Search Documents

By Ali Kahriman, Abdulkadir Karadogan, Umit Ozer, Mehmet Aksoy, Kagan Ozdemir, Adiguzel Deniz

This paper presents the results of ground vibration measurements induced by blasting during the construction of the Istanbul Kadiköy-Kartal metro tunnel which has been driven at a depth of approximately 20-40 m deep under a highly urbanized region of Istanbul city in Turkey. This tunnel is being constructed by a joint venture group. The formation encountered during the construction is classified as hard and strong rock by laboratory and field tests performed by the joint venture group. Within the scope of the study, for the prediction of the peak particle velocity and to determine the slope of the attenuation curves together with the maximum charge per delay for the S4 shaft tunnels and S12 shaft tunnels of this tunnel route, ground vibration components were measured carefully by using four vibration monitors (Instantel Minimate Plus model) during the advancement of the tunnels which required blasting. The particle velocities and frequency values of all blast events are evaluated according to the United States Bureau of Mines (USBM) and German DIN 4150 Norms in order to predict, and compare the influence grades to the neighbouring buildings, and structures. Also, data pairs of scaled distance and peak particle velocity obtained from 114 records at S4 shaft tunnels and 79 records at S12 shaft tunnels were analysed statistically. Empirical relationships with correlation at the 95 % confidence interval were established for different rock units (diabase and arkose) and suggested for the test sites in order to estimate particle velocity of the ground vibrations.

Jan 1, 2007

By W. L. Dare

Tri-axial strains in pillars, created by pillar robbing, were measured in an experiment at the Dysart No. 1 uranium mine near Grants) New Mexico. At this mine, room-and-pillar stoping is used on the advance, and pillars are recovered on the retreat. The are deposit is, for all practical purposes, horizontal. Measuring devices were installed in pillars approximately 90 to 200 feet from the break line, and strains were recorded over a 4-to 6-week period. The measurements indicate that, in general, the algebraic magnitude of vertical strains increased, and the horizontal strains decreased, in turn, indicating that vertical (or near vertical) loads on the instrumented pillars lessened as pillars were recovered.

Jan 1, 1962

By E. A. G. Colls

PART I.-GASES IN INDUSTRY INTRODUCTION THE part played by gases in industry can be considered from at least four distinct viewpoints, viz: (1) As air to support combustion and life and do various kinds of work (2) As fuel, or as essential to certain chemical processes (3) As sources of danger from explosion or fire ( 4) As hazards to man's health The present paper deals with gases only insofar as they are sources of danger, or are hazards to health. It may be noted, however, that, in point of tonnage, air is one of the most important materials handled in any industrial plant. In the operations of the Consolidated Mining and Smelting Company, for example, 138,000 tons of air are handled daily, the only material exceeding this figure being water. The United States Bureau of Mines has listed no fewer than seventy-four gases and vapours that, under certain conditions, may be considered as ex-plosive or dangerous (poisonous). The commonest and most important of these are as follows : Carbon monoxide Methane Acetylene Hydrogen Oxygen Hydrogen sulphide Benzol vapour Ammonia Petroleum vapour Carbon disulphide Hydrochloric acid gas Cyanogen Carbon oxysulphide Chlorine ` Fluorine (and fluorides) Acetone vapour Acetic acid vapour Water gas Natural gas Gasoline vapour Coal gas Producer gas Ether vapour Nitrogen oxides

Jan 1, 1940

By Nathan Feldstein

The wetting of coal dust by aqueous solutions of surface active agents (surfactants) has been studied. Selected for study were thirty coals and typical surfactants selected from the typical classes of anionic, non ionic and cationics. Of these three classes the practical use of cationics in aqueous solutions has been eliminated due to the inherent negative Zeta potential charge of the representative coals studied. The wetting of the coals has been examined by column flow, contact angle, and settling rate measurements. Results indicated that both anionic and nonionic surfactants are to be considered viable for use; low critical micelle concentration values are also preferred for the surfactants. Study of native waters showed substantial variation in properties, i.e., pH, calcium ion concentration, and conductance. pH variations were also noted to affect the effectiveness of selected surfactants. Combinations of nonionic and anionic surfactants have, in certain instances, produced synergistic enhancement in the coal wetting superior to the effectiveness of each surfactant alone.

