Search Documents

By M. B. Balachandra

A three-dimensional finite element analysis was performed of an instrumented section of a double-entry coal mine in order to provide a comparison between field measurements and existing analytic techniques. The BMINES computer code was used to perform the analysis. The sequence of excavation of the entries was considered, as well as the installation of rock bolts and cribbing during the mining cycle. The materials In the region under investigation were idealized into four rock types and coal. The rocks were assumed to be isotropically elastic, perfectly plastic. Coal was represented by an elastically anisotropic (transverse isotropy) and plastically isotropic model. A fracture yield criterion of the Coulomb form was used for all materials. The strength and stiffness of all materials were substantially reduced from available laboratory data to account for in-situ properties. Qualitative trends and stress distributions obtained from the calculation were found to be reasonable. However, computed displacements and closures were greatly exaggerated and an excessive degree of inelastic deformation was indicated in the coal, especially adjacent to the excavated faces. It was established that both these effects were the result of an excessive reduction in the strength and stiffness of the materials. The analysis underscores the need for three-dimensional calculations by identifying a number of important structural response parameters that would be either outside the scope of, or misrepresented by, two-dimensional analyses. The analysis also emphasizes the need for comprehensive and accurate measurement of material properties in order fully to exploit the power of the analytical techniques to generate reliable predictions.

Jan 1, 1976

By F. W. Gray

A GEOLOGICAL study seeking to determine, for economic purposes, the value of the Sydney coalfield as a source of coal supply. Limitations of the coalfield come under two main heads: (a) Areal extent of the undersea coalfield. (b) The distance from shore at which coal can be mined at a cost of production permitting its profitable sale. Conclusions reached are that the areal extent of seams below the Phalen seam is of. small economic importance, and that non-persistence of these seams in full thickness and quality in the undersea extension of the coalfield will put an end to profitable mining before any limitations connected with distance from the shore-line become operative. With respect to the Phalen seam, non-persistence or deterioration of the seam will become effective in the western part of the coalfield, and less certainly in the eastern part of the coalfield, before operation of limitations by distance from shore. In the central portion of the coalfield, the seam probably persists in commercially workable thickness and quality to beyond the limit of mining set by distance from the shore-line. With respect to the seams above the Phalen seam between the Mountain fault on the extreme western boundary of the coalfield and the assumed termination of the deposition area on the eastern extremity of the field near South Head of Morien, there appear to be only such limitations as arise from engineering approach, distance from shore, sufficiency of strata cover between the sea-floor and the upper coal seams, and quality of the coal (with certain reservations as to the continuity of the upper seams under Sydney harbour and in the Sydney Mines-Little Bras d'Or district). Some of these seams have fragmentary land outcroppings from which their persistence seaward is assumed, and there may be other and still higher seams in the strata column which are entirely submarine.

Jan 1, 1941

Quartz, adularia and clay minerals from low-sulfidation epithermal veins at Hishikari were analyzed for their oxygen and hydrogen stable isotope compositions to establish the source of paleohydrothermal waters. Positive correlation between Au-Ag and adularia: quartz ratio, the presence of quartz pseudomorphs of bladed calcite, and Au-bearing smectite and vermiculite is indicative, but not definitive, evidence for the control of boiling on ore mineralization. Oxygen isotope equilibrium temperatures between quartz and adularia are about 220¦C and average homogenization temperatures of fluid inclusions vary between 190 to 210¦C. The calculated d18OH2O and dDH2O values (from quartz, adularia and early smectite) are consistent with paleohydrothermal fluids that were a mixture of magmatic and meteoric waters, or alternatively, the values could derive from heated meteoric water which had undergone isotope exchange during circulation through basement rock. Overall, d18Oqtz values in veins increase toward the north, most likely reflecting palaeo-fluid flow (source).

