineers have been able, via trial-and-error, to avoid major ‘operational’ problems but with no optimization of such treatments. Thus, most hydraulic fracturing projects carried out in poorly consolidated rocks render unexpected results. A recent worldwide survey on net pressures by the Delft Fracturing Consortium (Papanastasiou, 1997) indicated that net pressures encountered in the field are 50% to 100% higher than the net pressures predicted by conventional fracturing simulators. The difference is yet higher for the case of poorly consolidated formations (Pak, 1997). The theory for the construction of a fully coupled elastoplastic three-dimensional hydrofrac simulator, specifically conceived for unconsolidated rocks, is presented in this paper. This novel model calculates the dimensions and changes in shape of the fracture(s) being created during hydraulic fracturing operations. No assumptions are made regarding either shape or geometry of the crack(s). Three main failure criteria are used simultaneously in this model: tensile and shear stresses, and volumetric strain. Incremental forms of the governing equations of equilibrium and fluid flow are presented. The scheme chosen for solving this problem is the finite elements method, which allows both equations to be solved simultaneously at any instant in time. Résumé La fracturation hydraulique est une technologie qu’a été utilisé pour plus que 50 ans dans l'industrie pétrolière. Elle a été utilisée au début pour stimuler les formations dure et fragile que typiquement ont des perméabilités basses et un comportement élastique à peu près linéaire. Néanmoins, un segment plus important de l'industrie stimule actuellement des formations mal consolidées; où les suppositions d'élasticité idéale et de relativement petite fuite de fluide ne se tiennent pas raison (par exemple le Golfe de Mexique, l'Afrique d'ouest, Alaska, la Chine de l'est). Dans ces roches, la stimulation avec fracturation hydraulique a été utilisée pour plusieurs années pour contrôler et résoudre les problèmes critiques de production comme les dommages de formation et d’ensablement (causé pendant les opérations de l'accomplissement et forage). Bien que prospère, l'application de cette méthode n'a pas été accompagnée de techniques robustes pour le modelage de fractures. En outre, les augmentations à long terme de production n'ont pas été souvent concrétisées. En d'autre termes, les ingénieurs ont pu, via le procès et l’erreur, éviter les majeur problèmes ‘opérationnel’ mais avec aucune optimisation de tels traitements. Ainsi, la plupart des projets de fracturation hydraulique ont été exécuté dans des roches mal consolidées et ont rendu résultat totalement inattendu. Une récente étude mondiale sur les pressions nettes par le Consortium Delft pour Fracturer (Papanastasiou, 1997) a indiqué que les pressions nettes qu’ont été rencontré dans le champ sont environ 50% à 100% plus hautes que les pressions nettes prédites par les simulateurs fracturant conventionnels. La différence est pourtant plus importante pour le cas de formations mal consolidées (Pak, 1997). La théorie de construction d'un simulateur elastoplastic d’hydrofrac à trois dimensions entièrement couplé, en particulier conçu pour les roches non consolidés, est présentée dans ce papier. Ce nouveau modèle calcule les dimensions et les changements dans la forme de(s) fracture(s) étant créé pendant les opérations de fracturation hydraulique. Aucune supposition n’a été faites en ce que concernant la forme ou la géométrie

Jan 1, 2003

The Particulate Mineralogy Unit has been established at the College Park, Maryland, Metallurgy Research Center. The Particulate Mineralogy Unit will have the responsibility within the Bureau of Mines for the characterization of particulate minerals which have potential for adverse environmental effects. The Unit will provide a focal point for identifying particulates in connection with environmental problems related to the activities of agencies such as OSHA, HEW, EPA, and MESA. The Particulate Mineralogy Unit is seeking to clarify the ambiguities surrounding the mineralogy of and terminology used for asbestiform minerals and other mineral particles. The Unit?s investigations of the morphology, composition, and structure of asbestiform minerals and their nonasbestos analogs have made its members recognized experts in this field. The information which it develops on the characterization of asbestos and other particulate mineral forms such as silica should provide a technically rational basis for decisions by regulatory agencies. Those desiring further information, contact Dr. W. J. Campbell, Program Coordinator, College Park Metallurgy Research Center, College Park, MD 20740, telephone: 301-344-4014. ALUMINUM: For over a month, domestic producers have priced 99.5 percent grade primary aluminum ingot at 48¢ per pound. In the same period, merchants raised ingot quotes by 1.5¢-2.5¢ to a range approaching 44¢-47¢ per pound.

