Search Documents

The objective of this study was two-fold: 1. To perform a world literature search pertinent to the analysis, selection and design of hoisting systems and their components and to codify the search into a literature compendium. The search resulted in a technical data file of over 1500 hard copy items. The compendium index was also suitable for establishing a comprehensive computer-loaded data base on the subject. 2. To develop a comprehensive system of guidelines to cover salient aspects of analysis, selection and design of electrical, mechanical and structural components of a hoisting system with a view to establish parameters for maximum safety and efficiency of operation, installation and revision of the system. 3. (a) In-shaft equipment design and specification criteria are considered as they influence guideline preparation. (b) A comprehensive review of hoist electric drives and controls as applied to mine hoists is set forth with special reference to duty cycle calculations and their effect on electrical component selection.

Jan 1, 1988

By S. Ragab

The objective of flotation models is to predict the recovery rate of minerals from a flotation cell. In this paper a CFD?based flotation models is presented. The model uses first order rate equation, and the collision frequency is estimated using Abrahamson [1] model with input from CFD two-phase simulations. Spatial distributions of dissipation rate and air volume fraction (also called void fraction) are determined by the two-phase hydrodynamic simulations. Knowing these parameters throughout the machine is essential in understanding the effectiveness of different components (rotor, stator or disperser, jets) on the flotation efficiency. Not only the average pulp recovery rate can be estimated but also the regions of high/low recovery rate can be identified. The CFD-based flotation model presented here can be used to determine the dependence of recovery rate constant at any locality within the pulp on particle diameter, particle specific gravity, contact angle, and surface tension.

Jan 1, 2012

Engineering education has become a matter of national concern, at last, so I would like to talk about the links between the mining industry, the universities and technological developments. The Australasian mining industry and the mining schools have collaborated closely since the first school was established in 1871 and during those years there were a series of remarkable technological developments. For example:In the late 1880s George AndersoIl Richard developed chloride leaching of gold at Mt Morgan. This made a large difference to the wealth of Mt Morgan Mining Ltd.In the mid 1890s Robert Sticht demonstrated that pyrite smelting was an economically feasible process at Mt Lyell and the wealth which came to Mt Lyell Mining Co from his outstanding work made it one of the great companies in the country.During the first 15 years of this century flotation was developed at Broken Hill and it has proved to be one of the great technological inventions of this century.In the 1920s G K Williams started his outstanding work on lead smelting and refining at Port Pirie, this was work which ultimately re-wrote the text book on lead metallurgy and established Port Pirie as the mecca for lead metallurgists.In the 1920s also Frank Stillwell, later joined by Austin Edwards, established the new science of mineragraphy at the University of Melbourne. They were both great geologists, both were superb scientists and oddly enough both were outstanding athletes.In the 1930s Dr Ian Wark, a man in the front rank of Australian scientists of any period, started his outstanding work on flotation, work which resulted in a text book which remains a leader in its field today.In the 1930s also Arnold Black at Broken Hill South Ltd picked up the work which had been done at Mt Lyell many years previously and eventually wrote the papers on hydraulic fill which demonstrated that he led the world in fill technology. What a remarkable story of achievement it was, it laid the groundwork for the great industry we have today. It was possible because the industry was well supported by outstanding university schools and I would like to talk about some of these.

Jan 1, 1989

Fine Coal Evaluation by Gravity Methods

Sep 13, 2010

By Gheorghe Marin, Franco Chiesa, David Levasseur, Bernard Duchesne

Over the past 20 years, pressure die casting has evolved to a point where structural parts can now be produced by this process. This has been made possible by the development of vacuum die casting and by the development of die-castable, low iron content alloys. This resulted in the production of low porosity, weldable die-cast parts on which heat treatment may be applied. In the present paper, the influence porosities on the tensile properties of as-cast A360 tensile test bars was evaluated. This was done by casting 24 clusters, comprising three 6mm diameter test bars each, in a 280T cold chamber pressure die casting machine after a steady dynamic equilibrium had been reached. Modeling of filling allowed to explain the differences in porosity observed in the 3 samples of a same cluster while the results of solidification modeling were related to the microstructure. Tensile samples were radiographed on a real time X-cube apparatus and separated into 2 lots: samples where no porosity defect were visible and samples with visible defects. By measuring the tensile properties of the 2 lots it was possible to quantify the drop in tensile properties brought about by porosity, which is the most common defect observed in pressure die-cast parts.

Jan 1, 2015

By Roy S. Nutter

The automation of coal mining must occur in a manner that is economically beneficial to the industry and that enhances the safety of the underground and surface workplaces. The work at WVU over the last five years in applying expert systems and neural network controlled autonomous robotics provides the mining industry with tools that when properly applied should clearly lead to mine-wide management and operational improvements and should also contribute to a higher awareness of safety issues by all work crews. This work includes the development of MMSS (Mine Management Support System) and the detailed development of autonomous robotics utilizing neural networks for mining systems.