Jan 1, 2001

By David C. Uhrin

Two improved methods have been developed to transfer microfilmed mine maps to suitable base maps showing surface features. The methods provide for (1) positioning and orienting maps; (2) merging adjacent maps; and (3) plotting maps at a common scale. One method produces an overlay mosaic of mine maps using an Integrated camera-processor. This photographic method shows the details of mine workings and is most useful for specific limited-area projects. In the second method, outlines of mine maps are digitized, manipulated, and plotted as overlays using a computer. This computer method can plot mine outlines and spatially index large numbers of microfilmed maps. Microfilmed mine maps used in this Bureau of Mines study are on file in the Mine Map Repository of the Eastern Field Operations Center. The base maps are U.S. Geological Survey 7.5-minute topographic maps. The demonstration area is located in the New Kensington East and West quadrangles, Pennsylvania.

Jan 1, 1977

By Bradley S. Van Gosen, Anjana K. Shah, George M. Bedinger, Donald I. Bleiwas, Karl J. Ellefsen

"Ancient and modern coastal deposits of heavy mineral sands (HMS) are the principal source of several heavy industrial minerals, with mining and processing operations on every continent except Antarctica. For example, HMS deposits are the main source of titanium feedstock for the titanium dioxide (TiO2) pigments industry, obtained from the minerals ilmenite (Fe2+TiO3), rutile (TiO2) and leucoxene (an alteration product of ilmenite). HMS deposits are also the principal source of zircon (ZrSiO4), from which zirconium dioxide (ZrO2) is obtained for uses mostly in refractory products. Sometimes monazite [(Ce,La,Nd,Th) PO4] is recovered as a byproduct mineral, sought for its rare earth elements, and thorium (Ault and others, 2016; Sengupta and Van Gosen, 2016; Van Gosen and Tulsidas, 2016).HMS are sediments containing dense (heavy) minerals that accumulate with sand, silt and clay in coastal environments, locally forming economic concentrations of the heavy minerals (Fig. 1). Economic (mined) HMS deposits include Holocene sediments on modern coasts, such as examples in India and Brazil, as well as coastal deposits formed by transgressions and regressions of the seas during intervals in the Quaternary, Tertiary and Cretaceous, such as in Australia and the southeastern United States. Economic deposits typically contain heavy-mineral concentrations of at least two percent. Individual heavy minerals are commonly defined as minerals with a specific gravity greater than approximately 2.9 g/cm3. These minerals are generally resistant to chemical weathering and physical degradation and thus survive well in fluvial and coastal environments. Heavy minerals in coastal HMS deposits may include, in order of general abundance, ilmenite, leucoxene, rutile, magnetite, zircon, staurolite, kyanite, sillimanite, tourmaline, garnet, epidote, hornblende, spinel, iron oxides, sulfides, anatase, monazite, cassiterite and xenotime. Of these, ilmenite, leucoxene, rutile and zircon are the primary economic minerals. Garnet, monazite, cassiterite and xenotime are occasionally recovered as byproducts. The heavy minerals as a suite typically make up no more than 15 weight percent of a deposit and usually much less. Quartz and clay minerals form the bulk of the sediment. The geology of HMS deposits and examples of significant districts are summarized in Van Gosen and others (2014) and Hou and Keeling (2016)."

