Search Documents

By G. C. Wallick

Since the appearance of the paper, "Solution of the Equations of Un-steady State Two-Phase Flow in Oil Reservoirs," by W. J. West, W. W. Garvin, and J. W. Sheldon,' a two-fold investigation of this subject has been carried out. One objective of the investigation has been to deter-mine the feasibility of solving such problems 7on a medium-size com-puter such as the Datatron*, and the other objective has been to in-vestigate the application of such cal-culations to experimental and theo-retical petroleum reservoir research. In the first Datatron calculations, the fluid and rock properties published by West, et al, were used, together with the published equations describ-ing the system. Details of the formu-lation not given in the original paper are discussed in the Appendix to this note. Reference should be made to the subject paper for the complete equations and defintion of symbols. An unexpected result of this in-vestigation was the discovery that the linear solution published by West was in error. Thus, in addition to describing the Datatron solutions and to discussing certain numerical diffi-culties which will be encountered if one uses the published method of solution, the purpose of this note is to indicate the nature of this error. LINEAR FLOW Since the linear case requires a minimum amount of scaling, a fixed-decimal point Datatron program was written for the one-dimensional flow problem and an attempt was made to duplicate the solution described by West. In the case described, fluid was produced at a constant rate, Q, until such time as well pressure reached 0.04. Production was then continued at constant pressure. From the constants and curves given by West it was determined that the ini-tial constant production rate could be approximated by Q = 0.007. An ini-tial dimensionless time step ?t = 0.434 X 10 - "as used, and each suc-cessive time step was doubled until a value of = 0.444 was reached. This constant interval was then used for the remainder of the solution. In subsequent solutions, several varia-tions in the time schedule were em-ployed, including smaller time steps and slower rates of increase in the time steps. In all cases, almost identical results were obtained regardless of the time schedule employed. However, as described below, it was noted that the time schedule had some influence on the rate of convergence of the solutions. As a check on the accuracy of the solution, the cumulative production at each time step was calculated using the two methods described in the Appendix. Satisfactory agreement was observed with the differences in these two values of the order of two parts in 50,000. It should be noted that the mass balance check as described is of questionable value, particularly with regard to the well pressure and saturation. This is especially true in the radial solution where pressure and saturation values near the wellbore would make only a negligible contribution to the numer-ical integration. It is believed, how-ever, that such a comparison is ot value in determining the over-all accuracy of a solution. In comparing the Datatron solu-tion with that published by West it was discovered that in the later stages of depletion, the pressures near the well declined more rapidly in our solution than in the West solution, and that the limiting well pressure of 0.04 was reached at an earlier time than that originally reported. It thus became evident that it would be impossible to duplicate the production schedule described by West and a constant rate of production was maintained until the well pressure was equal to 0.0. A representative comparison of the results published by West with those obtained in this investigation is shown in Fig. 1, which is a plot of GOR as a function of cumulative recovery. These two curves should be in agreement until a cumulative recovery is reached which corresponds to a well pressure of 0.04 — for the Datatron solution, a recovery of approximately 5.6 per cent. Actually, a major disagreement is evident. Subsequent correspondence