Jan 1, 1993

By Maurizio Siepi, Fabio Santillan, Lyndon Bedford, Carlo Crippa

"Abstract: Wolf Creek dam, on the Cumberland River in Kentucky, US, operated and maintained by the Nashville District of the USACE, is the Corps' largest reservoir east of the Mississippi river. The 1748 m (5,736 ft) long Wolf Creek dam combines earthfill and concrete gravity sections. Construction began in 1941 and was completed in 1950. The dam showed signs of instability in the 1960’s, and in the late 70’s an in-depth project of rehabilitation was undertaken, using both grouting and secant piles. The works saved the dam, but in the late 90’s further signs of distress worried the Nashville district of USACE which, after a study conducted on the water seepage, concluded that construction of a new concrete barrier cut-off wall was needed. In 2009, the $341.4 USD million contract was awarded to TREVIICOS-SOLETANCHE JV.The new wall, located upstream of the concrete monoliths, has a minimum thickness of 60 cm (24 in.), and runs the length of the embankment, into the right abutment, for about 4,200 feet. The founding depth reaches 84 m (275 feet), well below the zone of solutioning. With a total surface approaching 92,903 sq.m (1,000,000 sq.ft), the Wolf Creek barrier wall is unlike any other project in the world.The construction of the cut-off wall followed a complicated but logical sequence of several operations, involving a variety of technologies: grouting, hydromill, directional drilling, and secant piles with reverse circulation. The intensive rock grouting program was aimed to minimize the risk of slurry loss and extend the positive cut-off further deep. Subsequently, an Encasement Concrete wall was installed with hydromill, toeing into the rock, to protect the embankment during the following phases. Smart holes were then drilled into the Encasement wall down to the final depth. Eventually, the holes were used to install the secant piles by employing the reverse circulation piling method.An extensive verification campaign has confirmed the superior quality of the cutoff wall consisting of 1200 secant piles, exceeding by far USACE’s requirements. The main project was substantially completed in early 2013. A small portion of secant piles wall will be installed downstream of the dam, to close the switchyard, finishing the project in the early months of 2014.IntroductionWolf Creek Dam is located on the Cumberland River in south-central Kentucky. The Nashville District of USACE operates this multipurpose dam to provide hydropower, flood control, water supply, and water quality benefits for the Cumberland River system and surrounding region. Lake Cumberland, created by the dam, impounds 7,400 million cu.m (6 million acre foot) at its maximum pool elevation of 232 m (760 ft) above sea level. This lake is the largest reservoir east of the Mississippi and the ninth largest in the United States, and attracts 4.89 million visitors, more than Yellowstone National Park (2.87 million).This paper describes the recently completed works for the rehabilitation of the dam, accomplished by TreviICOS-Soletanche JV with the construction of a new Barrier Wall."

Jan 1, 2014

Basic parameters affecting the stability of foams have been studied. We used the thin film pressure balance (TFPB) technique of Scheludko and Exerowa (1959) to measure the surface forces in foam films stabilized with various frothers such as pentanol, octanol, MIBC, and PPG. The results were compared with the froth stabilities measured using the shake tests and the film elasticity calculated using the model developed by Wang and Yoon (2006). It was found that the froth stability is controlled by both film elasticity and surface forces (or disjoining pressure), the relative contributions from each changing with frother concentration and type.

Jan 1, 2006

By Bradley V. Johnson, Robert J. Timko, Edward D. Thimons

Water-jet-assisted cutting involves the use of a mechanical cutting bit in combination with a high-pressure water jet directed just in front of the bit tip. Such a jet can offer benefits in terms of improved cutting, reduced dust and fines, and improved bit wear. The Bureau of Mines, through a contract with the British National Coal Board, has researched the use of water-jet-assisted cutting on roadheaders. After several engineering design problems were overcome, this program led to the successful underground testing of these roadheaders. Today, more than 60 water-jet-assisted roadheaders are in operation around the world and numerous others are on order. This paper details the evolution of these machines and the benefits to be gained by their use.

Jan 1, 1987

By J. R. Hindman

The vermiculite review arrived too late for the June issue. In 1992, production of commercial vermiculite in the United States increased 1 % to 170 kt (187,000 st), according to the US Bureau of Mines. The estimated value of vermiculite concentrate was $13.6 million, yielding an average value of $80/t ($72.50/st). Vermiculite is used in several physical forms. Use of the thermally exfoliated product include light weight aggregates, horticultural growth media, thermal insulation applications and absorbents for spill control and liquid waste containment. The untreated commercial concentrates are used as intumescent fillers in plaster board, gaskets and paints. Several chemically modified vermiculite products include clay-sized dispersions and granules for treating flue gas. South Africa was the only major foreign source of vermiculite used in the United States. It exported about 40 kt (44,000 st) to the United States last year. In 1992, Palabora Mining Co. began processing vermiculite in a new beneficiation mill at Phalabowra. It produced about 164 kt (181,000 st). Minor sources of foreign vermiculite concentrates consumed in the United States included about 140 kt (154,000 st) from China. Brazil also exports some concentrate to the United States.

