Search Documents

By Paul A. Roy

The North Shore Connector Project for the Port Authority of Allegheny County constructs twin Tunnel Boring Machine (TBM) tunnels through cohesive soils and rock beneath the Allegheny River and a narrow city street in Pittsburgh, PA. The tunnel alignment includes an historic building on shallow foundations, modern buildings on deep foundations, and an office building constructed directly over the alignment during the design of the tunnel sections. This paper provides an overview and update of the general site conditions, TBM tunnel design, and support of excavation for the TBM launching pit. Deformation limits, ground improvement, monitoring and mitigation plans are also discussed.

Jan 1, 2008

By S. Holtermann

Through the process of Riverbank Filtration (RBF), the Louisville Water Company plans to obtain a higher quality source of water for their B.E. Payne Water Treatment Plant (WTP) by means of four collector wells located in the alluvial aquifer along the bank of the Ohio River. The collector wells are connected to a 2,850 L/s (65 mgd) pumping station by a 2,362 m (7,750 ft) long, 3 m (10 ft) finished diameter tunnel located in limestone and shale bedrock, which is approximately 45 m (150 ft) below the surface. High tunnel boring machine (TBM) production rates were achieved in this moderately weak bedrock; most of the tunnel only required support in the crown. An unanticipated water-bearing fault and unanticipated ground behavior proved challenging and required quick thinking to minimize impacts to construction. Tunneling conditions are discussed in detail, together with the methods used for overcoming the groundwater and ground behavior challenges. The tunnel is expected to be completed in April 2009.

By Xueyuan Nie, Xuezhi Zhang, Henry Hu, Shen Xinwei, Jimi Tjong, Li Fang

With the demand for weight reduction in vehicles and airplanes, researchers have shown great interested in casting wrought aluminum alloy 7075 because of its potential advantages such as high strength-to-density ratio and stress-reduction capabilities. It is therefore essential to conduct a fundamental investigation on solidification behavior and grain microstructure of alloy 7075. In this study, a commercially-available wrought aluminum alloy 7075 was used to study the solidification behavior of alloy 7075. A thermal analysis was performed based on the cooling curve and its corresponding first and second derivative curves. The nucleation of the primary a-Al phase and eutectic phases were analyzed. The comparison between the microstructures of the wrought and cast 7075 alloys shows that coarse microstructure and porosity are present in the cast alloy. The techniques for grain refinement in casting, such as the addition of the nucleating particles and applied pressure, should be employed to reduce the dendrite arm spacing and the porosity.

Jan 1, 2015

By D. S. Saxena, Jack K. Tuttle

Lack of understanding of useful applications of explosives on construction work stem primarily from the fact that explosion is commonly associated with destruction. On rock excavation and other construction works a certain quantity of explosive is harnessed to perform useful work at the source e.g. blasts to disintegrate rock. Development in rock blasting techniques, including the use of multiple-row blasting with short delay ignition, have made it impossible to excavate rocks close to or below buildings even in closely built-up areas. To permit the use of explosives on construction projects, in ways that will not damage existing structures, guidelines have been developed from careful measurements of intensity of ground vibrations. Accurate electronic instruments are now available for doing this. PLANNING AND CONTROL Blasting operations must be carefully planned and carried out to avoid discomfort to persons or damage to property. This increase in the use of rock blasting in city areas alone has led to a number of problems due to ground vibrations, air shock waves, and the psychological effect of noise. While the latter seldom if ever causes damage, it does create irritation and discomfort to persons living or working near the blasting sites. A result of this is a steady increase in the number of complaints in respect of damage to houses and other premises. Many such complaints are genuine and damage may undoubtedly be caused when incorrect blasting techniques are used.

Jan 1, 1997

By Robert C. Steckley

A study of joints in Marathon County, Wis., was made to determine the orientation of regional paleotectonic stresses and to develop a method of using optical diffraction analysis (ODA) in studying joint orientations and spacings. Standard geologic and petrofabric techniques employing the use of a geologic compass and a Schmidt net were used in gathering, describing, and reducing joint orientation data. Analysis of selected outcrops with ODA indicates that ODA can be applied to study both joint orientations and spacings. ODA is shown to be a rapid method that can be used to complement standard petrofabric techniques, especially in the study of joint spacings.