Jan 1, 1981

By D. I. Smith

Constructing tunnels in congested urban areas requires tunnels to be placed closer together and with less cover than was previously necessary. Contract CQ031 of New York?s East Side Access project will construct four six-meter diameter bored tunnels in a three-up one-down ?T? configuration, with less than three meters of soil between the tunnels. Mixed-face rock and glacial till conditions with a high ground water table will be encountered under active railroad yards. The tunnels will also pass beneath the busiest railroad interlocking in North America with cover as shallow as three meters. This paper discusses the challenges of designing segmentally lined tunnels for these conditions.

Jan 1, 2008

By Eric Konigsmann

"Omai Gold Mines is a large scale open pit gold mining operation located in central Guyana, South America with a 12,000 tonne per day milling facility. Mill operations were initiated in December 1992 with commercial production beginning in January 1993. The entire operation employs approximately 120 expatriates and some 800 Guyanese nationals and is expected to produce in excess of 250,000 ounces of gold per year. The total mineable reserves contain 2.5 million ounces of gold with a projected mine life of twelve years.The milling circuits feature an SABC grinding circuit, gravity concentration and a conventional CIP gold recovery circuit. This paper will review the mill start up and ""run-in"" phase during the first year of operation. Emphasis will be placed on descriptions of start up problems and circuit modifications, mill performance trends in 1993, and personnel training and development. An outlook for 1994 is also given.IntroductionOmai Gold Mines is a large scale, open pit gold mining operation located in the Potaro district of Guyana, South America, some 160 kilometers south of the capital city Georgetown. Although there are numerous small scale gold mining ventures in Guyana, particularly with the dredging operations on the rivers, Omai is the first hard rock, open pit mine to be developed in the country. At present, this mining operation is one of the largest gold mines in South America.The Omai gold deposit has been exploited for over one hundred years. In the late 1800's, a German syndicate used hydraulicing with subsequent gravimetric separators such as sluice boxes and trommel screens to recover gold from saprolite, a soft, oxidized, claylike mineral which covers much of the claim area. Through the early 1900's and up until the 1950's, numerous mining companies including Anaconda Mining Co. Ltd. explored and drilled the Omai deposit but the technology and low gold price of the day made the reserve uneconomic to develop."

Jan 1, 1994

By M. C. Irani

This survey was conducted to determine the magnitude of the methane emission and control problem in U.S. bituminous coal mines. The resultant data indicate that the emission rate for any given coalbed depends primarily on the coal production rate and on mine depth, as well as on the nature of the coalbed and the surrounding strata. An excellent correlation was found between (1) the methane emission rate and (2) the product of coal production rate and mine depth for the mines in the Pittsburgh, Pocahontas Nos. 3 and 4, and the Illinois Nos. 5 and 6 coalbeds. The highest total emission rates found in U.S. bituminous coal mines were as follows, in million cubic feet per day: Monongalia County, W. Va., 39; Marion County, W. Va., 30.4; McDowell County, W. Va., 13.1; Washington County, Pa., 11.9; Greene County, Pa., 11.4; Buchanan County, Va., 21.6; Jefferson County, Ala., 10.3; and Franklin County, Ill., 6.6.