Jan 1, 1993

By K-H. Frohne

This report presents a study of the Cooper sand of the Fork Run pool of Warren and McKean Counties, Pa., and a prediction of the secondary oil recovery by gasflooding the reservoir. A computer program employing a modification of the Craig, Geffen, and Morse secondary recovery calculation was used to make the gas flood performance forecast and is presented in the appendix. The Cooper sand reservoir in the Fork Run pool lies at a depth of about 1,900 feet and covers an area 1/2 mile wide by 2-1/4 miles long. Original oil in place is estimated to have been 8,266,000 STB. The primary recovery mechanism is solution gas drive, and ultimate primary recovery may reach 20 percent over a well life of 90 years. Two computer predictions were made for gas flooding the Cooper reservoir. The first was for a 25-acre pilot five-spot utilizing existing wells, but project economics were poor since only 25 percent of injection gas is utilized for pilot oil recovery. Recovery was 71,000 STB, or 22 percent of oil in place at flood initiation, but required 25,700 scf gas injected per STB of oil recovered. In the second prediction, pilot area performance was projected for the entire Fork Run pool, and economics became good. Recovery was 1,753,000 STB from 25 five-spots after the injection of only 6,400 scf per STB of oil recovered.

Jan 1, 1969

By Samer Sadek

The Georgia Department of Transportation (GDOT) undertook an exploratory feasibility study to one of the most ambitious tunneling projects in the United States. HNTB Corporation was retained to perform the study, deemed the Atlanta North-South Tunnel, which is approximately 7 miles long and consisting of four lanes (or six lanes) starting at the southern terminus of SR 400 extending to the south connecting with the northern terminus of I-675, providing substantial relief to the Downtown Connector (I-75/I-85), the most congested portion of Atlanta?s freeway system. This paper summarizes the analysis performed during the first phase of this challenging assignment which, if constructed, would be one of the longest roadway tunnels ever built in the United States.

By Emily Wortman-Wunder

As the 2013 president of the Society for Mining, Metallurgy and Exploration, Inc., I am pleased to present the 2013 issue of the Transactions of the Society for Mining, Metallurgy and Exploration, Vol. 334. The timely publication of professional papers that promote the advancement of scientific and technical knowledge is critical for enabling technology transfer. SME plays a key role in this process through its publications. Communication within the mining community is the key to a successful profession and society. This technology exchange continues a tradition that dates back to the 1871 meeting of 22 mining engineers in Wilkes-Barre, PA, that resulted in the founding of AIME; those individuals envisioned that these transaction volumes “would form a most valuable and greatly needed addition to our professional literature.” This volume fulfills that pledge. The 2013 Transactions contains 73 papers covering most every aspect of the mining life cycle and encompassing the diverse sectors of our industry including coal, industrial minerals, metals, health and safety and computational methods. It includes all 18 papers published in 2013 in the Technical Papers Section of Mining Engineering magazine (Vol. 65) and all 33 papers published in 2013 in Minerals & Metallurgical Processing (Vol. 30). Additionally, this volume contains 22 papers that are being published for the first time in this issue. The papers presented in this volume were written by some of the most distinguished professionals in the industry worldwide. Some of the many research highlights from 2013 include discussions of perennial issues, such as how to adequately prepare the next generation of mining engineering students for the workforce (Frimpong et al., pp. 44-52) and how to predict and prevent coal mine bursts and bumps (Pariseau, pp. 60-68), the highly anticipated February Rare Earths issue of Minerals & Metallurgical Processing, and papers analyzing electrical injuries in the U.S. Mining industry (Homce and Cawley, p. 367-375) the latest in assessing the safety and efficiency of operations. All 73 technical papers were peer-reviewed. The process of review and publication requires much hard work by authors, reviewers and our publications staff. As the 2013 president of SME and on behalf of all our members, I would like to extend our gratitude to all whose volunteer efforts contributed to the publication of this volume.

Jan 1, 2013

By M. Mirnezami, J. A. Finch, S. Uddin

A fast, reliable and practical way of measuring zeta potential using sedimentation potential method is proposed. A cell was designed along with the instrument control software to determine the required variables simultaneously i.e. sedimentation potential, specific conductivity, volume fraction of solid as well as pH. High purity alumina and silica powders were used as test samples. Measured zeta potential using the proposed technique was comparable with the results by electrophoresis.

