Search Documents

By Kenneth E. Hay

Researchers from the U.S. Bureau of Mines conducted a field study to assess the safety of remotely controlled mobile roof supports (MRS) in a retreat pillar mining operation, Data were collected to provide the Mine Health and Safety Administration with criteria needed to develop guidelines for MRS use and to determine if precursors could be identified that would alert miners to imminent roof falls. Two test sites at which two different support methods-MRS's and posts were used and were monitored to obtain information on entry stability. Pressure transducers and string pots were installed on all four MRS's to obtain loading and displacement information. and roof bolt load cells. sonic probes, extensometers, and survey targets were installed in the surrounding entries to obtain information on ground behavior. Results showed a larger increase in roof bolt loading and roof movement when MRS's were used, especially in the intersection area. Roof bolt loads in the entries showed decreases in load when the MRS's were set and increases up to 11,1 kN (2,500 lbf) when the MRS's were unloaded. Unloading of one MRS in a pair did not significantly increase load on the other. MRS's I and 2 usually had the higher loads, with these loads increasing as the pillars on each side were being mined. MRS 3 normally had lower loads than I and 2: however, it also experienced some very high loads when in the last position near the pushout. MRS 4 usually had the lowest loads, primarily because it was located near the solid pillar that was not being mined.

Jan 1, 1995

By Wen Tao Liu, Tong Tian, Fu Sheng Niu, Xiu Man Liang

In order to address the difficulty of accurate segmentation of froth images of different sizes, a method of froth image segmentation based on highlight correction and parameter adaptation is proposed. First, a machine vision system on a single-cell flotation machine is built to collect froth images. Homomorphic filtering is used to improve the uneven brightness and shadow of the images. Fuzzy c-means (FCM) clustering is then utilized to classify similar highlights that belong to the same froth. After Otsu threshold segmentation, a parameter-adaptive morphological operation is used to extract the marker points and edge bands and correct the froth edges in the original image. Finally, the modified image is filtered by morphological reconstruction, and the highlight mark is used as the local minimum point for watershed segmentation. Three sizes of froth images are segmented in comparative experiments. The results show that the proposed method is suitable for the segmentation of froth images of different sizes. The position of the extracted segmentation line is close to reality, with average over-segmentation and under-segmentation rates for froth images of 2.6% and 6.8%, respectively. The froth image segmentation performance is stronger than that of the other methods examined.

By Tassos Grammatikopoulos, Gary Pearse, Massoud Aghamirian, Charlotte Forstner, Stephen Mackie

"SGS Minerals Services (Lakefield, Ontario site) has conducted a number of developmental and pilot programs that examined methods for the beneficiation, extraction and recovery of lithium from a variety of spodumene containing hard rock sources. An overview of the beneficiation programs is presented separately by Aghamirian, Mohns, Grammatikopoulos, Imeson & Pearse (2011). The focus of this discussion will be the hydrometallurgical steps involved in producing a high grade lithium carbonate (Li2CO3) sample from the spodumene concentrate. SGS has applied the standard Li2CO3 hydrometallurgical flow sheet to a number of spodumene concentrates and has determined that all of these samples respond in a similar manner to the process and produce a final product having a Li2CO3 grade of >99.5%. The standard process is sufficiently robust to accommodate the observed variability in the concentrates that have been tested. Advantage of one spodumene deposit over another will thus be gained through process optimization and innovation. Optimization at the beneficiation stage and at the hydrometallurgical stage must be considered. Some aspects of the process optimization of the hydrometallurgical flow sheet will be presented.INTRODUCTION The current activity in the exploration, development, and mining of lithium based minerals is due in large part to the key role that this metal plays in the rechargeable battery industry (U.S. Geological Survey, 2011). Lithium battery technologies are widely applied in a range of portable electronic consumer products. The expanding development and production of hybrid and fully electric vehicles has contributed to the increased interest in finding and developing new lithium sources in order to meet the expected demand from the lithium battery industry. Lithium may be sourced from continental brines (sub-surface salars), hard rock minerals (pegmatite, spodumene), hectorite clay deposits, geothermal brines and oilfield brines. Currently the majority of the lithium products are produced from Li brines. The four major lithium producing countries are Chile, Australia, China, and Argentina (U.S. Geological Survey, 2009; Roskill, 2009). These countries accounted for 97.6% of the total lithium produced in 2010."