Oct 1, 2016

By David E. Albus, Ahmadreza Mortezaie, Bidjan Ghahreman

The structural evaluation of seismic performance of an existing hospital in Long Beach, California, required spring constants of foundation elements. The structure included support by deep foundation elements comprised of belled (underreamed) caissons. The available relationships in the governing building code (ASCE41-13) to compute axial stiffness is not applicable due to the belled configuration of the caissons. The large diameter of the bells required consideration of the foundation medium to the axial stiffness; a detail not clearly described in ASCE 41-13. Furthermore, prescriptive equations in ASCE 41- 13 used to estimate lateral stiffness only consider pile groups with the assumption that the only source of lateral stiffness is the axial reaction of individual piles. These assumptions were invalid for the project at hand where all caissons are configured as single foundation elements, not a pile group. In the present work, the approach taken to estimate seismic stiffness of single-belled caissons is described which accounts for the elastic behavior of the foundation medium below the bell base and lateral behavior of single-pile shafts. Results of the work provide a more satisfactory derivation of the spring constants consistent with current modeling methods. INTRODUCTION Seismic evaluation of an existing hospital in Long Beach, California, required geotechnical investigation followed by site-specific ground motion analysis. This evaluation was required by the Office of Statewide Health Planning and Development (OSHPD) in order to meet the requirements of the Structural Performance Category 4D (SPC-4D) published as a part of the 2016 California Building Code, CBC (Section 3412A). SPC-4D utilizes ASCE41-13, as modified by OSHPD, and involves two seismic performance objectives: BSE-1E (20% probability of exceedance in 50 years) and BSE-2E (5% probability of exceedance in 50 years). Spring constants and capacities of foundation elements were needed for evaluation of the structural performance of the building subjected to these two performance objectives. Our review of the as-built foundation plans indicated that both shallow footings and caissons were used for support of the structure. The plans demonstrated that all caissons are belled (under-reamed) and are individual, i.e. not part of pile groups. In this paper, the subject site condition and foundation elements are described first. This is followed by details of assessing spring constants and vertical capacities for belled caissons. The new requirements of the 2016 CBC concerning the evaluation of critical facilities will likely entail evaluation of other structures with belled caissons due to the more extensive use of these foundations in the past. This paper proposes a method to address the conditions of individual belled caissons not explicitly considered in the current code provisions.

Jan 1, 2018

By Oliver Bowles

THE most important non-metallic mineral industries from a tonnage standpoint are those that are allied with the construction industries and are engaged in handling sand and gravel, crushed stone, building stone, cement, lime and gypsum. The greatest problem facing a number of these industries at this time is over-production. They have experienced un- usual, and in some instances phenomenal, growth during recent years, stinlulated by extensive highway and building construction, but in some localities expansion of producing plants has far outstripped industrial needs. The cement industry is operating at about two- thirds capacity. Over-production tends toward price- cutting and unprofitable and interrupted operation, involving maintenance expenses for idle plants and disorganization of working forces. This condition has encouraged active efforts toward reducing production costs by the introduction of labor-saving equipment. Also, there is a tendency toward the location of manufacturing plants, wherever possible, near the centers of consumption rather than at points of production of raw materials. In order to reduce overhead expense, or for other reasons, many consolidations of companies into larger units have taken place. An economic study of conditions in these industries is highly desirable. The U. S. Bureau of Mines has taken one step forward in this direction in the issuance of Economic Paper 7, entitled "Economics of New Sand and Gravel Developments." Briefly, this report emphasizes the importance of making a thorough study of all the economic factors involved before undertaking new .enterprises.

Jan 1, 1930

By A. D. Dalvi

Economics, Resources, Environment and Technology are the major driving forces in the base metals industry. However, these factors are intertwined and together will propel the industry in the future. The demand for metals has grown with economic expansion, between 2 to 4 % p.a. The current growth cycle has been driven by economic expansion in China where the demand for base metals has risen from - 7 % of the world demand in the 90's to - 25 % of world demand today, and rising. Base metals are commodities and their demand and price are cyclical. Historically metal prices have declined in constant dollars, forcing the industry to reduce costs, increase productivity and increase the scale of operation for economies of scale. Due to resource depletion and capacity expansion the industry is driven to expand its reserve and resource base. However, in the case of sulphide deposits of copper and nickel it appears to be a losing battle. For nickel the laterites represent a vast source at this time. Their development requires development of new technologies to make these resources economic. Emission reduction is being increasingly mandated in most jurisdictions with all governments enacting progressively more stringent regulations. The industry has been responding with technological innovation. With the Kyoto protocol there is a push to reduce energy intensity in metal production. Technological innovation is driven by all the other factors and is leading to novel ways of doing exploration, mining and processing, that would maximize resource delineation and utilization, reduce costs, increase productivity, reduce energy consumption, maximize asset utilization and reduce environmental affects. Development of alternative technologies such as Pressure Acid Leach of laterite for nickel, bio-leaching, heap leaching, SX-EW etc are being adopted to achieve the aims of the industry.

