Search Documents

By D. L. Cluff

Ventilation Air Methane (VAM) is a high volume low concentration methane source. The capture or use of methane from VAM is challenging, which results in the routine discharge of methane into the atmosphere. Mitigating VAM has the benefits of providing an energy source and reducing the atmospheric Greenhouse Gas (GHG) burden. The GHG radiative forcing effect of methane is 17?23 times as potent as carbon dioxide on a 100-year time horizon. Thus, any reduction in atmospheric methane would be beneficial. The calorific value of methane is 55.5 MJ/Kg; therefore, a 100 m3/s flow with VAM concentrations from 0.1?1% can provide 3.8?38 MW of exploitable power. Strategies to mitigate VAM such as: Thermal Flow Reverse Reactors (TFRR), Catalytic Flow Reverse Reactors (CFRR), Lean Burn and Catalytic Gas Turbines, Biothermica Vamox®, Megtec VOCSIDIZER©, and Vamcat? are briefly reviewed. The review of VAM mitigation technologies reveals disadvantages such as the need to maintain a minimum internal heat capable of oxidizing the methane. This requirement uses all of the available methane up to the point of reaction sustainability and up to half at the highest methane concentration in VAM. Some systems may introduce a pressure drop to the ventilation system, which would impinge on the existing ventilation system design. These impediments necessitate the development of a more amenable technology. In the proposed system, gas turbines (GT), coupled to a combustion chamber with an external fuel supply, assist the combustion of the VAM. The combustion-chamber coupled system provides electricity, while the heat contained in the GT exhaust gases increases the temperature of the VAM, encouraging the development of a flame inside a combustion chamber. The flow from the combustion chamber streams through a primary air/fluid heat exchanger capable of producing steam of a high enough quality to generate electricity using conventional steam turbines. The residual heat after primary extraction, directed through other equipment, provides additional heat based products such as industrial scale dry air, chilling by an absorption chiller or hot water. The overall design of the system is scalable for low to high VAM flows or variations in concentrations and is capable of providing the company or community with heating, chilling, hot water, electricity or motive force as needed by the particular site or community. The Multi-generation system uses heat from three sources to provide clean efficient energy while mitigating the atmospheric emissions of methane. These sources are heat from the GT, often considered waste heat, heat from fuel injected into the igniters and heat from the VAM. The opportunity to collect carbon credits may improve the economics. In order to design a system with this capacity, a detailed analysis of the combustion characteristics of three separate flows is required. VAM is the main airflow, having the highest volumetric effect, while the GT exhaust and the additional fuel added to the hot exhaust flow of the gas turbine are lower flows, but have a higher velocity and temperature. The aim of the modeling undertaken in this work is to establish the combustion dynamics, degree of pre-heating required and the geometry essential to the design of combustion based VAM mitigation multi-generation systems.

Aug 1, 2013

By A. Halim, A. Martikainen, S. GYAMFI

This paper outlines a unique case of the development of strategies to reduce ventilation and heating costs in Konsuln iron ore mine in northern Sweden. The mine, located just south of Luossavaara-Kiirunavaara Aktiebolag’s Kiruna iron ore mine, was developed as a test mine from 2018-2020 for the Sustainable Underground Mining (SUM) project. Besides functioning as a test mine, Konsuln also contributes to ore production. The existing mine ventilation system was designed for the current production rate of 0.8 million tons per annum (Mtpa). There is a plan to increase this rate to between 1.8 and 2.0 Mtpa.

Sep 30, 2021

By James R. Wait

An attempt is made here to collect together various reports and publications that are based on research supported all or in part by Contract No. H0155008 for the past two years. The subject matter deals primarily with the excitation, transmission, and reception of electromagnetic waves in mine environments. This contract from the U.S. Bureau of Mines with the Office of Telecommunications supports the efforts of James R. Wait (Principal Investigator and Consultant to OT), David A. Hill (Co-Investigator), and various associates within the Boulder scientific community. The contributions of Samir F. Mahmoud were supported, in part, by the contract while he was a Visiting Fellow with the Cooperative Institute for Research in Environmental Sciences at the University of Colorado. Administrative assistance in CIRES has been provided by Mrs. Lana R. Hope.