Jan 1, 1958

By J. Jones-Parra, R. S. Reytor

The porosities of fractured limestone reservoirs can be divided into two broad types in accordance with their effects on fluid distribution and fluid flow. In the coarse porosity, gravity segregation lakes place freely and the resistance to fluid flow is very small. In the fine porosity there is no segregation and a high resistance to flow, and it has relative permeability characteristics similar to tight sandstones. By analyzing the affect of the two porosities it is concluded that in some cases to recover the maximum amount of oil it is necessary to remove large quantities of gas from the reservoir by producing at high gas-oil ratios. In this manner the fine porosity is drained of its oil and the gas-oil contact drops slowly permitting higher production rates from the oil leg. Since this conclusion is contrary to widely accepted principles of conservation, a mathematical model (Fig. I) was constructed to duplicate the conditions desired. The behavior of the model indicates that under certain conditions it is possible to recover more oil by producing at high gas-oil ratios than by production at low gas-oil ratios, and that the rate of production is affected more by gas shut-offs than by the decrease in pressure (Figs. 2, 3, 4 and 5). INTRODUCTION It has been noted that certain limestone reservoirs behave in such a way as to indicate that there are two distinct types of porous spaces available for fluid storage and fluid flow. Regardless of the nature of these porous spaces the distinguishing characteristic is that in one type of porous space there is definite gravity segregation between the oil and the gas; while in the other, the gas evolved tends to remain distributed equally throughout the reservoir. For the sake of simplicity the porosity in which gravity segregation takes place at a fast enough rate to affect the behavior will be called "coarse po- rosity", while that in which this is not so will be termed "fine porosity". The behavior of a reservoir of this type would be different than that of a sandstone reservoir, especially if most of the oil is in the fine porosity. It has been observed that fluid flow to the wells takes place mostly through the coarse porosity. The large fractures which

By J. F. Barkley

To aid in winning the recent world war, the Bureau of Mines conducted a National Fuel Efficiency Program, directed to commercial plants throughout the Nation, to save greatly needed fuel, a basic resource vital to industrial production. In planning this program it was realized that to accomplish a satisfactory reduction in fuel consumption in any plant, it would be necessary to reach, enthuse, and usually educate to some extent the actual operators of the various types of plant equipment. A major part of the programs consisted, therefore, of visits to plants and work with the operators, including a review with them of their operating conditions and of educational and guiding literature pertinent to the operating problems involved. Through a Nation-wide organization, local volunteer engineers served in making visits to local plants. Each cooperating plant appointed an employee as the "waste chaser," who headed the work of saving fuel in that plant. The educational literature was designed to interest the operator, as well as serve as a guide in eliminating waste of fuel. Volumes have been written on many subjects relating to the saving of fuel. Writings of the treatise type contain considerable good information but do not have wide appeal and probably will be read only by a few studious operators. The problem is not one of getting clown on paper everything that the experts know and would like to have the operator know, but rather to write something that will actually interest the operator and stimulate him to action. Past experience led to the adoption, therefore, of the "quiz-sheet" type of writing, using a quiz sheet of not more than two pages for any principal item. The results obtained during the National Fuel Efficiency Program in many types of plants further demonstrated that the short quiz sheet is satisfactorily appropriate and does accomplish results. Each sheet was prepared and checked by many engineers expert in the particular subject matter of the sheet. Committees of men with much experience in the manufacture and operation of equipment and in the

Jan 1, 1947

By B. W. Prof. Frazier

I PROPOSE in this paper to treat of the chimney merely as a heat engine, as one of the devices resorted to in practice for the conversion of heat into mechanical work. For the sake of simplicity and clearness in the discussion, let us consider the subject in its simplest form. Conceive a chamber, heated from without, in free communicatioH at one end with the external atmosphere, and at the other end opening into a vertical chimney. Let the. cross-section of the chamber be so great, relatively to that of the chimney, that we can neglect the actual energy of the air passing through the chamber. We will neglect, also, all passive resistances to the passage of the air. We will assume that the cross-section of the chimney is constant, and that the air in passing through it neither gains nor loses heat. The following symbols will be employed in the discussion : Po = the normal pressure of the atmosphere, which, it is assumed, is the pressure existing at the level of the chamber. Po = 10332.96 kilograms per square meter. P2 = the pressure of the external atmosphere at the top of the chimney. To = the, absolute temperature of melting ice by the centigrade scale. This is assumed to be the temperature of the external air at the level of the chamber. To = 273°. T2 =the absolute temperature of the air as it passes from the chamber to the chimney. T3 =the absolute temperature of the air as it issues from the chimney. to, t2, t3 are the temperatures, as recorded on the centigrade ther¬mometer, corresponding to the absolute temperatures To, T2, T3 re-spectively to = 0° C. In general, t = T- 273. Io, I2, I3, represent the intrinsic energy of the air at the temperatures To, T2, T3 respectively.