Jan 1, 2009

By Hideharu Fukunaga, Jin Pan

"The recognition of Metal Matrix Composites (MMCs) as a means of providing high specific strength, high specific stiffness, excellent wear resistance, low thermal expansion and improved high temperature properties has led to a number of new processing, not previously used for plastic and ceramic matrix composites. As a primary fabricating process, the liquid methods are the major ones, which are reviewed briefly from the view of processing terminology. One of them, squeeze casting process is the most traditional and well-developed, because it is rapid, versatile and near-net shape production of materials. Two of new squeeze casting processes are presented to offer the hardness· controlled MMC and the· functionally graded MMCs as well as a newly developed whisker preform.I .IntroductionA large number of liquid processes and techniques including semi-solid liquid process are proposed. The most primitive process is ''pressure infiltration casting” of liquid metal into the fiber preform. It is called as follows depending on pressure and its source squeeze casting (1-4) by hydraulic ram, gas pressure infiltration casting (5, 6), vacuum infiltration, centrifugal casting (7), Lorentz-force-driven infiltration (8). The pressurizing on the liquid metal requests a large and stiff equipment, so pressureless infiltration technique has been developed using K2ZrF6 flux (9,10) while the mechanical properties are not high enough, and using H2 gas with Mg alloying element called pressureless infiltration casting (11-13), spontaneous infiltration process (14) and PRIMEX (15). In those processes, no severe reaction occurred between the reinforcement and matrix molten metal. In early l 990's, the reactive processing with pressure or without pressure, in which one material is totally transformed into another of the required shape, eq. assisted oxidation, has been developed, called reaction squeeze casting (16,17), DIMOX (18) reactive infiltration casting (19,20), and in-situ process (21,22). Die casting of SiCp/Al alloy (23,24) and thixocasting of SiCp/Mg alloy (25) are also applied to produce the machine component of MMCs."

Jan 1, 2000

By Flávio Parreiras Marques

A microabrasão é uma técnica para produzir desgaste abrasivo em escala micrométrica. Neste trabalho estudamos uma liga fundida de cobalto com composição química próxima à da superliga comercial Stellite 6com composição eutética sendo a matriz constituída por uma solução sólida de cobalto, cromo e molibdênio que embebe uma grande quantidade carbonetos eutéticos de cromo. O objetivo deste estudo é avaliar a resistência ao desgaste bem como os micromecanismos dominantes através de ensaios de microabrasão. Foram usados três diferentes tipos de lama abrasiva, sílica, alumina e carbeto de silício com uma concentração de 0,1 g/cm3, carga de 0,3 N e uma distância deslizada de 48 metros. O menor coeficiente de desgaste foi obtido com sílica e o maior com carbeto de silício. O micromecanismo dominante foi o riscamento com riscos em toda superfície da amostra e presença de indentações apenas na matriz.

Aug 16, 2017

By Jerry Wallace

This project consisted of blasting for expansion of a major interstate natural gas transmission pipeline pump station. The pump station handled 400-500 million cubic feet (1 l- 14 million cubic meters) of gas per day.

Jan 1, 1996

By E. R. Maize

This report is the third of a series on convergence of roof and floor in coal mines and subsidence of surface that accompanies it. The first paper5/ dealt with extraction in a mechanized mine (Montour 10) having relatively short rib lines that retreat rapidly. The second dealt with extraction in a mine (Crucible) in which coal was loaded. by hand and in which the rib lines wore long and slow-moving. The present report deals with a mine (Gibson) in which conditions approximated those in the Crucible mine, except that the distance between room centers was considerably less and the pillars were narrower in consequence. Moreover, the average cover was less and the studies were made under the steep hillside of a stream valley compared with a gently rolling surface over the portions of the second mine studied. Gibson mine lies in the east-central hart of Washington County, Pa. , approximately midway between the Montour 10 end Crucible mines on a north-south line. A cooperative agreement covering the work was made with the Hillman Coal & Coke Co. through W. L. Affelder, vice president. This paper describes the methods used in the investigation, gives excerpts from the data obtained, and offers such generalizations as appear to be justified.

Jan 1, 1940

By B. J. Breen, C. S. Mogg

Considerable borehole investigation work has been completed at a proposed site at Sellafield in Cumbria, supplemented by seismic surveys, other geophysical sensing and geological mapping. The focussing of investigation on the rock mass itself will be achieved by means of the planned underground rock characterisation facility, giving access to depths of about 800 m in the strong, low-permeability basement rocks of the Borrowdale Volcanic Group. Characterisation work undertaken during the sinking phase and interaction with continuing surface-based exploration and monitoring should permit a firmer assessment of the long-term safety of a repository. Key considerations in the choice of a design for the repository include the waste handling method, underground inlet cell, underground vaults, vault environment and environmental effects

Aug 1, 1994