Search Documents

The deposit was discovered during systematic reconstruction of the geological history of glacial overburden, which averages 6 m in thickness over 80% of Sweden, by geochemical sampling and searching for small grains of eroded bedrock. The gold is mainly concentrated in and around high-grade quartz veins within a broad shear zone, though the correlation coefficient between quartz and gold in samples is not significant. Production from two pits, now connected, in the Central and Eastern orebodies has increased steadily from 1 238 kg Au in 1989 to 2 120 kg in 1994, the highest in Europe. The mine has adapted and improved its mining methods to achieve significant productivity increases and cost reductions. Most of the improvements have been achieved through a better understanding of the controls on mineralisation and of the implications of those controls for selective mining. Geostatistics has played an important role in the quantification of grade variability and gold occurrence. Better blasting and loading techniques have improved selectivity, grade control has been enhanced by a grade-control drilling programme, and significant improvements in mineral processing have been made

Dec 1, 1995

By J Lyall Workman, Peter N. Calder

"Large hole rotary drilling is one of the most common methods of producing blastholes in open pitmining. Large hole drilling generally refers to diameters from 9 to 17 inch (229 to 432 mm), however aconsiderable amount of rotary drilling is done in diameters from. 6% to 9 inch (165 to 229 mm). Thesesmaller diameters are especially prevalent in gold mining and quarrying."

Jan 1, 1996

By Filipe Sathler

O projeto CR298 se iniciou no final do segundo semestre de 2014 quando o Coque Rate (CR) médio era de 351,0 kg/t. A meta definida foi de atingir média mensal de CR de 298 kg/t em dezembro de 2016, permitindo aumento de produção com alta taxa de injeção de carvão PCI, porém, com baixo Fuel Rate, garantindo competitividade de mercado. Sendo assim, foi desenvolvido e divulgado um novo modelo mental de operação, processo, manutenção e gestão, envolvendo toda a área de Redução, Utilidades e Aciaria. Várias premissas técnicas foram estabelecidas com um plano de ação detalhado para garantir estabilidade no processo dos altos fornos de forma a obter este resultado. A meta foi atingida antes mesmo do planejado: CR 291,3 kg/t em Maio de 2016 e em 2016 a média anual foi de 297,0 kg/t, com Fuel Rate de 484,4 kg/t.

Oct 30, 2017

By S. J. Broderick

[One phase of the general program for utilization of coal-mine waste led to the possibility of making a water softener from the material, as the waste matter contained both coal and clay and it is known that both these substances can be so activated as to exhibit distinct base-exchange properties. The carbonaceous]

Jan 1, 1941

By C. M. F. Vieira

In the county of Campos dos Goytacazes, north of the State of Rio de Janeiro, Brazil, there is a large production of red ceramic, mainly perforated bricks. A percentage of these bricks are damaged during the firing processing and become a red ceramic waste. This work investigates a possible solution to this environmental problem through the mixture of fired brick wastes, up to 20 wt.%, with clay bodies to produce red ceramics. Cylindrical pressed bodies were fired at temperatures varying from 500 to 1100ºC. After firing, samples were then tested for linear shrinkage, water absorption and mechanical strength. The results showed that brick waste addition did not changed the workability of the clay and that up to 5 wt.% of waste no detrimental effect occurred on the fired properties at all temperatures.

Jan 1, 2010

By Elizma Ford, Vincent Sithole

"Two shortened test procedures for estimating the Bond ball work index are compared for suitability of use on Zambian/DRC-type copper–cobalt ores. The first procedure is based on a batch milling test while the second procedure is based on a limited locked-cycle test. Both procedures were conducted using a standard Bond test mill. INTRODUCTION The Bond ball work index is widely used in the field of minerals processing as an indicator of ore grindability. The work index is determined by means of a locked-cycle test procedure that typically requires seven to eight cycles to stabilise at a re-circulating load of 250%. A typical test requires between three to four kilogram of ore sample and around eight hours of operator time. For geometallurgical test work applications, where a large number of variability samples are to be tested, it would be highly beneficial to use a test procedure that requires less sample mass and operator time. Certain test work laboratories, for example SGS and JK Tech, are already offering various types of shortened test procedures for estimating the Bond ball work index. This paper discusses a comparison of two shortened test procedures that were evaluated for suitability of use on Zambian/DRC-type copper–cobalt ores. EXPERIMENTAL Test Procedure 1 – Batch Milling The first test procedure is derived from a batch milling approach proposed by the University of Hacettepe (Aksani, 2000). Some modifications were, however, made to the data analysis method from that originally proposed. During this test procedure, a 700 mL volume of sample is milled in a standard Bond test mill for a pre-determined number of revolutions. The feed and product particle size distributions are measured for each test. These results are then used to back-calculate a cumulative breakage rate parameter (k) for each particle size, according to the following formula:"