Jan 1, 2005

By Donald P. Tuchman, Robert P. Vinson, Jon C. Volkwein

Research by the National Institute for Occupational Safety and Health (NIOSH) has pursued quartz analysis for the specialized ?lter assemblies of a new worker-wearable personal dust monitor (PDM). The PDM is a real-time instrument utilizing a tapered element oscillating microbalance (TEOM®). Standard ?berglass TEOM ?lters cannot accommodate the desired P-7 infrared analytical method used by the Mine Safety and Health Administration (MSHA). Novel ?lter materials were tested with the objective of demonstrating this type of analysis. Low temperature ashing and spectrometric examination were employed, revealing that nylon ?ber candidate ?lters left minimal residual ash and produced no signi?cant spectral interference. Avoiding titanium dioxide in all ?lter materials proved to be a key requirement. Fine quartz particulates were collected on prototype ?lters in a Marple chamber, either open-faced or through PDMs during test runs. The ?lters were then subjected to MSHA P-7 analysis and the spectrometrically based analytical results for quartz mass were compared to reference measurements. Also, PDM instrumental mass readings were compared to ?lter gravimetric measurements. Results suggest that the P-7 method is adaptable to variations in ?lter materials and that quartz dust analysis by the P-7 method when utilizing the new ashable PDM ?lters can have accuracy and precision within 10% and 4%, respectively. This is within the declared 13% accuracy and 7–10% precision of the P-7 method itself. Instrument mass readings had modest positive bias but met NIOSH accuracy criteria. Continued work with specialized PDM ?lters is merited, as they are a new type of TEOM sample amenable to ashing analysis of particulates.

By Shi Hongchao, Zou Zou Xinkuan, Zhang Jichun

As drilling and blasting is carried out in an urban tunnel, which is adjacent to an existing building or structure, the balance between blasting-induced vibration reduction and drivage efficiency is a most important issue that must be resolved properly. Therefore, a new cut blast method named Stepped V-cut millisecond blasting (SV-cut) was developed by optimizing the most common used Vertical V-cut blasting method (V-cut). The most significant features of SV-cut lie in the utilization of sublevel interval charging structure and millisecond delay blasting technology in cut hole and the cut-cavity formed from outside to inside sequentially. SV-cut provides advantages of high borehole using ratio, low vibration level, and satisfied advance per attack. Based on the principal of millisecond blasting, the rock fragmentation process and the vibration reduction mechanism of SV-cut are analyzed. Determining methods of blasting parameters, which do have significant effect on vibration intensity and cut-cavity formed quality, are proposed according to the forming requirement of both outer and inner cut-cavity and vibration reduction. In order to compare the performance between SV-cut and V-cut, field blasting experiments were performed in the blasting engineering of Yamalike twin-arc tunnel, which closely passes over aged parallel tunnels. Blasting results show that SV-cut blasting is proven as an effective tunnel blasting method for both increasing blasting effects and decreasing blasting vibration. Comparing SV-cut with V-cut, the SV-cut can increase blasting drivage about 8.5% and reduce the vibration intensity induced by cut hole blasting 30% at least.