Jan 1, 1976

By A. C. Fieldner

This is the tenth annual report of research and technologic work conducted by the Bureau of Mines on the occurrence, properties, mining, preparation, and uses of coal and coal products. These annual reviews are guide's to the current work-and publications of the Bureau but do not replace the more complete reports published under the authorship of the individual investigators on specific problems in Bureau of Mines bulletins, technical papers, reports of investigations, and information circulars and in the technical press. The Annual Report of the Director of the Bureau of Mines to the Secretary of the Interior for the Fiscal Year ended June 30, 1945, summarizes the year's work on coal as follows: Coal and Coal Products The United States maintained its No. 1 industrial position in supplying fuel for war and in preparing for peace through more complete mining, improved preparation and up-grading of coal for special uses, and better utilization of coal in industrial establishments and homes.

Jan 1, 1946

By E. Lee Bray

"Editor’s note: The editors thank those who make this annual issue possible. A special thank you goes out to the Industrial Minerals Annual Review editor, to the Industrial Minerals & Aggregates Division Technical Committee chair and vice chairs, and to the authors of the individual commodity profiles.Jim Norman, member SME, of Tetra Tech Geo, is the industrial minerals annual review editor. Edgar Blanco, member SME, of Freeport- McMoRan, is chair of the Industrial Minerals &Aggregates Division’s Technical Committee.The technical committee vice chairs include:• NickTushar Gupta and Sallie Gaillard, of the USGS, members SME, agricultural materials.• Abhishek Choudhuryand Xihui Yin, members SME, of Montana Tech and Kemira, repectively, ceramic and refractory materials.• Bobbi Strange and Riddhika Jain, members SME, of Outotec, Martin Marietta and Outotec, respectively, chemical raw materials.• Snehamoy Chatterjee, Alyssa Kendir and Alind Chandra, members SME, of BMT, Universityof Kentucky and Michigan Tech, respectively,construction aggregates.• Subham Verma, Gauran Soni and Freddy Sime, members SME, fillers and pigments.• Kaiwu Huang, Thomas Hilderbrand and Ricardo Santander members SME, of Virginia Tech, Thiele Kaolin and Carbo Ceramics, respectively, sorbents, filters and process aids.• Rhaghay Dubey and William Rapier, members SME, of Outotec and a consultant, respectively, specialty minerals.On behalf of ME readers, the editors thankTwo U.S. alumina refineries produced an estimated 1.5 Mt (1.65 million st) of alumina from imported bauxite in the United States in 2018. The 500-kt/a (550,000-stpy) refinery in Burnside, LA, owned by Almatis Inc. produced specialty alumina used in the abrasives, ceramics, chemical and refractory industries. The 1.2-Mt/a (1.32 million-stpy) refinery in Gramercy, LA, owned by Noranda Alumina LLC produced alumina mostly for use in aluminum smelters but also produced specialty alumina. An upgrade project at the Gramercy refinery to convert 200 kt/a (220,000 stpy) of capacity to produce more profitable specialty alumina was completed in the first half of 2018, and another project to increase capacity was started but a completion schedule was not available. The amount of new capacity was not disclosed, but it would be used to produce nonmetallurgical grade alumina. The 2.3-Mt/a (2.5 million-stpy) refinery in Point Comfort, TX, which was temporarily shut down in March 2016, remained closed throughout the year."

Jul 1, 2019

By Richard W. Lusignea

This report describes a program to evaluate the feasibility of determining roof features which occur in United States coal mines from changes in bolting machine drilling parameters. The ultimate purpose of this effort is the development of an instrumented roof bolting machine which can detect hazardous roof conditions and/or indicate when the existing roof control plan is inadequate. A survey of hazardous conditions occurring in United States coal mines is included, along with the slang expressions for these conditions, and their relative degree of hazard. Specific machine parameters are identified for detecting the specific roof conditions. Measurement concepts are proposed using readily available instrumentation in most cases. Various systems are evaluated and tradeoffs presented. An implementation plan is proposed for developing a prototype system and using it in an operating coal mine.