Jan 1, 2015

By R. E. Jones

"INTRODUCTIONCominco Limited, one of the free world's largest producers of lead and zinc having majority ownership in Pine Point Mines Ltd., operates a mining and concentrating complex on the south shore of Great Slave Lake in the Northwest Territories. The mine was developed in 1963-64 and commenced operation late in 1964 with the direct shipping of high grade ore. The concentrator started production in November 1965 at a design throughput rate of 5,000 T.P.D.In 1968, the Company acquired the mining rights to a large ore body located to the east of the Pine Point claims and subsequently an expansion program at the concentrator raised the throughput rate to 8,000 T.P.D. The expansion included a third grinding circuit and additional flotation capacity. The flotation capacity took the form of a completely separate circuit from the existing flotation plant. In 1972, the zinc flotation circuits were modified to include two additional stages of cleaning. This change concluded the ""Pre-Consolidation Flotation"" circuit at Pine Point.In considering these modernization programs of the flotation section of the concentrator, the philosophy was to utilize the largest available machine having proven and modern technological changes. With the advent of the large capacity machines available in the late 1970's, it was considered a suitable time to revamp the entire flotation circuit at Pine Point in 1979. The Circuit Consolidation Project was developed to meet this requirement."

Jan 1, 1982

The key to the successful debt funding of a new mining project, whether in economically established or developing nations, is the submission of a comprehensive feasibility study. The feasibility study forms the basis from which the resource banker can construct financial models which govern the amount of available funds, the conditions which control the supply of such funds and the time period over which the loan may be repaid. The bank will wish to ensure that the feasibility study is the best representation and confirmation of reality possible because this model is the basis of the loan security package. Thus the study will be vigorously interrogated by independent experts in all its elements including the ore reserve, mineability, metallurgy, operating and capital cost profile, environmental factors and management. A well constructed feasibility study, undertaken by well recognised and respected independent consultants can save the client company a great deal of real and opportunity costs especially in relation to project timing. Once constructed and operating, the mining project may face one or more completion tests in relation to the loans provided. The genetics of such tests often relate to either the ability of the operating company to become solely responsible for the repayment of the loan or to be rewarded by lower interest rates or some other mechanism. Strong professionalism, accessible records, good checking procedures and high quality, competent site management will greatly assist the client company passing these tests. A record of well established technical competence with its bankers may well assist a company in the establishment of a mezzanine loan for the early development of its next project, thus allowing an earlier return of dividends to shareholders.

Jan 1, 1995

Water rights and availability are extremely contentious issues in many mining regions around the world, in some instances leading to violent confrontation. This situation has the potential to only get worse because competition for 'scarce' water resources will increase with population growth. In this environment the dilemma facing the mining industry is how to generate confidence in developing a responsible, sustainable and transparent water management strategy that is recognised as such by all stakeholders. Whilst the water needs of the mining industry are minor compared to those of agriculture, an operating mine requires a relatively large quantity of water on a daily basis to carry out operations. Another contentious aspects of new mine development is the debate between all stakeholders on the amount and quality of water that a mine is able to discharge into the environment should this be required. There are a multitude of water resources available to the mining industry for operational needs however much of this water is saline and over the last two decades there has been a continual decline in water quality (ie salinity has increased). In today's world there are enormous internal and external pressures to reduce water consumption at a mine and/or alternatively use water not considered a resource by the local community (ie sewage, saline or salt water, desalinated water). Strategies to meet these objectives can be achieved by implementing good water management practices, by recycling process water, reducing water losses by evaporation and seepage (ie by increasing and improving dewatering practices) and employing new technologies such as dry stacking and dry processing. Recycled water, acid mine drainage water and water collected in the mining area have the potential to impact mineral processing performance, unless they are treated, because of the build up of mineral salts and decomposed chemical products in these types of waters. Besides this the regulatory requirements of any water discharged from a mine site (quantity and quality) have also become more stringent. For these reasons there is now some form of water treatment practiced at most mining operations around the world. This paper provides an overview of water stewardship undertaken in the mining industry over the last two decades and provides examples of water treatment practices that have recently been installed at mining operations that may be of interest to the reader.