Jan 1, 2015

By Stephen E. Mosher, Suzanne D. Smith

Ground, air, and water vehicles can expose humans to substantial multi-axis vibration. Multiple input/multiple output relationships or models exist for estimating frequency response functions of linear systems1, 2. These relationships have been applied by some investigators to evaluate the effects of occupied seat vibration3, 4. Using a multiple input/single output model, this study investigated the effects of single- and combined-axis vibration in the fore-and-aft (X), lateral (Y), and vertical (Z) directions on vibration transmission to the human chest. Frequency response functions (transmissibilities) were estimated and compared for the back-on and back-off postures. Methods A rigid seat with seat back was mounted onto the Six Degree-of-Freedom Motion Simulator (SIXMODE). A flat acceleration vibration signal was generated between 2 and 40 Hz at 1.0 ms-2 rms in the single and combined X, Y, Z, XY, XZ, YZ, and XYZ axes. The signals were shifted in time so that the combined inputs were not fully correlated. Lightweight triaxial accelerometers were used to measure accelerations at the seat base (input) and at the bony manubrium of the chest (output). The maximum of nine frequency response functions (H(?)) or transmissibilities were estimated from the auto- and cross-spectra. The system transfer matrix for the XYZ inputs and chest Z output is [ ] where PxZ, PyZ, and PzZ are the cross-spectra between the three inputs at the seat base and the Z output at the chest, respectively, and Pxx, Pxy,…zz are the auto- and cross-spectra between the input signals (? not shown in Eq. 1). Equation 1 can be similarly written for the chest X and Y outputs. Matlab® was used to estimate the auto- and cross-spectral densities for calculating the transmissibilities, ordinary coherences (for single inputs), partial coherences, and multiple coherences. Results Figure 1 illustrates the major chest transmissibilities observed for the two postures. Vertical vibration showed a consistent influence on the chest X response (Chest X/Z), most likely causing chest pitch. Some chest Z responses were observed with X-axis inputs, but the results were variable and difficult to interpret. In general, other factors besides the known inputs did not affect the transmissibilities shown in Figure 1 (Repeated Measures ANOVA, P<0.05). This was

Jan 6, 2006

By David A. Lipton

In 1980, the U.S. Bureau of Mines conducted a mineral survey of the 23,500 acre Garcia Mountain RARE II area (No. 5107) in the Los Padres National Forest. Bureau of Mines data indicate a low potential fur gold, silver, and mercury resources. Twenty-nine placer samples, representative of small yardages, showed small amounts of gold or other economic mineral values. Mercury deposits in faulted siliceous rocks in the Franciscan Formation occur north of the area. Similar rocks are in the southwest part of the study area, but apparently contain no mercury deposits. Geothermal and oil and gas potential is low.

Jan 1, 1982

By Doug Anderson

Blast vibration seismograms are generally collected strictly for compliance with regulations. The peak levels (including dominant frequency) are typically all that are looked at. However, these records contain a lot more information about how a blast has performed. The seismogram is actually a record of explosive energy that was not used in fragmenting rock. The trick is to determine how to extract information that would be useful in analyzing blast performance.

Jan 1, 2013

The reconstruction of the world after the present war must inevitably be profoundly influenced by the rise and progress of New China.The principle of Chinese mathrity has been admitted by Great Britain and the United States by their abjuration of extra-territorial tights, and by the withdrawal of the Maritime Customs Administration. The United States admits equality by her declaration that Chinese are eligible for American citizenship, and the reaction to this will be swift enmity to such peoples as may impose humiliating restrictions upon Chinese citizens.Finally, the decisions of the Moscow Conference and the recent meeting of National leaders in Cairo give partnership rights to this new State in post-war reconstruction, and open the way for a rapid realization of her destiny.It seems certain that China, if so she wills, can become, within a generation or so, one of the considerable forces of the world. The toad she wiII follow will be lighted by her own inherent and intrinsic genius. Her speed of progress can no longer be forcibly influenced by other nations and the attitude towards her of somewhat contemptuous patronage hitherto adopted by the European communities bordering the Pacific Ocean must be radically modified.It is doubtful whether the European will ever reach full understanding of Chinese mentality. The Chinese &quot;way of life&quot; since the dawn of her civilization has been totally divergent from that of the European, but the enormous potential strength, due to the simplicity of their requirements and their steadfast industry, is a function of that &quot;way of life.&quot; On the other hand the trend of reorganization must obviously be towards Western standards; and a wide knowledge of the potential strength of the Chinese is possible and will be essential in our post-war world. The following, necessarily inadequate, notes are therefore offered, as an indication of the obstacles to be overcome and the capacity of the Chinese executives and operatives to overcome them.For &apos;thirteen centuries the political and social structure of China proper (ie, excluding Mongolia, Manchuria and Tibet) has been rigidly shaped by the philosophy of Lao Tze and the ethics&apos; of Confucius. This Taoism, which is described as the &quot;way of harmony&quot; with its three jewels of character, gentleness, economy and humility, advocates the minimum of social, economic and political organization and still gives the key to the Chinese character.The Mongol and Manchu conquests of the 12th and 17th centuries, respectively, could hardly be dignified with the name of war, but the superior intelligence and harder mentality of the unwarlike Chinese finally absorbed...