Jan 1, 1972

By James G. McKelvey

Owners have seen several major tunnel projects in recent years fall victim to a general reduction in the number of bidders as well as an erratic range of pricing. It should be noted though that this is not a universal trend and some projects have seen good competitive bids. Contractual terms and conditions are an important factor in attracting good competition. The Front End documents of tunnel projects have come under increasing scrutiny as tunneling contractors in the U.S. industry are looking much more closely at their risk exposure in the contract terms and conditions. Considering the amount of tunnel construction work upcoming in North America, it is important that General and Special Conditions are put together in a way that provides a reasonable basis to execute the Contract and also provide a fair, balanced and swift way to resolve disputes.

Jan 1, 2008

By Gisele Ferreira de Lima

Magnésio e suas ligas são promissores para armazenagem de hidrogênio devido à alta eficiência, boa reversibilidade, baixo custo e segurança. Entretanto, hidretos à base de Mg apresentam cinéticas de ab/dessorção lentas, temperaturas de operação muito altas, e alta reatividade ao ar para aplicação práticas. A moagem de alta energia (HEBM) combinada com o uso de catalisadores têm produzido nanocompósitos à base de Mg com cinéticas mais rápidas. Recentemente, processos termomecânicos e de deformação plástica severa (SPD) têm sido investigados para produzir nanocompósitos em volume com melhor resistência ao ar (processo de ativação) e que podem ser facilmente fabricados em escala industrial. No presente trabalho, amostras 2Mg-Fe foram misturadas com CNT (0-5%p.) por HEBM, e em seguida processadas por extrusão a quente (termomecânico) a 300oC e/ou laminação a frio (SPD) a temperatura ambiente. Pós com 0%p a 5%p. de CNT mostraram padrões de DRX muito similares indicando similares nanoestruturas. Todas as amostras puderam ser laminadas, mas somente amostras com menos que 2,0%p. de CNT puderam ser extrudadas, e submetidas pela combinação de extrusão-laminação. As propriedades cinéticas, medidas pelos métodos Sieverts e DSC, foram piores para as extrudadas, intermediárias para as extrudadas/laminadas e melhores para as somente laminadas. Nessas últimas, os picos de Bragg mostraram baixa intensidade e textura favorável ao longo de (002) no Mg, que possivelmente explicam esses resultados. Quanto maiores foram as quantidades de CNT melhores foram as propriedades (cinética e temperatura de dessorção).

Aug 8, 2018

By Behrouz Tehrani

The size, complex issues, and requirements to construct large number of tunnels, for a single project, expeditiously, and without exceeding the overall project budget, a program Construction Management (CM) team is highly recommended to be selected early during design process to provide guidance/direction relative to contract packaging and scheduling. This paper is not focused on the project itself, however, the emphasis is on experiences gained from the project. Wishing that some of the strategies described in this paper will be of value to owners of underground project.

Jan 1, 2008

By H. B. Humphrey

[EXPLOSION of gas and dust in coal mines, have caused death t lid injure to mines, and destruction of workings in all countries where coal is mined underground. In the United Stales the first reported explosion wits in Min; explosions have continued to the present. The danger to film ill it mine When an explosion occurs in not always measured by the violence created or by their nevi lies, to the area through which flame and Violence extend. As many, perhaps more, risen have died from gases and lade of oxygen (known as "after-damp") than have been killed by the blast and hart. Me explosions often are caused by it combination of factors, including concentration of methane in air, formation of clouds of dust, and the presence of a flame or spark. These explosion factors have varied with changes ill milting method and practises over the years, but the basis causes have always been the salve. Understanding of the causes and to acceptance of ways to guard against explosions and their effects have been slow to spread from investigates to officials and Own to bosses and miners. To a considerable extent there hats lawn a belief that explosions were a joining risk but might hr, put oil hut could not be presented. Such belief is based on the human failure to maintain and observe necessary precautions. These failures, caused by inertia to change, carelessness, or reliance on continuance, of past explosion-free years, are being reduced in number and effect by education of miners and supervisors and acceptance of higher prevention standards.]

Jan 1, 1959

The development of a noise attenuated compressed air driven fan is described. The fan, which employs the jet reaction principle, possesses blade extension pieces which penetrate into an acoustically treated annular chamber. The dominant noise source, namely the air jets, is thereby partially suppressed. In addition, the increased moment arm of the jets leads to an improved propulsion effect which contributes to the improved aerodynamic performance of the unit.A typical measure of the improvement of this type of auxiliary mine ventilation unit is a 4 per cent increase in efficiency and a 10 dB (A) drop in sound level for a fan duty of 0·5 kPa and 1600 litre/s. This degree ofattenuation corresponds to at least halving the loudness level, a subjective noise measure.