Jan 1, 1882

By Javier Támara

Para aumentar la productividad de la empresa minera es necesario conocer el sistema de aire -en tanto se prioriza los intereses de los clientes, y así se puede suplir todos los componentes necesarios para garantizar una máxima eficiencia y confiabilidad del sistema completo de aire comprimido que va desde el filtro de admisión hasta el punto de uso. En ese sentido, el presente texto describe las estrategias para realizar Solucionazing en ahorro energético y así aumentar la produtividad de los sistemas de aire.

Aug 25, 2002

By M. J. Mullikin, J. B. Conway

Equations capable of representing combined first -and second-stage creep behavior include the Andrade, Cottrell-Aytekin, Garofalo, and de Lacombe equations along with a third-degree polynomial in t1/3. Employing some recent high- temperature creep data for arc-cast tungsten the effectiveness of these expressions was evaluated. It was found that, in this instance, the most accurate representations were afforded by the third-degree polynomial in t1/3 and the de Lacombe equation. Also noted was the fact that the Andrade equation gave results just slightly inferior to those obtained with the third-degree polynomial, definitely better than those due to the Cottrell-Aytekin equation, and slightly superior to those furnished by the Garofalo equation. EXPRESSIONS designed to describe combined first -and second-stage creep behavior must possess certain specific characteristics. At time zero the equation must reduce to a strain value corresponding to the instantaneous deformation on loading. Then in the early moments following load application transient-creep behavior must be described to reflect a creep rate which constantly decreases with time. And finally at larger time values linear (or at least nearly linear) strain-time behavior must be accounted for to yield the steady state or minimum creep rate. Some equations, such as the one based on the parabolic creep law, yield fairly satisfactory results in transient analyses but are not effective at all when combined first- and second-stage data are to be analyzed. Other equations give equally accurate results in both instances although in general the complexity of the equation is slightly increased. For example the Andrade1 equation: has found fairly general application in expressing first-stage creep behavior. Furthermore the contribution of the exponential term becomes more and more prominent as the time increases and causes this equation to exhibit a point of inflection at large values of time. With a proper selection of equation constants the curve can be made fairly flat in the region of the inflection point indicating a desirable equation form for combined first- and second-stage creep analysis. Another equation form with the proper characteristic is that of Cottrell and Aytekin:2 e =a +bt1/3 +ct [2] Obviously as time increases the first derivative of this expression approaches a constant value to suggest application to combined first- and second-stage creep analysis. Similarly a third-degree polynomial in t1/3: e -a + bt1/3 + ct2/3 +dt [3] has the same characteristics. Expressions of this type have been shown3 to be very effective in the analysis of transient-creep behavior and the fact that the first derivative has the same characteristic as Eq. [2] suggests use in the combined analysis.

Jan 1, 1967

The Torington Lodes.This paper describes investigations into mineralogical, petrological and structural associations of cassiterite in occurrences of economic value. The work was carried out in three mines, during a number of years, in the hope that the, data collected might be helpfulin the search for occurrences of cassiterite in stanniferous zones and reduce unproductive exploratory work. Tin-bearing lodes at Torington, in the New England district, New South Wales, have been worked since 1880, and the locality is the most important centre of lode tin occurrence in the, State. The township of Torington is 18 miles westerly from Deepwater, a station on the Great Northern Railway, 446 miles from Sydney.The tinfield forms part of the Mole Tableland, which has an altitude between 3,000 ft. and 4,000 ft. above sea level. The country rock, in which the stanniferous lodes occur, is granite of Permian age, which has been intruded into Carboniferous claystone. An inlierof claystone is exposed to the west of the stanniferous area, 'and in it, close to' its contact with the enclosing granite, are occurrences of wolfram and bismuth. These minerals, together with chalcopyrite, pyrite, arsenopyrite, zinc blende, galena and molybdenite, in very small quantity, are associated with cassiterite in lodes traversing the granite, particularly near the claystone, but decrease in amount with distance from the contact. Their occurrence is sporadic and usually causes no trouble in dressing the cassiterite concentrate, the final product containing less than 1% of total penalisable impurity. In Curnow's mine, pyrite, galena and molybdenite have been observed at 700 ft. from surface.The granite is of the biotite type and its structure may be divided into four groups, or classifications, arising from segregation processes during cooling and consolidation. The four classes, in order of extent of distribution, are:1. Granite of normal type, in which the constituent quartz felspar and mica, have a particle size approximately 14, in.2. Porphyritic granite, in which the felspar particles are from % in. to lin. in size, that of the quartz and mica approximately % in.3. A fine-grained granite, in which the particles of all constituent minerals are % in. or less in size;4. A rock of highly siliceous ground mass containing very small particles of felspar and almost negligible biotite.Type 1 is the general type of granite in all mines of the field; types 2 and 3 may occur as large masses, or all three classes may merge rapidly one into the other, and all be disclosed in 20 ft. of driving. Usually, however, the segregations are massive, but are not associated with any special horizon. For instance, a mass of porphyiiticgranite extends from surface to a depth of 440 ft., for a distance of 350 ft. south from the New England main shaft. The upper levels of Curnow's mine, 14" mile south-east, are in normal granite, but a restricted mass 'of porphyritic granite occurred between Nos. 5 and 6 levels, or 400-500 ft. below the collar of the shaft...