Jan 1, 1944

By N. I. Basuki, E. T. C. Spooner

"The Bongara area, northern Peru, contains Zn-Pb mineralization with characteristics typical of Mississippi Valley-type (MVT) systems. The northwest-southeast-trending late Triassic-Jurassic car¬bonate host rocks of the Pucará Group were locally replaced by early (D1) and late (D2) dolomite. Fluid inclusion microthermometric data from dolomite and sphalerite are typical of MVT ore fluids (78° to 187°C; ~15-23 wt.% CaCl2 equivalent), and do not show apparent covariation between temperature and salinity.Homogenization temperature data from D1 and D2 dolomite show a decrease from northern (mean Th = 138°C) to central (mean Th = 126°C) to southern areas (mean Th = 102°C), suggesting fluid flow from north to south. Assuming a geothermal gradient of ~30°C/km and an average surface temperature of ~20°C, the lower temperature limits might approximate the ambient host-rock temperatures, whereas the upper temperature limits may represent minimum temperatures of a deeper aquifer, probably at a maximum depth of ~6000 m. The lower temperature limits are also similar to the estimated temperatures if dolomitization and mineralization took place in the Late Cretaceous at ~2000-3000 m depth, probably during the formation of the Peruvian fold and thrust belt near the present day Peru-Ecuador border.Fluid inclusion data show that the fluids in each studied location had relatively uniform temperatures and salinities during dolomitization and mineralization. A significant salinity drop and a slight temperature decrease are observed during late calcite precipitation, suggesting mixing of brines with dilute, cooler fluids."

Jan 1, 2009

By Yataro Shimomura

La alza de precios, salarios y las restricciones impuestas por los controles de la contaminación ambiental produjo un aumento en los costos de minado, generando que las operaciones nacionales mineras sean cada más difíciles. Sin embargo, la industria minera logró superarlos, mejorando la tecnología del minado, mecanización y racionalización de sus operaciones. De otro lado, el uso de métodos de minado por cuartos y pilares ha disminuído, mientras que los de corte y relleno y de subniveles se han incrementado. A esto se suma que la utilización de brocas "TC" y del "AN-FO", mejoraron la eficiencia del minado y redujeron los costos. En este sentido, el presente texto señala los últimos avances en tecnología minera a partir de los métodos de extracción, perforación, así como el empleo de relleno de tajeos con relaves de flotación, logrando un desarrollo en la seguridad y eficiencia de la minería subterránea.

Nov 20, 1972

The mineral industry of Benin contributed less than 1% of the 1977 gross domestic product (GDP), which was estimated at $500 million.&apos; Other than limestone and salt, no exploitable mineral deposits have yet been discovered in Benin, which has been rated by the United Nations as one of the world&apos;s least developed nations. In 1977, the economy was further weakened by petroleum price increases and severe drought. The country continued to depend on foreign assistance, which averaged $20 million per year, to finance development projects. The country&apos;s first 3-year plan, which was put into operation in October 1977 after many delays, allocated more than $1 billion to projects in infrastructure, agriculture, and light industry. The most important infrastructure project was the expansion and modernization of the port of Cotonou, valued as an entrepôt port for the transit of goods to the neighboring countries of Niger and Nigeria. Plans called for an increase in handling capacity to 1 million tons of cargo annually, the improvement of port and cargo handling operations, and the upgrading of the efficiency of the Port Autonome de Cotonou (PAC) management system. The $46 million project was to be financed by a consortium led by the International Bank for Reconstruction and Development (IBRD) and including Canada, France, Nigeria, and Abu Dhabi. Construction was scheduled to begin in 1978 and be completed in 1980.