Jan 1, 1973

By Jason Clarke, André R. Laplante

"The gravity-recoverable gold (GRG) ore characterization test was developed 15 years ago and has been applied to hundreds of ore samples. The test accurately determines the size distribution of GRG, at which grind it is recoverable, and the extent of its liberation above 150 µm. This contribution shows how the test can be simplified, what are the likely problems to occur, and what information is then lost. Two simplified versions of the test are presented, of which the simplest, grinding a 20-kg sample to a P80 of 75 µm, is retained as the best one. A database of 18 comparative tests is presented. The choice of the full GRG test vs. the simple test is discussed, as is the deportment of the GRG recovered in the standard test but not in the simplest test.INTRODUCTIONThe GRG test was developed in 1990 to characterize the progressive liberation of gold in representative samples of ores, with the primary objective of generating data for a gold gravity recovery model (Woodcock and Laplante, 1993; Laplante et al., 2000). Characterization includes the size distribution of GRG as well as the grind size at which it becomes recoverable. This is achieved in a 3-stage protocol of liberation and recovery using a laboratory centrifuge unit, a Laboratory Knelson Concentrator 3 inches in diameter (KC MD3). This protocol is shown in Figure 1. The first stage takes place at a F100 of 850 ?m (F80 of ~550 ?m), the second at F80 of 180 ?m, and the third at a P80 of 75 ?m. The rationale for the three cycles is the desire to preserve the original size distribution of the gold grains in the ore and to obtain a recovery grind size curve. The feed is a representative sample of ore that can be extracted from ore samples (e.g. drill core reject) or stream products of the grinding circuit other than circulating loads or product having undergone hydraulic classification (e.g. rod mill discharge or SAG screen undersize). Ideally the samples should weigh between 60 and 100 kg, depending on feed grade and gold top size. It is beyond the scope of this paper to fully discuss measures of representativity in the ore sample, for example Gy’s minimum sample mass model (Gy, 1979). However, further work in this regard may be an opportunity. The large initial weight facilitates representativity and minimizes weight and sulphide recovery to the concentrate (since concentrate weight is relatively constant at ~100 g), which limits the recovery of gold in nonsulphide gangue or gold carriers (i.e. sulphides). Thus, the 100 g concentrate carries principally discrete gold species, such as electrum, and native gold. The concentrate and a 600-g representative sample of gangue of each stage are screened down to 20 ?m and each size class is fire assayed (the concentrates to extinction, the tails up to 30 g per size class). The five coarsest size fractions of stage-1 concentrate are individually upgraded using a hydrosizer and the concentrates examined with an optical microscope to assess the degree of liberation of the gold phase. Scanning electron microscope work has established that the GRG has an excellent degree of liberation below 150 ?m in stage 1 and generally a good degree of liberation in stages 2 and 3 (Guerney et al., 2003); as a result the size distribution of the GRG has been found to approach closely that of gold grains (Nesset et al. 2005)."

Jan 1, 2006

By Robert W. Yokom

As the search for new sources of energy and minerals leads to more remote areas of the country - and the world - the need to plan for adequate housing and community facilities for the construction and operations workforces and their families takes on an importance equal to the mining and processing facilities themselves. A corollary to the need for planning is the increasingly crucial need for development companies to devise effective strategies for dealing with the local communities impacted by these projects. Experience has amply demonstrated the high price to be paid for failure to learn this lesson, a price measured in lost productivity, confrontation with local communities, labor turnover, mental health and other social and eocnomic problems. In Sweetwater, Wyoming, a new industrial activity caused the population to double from 18,000 to 36,000 between 1970 and 1974. During that period industrial productivity fell 25 to 40 percent, cost overruns on the principal new industrial facility exceeded 33 percent, annual employee turnover rates climbed above 100 percent, the local mental health clinic workload increased nine times and complaints to the local law enforcement agency increased 60 percent.

Jan 1, 1981

By Jean-Pierre Hamelin

Ground movements induced by underground excavation are always of critical concern, particularly in urban areas. Compensation grouting now appears as a safe means to control these movements. The paper presents new advanced systems developed by the specialist contractor to bring, at all stages of the project, an efficient control of operations and presents a case history taken from the project at Tren Urbano, Rio Piedras Section, constructed beneath an historic commercial section of San Juan de Puerto Rico.