Jan 1, 1978

Consumption and intensity of use trends for twelve metals, by industrial end use, were estimated for 1972 through 198Z. The trends were then forecast through 1993 using standard statistical methods. The intensity of use measure selected is the quantity of metal consumed per constant dollar output of a specific industrial sector. The metals studied were aluminum, chromium, cobalt, copper, lead, manganese, nickel, the platinum-group metals, tin, titanium, tungsten, and zinc. Average annual growth rates for the following four of the twelve metal increased from 1972-82 as follows: aluminum, 1.00 percent; platinum-group metals (consisting of platinum, palladium, and iridium), 8.83 percent; titanium, 7.82 percent; and tungsten, 6.09 percent. Consumption. for the remaining eight metals decreased at average annual rates ranging from 0.58 percent (copper) to 5.37 percent (manganese).

Jan 1, 1986

Jan 1, 2002

This: symposium was sponsored by the Bureau of Mines, U.S. Department of the lnterior, in order to critically examine the state-of-the-art of sulfide flotation chemistry and to define current and emerging problems that should be emphasized in future fundamental research. The topics covered through invited papers include both reviews and recent research results in the areas of thermodynamics of reagent-mineral interactions; collector adsorption processes; the effects of solid-state point defects on flotation; activation and deactivation phenomena; the electrochemical role of oxygen in sulfide flotation; environmental problems in flotation; and selective flocculation of fines. Papers riving perspectives on flotation research in relationship to our national mineral requirements and the relationships between industrial flotation research and academics are also presented. An edited summary of the symposium follows the papers.

Jan 1, 1980

By Persifor Frazer

1. SMOKE PREVENTION. Report of Select Committee of House of Commons (1843). Nuisance considerably abated in Leeds (Wm. Backerd, July 13, 1843, 239 pages). A synoptic index, p. 211, gives, in alphabetical order, the digest of every subject taken up. 2. FUEL : ITS COMBUSTION AND ECONOMY. D. Kinnear Clark, C. E. 24mo, 1354 pp. Crosby Lockwood & Co., London (1880). Includes abridgement of treatise on combustion of coal and prevention of smoke, by C. W. Williams, A.I.C.E. 3. DIE RAUCHSCHÄDEN IN DEN WÄLDERN DER UMGEBUNG DER FISCALISCHEN HÜTTENWERKE BEI FREIBERG. Dr. J. v. Schröder, Professor in Tharand, and Dr. A. Schertel, Vorstand des Hüttenlaboratoriums zu Freiberg. Royal 8vo, 27 .pages, 19 pages of tables and a map. Ernst Maukisch, Freiberg (1884). (Aus dem Jahrbuch für das Berg- und Huttenwesen, 1884.) In 1861, Reich and Stockhardt examined the extent of injury to vegetation by the Muldner works. Needles and twigs of pine showed in 100,000 parts : Pb, 5 to 50 ; As, 3.3 to 14.3 ; S02, 62 to 120. In the top twigs, 5 to 8 ; needles, 10 to 16 ; thicker twigs, 10 to 22 ; thinner twig-ends, 17 to 54 of lead. Lead greater in amount in sickly twig-ends with few needles ; also in the bark than in the naked wood of the trunk, which had hardly a trace ; also in the part turned toward the works than on the opposite side. Pb and As diminished in the vegetation with distance from the smelter ; and the same with regard to the soil. Fresh snow was collected, and SO, As, and Pb detected in it.