Jan 1, 2012

By Luis Haro

Puesto que el deslizamiento de relaves constituye uno de los principales riesgos para la vida y seguridad de los embalses, se desarrolló un programa que rehabilite los depósitos de los relaves a través de los gaviones y geomallas como elementos que estabilizan los relaves descargados. En este sentido, el uso de geosintéticos revolucionó el diseño de los relaves y sistema productivos y permitió un mejor manejo ambiental de los relaves. Asimismo, la utilización de gaviones como paramento externo en el sistema suelo armado, otorga mayor rigidez al mismo en el caso de paredes, taludes más verticales, drenaje y protección contra la erosión. En consecuencia, el uso de gaviones y geomallas es aplicable para la construcción de depósitos de relave y estabilización de depósitos inactivos.

Sep 13, 2001

By Maurice A. Ponti

The D.C. Water and Sewer Authority is implementing the Anacostia River Projects component of its Long-Term CSO Control Plan, including 21 kilometers of 3.7- to 7-meter-diameter CSO near-surface diversion storage/conveyance structures and flood relief, pressurized-face, soft ground tunnels at a maximum depth of 65 meters. This paper describes a project-specific soil grouping system that is primarily based on soil characteristics for tunneling derived from tests including Atterberg limits, grain size, swelling, mineralogy, triaxial, pressure meter, and consolidation, which differentiates the project from past area tunnel projects using descriptive systems based primarily on area geology.

By Emad Iskander

The seepage forces generated around pressurized water tunnels in rock are investigated using the analysis tools of geomechanics. The theoretical background of the two-phase material behavior is explained and the equations of motion and continuity are presented. Applications on two case studies typically occurring in practice deal with the required minimum rock cover for a pressurized tunnel and the separation between two tunnels carrying different heads. The rock mass behavior as described by the Mohr-Coulomb and Hoek-Brown material models is investigated by numerical analyses and the results are compared. The effect of key material parameters on the safety factors and the associated modes of failure is discussed.

Jan 1, 2008

By D. R. Zuchelli

In order for MSHA to require the use of a noise control, the control must be proven ?technologically feasible?. Technologically feasible controls must reduce a miner?s noise overexposure to the permissible exposure level (PEL) or achieve at least a 3 dBA reduction in the miner?s noise exposure. The miner?s total noise exposure should be examined from an occupational viewpoint and not solely on a machine or equipment basis. This examination requires a field evaluation of the occupation as opposed to an equipment test conducted in a laboratory. The operator of a Hilti TE MD20 LS electro-pneumatic drill realized a full shift noise exposure (TWA8) reduction exceeding 8 dBA as compared to when operating a Gardner Denver S83F pneumatic jackleg drill while installing an equal number of drill holes into the Idaho Springs Gneiss rock formation. However, the Hilti drill?s penetration rate was only 27% of that of the jackleg drill. Although the Hilti drill was proven to be technologically feasible as a noise control, its slower penetration rate would require its economic feasibility to be evaluated on a case-by-case basis.

Jan 1, 2011

By Adams F. C, Ridley K. L

Economic conditions after WorId War II made the recovery of Australian sources of sulphur one of considerable national importance. From 1947 to 1949 an investigation was made of recirculation techniques to produce acid plant grade gas from the Dwight-Lloyd down-draught sintering plant.During 1949 it appeared feasible to produce a gas of suitable 802 concentration and a decision was made to construct a gas purification train and a 150 tons/day contact acid plant. However, a number of difficulties remained in the production of the gases for sulphuric acid manufacture and as a result of research conducted to overcome these troubles the continuous up-draught sintering process was developed.The principal difficulties were:(a:) The down-draught sintering practice, as developed, produced an unusually high metallic lead precipitation in the windboxes. The disposal of this lead interrupted sintering operations and the delivery of gas to the acid plant.(b) The production capacity of the existing sintering plant was fully extended and the adoption of recirculation of gases, in an endeavour to satisfy acid plant requirements, would probably reduce the plant production capacity.(c) The prevailing high temperature of water available for purification train cooling required a higher than...