Jan 1, 1976

By Thomas T. Read

I. INTRODUCTION. WHEN so much has been written upon a subject on which so little definite information is available as upon this, some reason must needs be assigned for adding to the volume of literature. A sufficient reason is found in the probable great future importance of China as a producer of mineral wealth. The present undeveloped state of mining in the Empire is due to many causes, among which the most important are the relatively simple needs of the population, the lack of transportation-facilities, the inelastic regulations governing the industry, and the superstitious reluctance of the people to make excavations which might disturb the spirits of the earth and air, or of ancestors. Iron is the metal most in demand, yet the needs of the population, until recently, only made necessary a production of approximately 0.5 lb. of iron per capita per year. The present annual production of iron for domestic consumption, in the United States, is nearly 600 lb. per capita. The curious state of development of transportation in this interesting country has been a greater handicap upon the mining industry than upon any other. The point upon which it hinges is the absence of a road-system. Except for a few military roads, now almost impassable, there are no roads in China; that is to say, there is no land which is set aside as a right of way, belonging to the commonwealth. Throughout the agricultural districts, generally speaking, the entire area is in private ownership, and the lines of travel are between fields. There is a constant struggle for existence between the owners of the land and the traveling public, with the natural result that the so-called roads usually

Mar 1, 1912

By J. Bélanger, B. Semlali, M. Grenon

RÉSUMÉ La conception des fosses ainsi que l'évaluation des ressources géologiques et des réserves minières sont désormais réalisées entièrement à l'aide d'outils informatiques spécialisés. Cependant, plusieurs analyses, pourtant essentielles à l'évaluation de la viabilité du projet, sont réalisées en parallèle sans véritable optimisation ni synergie avec l'ensemble des données disponibles. Cet article présente deux approches permettant d'intégrer certains types d'analyses aux modèles de blocs miniers. Ces approches permettent de quantifier la broyabilité du massif rocheux ainsi que d'étudier la stabilité des pentes minières à même les outils d'optimisation et de planification minières. Cette méthode permet dès l'étude de faisabilité d'un projet minier de maximiser les données disponibles, menant ainsi à une approche plus intégrée en conception minière. De plus, ces approches sont flexibles et permettent d'évaluer rapidement plusieurs scénarios, tout en laissant la possibilité de bonifier le modèle et de revoir la conception tout au long du projet minier.

Jan 1, 2010

By Alfred Traverse

The Brandon lignite is a small deposit of very low rank coal near the village of Forestdale in the town of Brandon, Vt. It occurs in association with other sediments, principally sands and silts. This lignitic coal has attracted considerable scientific interest since the middle of the 19th century because of the abundance of fossils in the sediment and the rarity of lignite in New England. A cooperative investigation has been developed by E. S. Barghoorn, W. Spackman, and the author in which different phases of the problem have been worked on in a coordinated research program. This paper presents results of an investigation of the very abundant fossil pollen and spores and some other microfossils of the deposit. The studies on which this manuscript is based were made in large part at Harvard University in partial fulfillment of the requirements for a Ph. D. degree.

Jan 1, 1955

Norton Co., the world's largest producer of abrasives, is enlarging its proppant operation. Proppants are strong chemical particles used to wedge open rock formations in deep oil wells, thereby increasing the well flow rate, sometimes as much as tenfold. Norton" aluminum oxide-based proppant is rapidly displacing less durable materials. The company is building the world's largest proppant plant in Fort Smith, AR. ALUMINUM--See also REFRACTORIES The price of primary aluminum ingot was increased by several producers in July. Kaiser Aluminum & Chemical Corp., and Revere Copper & Brass Inc. increased the price of primary aluminum to 63.0 cents per pound, effective July I. Reynolds Metal s Co., Anaconda Aluminum Co., Howmet Aluminum Corp., and Marti n Marietta Aluminum Inc. increased the price of 99.5% primary aluminum ingot to 63.0 cents per pound, effective July 5, The Aluminum Company of America increased the price of aluminum ingot to 62.5 cents per pound, effective July 9. The range of prices at the end of the month was 58.5 to 63.0 cents per pound.