May 1, 1907

By Ernest A. Hersam

"INTRODUCTION.Luring the year 1923 a complete survey was made of the condition of research in the reduction (milling) and concentration of ores and nonmetallic minerals - that is, up to the stage where the ores or concentrates were ready for hydro- or pyro-metallurgical treatment. This survey was carried on under the general supervision of L. A. Lyon, assistant director and chief metallurgist of the Bureau of mines, in cooperation with the milling committee of the American Institute of mining and metallurgical Engineers, the Massachusetts Institute of Technology, and the University of California. Other institutions, including the National Research council, were of assistance and outlined recommendations during the study.While this report is on ""ore dressing"", it contains short sections on coal and clay. The mechanical handling that these minerals undergo is ""dressing"", so that ore dressing is inclusive of metallic and nonmetallic minerals. ""milling"", in its broadest sense, includes with ore dressing certain other metallurgical treatment which the report is not designed to cover.The survey revealed that considerable experimentation is being carried on great cost to the mining industry, but that the research is in general poorly coordinated while companies and firms are adequately taking care of routine tests and the mechanical features involved in their own operations, no comprehensive study of the fundamental principles of ore reduction is now in progress or contemplated. Many industries, besides mining, are interested in the preparation of materials for final treatment, rendering this investigation of value also to them. This class of fundamental research is neglected by industry unless there is some agency which can bring together at least a majority of this interested in a cooperative effort. It can not be effectively handled by a single company; and, moreover, no company can be expected to bear the whole burden of an investigation to benefit the entire industry or a number of industries hence there is need for concerted study within reasonable limits. Furthermore, co-operation eliminates duplication, which is largely a waste of effort and capital."

Mar 1, 1925

The value of raw nonfuel mineral materials production totaled an estimated $19.7 billion in 1978. The record 1978 value exceeded by 13 percent the 1977 value of $17.5 billion. This raw mineral output was the basis for approximately $200 billion worth of processed materials of mineral origin. Output of both metals and nonmetals increased about $1 billion each, above comparable figures for 1977. Of the 22 metals produced quantitative output of 11 increased and the value of 13 increased. Among the 48 nonmetallic commodities produced, the quantities for 35 increased, and the values for 40 increased.

Jan 1, 1979

By J. T. Dunham

Zirconium has possible use in industry where severe corrosion conditions are encountered because it resists attack from a variety of corrosive environments. However, very little experimental testing has been done to evaluate the corrosion behavior of zirconium when simultaneously subjected to high tensile stresses and exposed to corrosive environments. This investigation was initiated for an evaluation test, but was limited to environments consisting of ferric chloride solutions which were known to attack zirconium and were shown to promote stress-corrosion cracking in preliminary tests. Tests for cracking susceptibility were conducted by the Bureau of Mines to show the effect of stress, solution concentration, air aeration of solution, and the method of mechanical processing. Tensile stress was applied to the specimens by a constant-load method which proved more reliable than a constant-strain method.

Jan 1, 1961

By W. F. RITTMAN, E. W. Dean

This report presents the results of an investigation conducted by the Bureau of Mines for the purpose of assisting in the establishment of a satisfactory standard method for the analytical distillation of petroleum, a problem of great importance to the petroleum industry. Experiments were performed for the purpose of studying the charac- teristics of methods typical of those in use; comparative studies were made of the efficiencies of the principal types of fractionation ap- paratus available to the petroleum chemist; and the characteristics of a type of apparatus that the results of the experiments seemed to indicate was best adapted to the purpose were investigated in detail. Also, some experiments were made to determine the effect of cracking as a factor in the analytical distillation of petroleum in still heads.

Jan 1, 1916

By Owen Matthews

Introduction For the past year and a half, the mill of Cochenour Willans Gold Mines, Limited, McKenzie Island, Ontario has been roasting arsenopyrite-gold concentrates, prior to cyanidation, by means of a roaster employing techniques that are new and novel. The roaster is known as the Dorrco 'fluo-solids reactor', and the technique as 'fluidization'. The reactor has demonstrated its ability to roast a flotation concentrate containing arsenopyrite, pyrite, stibnite, small quantities of other sulphides, and some lime silicates and carbonates, yielding a calcine consisting mainly of porous iron oxide, plus the gold values. This calcine is readily amenable to cyanidation. Bulk shipments of concentrates to a distant custom smelter, as practised prior to this installation, has thus been eliminated, with appreciable savings in smelting charges, freight costs, and interest losses during shipment and smelting. This is the pioneer installation of fluo-solids roasting at a Canadian mill and up to the present performance results have not been published. It is the purpose of this paper to present the information now available for the benefit of other millmen who may be confronted with identical or similar problems to those encountered and solved at Cochenour Willans.