Jan 1, 2000

By Robert Hopler

In accordance with the 57th section of the Explosives Act, 1875, the following report on the working of the Act during the year ending December 31, 1903, is submitted. There have been no modifications of the law during the year. No complaint is made of any falling off in the general condition of factories and magazines, and in one instance only during the year have legal proceedings been taken for any irregularity. The occupiers of factories and magazines have invariably shown perfect readiness to remedy any defects, and the managers have themselves in many instances introduced improvements tending towards greater safety. The number of deaths (5) from accidents by fire or explosion in the manufacture of explosives is below the average for the decade (6•4). Looking to the large number of persons employed in this trade, the number of deaths is not excessive and will compare favorably with the death-rate in other dangerous trades. Notwithstanding the large increase in the manufacture of explosives, the average number of deaths has greatly decreased since the passing of the Explosives Act, whereas the number of fatal accidents with explosives under conditions to which the Act does not apply appears to increase with the extension of trade.

Jan 1, 2006

By W. H. Strickland, R. H. King

Ultrasonic ranging sensors are inexpensive, have no moving parts, have no lenses to clean, are normally small and unobtrusive, and can measure distances through moderate amounts of dust, smoke, and humidity, so they are well suited to underground mines. In the work reported here, conducted by the U.S. Bureau of Mines, researchers tested ultrasonic ranging sensors for their abiity to define rib line features for computer-aided navigation of underground mine mobile equipment. The investigation began with laboratory tests of field of view, angle of incidence, intersensor variation, and ranging accuracy of the individual rangers in a ring array produced by Denning Robotics of Wilmington, MA. The results showed that the sensors have good accuracy and low variability. Additional experiments at AMAX's Henderson Mine showed the sensors could accurately and reliably measure the distance to mine features, including convex and concave corners and rib intersections. The results showed that when used properly, the ranger data are accurate enough for reliable mine vehicle navigation When used incorrectly, ultrasonic rangers do not provide the anticipated data. Therefore, this report explains the principles of ultrasonic range measurement, describes the ranger's strengths and weaknesses, and explains proper ranger use and data analysis.

Jan 1, 1993

By Y. -H. Chang, Y. -J. Jou, T. -S. Ueng, I. -H. Peng

In order to systematically study the size effect on the shear strength of rock joints, this study used the computer-aided-manufacturing system to reproduce the artificial rock joints for saw-toothed joints, Barton's standard joint profiles of JRC = 4~6 and 18~20, and natural rock joint profiles. We divided, enlarged, reduced, and assembled these joint profiles to obtain joint specimens of various sizes ranging from 75 mm to 300 mm in length. The shear strengths of these joint specimens were tested under different normal stresses using a direct shear test apparatus. The surface conditions of the joints at failure were also examined. The size and geometry effects on the shear strengths of these joints of various sizes and configurations were evaluated based on the test results. Um die künstlichen Trennflächen für reguläre dreieckige Trennflächen, Bartonsche standardmäßige Querschnitte der Trennflächen von JRC = 4~6 und 18~20 und natürliche Querschnitte von Trennflächen wiederherzustellen, benutzt diese Forschungsarbeit das Computergestützte-Erstellungssystem, damit die Maßstabswirkung auf die Scherfestigkeit von Trennflächen systematisch untersucht werden kann. Die Querschnitte werden geteilt, vergrößert, verkleinert und zusammengesetzt, um Trennflächenproben in Längen variierend von 75 mm bis 300 mm zu erhalten. Die Scherfestigkeit dieser Trennflächenproben wird unter unterschiedlichen Normalspannungen mit einem Direktscherversuchsgerät getestet. Die Querschnittszustände der Trennflächen bei Versagen werden ebenfalls untersucht. Nach den Untersuchungsergebnissen werden die Maßstabs- und Geometriewirkung auf die Scherfestigkeit dieser Trennflächen verschiedener Größen und Konfigurationen ausgewertet. Pour étudier systématiquement l’effet de la dimension des fractures des roches sur leur résistance au cisaillement un système de creation de fractures artificielles à l’ordinateur a été employé. Des fractures artificielles triangulaires, profils de fractures de Barton avec JRC = 4~6 et 18~20, et profils de fractures naturelles ont été reproduits. Les profils des fractures ont été arrangés de manière à obtenir des échantillons de longueur entre 75 et 300 mm. Une boîte de cisaillement a été utilisée pour étudier la résistance des fractures au cisaillement, sous plusieurs conditions de contraintes normales. Les conditions superficielles des fractures après rupture ont été étudiées. Les résultats de ces essais, effectués sur plusieurs échantillons de dimensions et configurations variées, ont contribué à établir l’influence des dimensions et de la géométrie des fractures sur leur résistance au cisaillement.