Jan 1, 1956

By A. D. Hammond

"INTRODUCTION The recent drop in iron ore prices has claimed an unwitting casualty in vanadium. Vanadium is dominantly produced as a co-product of steel production. The recent shutdown at EVRAZ’s Mapochs steel-vanadium operations in South Africa has cut-off 10% of the world’s vanadium output. Earlier in February, 2015, Australia’s Atlantic Ltd. suspended operations at its Windimurra iron-vanadium complex after a fire caused severe damage at the plant. Since then, challenging market conditions has resulted in the permanent closure of this operation. This decoupling of vanadium production from integrated iron ore producers presents an opportunity for vanadium exploration companies to target single-product deposits. This trend is manifested in the increasing number of pure-play vanadium ventures around the world.The mine production of vanadium is dominated by three countries namely, China, South Africa and Russia, which collectively produce 98% of the world’s vanadium. While the use of vanadium as an alloy in the steel industry remains by far the largest application for this metal, growth in demand is expected to come from the renewable energy industry in the form of batteries for energy storage. This paper summarizes the current state of vanadium exploration, briefly describes the vanadium market and lists sources of future demand for the metal. TREND IN VANADIUM EXPLORATION The most active participants in the current vanadium exploration are pure-play vanadium ventures in Brazil, South Africa and Australia. These ventures are targeting deposits with higher vanadium grade than those typically mined in titaniferous magnetite operated by integrated steel-vanadium producers. The 10% shortfall in vanadium production resulting from the shutdown at EVRAZ’s Mapochs is expected to be partially compensated by Largo Resources’ Maracás Menchen vanadium operation located in the State of Bahia in Brazil, which commenced operation in August 2014 and is expected to reach design capacity of 11,400 tonnes of vanadium pentaoxide (V2O5) by the end of 2015. The estimated production1 for 2015 is 6,500 tonnes of V2O5 at a target production cost of $3.60/lb. This is the first vanadium operation to be placed in production in the Western Hemisphere in over 35 years."

Jan 1, 2016

By Julie Dénommé

Today few in business would argue with the idea that we are living in a world that is Volatile, Uncertain, Complex, and Ambiguous. Coined VUCA by the US Army War College, these four words define the ?turbulence? and ?continuous white water? that the business literature has been documenting for the last decade. This VUCA world became even more relevant to business in 2007 when the Institute for the Future fellow Bob Johansen published the idea of transforming VUCA into Vision, Understanding, Clarity, and Agility. We call this VUCA Prime (VUCA'), and place an infinity loop (8) between them to show their dynamic interaction. This paper presents an exploration of the impact of VUCA 8 VUCA' on business and the conditions under which these dynamic forces help to successfully navigate change.

Oct 1, 2010

By Linda L. Chasko, Charles P. Lazzara, Gary Braselton, Ronald S. Conti

Preparedness is an important element of any underground mine's strategic plan in dealing with an unexpected event, such as a fire. A fully implemented fire preparedness and response plan is essential in reducing the probability and seriousness of a mine fire. This report describes the development of an underground coal mine fire preparedness and response checklist (MFPRC). The checklist is a data collection instrument for profiling both the fire prevention and response capabilities of a mine site and usually requires 3 to 4 days to complete. The checklist encompasses conditions, procedures, and equipment that have frequently been identified as the primary or contributing causes of underground coal mine fires. At least 1 day is needed underground to evaluate the water system. This entails measurements of water flows and pressures at fire hydrants, and water throw distances of fire hose and nozzles at several locations (mains and branch lines). A few of the other topics that are discussed with mine personnel include detection and suppression systems, combustible materials, mine rescue and fire brigades, and firefighting equipment. The MFPRC was developed by the National Institute for Occupational Safety and Health (NIOSH),Pittsburgh Research Laboratory. Under a Cooperative Research and Development Agreement (CRADA) with Cyprus Amax, Twenty mile Coal Co. (Oak Creek, CO), the checklist was field tested and further refined. Additional field tests were conducted at several other operating coal mines.

Jan 1, 2000

By Gustavo Quiquia Mucha

El presente texto describe las experiencias realizadas por la Compañía Minera Milpo SAA en el marco de una gestión social basada en la consulta previa, libre e informada en la Exploración Minera Responsable. En ese sentido, es importante la cooperación entre la empresa minera y la comunidad, así como la incorporación del marco ideológico empresarial y metodológico, basado en los principios del Convenio 169 de la OIT sobre Pueblos Indígenas y Tribales en Países Independientes, las estrategias y las líneas de intervención social de la Compañía Minera Milpo SAA en los proyectos de exploración minera responsable.