Jan 1, 1949

By Paul Billingsley

NICKEL Plate mountain coincides closely with that portion of the Hedley mining district which is of economic interest. From it has come almost the entire past production, and the active mines of the present epoch, Nickel Plate-Sunnyside and Hedley Mascot, lie in a compact group near its summit. The Hedley district, which is 210 miles due east of Vancouver, is situated in the Okanagan range of southern British Columbia, where this rather gentle uplift is deeply dissected by the canyons of the Similkameen and its tributaries. The region is essentially part of the Interior Plateau of the Province (Figure 1), but is adjacent to easterly elements of the Coast Range. The Similkameen canyon, 4,000 feet in depth and frequently less than 4 miles from rim to rim, traverses the district from northwest to southeast. The deepest and narrowest portion of the canyon lies between Hedley and Keremeos, 18 miles to the southeast. At Hedley, an important tributary, Twenty Mile creek, enters from the north in a bold canyon, making a focus of unusually rugged topography. Nickel Plate mountain occupies the sector to the east of this junction (see Figure 2) and its flanks are ringed by the cliffs of Twenty Mile canyon on the west and by those of the Similkameen canyon on the south. On the east, it slopes gently to the hanging valley of Eighteen Mile creek, and on the north, with only slight loss of elevation, it merges into the moderately hilly surface of the plateau.

Jan 1, 1941

By K. C. Dean

Discarded automobiles represent the greatest single resource of reusable metals, plastics, and rubber in the United States. This report presents results of Bureau of Mines research, conducted from 1965 to 1983, on separating and recovering useful materials from the scrapped hulks, using old and new metallurgical techniques combined with standard scrapyard methods. The Bureau determined the materials composition of three composite cars designated as circa 1960, mid-1970's, and early 1980's, and used these cars to study smokeless incineration and hand-sorting techniques. In studies on treating rejects from automobile shredders, the Bureau designed a process that included air classification, water elutriation, magnetic separation, handpicking, and heavy-medium separation, and also investigated cryogenics and liquation. Complete recovery of cop-per and other metals was economically made by hand and tool dismantling, leaching, or selective melting of starters and generators. Techniques are also discussed for plastic recovery and waste tire treatment.

Jan 1, 1985

By A. J. Kraemer

Few important improvements other than the development of cracking processes were made in technical petroleum refining from 1914 to 1919. Refiners were concerned mainly with enlarging their plants and erecting new plants to meet the growing demand for petroleum products. Shell stills operated as a unit or arranged in series for progressive or continuous distillation were the prevailing distillation equipment. Some improvement was made in condensers, but in most refineries of the period coils of pipe immersed in tanks of water were used to condense vapors and cool liquid products of the stills. Heat exchangers to conserve heat and reduce costs were more highly developed at California topping plants than at other plants. In this connection Wadsworth3/states: It is regretted that information concerning the operation of topping plants with eastern and Middle West oils is not available. The writer carefully canvassed the Middle West, but did not find a plant where operation had progressed beyond the early experimental stages and reliable figures could be furnished.

Jan 1, 1941

By L. G. Marshall

This report presents a cross section of the sand and gravel operations in the Minneapolis-St. Paul area. The study covers individual operations, economic problems peculiar to the industry, glacial geology of the area and its effect upon the grades and types of products, and past, present, and future trends of the expanding population and its effect upon the industry.

Jan 1, 1963

By L. G. Marshall

This report presents a cross section of the sand and gravel operations in the Minneapolis-St. Paul area. The study covers individual operations, economic problems peculiar to the industry, glacial geology of the area and its effect upon the grades and types of products, and past, present, and future trends of the expanding population and its effect upon the industry.

Jan 1, 1963