Jan 1, 2003

By John Reilly

The author?s paper at RETC 2007, ?Alternative Contracting Methods? addressed strengths and weaknesses of DBB+DB and introduced Construction Manager/General Contractor (Portland model) and Alliancing (Australian model). Considerable interest in these was expressed by several public agencies at that Conference and at the presentation. The author is assisting the Washington State Department of Transportation (WSDOT) and the Toronto Waterfront Revitalization Corporation (TWRC) with possible implementation of Alliancing. WSDOT is evaluating ways to do this and is considering a delivery methodology, under existing Legislation, based on the CMGC Portland model with incentives and disincentives, moving towards Alliancing. This paper will build on the 2007 paper and update implementation considerations.

Jan 1, 2008

By S. E. Olsen, M. Tangstad, G. Tranell, K. Berg, S. Gaal

In this study, the reduction behaviours of MnO and SiO2containing slags by solid carbonaceous materials was investigated in both small and larger-scale laboratory experiments. Five types of carbonaceous material were investigated: 2 graphites, industrial coke, anthracite and eucalyptus charcoal. The effects of the reductant type/properties on the reduction kinetics, metal composition and metal yield, have been quantified. Results show that the reduction rate is highly dependant on the type of carbon used. It was found that the reductant type significantly influenced the SiO2reduction while it did not seem to have a large effect on the MnO reduction. This may be due to the different CO2and SiO reactivities of the materials.

Jan 1, 2004

NIM reports Report No. 1615 Fluorspar pellets. A survey of the world market and an assessment of future South African production. Report No. 1621 Correction for matrix effects in the analysis of solutions by X-ray-fiuorescence spectrometry. Notices Questionnaire on Technicians The Department of National Education's committee of enquiry into the education, training, utilization, and status of engineering technicians in the Republic of South Africa was established as a result of Resolution 6.3 taken at the Sixth Conference on Engineering Education: The Education and Training of Engineering Technicians. Vraelys oor Tegnici Die Departement van Nasionale Opvoeding se komitee wat ondersoek instel na die opleiding, gebruik en status van ingenieurstegnici in die Republiek van Suid-Afrika is gestig as gevolg van Besluit 6.3 wat geneem is tydens die Sesde Konferensie oor Ingenieursopleiding: Die Opleiding van Ingenieurstegnici. Competition for Student Members of the South African Institute of Mining and Metallurgy Each year the Institute offers a prize (or prizes should the entries warrant it) of up to R100 for the best paper or dissertation on a topic appropriate to the interests of the Institute. The competition is open to all Student Members of the Institute.

Jan 8, 1974

By Gerald T. Homce, James C. Cawley

Arc flash generally refers to the dangerous exposure to thermal energy released by an arcing fault on an electrical power system, and in recent years, arc flash hazards have become a prominent safety issue in many industries. This problem however, has not been effectively addressed in the mining industry. MSHA data for the period 1990 through 2001 attributes 836 injuries to “non-contact electric arc burns”, making it the most common cause of electrical injury in mining. This paper presents results from several elements of a recent NIOSH study of arc flash hazards in mining, and provides information and recommendations that can help reduce these injuries. Characteristics of past arc flash injuries in mining are first outlined, such as the electrical components and work activities involved (based on MSHA data). This is followed by a review of important concepts and terminology needed to understand this hazard. Next, methods for identifying, measuring, and managing arc flash hazards on a power system are covered, with emphasis on recommendations found in NFPA 70E, Standard for Electrical Safety in the Workplace. Finally, results are presented from a detailed arc flash hazard analysis performed on a sample mine electrical power system using IEEE 1584-2004a, focusing on components and locations presenting severe hazards as well as engineering solutions for reducing the risk to personnel. Index terms – electrical arcing, electrical burns, mining, arc flash hazard analysis