Sep 12, 2011

By Kumar A, Mishra N. C

For each tonne of chromite ore mined in Sukinda, approximately ten tonnes of fine overburden material is generated. The overburden typically contains about 30 - 60 per cent Fe2O3, 0.3 - 1.1 per cent Ni, four to nine per cent Cr2O3 and 0.04 - 0.2 per cent cobalt and is being discarded leading to loss of valuable metals and creating environmental pollution. In order to take the advantage of presence of iron, nickel and chromium, the present studies advocate the utilisation of nickel lateritic chromite overburden for production of Ni bearing pig iron through blast furnace extracting maximum iron and nickel from the chromite overburden. The present paper deals mainly with the beneficiation of chromite overburden, sintering characteristics and thermodynamic studies. The beneficiation study shows that a beneficiated concentrate having Fe - 50 per cent and Ni -- 1.1 per cent can be achieved from chromite overburden having Fe - 30 per cent and Ni -- 0.7 per cent. Sintering studies have been carried out with bed height of 300 and 450 mm at a suction of 600 and 900 WG respectively. The results reveal that good quality sinter can be produced from chromite overburden concentrate with a basicity of about 1.0 and coke breeze consumption rate about 16 per cent. In all the experiments, Tumbler Index, Abrasion Index and Shatter Index was found to be in the range of 65 - 70, 4.5 - 5.5 and 85 - 90 respectively. The other parameters namely softening temperature, melt down temperature, reduction degradation test and relative reducibility have also been determined. A thermodynamic analysis has also been carried out to make a technological assessment of the process for the production of alloyed pig iron from chromite overburden in blast furnace which shows that it is possible to produce nickel bearing pig iron in blast furnace using the sinter up to 80 per cent. Techno-economic analysis reveals that this route will yield a substantial profit even after accounting for cost of beneficiation, extra coke, raw materials and extra slag produced.

Jan 1, 1999

By Robert W. Smith

[In a certain application it was necessary to compute the incomplete beta function, ß(1/2, p, q), for a certain set of values of p and q. Since the set of p and q values was much more finely spaced than those in any published tables, the authors have decided to make their results available in this report. In connection with this application, the function ß(1/2, p, q) was needed at various points in the p, q plane at intervals of 0.05, 0.05 p = 2q < 10.00. Fletcher, Miller, and Rosenhead3/ state that the only tables available in the desired range are those of Pearson.4/ However, the interval used by Pearson was not small enough for the present application. For this reason, it was decided to calculate the function ß(1/2, p, q) for p = q = 0.05 (0.05) 10.00. This table is published because of the fundamental importance in mathematical analysis of the incomplete beta function.]

Jan 1, 1953

By AIME AIME

COMMITTEES. CANAL ZONE.-Col. George W. Goethals, U. S. A., Chairman; Lt.-Col. H. F. Hodges, U. S. A. ; Lt.: Col. D. D. Gaillard, U. S. A. ; Lt.-Col. William L. Sibert, IT. S. A. ; H. H. Rousseau, U. S. N.; Col. W. C. Gorgas, U. S. A.; Maurice H. Thatcher ; Joseph Bucklin Bishop ; Lt.-Col. Charles F. Mason, U. S. A.; S. B. Williamson ; Major Eugene T. Wilson, U. S. A. ; Edward Schildhauer ; Henry Goldmark ; Edward C. Sherman ; W. G. Comber ; W. B. Corse ; J. A. Walker; Joseph A. Le Prince; J. A. Smith ; Lt. Frederick Mears, U. S. A. HAVANA.-V. T. Polledo, Chairman; Diego Lombillo Clark, Jose Primelles, J. R. Villalon, Jose Artola, J. Ducassi, Luis Morales, Enrique Montonlieu. ENTERTAINMENT ON SHIPBOARD.-William L. Saunders, Chairman; Mr. and Mrs. S. D. Warriner, Mr. and Mrs. Thomas Robins, Mr. and Mrs. George.D. Barron, Mr. and Mrs. R. B. Watson, W. E. Greene. GENERAL MANAGEMENT. .Joseph Struthers, Chairman; Albert E. Vaughan. There were ten sessions of the Institute held for the presentation and discussion of, technical or professional papers. Eight of these sessions were held on the steamer while en route, and two in the ball-room of the Hotel Tivoli, at Ancon, C. Z. Mr. David W- Brunton, President of the Council, presided at all the sessions, except the sixth, at which Mr. Charles Kirchhoff, past President, occupied the chair. The following list includes the papers presented in oral abstract by the authors: First Session., October 24. The Summit Hill Mine-Fire, by W. A. Lathrop, Philadelphia, Pa. Mine-Fire at the Calumet and Hecla Mine, No. 8 Shaft., by S. D. Warriner, Wilkes-Barre, Pa. Fire in the Big Lick Stope, Lykens Valley and Williamstown Colliery, by R. V. Norris, Wilkes-Barre, Pa. Mine-Fire in the Hecksherville Valley, Schuylkill Field, Pa., by W. J. Richards, Pottsville, Pa.. Fire in the Monarch Mine, near Rock Springs, Wyo., by S. A. Taylor, Pittsburg, Pa.