Jan 1, 1979

By Douglas W. Fuerstenau, Pradip Pradip

The design and development of selective flotation collectors has been the key to the remarkable success of flotation in beneficiating complex, difficult-to-process ores. Sustained research efforts in the field over the past hundred years have led to delineating the scientific basis of selective mineral flotation in terms of the crystal chemistry and the surface and colloid chemistry of minerals including their solubility, and the aqueous solution chemistry of added reagents. It is now well-established that the electrical double layer theory (EDL) is the most powerful means of quantifying the relative strength of mineral-reagent interactions in the case of nonsulfide minerals. We illustrate the utility and the power of the EDL in delineating the science underlying selective mineral flotation with the help of a few examples taken from our own work, in particular on the selective flotation of rare-earth minerals (bastnaesite) from associated semisoluble minerals (barite and calcite) using alkyl hydroxamate collectors and the flotation separation of lithium-containing minerals (spodumene) from associated alumino-silicate minerals with oleate (fatty acids). Both of these mineral separation systems are of contemporary research interest and of immense value to the industry today. Recent advances in utilizing molecular modeling computations, particularly in the context of quantifying the effect of crystal chemistry and the relative distribution of adsorption sites available on mineral cleavage planes, are also reviewed.

By Bradford F. Townsend, Marc R. Kritzer, Michael F. Roach, Dennis Ofiara

All Rights Reserved. Printed in the United States of America. Information contained in this work has been obtained by SME, Inc. from sources believed to be reliable. However, neither SME nor its authors guarantee the accuracy or completeness of any information published herein, and neither SME nor its authors shall be responsible for any errors, omissions, or damages arising out of use of this information. This work is published with the understanding that SME and its authors are supplying information but are not attempting to render engineering or other professional services. If such services are required, the assistance of an appropriate professional should be sought. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of the publisher. Any statement or views presented here are those of the authors and are not necessarily those of SME. The mention of trade names for commercial products does not imply the approval or endorsement of SME.

Dec 1, 2008

By J. W. Latilla, J. J. van Wijk

A running facebreak ahead of the powered support units occurred on the number 4 seam at Matla Coal’s number 3 shaft (Matla 3) in April and May 2002.Very difficult mining conditions were experienced for a distance of some 150 m in the tailgate and to a lesser extent on the face itself. The paper analyses the main causes for the high stress conditions leading to the facebreak, namely, the existence of a >20 m dolerite sill close to surface and the effect of stopping longwalling on the overlying 5 seam. Difficulties experienced during the facebreak are discussed, including, pillar and roof collapses in the tailgate, high stress areas ahead of the face causing roof and sidewall stability problems, flushing of broken rock into the face area at the tailgate, secondary mid-face breaks, and the availability of critical support units. Successful rock engineering interventions and learning points were that, a goaf angle of 14.6° was found to be more realistic than the previously used 20 to 25° in predicting dolerite sill behaviour in this area, pre-split blasting of the sill significantly reduced stress on the face and tailgate allowing re-support work to proceed, varying pillar support types were analysed and rated, the need to always have a ground control “First Aid” kit available was recognised and a strategy for subsequent panels beneath the sill was developed. Numerous support units were used and the performance of the more suitable types is briefly discussed. A running facebreak ahead of the powered support units occurred on the number 4 seam at Matla Coal’s number 3 shaft (Matla 3) in April and May 2002.Very difficult mining conditions were experienced for a distance of some 150 m in the tailgate and to a lesser extent on the face itself. The paper analyses the main causes for the high stress conditions leading to the facebreak, namely, the existence of a >20 m dolerite sill close to surface and the effect of stopping longwalling on the overlying 5 seam. Difficulties experienced during the facebreak are discussed, including, pillar and roof collapses in the tailgate, high stress areas ahead of the face causing roof and sidewall stability problems, flushing of broken rock into the face area at the tailgate, secondary mid-face breaks, and the availability of critical support units. Successful rock engineering interventions and learning points were that, a goaf angle of 14.6° was found to be more realistic than the previously used 20 to 25° in predicting dolerite sill behaviour in this area, pre-split blasting of the sill significantly reduced stress on the face and tailgate allowing re-support work to proceed, varying pillar support types were analysed and rated, the need to always have a ground control “First Aid” kit available was recognised and a strategy for subsequent panels beneath the sill was developed. Numerous support units were used and the performance of the more suitable types is briefly discussed. Une cassure de taille en avant des unités de soutènement s’est produise sur la veine numéro 4 dans le puits numéro 3 (Matla 3) de la mine Matla Coal en avril et mai 2002. Les conditions d’extraction étaient extrêmement difficiles sur une distance d’environ 150 m dans la voie de tête et, en moindre mesure, sur le front de taille lui-même. L’étude présente analyse les raison majeures pour les conditions de grandes contraintes qui ont conduit à la cassure de taille, à savoir l’existence d’un mur de dolérite de >20m proche de la surface et l’effet d’arrêter la longue taille sur la veine 5 superposée. Les difficultés rencontrées pendant la cassure de taille sont rapportées, y compris les effondrements de piliers et toit dans la voie de tête, les aires de grandes contraintes en avant du front de taille causant des problèmes de stabilité pour le toit et les parois latérales, l’injection de roches cassées dans la taille en voie de tête, les cassures secondaires à mi-taille, et la disponibilité d’unités de soutènement critiques. Interventions minières réussies et leçons apprises furent : un angle de remblai de 14.6° était plus réaliste que celui de 20 à 25° utilisé auparavant pour prédire la conduite du mur de dolérite dans cet endroit ; tir à deux temps du mur a réduit considérablement les contraintes sur la taille et la voie de tête, ce qui a permis un travail de support complémentaire ; des types variés de support de piliers furent analysés et évalués ; la nécessité d’avoir toujours une trousse de première urgence disponible fut reconnue ; et finalement une stratégie pour les panneaux en dessous du mur fut