Jan 1, 1972

By D McClelland, R Whittering

Minerals and Metals Group (MMG) subsidiary Lane Xang Minerals Ltd operates a single site copper and gold mine near Sepon in Lao PDR. Gold production commenced in 2002 and first cathode copper production was in March 2006. Plant throughputs for gold and copper are currently 2.5 Mt/yr and 1.4 Mt/yr respectively; use of a second tailings dam has commenced accordingly. Although the increased catchment area creates opportunities for more storage to reduce demand on other water sources, especially during the dry season, it also creates greater requirements for water treatment capacity.The water balance for mining operations in a tropical monsoon environment with dry winters presents on going management challenges. A successful mining operation depends on a careful balance of water inputs and outputs. The challenge prior to every wet season is having enough storage capacity to absorb potential rainfall. Plant operation in the dry season benefits from water captured and stored from the wet season which reduces the dependence on river water. Release of excess water to the environment is necessary to cope with the overall positive water balance and depends on suitable and effective treatment of water in accordance with the environmental guidelines.Ausenco has recently built and commissioned a second water treatment plant at the Sepon Copper Plant to process tailings decant water.  The objective of the second Sepon water treatment facility is to increase the site water discharge capacity to maintain the water balance and reduce the dependence on river water.  Decant water treatment is required to precipitate the contained heavy metals prior to discharging to surrounding wetlands.  The main metal that needs to be removed from the site water to meet discharge water quality requirements is manganese, as heavy metals are already precipitated to required levels in neutralisation before the tailings are sent to the storage facilities. A site layout provision for removal of manganese to produce a saleable carbonate precipitate is incorporated in the polishing plant design (future installation).

Jan 1, 2009

By Mike Trovant, Stavros A. Argyropoulos

"A fixed grid numerical model for phase change problems is proposed. The model solves for heat transfer and fluid flow, via the coupled solution of the energy, continuity and momentum equations. In addition, the numerical scheme accounts for temperature varying thermophysical properties and determines the shrinkage profile resulting from phase and density change. Simulations are run to determine the effect of varying model parameters and wall cooling rates on the location and shape of the shrinkage void formation in cylindrical casts. Results are shown for both aluminum and magnesium.IntroductionThe mathematical modeling of phase change processes (be they solidification or melting problems) entails solving for many interrelated phenomena. A comprehensive numerical simulation of the casting of a metal, for example, would have to account for: (a) heat transfer in both the solid and liquid portions of the metal and in the mold, (b) the release of latent heat during phase change, (c) fluid flow behavior in the liquid portion of the metal, (d) temperature induced shrinkage caused by liquid contraction and solidification contraction, and (e) the development of thermal stresses with accompanying shrinkage in the solid portion of the cast and mold. A schematic of the relationships that exist between the coupled equations which govern solidification is shown in Figure 1."

Jan 1, 1994

By Samuel J. Gambino

Preliminary recommendations for the Upper Northwest Interceptor 1&2 specified installation of reinforced concrete pipe using pipe-jacking methods. However, a larger one-pass tunnel constructed using precast segmental lining would provide additional storage volume. The risk of encountering unexpected conditions or events and the resulting cost impacts could differ significantly for these two options. A probabilistic life-cycle cost analysis of these alternatives was performed. This paper discusses the construction alternatives considered, the risk assessment methodology used to evaluate these alternatives, the input parameters and risk factors used in this analysis, and the recommended project which is currently being constructed.

Jan 1, 2008

By R. V. Ramani

This report is volume 2 of an eleven-volume final report for a Grant completed by The Pennsylvania State University for the Bureau of Mines to develop a dynamic general purpose computer simulation model for underground coal mining. The simulator developed under the Grant has a wide range of possible applications in the design and evaluation of underground coal mining systems from the standpoints of health and safety, productivity, and mine environment. The Master Design Simulator consists of nine free-standing function-oriented subsystem models linked together into an integrated, comprehensive model of an entire mining system. The subsystems comprising the Master Design Simulator include geology and reserves, methane generation, roof support, subsidence, production, rail haulage, cost, water generation, and ventilation. This volume of the final report describes the Geology and Reserves subsystem of the Master Design Simulator. The two functions of this subsystem are: 1) the design of a geological data library to provide input to the other subsystems of the simulator; and 2) the calculation of coal reserves and associated values and grades under various user-specified conditions. The subsystem uses a weighted moving average method to interpolate between the borehole values, and provides output in report format, graphical plots and/or storage on magnetic tape or other storage devices for later retrieval. The application of the subsystem as an independent model with test results and comparisons with other methods of computing reserves is also presented. The appendix comprises a users manual for the model, and includes a program listing.