Jan 1, 1981

By J. L. Jambor, J. E. Dutrizac, J. B. O'Reilly

The present-day metallurgical community is quite familiar with the use of jarosites [MFe3(S04)2(0H)6 where M = K, Na, NH4, Ag, 1/2Pb, etc.] as a means of controlling iron, alkalis and sulphate in hydrometallurgical circuits. This modern precipitation technology has found an increasingly widespread application in the zinc industry111 and is gradually also being extended into the hydrometallurgical processing of copper and cobalt121 . The chief advantage of jarosite precipitation is that the iron precipitate settles and filters well, and gives low losses of divalent metals in the washed residue. Although this jarosite precipitation technology was developed only within the past twenty years, man&apos;s involvement with jarosites extends back to antiquity, and jarosites have played an important role as a source of silver in several ancient metallurgical centres. In the early days of this century, argentojarosite was an important local source of silver at the Tintic Standard mine, Dividend, Utah, where over 200 000 oz of silver were recovered from highgrade natural jarosite over a three-month period 131 . At the Matagente mine in Peru, pockets of argentiferous plumbojarosite up to 40 m thick were mined and processed by the Indians prior to the arrival of the Spaniards14-51 . In Cyprus there are vast jarosite deposits associated with the ancient mining sitesl51 , but exploitation of these jarosites has been insignificant because of their low silver values. The most extensive mining of silver-bearing jarosite, and certainly the oldest documented instance of such jarosite exploitation, was in the vast pre-Roman workings at Rio Tinto, Spain. This mine, the greatest single miningmetallurgical site currently known from the ancient world and also the oldest site of more or less continuous metal production, has witnessed many metallurgical firsts. Aside from the initial processing of jarositic ores for their silver values, the development of large-scale hydrometallurgy also seems to have occurred at Rio Tinto. As early as 1737, copper was recovered by cementation on scrap iron from the mine waters at Rio Tintol51 . Large-scale heap leaching of calcined ore commenced with the British operations in 1876 and, by 1900, raw pyrite was heap leached to recover associated copper values161 .

Jan 1, 1999

By Jon G. Bredeson

The electromagnetic noise that exists in a mining environment is quite severe and was shown to have been reasonably well documented by a number of researchers in the Phase I Report. The noise levels are such that prudent communication design requires the careful use of all the electromagnetic noise data available. A comprehensive survey was undertaken to determine techniques used in various industrial environments to achieve secure communications in the presence of electromagnetic interference. The techniques were given in the Phase I Report and are rudimentary, but have produced reasonably good results. A number of these techniques could be applied to the mining environment.

Jan 1, 1980

By Y Yamaguchi, S Nomura, M Matsumura, C Kamijo

In order to increase productivity and decrease reducing agent rate (RAR) of blast furnaces, slag content of sinter ore must be decreased. However, gangue content in iron ore tends to increase because of resource depletion. Therefore, amount of high-grade concentrate in sinter ore feeds should be increased, but this situation causes a decrease in permeability of the sintering bed so that the productivity of sinter process decreases. In order to increase the amount of concentrate, NSSMS has developed the P-type separate granulation method, RF-MEBIOS and SPEx II technologies. These technologies have been introduced to actual sintering machines. In this report, a new technology using microparticles of iron ore is proposed to increase the amount of concentrate in sinter blends. Basic experiments simulating the sinter making process using microparticles of iron ore were undertaken. Crushed pisolite, containing &gt;60 wt per cent -10 µm was prepared for binder. The pisolite microparticle binder was mixed with another Australian sinter feed ore in a high-speed agitating mixer. They were mixed for about one minute, and then granulated using a pan pelletiser. After that, they were added to another raw material mixed by a drum mixer, and then charged in a pot for a sinter pot test. As a result, when the amount of concentrate increased from 13 wt per cent to 20 wt per cent, productivity was almost kept constant using pisolite microparticle binder.CITATION:Kamijo, C, Yamaguchi, Y, Matsumura, M, Kawaguchi, T and Nomura, S, 2017. Development of an iron ore microparticle binder for increasing the concentrate content of sinter blends, in Proceedings Iron Ore 2017, pp 69–74 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017