Jan 1, 1950

By D. L. Petersen, C. R. Nelson, B. K. Nelson, B. D. Wagener

The Lafayette Bluff tunnel, currently under construction for the Minnesota Department of Transportation (MnDOT), will be among the widest highway tunnels in the United States. The 199-meter tunnel is being constructed in a closely jointed, variably weathered diabase rock mass. Cover above the tunnel crown ranges from 4 meters to 27 meters, and is less than the tunnel excavated width of 18.3 meters for about 60 percent of its length. These factors dictated special support and lining design, limitations on excavation sizes and required sequences for support installation. Tunnel excavation is by controlled blasting, with multiple top headings and bench. Rock support and lining consists of external portal beams, rockbolts and reinforced shotcrete. A final concrete lining provides structural support for the rock mass and the membrane waterproofing system.

Jan 1, 1991

By D J. Brake

There has been a strong trend over the past decade in hard rock mines towards the use of very high powered auxiliary (or secondary) fans; in many mines, the installed power for the secondary ventilation system now exceeds that of the primary ventilation system. This also reflects the trend to use two-stage auxiliary fans pushing air into a single ‘trunk’ duct that in turn splits into multiple branches with multiple outlets feeding multiple workplaces. This often produces a poor result in terms of face flows due to the high resistance, high leakage and badly managed duct outlets, as well as high fan capital and operating (power) costs, which in turn also results in a higher cost for the underground power reticulation/distribution systems. This paper explores the reasons why this trend exists and what ventilation practitioners can do to utilise less expensive systems that simultaneously deliver better workplace conditions. It includes a case study.CITATION:Brake, D J, 2017. Auxiliary ventilation design – why and how mines waste so much power on inferior systems, in Proceedings Australian Mine Vent Conference 2017, pp 27–34 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By D. Witchard, G. C. Penny

An important conclusion of the study is that altering the properties of the granulation water is a practical way of improving the sintering performance of blends that contain porous ores, and more work is under way to investigate other additives. Previous studies of iron ore blends containing pisolite ore showed that losses in sintering productivity were a result of deteriorating green-bed permeability. Pisolite ores are extremely porous and absorb a proportion of the water added during granulation. Although increased water addition could be used to counteract losses in productivity, the current study examined methods of inhibiting water absorption by pisolite ore as a means of improving productivity. Additives were used to alter the properties of the granulating water. With no increase in mix moisture contents pilot-scale sintering studies showed that sugar-based additives gave productivities that are higher than those obtained for a comparable ore blend containing haematite rather than the pisolitic ore. Several techniques of adding the sugar to the sinter mix were examined and found to increase productivity to varying degrees. Theoretical considerations, in some cases supported by experimental results, indicate that sugar-based additives not only inhibited water absorption by porous ore particles but also improved the permeability of the sintering bed. The study also suggested that, contrary to some commonly held views, the highly reactive nature of Yandi ore from Western Australia is beneficial for sintering. Porous ores enabled the formation of a strong sinter at fast flame-front speeds-both good strength and a short sintering time are requirements for high-productivity operation