Sep 13, 2010

By Dina M. Aloi

In today?s evolving and globalized world, mining companies are being pressured to move beyond compliance towards long-term sustainability and sustainable development. Companies are expected to ?engage? communities without a clear understanding of ?how? to do this or to what end. This move, away from compliance, develops more of a focus on ?Community? Social Responsibility and sustainability. This shift leads to the development of world-class projects that provide sustainable development for people, reduce the incidence of costly delays, and promote good global citizenship for companies. The process of ?engaging? communities in mining project design and development leads to a stronger license to operate, and a reduction in social and political risk. To create this mutually beneficial relationship between communities and companies, communities must be ?engaged? in the project development and risk assessment processes as early as possible, preferably during the exploration or the concept phases. How to create this ?engagement? and manage this risk will be discussed.

May 1, 2007

By William A. Hustrulid

An overall summary and the individual reports of eight workshops to determine research and development needs in western mining ore presented. Problem areas are identified, and recommendations regarding priorities, funding sources, and prime movers are made. The objective of this contract was to identify research and development needs for advancing mining technology as well as health and safety measures for western U.S. Surface and underground mining. This was accomplished by convening a series of workshops where problems could be thrashed out by producers of trona, uranium, open pit copper, underground salt (from the Midwest and New York), underground metal and nonmetal, etc. In addition to problems, future priorities, funding, and the desicion as to who should be the prime mover on R & D were discussed.

Jan 1, 1976

By Sean Gallagher, William S. Marras, Alan S. Litsky, Velimir Matkovic, Deborah Burr, John Landoll

Study Design. Survival analysis techniques were used to compare the fatigue failure responses of elderly motion segments to a middle-aged sample. Objectives. To compare fatigue life of a middle-aged sample of lumbosacral motion segments to a previously tested elderly cohort. An additional objective was to evaluate the influence of bone mineral content on cycles to failure. Summary of Background Data. A previous investiga¬tion evaluated fatigue failure responses of 36 elderly lumbosacral motion segments (average age, 81 ± 8 years) subjected to spinal loads estimated when lifting a 9-kg load in 3 torso flexion angles (0°, 22.5°, and 45°). Results demonstrated rapid fatigue failure with increased torso flexion; however, a key limitation of this study was the old age of the specimens. Methods. Each lumbosacral spine was dissected into 3 motion segments (L1-L2, L3-L4, and L5-S1). Motion segments within each spine were randomly assigned to a spinal loading condition corresponding to lifting 9 kg in 3 torso flexion angles (0°, 22.5°, or 45°). Motion segments were statically loaded and allowed to creep for 15 minutes, then cyclically loaded at 0.33 Hz. Fatigue life was taken as the number of cycles to failure (10 mm displacement after creep loading). Results. Compared with the older sample of spines, the middle-aged sample exhibited increased fatigue life (cycles to failure) in all the torso flexion conditions. Increased fatigue life of the middle-aged specimens was associated with the increased bone mineral content (BMC) in younger motion segments (mean ± SD, 30.7 11.1 g per motion segment vs. 27.8 ± 9.4 g). Increasing bone mineral content had a protective influence with each additional gram increasing survival times by approximately 12%. Conclusion. Younger motion segments survive considerably longer when exposed to similar spine loading conditions that simulate repetitive lifting in neutral and flexed torso postures, primarily associated with the increased bone mineral content possessed by younger motion segments. Cycles to failure of young specimens at 22.5° flexion were similar to that of older specimens at 0° flexion, and survivorship of young specimens at 45° flexion was similar to the older cohort at 22.5°. Key words: biomechanics, low back disorders, fatigue failure, age, motion segments, vertebral endplate fractures, torso flexion, lifting, bone mass. Low back disorders (LBDs) are a major cause of both short- and long-term occupational disability in the United States, and it is clear that workers in certain occupations are more susceptible to LBD.2-5 Specifically, epidemiologic studies have shown that jobs involving heavy physical demands such as construction,2,3 mining,2,4 and farming,5 engender increased risk of back pain. These occupations are thought to experience high LBD rates as a result of their extreme postural and manual lifting demands. Studies have shown that jobs involving significant lifting 6-9 and jobs that involve frequent bending10-12 are associated with increased LBD risk. Workers in the mining industry, in particular, often have to lift heavy materials in restricted workspaces that compel torso flexion. An understanding of the impact of repeated loading of the spine in flexion on fatigue failure of spinal tissues is thus a critical issue for our research agency, which is concerned with reducing the pain and disability associated with LBD in the mining industry. It is well accepted that loads experienced by the spine during manual lifting tasks are sufficient to cause fractures in the endplates of lumbar vertebrae, particularly on repeated loading. 13-15 Endplate fractures may not be painful in and of themselves 16; however, evidence suggests that the process of internal disc disruption and disc degeneration may be initiated via endplate fractures. 16,17 It has been shown that endplate damage will alter the distribution of stress in the disc, resulting in buckling of the lamellas of the internal anulus.17 Once this process has been initiated, repeated spine loading will cause additional disruption of the anular fibers, resulting in formation of significant fissures or tears. 11-21 If these tears occur near or extend close to the outer portions of the anulus, a wound healing process is initiated, which involves infiltration of mast cells, macrophages, and re¬lease of cytokines and growth factors. 21 The presence of these infiltrates has been strongly linked to discogenic low back pain. 21,22 Indeed, for patients experiencing chronic low back pain, the prevalence of internal disc disruption is at least 39%,19 which represents the most