Jan 1, 2003

By A. Fahimifar, H. Soroush

Abstract: Triaxial tests were conducted on the schist specimens with various anisotropic angles under confining pressures of 0, 7 and 15 MPa, and axial stress-axial strains, were measured and plotted for various conditions. The results obtained reveal the effects of schistose on the strength and deformability of the rock very clearly. Peak strength of the specimens for 00 and 900 schistose orientations are nearly the same. Modulus of elasticity of this rock varies with anisotropic angle. For 0 orientation modulus of elasticity increases to a maximum. Confining pressure increases the peak strength and improves the rock deformability. However, this effect is not the same for various orientations, and there are no similar trends for each anisotropy direction. Analysis of the results shows that consideration of a linear failure criterion such as Mohr-Coulomb is appropriate for the prediction of rock behaviour up to 10 MPa, rather than a non-linear one. The analysis also reveals that the friction angle and cohesion are affected by the anisotropy orientation, and this effect is more important for the cohesion than the friction angles. Resume: Les esseys triaxiales sur les echantillon d un roch schist avec les differents angles non-isotrop sous les tension lateral zero et sept et qoinze mega pascal (mpa) est fait et les covtraite et allongment unitaire sont mesure et leur curues est destine sous different condition les resultats obtenues montre les effets du schistosite sur le resistance et le ductilite vissiblement. Le resistance final sur les echantilions pour les angles o degre et 90 degree est equivalent. Le modoule d elasticite de ce roch sera difere par a port de l angle de stratification. Pour l angle o degree le valeur de modoule est le maximum. le pousse lateral augmenterai le resitance final, et sera amilterai le toleran le de ductilite. Mais cette effet bn est pas unigue pour les different stratification, et pour les diferents directions no– isotrop it n y a pas le meme solution. L analyse des resulitats montre que le criterre de ruin comme mohr–colomb est moderate pour le pousse lateral jusq av lo mega pascal , et ce n est pas neccesaire d utiliser de criterre no–linear . Cette analyse aussi montre que l angle de frottement et cohsion est en relation de la direction no–isotrop, et cette effet est olus important pour le cohsion par a port de l angle de frottement . Abriß : Dreiachsige Prüfung wurde auf den schist Exemplaren mit verschiedenen anisotropic Winkeln unter Bestätigen von Drücken von 0.7 und 15 MPa geleitet, und axiale Spannung axiale Spannungen, wurden gemessen und für verschiedene Bedingungen wurde geplant. Die Ergebnisse haben die Wirkungen von schisocity auf der Kraft und dem deformability des Felsen sehr deutlich erhalten offenbart. Maximale Kraft der Exemplare für 0° und 90 sind° schistos Orientierungen beinahe das gleiche. Modulus der Elastizität von diesem Felsen ändert sich mit anisotropic Winkel. Für 0° vermehrt Orientierung modulus der Elastizität zu einem Maximum. Einschränkender Druck vermehrt die maximale Kraft und verbessert den Felsen deformability. Aber ist diese Wirkung nicht das gleiche für verschiedene Orientierungen, und es gibt keine ähnlichen Tendenzen für jede anisotropic Richtung. Analyse der Ergebnisse zeigt jener Überlegung Kriterium eines linearen Ausfalls wie zum Beispiel Mohr Coulomb passend für die Voraussage von Felsen Verhalten bis zu 10 MPa, anstatt eines nicht linear ist. Die Analyse offenbart auch, daß der Reibung Winkel und Bindekraft werden beeinflußt von der anisotropic Orientierung, und diese Wirkung wichtiger für die Bindekraft ist, als der Reibung Winkel