Dec 1, 1910

By T. H. Eyde

Estimated natural zeolite production worldwide during 2004 remained at about 3.6 Mt (4 million st), about the same as in 2003. China continues to be the largest producer of natural zeolites followed by Cuba, Germany, Japan and South Korea. This may be changing, however. Since 1988, zeolite production from Australia, Indonesia, Malaysia, New Zealand, Philippines and Thailand has increased rapidly. Most of the production is consumed in aqua culture. Global demand for seafood has exceeded the ability of the oceans to supply it without over fishing. Zeolite minerals remove ammonia compounds from the ponds in which fish and shrimp are grown. It is estimated that, in Thailand and Indonesia more than 55,000 farms produce260 kt (286,500 st) of shrimp. Therefore, as shrimp production increases, so does zeolite consumption.

Jan 1, 2005

An understanding of the origin of mineral deposits and their relationship to local and global geotectonics is essential if regional targets for mineral exploration are to be chosen. Volcanism, metamorphism and tectonism are especially significant for the origin and emplacement of mineral deposits, which, far from being fortuitous oddities of nature, occupy well defined positions within distinctive lithofacies. Thus, suggestions for mineral exploration targets can be made taking into consideration the position of &apos;fossil&apos; convergent and divergent plate tectonic boundaries to indicate areas of specific types of mineralisation. To be borne in mind, though, that level of exposure, time and location of magma generation are all additional and important controlling factors. To further understand the importance of the above parameters, one must refer to the concept of paired metamorphic belts (Miyashiro 1973) which develop during an orognic cycle. These belts are generally constructed in such a way that an ophiolite type complex with metamorphic grades related to high pressure and moderate temperature regimes is flanked by an area of calc-alkaline volcanism and granitic activity with metamorphic grades within a region of high temperature and low pressure. The former situation is usually the seat of primary magmatic mineralisation, whereas the latter contains base metal. Deposits of acid plutonic and volcanic association. As will be seen later, this particular metamorphic-volcano-orogenic situation is well developed in some parts of New Zealand. For the present purpose a distribution of potential ores as related to plate tectonic processes is given below:a) Divergent plate boundaries: primary magmatic Ni-Cu, Pt,Cr, PeS2 and Cu, Pb,Zn in hot brines-hydrothermal environments Mn deposits.b) Convergent plate boundaries: stratabound Cu-Fb-Zn-Ag of felsic volcanogenic association. Porphyry eu-Au of island arc type, porphyry Cu-Mo of continental type. Cu, Au, Y, Sn, Hg, Sb of vein type and replacement lode related to granitic activity.c) Au of hydrothermal vein association, related to late dynamo-metamorphic events. By virtue of ocean floor spreading, regions of divergent plate boundaries are eventually juxtaposed or welded n to areas where plate collisions occur. This is then followed by partial melting due to various causes, just above the descending plate; thus creating a zone of acid to intermediate magmatism. The final picture is that of an orogenic zone with the paired metamorphic belts outlined above.