By W. H. Somerton

The basic objective of this project was to determine the permeability of coal fracture systems as a function of effective stress. The detailed steps in accomplishing this objective are given in Article I of the contract under which the work was conducted as follows: Sec. 1.1 The objective shall be to determine the permeability of the coal fracture system as a function of effective stress. At least three bituminous coals shall be studied and at least five samples of each coal shall be tested. The sample size shall be as large as possible to be representative of coal found in the seam; a minimum of four inches is preferred.

Jan 1, 1974

By R. V. Ramani

This volume is the first of a four-volume final report on research carried out under a contract from the U.S. Bureau of Mines on the development of a computer simulation model for surface mine reclamation planning. The other volumes are titled as follows: Volume II: Dragline Model, Volume III: Mine Coordinate Generator System, and Volume IV: User's Manual for OPMHS/2. This report deals with the development of a geological model for surface mine planning. The most common orebody modeling techniques are described. A brief review of geostatistical theory and concepts is presented. A geostatistical option for orebody modeling is developed and validated. Computer programs and sample outputs are appended.

Jan 1, 1985

By Helvio Pessanha Guimarães Santafé Jr.

The coir fiber extracted from the husk of the coconut has been extensively used as polymer composite reinforcement in a variety of industrial applications ranging from civil construction to automobile seat cushions. The hydrophilic coir fiber does not act as an effective reinforcement owing to its low interfacial strength with hydrophobic polymers. As a consequence, coir fiber composites display relatively low mechanical strength. The objective of this work was to investigate the effect of an acetylation treatment of the coir fiber surface on the mechanical behavior of epoxy composites with amounts of fibers up to 30% in volume. Coir fibers were immersed in an acid solution of acetic anhydride for one hour, washed and dried, before mixing with DGEBA/TETA epoxy to fabricate the composites. Flexural mechanical properties were obtained by bend tests. The results showed significant differences to similar composites with alkali treated coir fibers that have been previously investigated.

Jan 1, 2010

By D. Dimitriadis, T. Polglase, W. Phillips, R. Jenny, M. Botz

Cyanidation processes for the extraction of gold or silver frequently involve the processing of sulfur-containing solids which react with cyanide to form thiocyanate. The formation of thiocyanate is an undesired side-reaction, and in many cases thiocyanate formation results in a prohibitively high cyanide consumption. With the increasing number of gold and silver mining projects which involve the processing of sulfide ores or concentrates or which utilize a biological sulfur oxidation process, more attention has been focused on minimizing thiocyanate formation and in treating solutions to eliminate toxicity associated with thiocyanate. Though not yet commercially applied, there are several technologies available to recover cyanide from thiocyanate to both reduce tailings toxicity and allow the reuse of cyanide otherwise lost to thiocyanate formation. This paper presents an overview of technologies available for recovering cyanide from thiocyanate along with estimated operating costs for the technologies. Pilot testing data suggests that in some cases, cyanide can be recovered from thiocyanate for approximately the same cost as newly purchased cyanide.