Jan 1, 2003

By G. Van Weert

In the spring of 2010 double refractory ores from historical stockpiles were processed through Barrick's Goldstrike pressure oxidation facility, thereby providing preg robbing feeds for a variety of metallurgical testwork. This paper describes the effects of amount, type, place and time of addition of activated carbons on CIL gold recovery and shows that native carbon in plant PDX'ed discharge solids can still preg rob gold loaded activated carbon.

Jan 1, 2011

Jan 1, 1994

By N. Morrison, I. Holl, R. Welyhorsky, A. Hempstock

ABSTRACT: The Victor diamond mine is located in the James Bay lowlands, 90 km west of the First Nations village of Attawapiskat. The project was the first of its kind in northern Ontario. The process plant was designed to produce a 95 to 98% by weight diamond concentrate through three stages of comminution, dense medium separation, and proprietary X-ray technology for final recovery. The plant was commissioned over a period of six months, commencing prior to substantial completion of construction. Through effective planning of the commissioning phase, the Victor mine start-up was safely completed nine months ahead of schedule.

Jan 1, 2011

By D. L. Koch, J. W. Tester, L. K. Sinclair

"In this study, hydraulic conductivity (K) geostatistics were used to predict residence time distribution of well-to-well flow. Flow profiles, fracture density measurements, and pumping tests were available from the highly fractured Florence Copper in situ leaching site. The flow profiles were used to establish the statistical distribution and spatial autocorrelation of K. Two tests were used for validation. The first test confirmed that fracture density and K are autocorrelated over similar length scales. In the second test, Monte Carlo flow simulations successfully recreated the results of pumping tests. Flow sim¬ulations were used to stochastically model well-to-well residence time distribution. RÉSUMÉ Dans cette étude, nous utilisons la géostatistique de la conductivité hydraulique (K) pour prévoir la distribution des temps de séjour (DTS) de l’écoulement entre les puits. Des profils de l’écoulement, des mesures de la densité des fractures et des essais de pompage existaient pour le site fortement fracturé de lixiviation in situ de Florence Copper. Les profils de l’écoulement ont permis d’établir la distribution statistique et l’autocorrélation spatiale de K. Deux essais ont servi à la validation ; le premier a confirmé que la densité des fractures et K sont autocorrélés sur des échelles de longueur similaires ; quant au second, des simulations d’écoulements de type Monte Carlo sont parvenues à reproduire les résultats des essais de pompage. Les simulations d’écoulement ont servi à établir un modèle stochastique de la DTS de l’écoulement entre les puits.INTRODUCTION In situ leaching is the circulation of a dilute acid or base solution in the subsurface, via a series of injection and recovery wells, to dissolve a target metal. In situ leach modelling requires forecasting the residence time distribution (RTD) of flow between wells. In fractured formations such as copper porphyry deposits, order-of-magnitude variations in hydraulic conductivity (K) can result in highly channeled flow, resulting in a heavy tailed RTD (Becker & Shapiro, 2003; Kang, Le Borgne, Dentz, Bour, & Juanes, 2015). Channeling through preferential pathways has impacted copper recovery at several past in situ leaching field tests (Cathles, Glenn, Lenzi, Nigrini, Deans, & Huff, 1978; Ahlness & Pojar, 1983; Schmidt, Earley, & Friedel, 1994; Sinclair & Thompson, 2015). The aim of this work is to combine multiple types of hydrogeological measurements to stochastically forecast the well-to-well RTD in fractured rock for the purposes of copper in situ leach modelling."