Jan 1, 1976

By William R. Yernberg

The Cripple Creek & Victor Gold Mining Co.(CC&V) celebrated completion of a two-year, $168.5-million expansion and capital improvement program. An open house celebration was held in the historic mining town of Victor, CO on Oct. 4, 2002. Hundreds of townspeople, the press and other invited guests from the mining industry joined the employees of CC&V in the celebration. The event included mine tours, company displays and a barbecue picnic, complete with a country and western band. The Cresson Mine is located about 40 km (25miles) west of Colorado Springs, CO between the towns of Cripple Creek and Victor. The mine is the only large-scale gold mining operation in Colorado and now employs about 300 (ME, October 2001, pp.21-28). The operation is a joint venture between Anglo-Gold (Colorado) (67%), based in Greenwood Village, CO, and Golden Cycle Gold (33%), based in Colorado Springs. CC&V is managed by AngloGold North America. AngloGold North America is the U.S. subsidiary of AngloGold, the world’s second largest gold mining producer. AngloGold is based in Johannesburg, South Africa.

Jan 1, 2002

By K. K. Kelley

The entropy values at 298.1° K. for the elements and inorganic compounds, on which sufficient data were available for calculation in 1931, were discussed in a previous publication (96).3 Since that time the specific beats at low&apos; temperatures of many more inorganic substances have been determined, and considerable advances have been made in the realms of spectroscopy applicable to the determination of thermodynamic properties. Moreover, a critical study of the existing vapor-pressure data made by the author (98) furnishes entropy of vaporization results suitable for obtaining approximate values of the entropies of a number of gases from the entropies of the solids or liquids. Consequently, it appears worth while at the present time to supplement the former publication, giving the new values now obtainable and making such revision in the older values as the data warrant. The methods of calculating entropies were discussed in previous publications (96, 98) and will not be repeated here. ENTROPIES AT 298.1° K. FOR INORGANIC SUBSTANCES In the following pages, the same arrangement is followed as in the previous publication (96). All entropy values are expressed in 15° gram-calories per degree Kelvin per gram-formula mass of substance. The figures given for gases do not include the effect of nuclear spin, as is nearly universally customary at present. The estimates of accuracy in the case of the values obtained from heat-capacity data apply only to the existing measurements and to the necessary extrapolations as they are made. It is assumed usually that the substances are in such an energy condition at the lowest temperatures reached in the specific-heat measurements that the usual normal type of extrapolation may be made. No allowance is made for error in this assumption. The recent work on Gd2SO4. 8H2O and FeC13 illustrates the difficulties that may arise in obtaining the entropies of some paramagnetic substances. Also the data and calculations for such substances as CO, H20, and N20 show that the correct entropy is not obtained in all cases by indiscriminate application of the usual

Jan 1, 1936

By R. S. Dean

"It has long been recognized that the properties of polycrystalline substances are not the same as those of single crystals. These differences are especially marked in metels and metallic minerals, and are of greatest practical importance in metal working and ore treatment. The property changes encountered in passing from a metal single crystal to a poly-crystalline aggregate are the same as are produced by cold-working a metal or by the precipitation of a disperse phase. Hence, we may logically assume that the property changes are all due directly or indirectly to the formation of interfacial area or internal surface. Our problem, then, is to ascertain the physicochemical state of the metal atoms at such internal surface and show how this physicochemical condition accounts for the pronounced changes of mechanical, magnetic, and electrical properties that accompany increased internal surface.GENERAL CONCEPT OF INTERNAL SURFACEIn 1678, Huyghens attempted to explain the double refraction of calcite by postulating that crystals were built from a regular arrangement of ellipsoidal particles. Over 100 years later, Abbé Hauy concluded from his studies of cleavage that crystals might be built from small units, but the units were of the same shape as the entire crystal. This idea, which was prevalent in mineralogical thought before the advent of X-ray spectrometry, was discarded when the great success of Bragg made it appear that the chemical atoms were in reality the elements of structure. In the further development of X-ray technique, however, C. G. Darwin, in England, and P. P. Ewald, in Germany, found it necessary to postulate crystal units con¬taining many atoms. The latter gave the name of mosaic crystals to those so constituted. The individual units are supposed to Possess the ideal atomic arrangements revealed by the X-ray but are not oriented with respect to one another."

May 1, 1938