Jan 1, 1974

By John E. Tilton

During the past several years — much to the delight of producing firms and countries — copper prices have surged from under $1 to more than $3/lb. Anyone familiar with the industry also knows that since the early 1970s the long-run trend in real copper prices has been significantly downward. This sharp contrast between short-run and long-run trends raises the issue of the forces behind these developments. What has been driving short-run prices up and long-run prices down? Simple economics suggests that it is all a matter of supply and demand. When demand is rising faster than supply, prices will rise and vice versa.

Jan 1, 2006

Atlas Copco Construction and Mining Australia identified a number of issues in regard to the skill levels, labour turnover and productivity of our service technicians. In 1994 we were experiencing a labour turnover rate of 42 per cent per annum amongst our technicians. Exit interviews were held with each individual and one of the major areas of dissatisfaction was the degree of product training provided on our equipment, compared to what is required to be competent across the range of our products. These tradespersons were prepared to accept the reduced remuneration that an OEM offers, for the benefit of comprehensive, professional training that, in theory, could be provided. The truth is that we were achieving approximately 40 per cent of our target for training hours because of the demands of field service, pre-deliveries, etc. So, the summary was the same as the industry was experiencing at that time because of skilled labour shortages, production demands, etc people were employed and thrown in at the deep end. A recipe for failure that will be successful every time.

Jan 1, 1998

By P G. Rutherford, A W. McOnie

A volcanic sequence is described from the Golden Cross Mine, Waihi, New Zealand. The sequence includes seven lithostratigraphic units comprising flow and pyroclastic units of Coromandel Group andesite and dacite and overlying Whitianga Group dacite and rhyolite which is intruded by the Golden Cross dacite porphyry and rhyolite dykes. The sequence is mineralised and is unconformably overlain by two post-mineral units, the lacustrine Waitekauri beds and Omahine Subgroup andesite.   Detailed structural analysis of mine data has identified four deformational events (D 1-D4) and related these to the gold-silver mineralising events. Faulting was coeval with the mineralization and directly controlled the development, localisation, style and geometry of the ore shoots. Mineralization developed in competent lithologies where dilation occurred during faulting. The Empire Fault is the master shear which controlled fluid flow. Mineralised veining developed in response to tectonic pulses occurring at slightly different stages as represented by the underground Empire vein complex and the open pit vein array. The mineralising events culminated with the deposition of barren calcite veins. Post-mineral movement along the Western Boundary fault appears to have offset the orebody.

Jan 1, 1995

By V. F. Parry

[Approximately 7-1/2 million tons of subbituminous coals are mined annually in Colorado, Wyoming, and Montana, of which 50 percent probably reaches domestic consumers. The moisture of these subbituminous coals is high, averaging about 25 percent when they are mined. The coals are non-caking end stack to a variable degree when exposed to normal atmospheric conditions. They are good domestic fuels, are considered to be smokeless in most furnaces, and have been used for many years in hand-fired domestic furnaces in which the practice is to employ large lutes for efficient combustion.]

Jan 1, 1941

By E. Snyders

Two alternative processes for the manufacturing of zircon products were investigated by the South African Nuclear Energy Corporation (Necsa). These were the synthesis of doped-zircon pigments from plasma dissociated zircon, and an upgrading process to convert an inferior grade of zircon into a superior opacifier for ceramic applications. A solid-state reaction process was used to produce doped-zircon pigments. The influence on the colour intensity of the pigments on a ceramic tile were compared for milled and un-milled plasma dissociated zircon (PDZ) material, prior to calcination. Pr-yellow and V-blue zircon pigments produced from PDZ with different degrees of dissociation, were also evaluated. The second zircon beneficiation process entails the upgrading of an inferior grade of zircon to a superior opacifier for ceramic applications. A calcining process in the presence of mineralizers was used to produce the product in a conventional muffle furnace. A pre-milled inferior grade zircon concentrate, with a relatively high iron and alumina content generally not suitable for high quality ceramic applications, was used in this study. The influence of the upgrading process on the opacifying properties of the zircon material was compared to that of commercially available prime grade zircon opacifier products currently being produced in South Africa. The influence of a calcining step in the presence of mineralizers with regard to the milling characteristics of the treated zircon material was also evaluated.