Jan 1, 2018

The 1969 Lignite Symposium was held at Grand Forks, N. Dak., on May 1-2, 1969. Cosponsored by the University of North Dakota and the Department of the Interior, Bureau of Mines, the meeting was the fifth in this series. Registrants from many States and Canadian Provinces attended the meeting representing many segments of energy-oriented companies, State and Federal Government, and universities. At 2-year intervals, these symposia provide a common meeting place where recent research and developments in technology and utilization of energy resources with emphasis on solid fuels (lignite) are presented. Proceedings3 of the previous symposia including a Forum held in 1958 have been published.4

Jan 1, 1970

By G. W. Josephson

JUDGING by the progressive atmosphere prevailing in the nonmetallic mineral industries during the past year, postwar conditions were healthful though inflationary. Demand for most industrial mineral products has been exceptionally high and many new production records were attained. Severe shortages of some commodities existed, especially building materials and fertilizers. Production costs and prices increased and profitable operation was general. Under these conditions expansion programs were the order of the day. Ample funds were available to finance the purchase of good equipment; and, as wages and other operating costs were increasing, primary emphasis was placed on attaining maximum efficiency in new installations. These efforts were hampered by shortages and slow delivery of desirable equipment, so compromises in design were often necessary. However, on the whole, production practice improved.

Jan 1, 1948

By C. A. Geffen-Fowler

This report, sponsored by the Bureau of Mines, presents the results of an examination of the safety of the Blind Shaft Borer (BSB) shaft sinking system and an alternative modified BSB design concept in comparison to conventional shaft sinking technology. Detailed study of the two systems was also performed to identify and recommend design changes for optimum safety conditions. A comparison of the BSB systems with conventional shaft sinking was made on the basis of relative risk levels. Risk incorporates both the frequency and the potential consequence of accidents. A safety evaluation of the component operations of the two BSB systems was performed using a Failure Modes and Effects Analysis (FMEA) methodology. The results of this analysis show generally that both BSB systems are safer than conventional shaft sinking. The potential risk of conventional shaft Sinking operations could be reduced by over 30%, on the average with the use of the original BSB system, and by an average of about 10% with the modified BSB. Design change recommendations to further improve the safety of these systems include a better fire suppression system, improved man haulage systems and more compact hydraulics. An operational safety manual was also developed for the modified BSB system.

Jan 1, 1981

In response to increased aluminum demand, U.S. producers have begun reactivating primary aluminum capacity which was shutdown during the 1974-1975 recession. Reynolds Metals Company started up almost 80,000 tons per year of idled capacity at Listerhill, Alabama, and Jones Mills and Arkadelphia, Arkansas plants. Howmet Aluminum Corporation and Alumax announced that the operating rate at their jointly owned facility at Frederick, Maryland was being increased from 75 percent to 100 percent, equivalent to a 44,000 ton-per-year increase in output. Kaiser Aluminum and Chemical Corp. expected to restart one of the two idled potlines at its Mead, Washington facility in May raising its production rate by 27,000 tons per year. ANTHRACITE - The anthracite market for the larger sizes continues at a good level, and although the demand for industrial sizes has been weak, the current trend indicates an increased demand for industrial fines by the steel, auto, and other industries.

Jan 1, 1976

Workers at the Consolidated Aluminum Corp. primary aluminum smelter at Lake Charles, LA walked out at midnight March 31 when their contract expired. Management personnel operated the smelter and prebaked carbon anode facilities until an agreement for a new 3-year contract was reached April 18. The Aluminum Company of America (Alcoa) began operations at its can recycling facility at Taylor, MS. The facility can process 3 million pounds per month of aluminum and steel cans. Alcoa announced plans to increase the capacity of its aluminum paste and flake production plant at Logan's Ferry, PA by 50 percent. Completion was scheduled for mid-1980.

Jan 1, 1979