Jan 1, 2000

By Richard L. Fowler

[Study and development of sensing techniques and sensors were performed to aid shuttle car drivers in detecting, obstacles and in guiding the car along the face haulage route. Microwave, acoustic, and optical sensing techniques were considered as part of the feasibility study for obstacle detection. Various guidance techniques, including wire-following and rib-ranging were investigated. Active optical sensing was selected for obstacle detection to obtain the bear overage and sharp angular cutoff characteristics required within the packaging limitations defined by the shuttle car configuration. Rib-ranging guidance was selected to achieve completely self-contained shuttle car system which responds to the mine geometry without need for wires, stripes, or other path defining devices. Extensive hybrid computer simulation runs were performed to valuate various guidance techniques during the feasibility study. Subsequent simulation rues were performed to establish parameter values for the rib-ranging guidance system. The obstacle detection and guidance system was designed, fabricated and installed on a standard shuttle car. The system satisfied all applicable permissibility requirements of Schedule 2G. An experimental permit was issued to Bendix for operation in an underground coal mine. System evaluation tests were performed first above ground at the Bendix Research Laboratories. The simulation model was validated by these runs. Final testing wan performed underground in an operating mine with an experienced shuttle car driver. All sensors successfully demonstrated Chi predicted performance capability during underground face haulage tests. Dust did not Impair system performance and lens cleaning was not required during working shifts. Further development is required to achieve the desired obstacle detection performance Closed loop steering control with manual override is recommended o: mended for the lateral guidance e system. The guidance system should be an invaluable aid to low-coal shuttle car drivers where continuous mining machines are utilized.]

Jan 1, 1973

By Everaldo Afonso Fernandes

O estudo do efeito do elemento de liga Zircônio, nos teores 0,15% e 0,22%, sobre a liga AL-0,05%Cu-[0,35-0,45]%Fe foi realizado com a finalidade de caracterizar o desempenho em cabos e fios para fins de transmissão e distribuição de energia elétrica. Dessa forma, foi adotada sequencia operacional a fim de caracterizar as estruturas apresentadas pelas ligas. O processo de solidificação foi realizado de modo unidirecional horizontal. Posteriormente os lingotes passaram pelos processos mecânicos de usinagem e laminação para obtenção de corpos de prova com quatro distintos diâmetros (2,7; 3,0; 3,8; 4,0) mm a fim de se ter amostras próximas das bitolas utilizadas nas indústrias de cabos elétricos. Todas as ligas foram caracterizadas termicamente [Análise Térmica], eletromecanicamente por meio do ensaio de tração [LRT] e condutividade elétrica [%IACS].

Aug 8, 2018

By James P. Rider

Significant advances in longwall mining technology and equipment have occurred over the last decade. By the late 1990s, longwall mine output accounted for 40 percent of all underground output in the U.S., and today longwall mines account for approximately 50 percent of coal produced underground in the United States. A 53 percent increase in average shift production rates has occurred over the last fifteen years. This increased longwall productivity has meant that far more dust is being produced and controlling respirable coal dust provides an ongoing challenge for coal mine operators. The National Institute for Occupational Safety and Health (NIOSH) has completed a series of benchmark surveys at longwall operations across the country to identify current operating practices and the types of controls being used. Gravimetric and instantaneous dust sampling was completed to quantify dust generation from major sources on the longwall section and to determine the relative effectiveness of the different control technologies in use today. Substantial reductions in dust levels were realized at sampling locations on the face when compared longwall surveys conduct in the 1990?s. This paper summarizes the results from the underground dust surveys and discusses current longwall dust control technology and operating practices.

Jan 1, 2010

By J. H. Archibald

"IntroductionShot-saws are used for sawing rock throughout the dimension stone industry especially in granite quarry mills. Shot-saws, as currently designed, have an inherent wear problem which leads to slow cutting rates and repetitive blade changes which consumes much time. Because the saw blades are made from steel the abrasive shot used with them is limited to a certain hardness which effects the over-all efficiency of the sawing operation. Suggestions are made toward optimization of blade design and the sawing process. Blade DesignA common steel blade design is shown in Figure I. Note the perforations in the blade. These perforations or holes in the blade serve two or three purposes. The most obvious reason is to allow the abrasive shot a pocket in which to collect at the bottom of the blade, so that it can be distributed from these pockets into the cutting zone underneath the blade. The abrasive is fed to the saw in a slurry and usually comes in from the top. The blade must then cut a kerf wider than itself in order that the abrasive grains have a path leading from the top of the blade, down along its sides, and finally reaching the pockets and cutting zones. This circuitous path followed by the abrasive leads to side wear on the blades and high friction which can lead to blade buckling in severe cases. However, the fluidized path of the abrasives down the sides of the blade serves another purpose which is a positive gain if conditions are properly controlled. The abrasive slurry interacts with the perforations of the blade, the blade itself and the rock. This gap and the perforations in the blade, which are fluid filled, are sites of constant shearing motion. Eddy currents form in these gaps and pockets which tend to stabilize the blade by setting up balanced hydrodynamic forces which otherwise might not form in a non-perforated blade. A stable blade produces a more uniform cut in the rock. The third and final reason for the perforations are to allow the blade to wear in such a fashion that new pockets are always being formed and, consequently, new cutting surfaces between these pockets are also formed."

Jan 1, 1993