Jan 1, 2005

By L. Sahu, S. Bhattacharya, S. Dey

"An ideal procedure to determine the limits of flotation-based separation, as is the case with washability analysis for density separation, does not exist. Therefore, a procedure called release analysis, considered to be the counterpart of the washability process in density separation, was developed to evaluate the flotation characteristics of coal fines. Since flotation is a complex process it is necessary to know the maximum recoverable yield that could be achieved at a target ash level and what could be obtained by release analysis. Due to a number of limitations in the initial procedures, modifications were recommended by various researchers to generate an optimum separation curve. This paper presents a review of, and a discussion on, the chronological evolution of release analysis methodology over the decades. Notwithstanding the availability of a standardized release analysis procedure, such as BS 7530, the paper highlights the critical parameters involved in the procedures, such as coal type, feed characteristics, choice of reagents and dosage, operator bias, and design features of the flotation cell IntroductionCoal is a heterogeneous substance consisting of various combustible constituents (macerals) and associated mineral matter. The kind and abundance of the various macerals present in the coal, such as vitrinite, semivitrinite, exinite, and inertinite, determine the type of coal. As macerals are formed by biological degradation of different parts of the plant material, they have different properties based on their original composition. Coal cleaning processes are dependent on the differences in physical properties between the coal components (the macerals) and also between the macerals and the mineral matter. Thus the cleaning characteristics of the coal might vary from one type to the next. The cleaning processes influence the distribution and the concentration of macerals in the various size and density fractions of the cleaned product."

Jun 1, 2019

By James R. Boyle

The Bureau of Mines initiated a program to address short-and long-term objectives of wetlands restoration as a option for reclamation of lands mined for phosphate. The short-term objectives were to identify a suitable wetland test site, initiate an extensive premining monitoring plan, develop an acceptable mining plan, and recontour and revegetate the test site. These goals were accomplished using a unique combination of expertise provided by Federal and State agencies and private industry. A 6.5-ha forested wetland with an associated streambed was offered by private industry as the test site. A premining monitoring program was established and carried out from May 1982 to October 1983. A control site was established to determine ecological changes unrelated to mining. Clearing and mining began in October 1983 and was completed in April 1984. Grading and streambed restoration was completed in February 1986. Revegetation of the site was completed in February 1987. The program to meet the long-term objective of postmining monitoring is described.

Jan 1, 1988

By Collin Stewart

Bowie Resources maintains one of the most pro-active ground control programs in the U.S. mining industry today. Its guiding philosophy is that everyone in the organization, from the miners at the face all the way through the top management, are involved in ground control. Some of the unique elements of the Bowie ground control program include: ? Roof bolt operators log the stratigraphy of test holes in nearly every cut. These ?lithgraphs? are used by section foremen to determine the need for additional roof support, and they are entered into the geologic data base for use in geologic modeling and mapping. ? Underground core drilling is conducted to obtain data for CMRR and stability maps. ? Weekly ?Quality? meetings, involving mine management and technical staff, are held to ensure that ground control information is integrated into production operations. The paper will describe the program in detail, discussing the involvement of roof bolters, section foremen, surveyors, technical staff, and production managers. It will also show how the program has contributed to the mine planning process. Case histories of successful ground control interventions will be discussed.

Jan 1, 2006

By R. A. Vik

The influence of thermal treatments on the grindability of low-grade hematitic iron ores from Michigan and Minnesota was examined in bench-scale tests. Treatment factors were roasting temperature, roasting atmosphere, and ore cooling conditions. Bond ball mill grindability and work indices were used as response indicators in evaluating the condition of the ore. Of the three treatment factors evaluated, roasting atmosphere, which brought about the con version of iron oxides to magnetite, had the most significant effect; roasting temperature had the next most important effect; and cooling condition had the least effect. Optimum grindability was obtained with reduced-quenched products of both ores at 650° C, near the alpha-beta phase transformation of quartz.

Jan 1, 1971