Jun 18, 1905

By T. Proietti, L. Mongiovì, L. Simeoni

Reliable estimates of the kinematic characteristics of movements are obtained by using a statistical model SSM. This model represents a useful tool for the management of alert and alarm systems. L'élaboration des données du déplacement médian d'un modèle statistique SSM opportun fournit des estimations fiables des caractéristiques cinématiques du mouvement. Le modèle peut être ainsi utilisé pour la gestion des systèmes d'alarme. Die Bearbeitung von Bewegungsdaten anhand eines geeigneten statistischen Modell SSM ergibt vertrauliche Abschätzungen der kinematischen Eigenschaften der Bewegung. Das Modell kann also für das Management von Alarmsystemen verwendet werden.

Jan 1, 2003

By P. T. Brooks

Mineral nodules from the ocean floor represent a vast potential source of manganese, nickel, cobalt, and copper. Process development studies to devise methods for recovering these metals were conducted by the Bureau of Mines using two types of nodules--relatively low-grade calcareous nodules from the Atlantic Ocean and higher grade siliceous nodules from the Pacific Ocean. Ammoniacal carbonate leaching of reduced nodules appeared to have the best potential for processing the calcareous nodules, but the method proved to be impractical for recovering manganese. Extraction of 90 percent or better of the nickel, cobalt, and copper showed the technique to be attractive for recovery of these metals. The siliceous nodules appeared amenable to a process that starts with either a sulfur dioxide leach or a sulfation roast followed by a water leach to dissolve the soluble sulfates.

Jan 1, 1971

By David R. Jessey

Water pollution problems associated with surface metal/nonmetal mines throughout the United States were assessed. Three major problems were identified: acid mine drainage (AMD), toxic concentrations of heavy metals and excessive sedimentation. Several factors affect the type and amount of pollutants generated at a mine site. Among these are hydrologic regime, geology, mineralogy, topography, climate, size of the mineralized area and mining method. Nine surface mines situated in distinctly different settings were visited and their pollution problems studied. These mines were located in Morenci, Arizona; Hayden, Arizona; Sauharita, Arizona; Cobalt, Idaho; Spruce Pine, North Carolina; Iron Mountain, California; Butte, Montana; Fernwood, Idaho; and DeLamar, Idaho-Oregon. A detailed evaluation of the pollution problems at the Morenci mine indicated that a diversion system and treatment pint would be the most effective means of abatement for the existing water quality problems. Based on the study of the Morenci mine and three other porphyry copper mines with differing problems a water management plan was conceived for a new source copper mine. A companion Appendix Volume containing detailed reports on the mine site visits is on file at the US Bureau of Mines Spokane Research Center.

Jan 1, 1981

By Michael E. Berndt

Asbestos first became an issue to Minnesota?s iron industry when it was revealed that mineral fibers similar to those in Reserve Mining?s tailings were being found in drinking water for several communities that used Lake Superior as their primary water source. This discovery turned what had largely been an environmental court battle into a case concerning public health. The courts listened to much conflicting and uncertain scientific testimony on the size and distribution of the mineral fibers and on the potential health effects imposed by them. In April 1974, the plant was ordered to shut down by a federal judge but the company quickly appealed the decision. The appeals court granted a stay and ultimately ruled that the plant?s closure could not be justified based on the unknown health effects of the mineral fibers since the consequences of such an action would have immediate and severe social and economic impacts. The plant was allowed to continue operation, but ordered to abate emissions to air around the plant and to switch to a land-based tailings disposal system. Much of the scientific uncertainty and public concern over mineral fibers in Minnesota?s taconite industry remain today. ©2007 Elsevier Inc. All rights reserved. Keywords: Minnesota; Iron ore; Taconite; Asbestos; Amphibole; Reserve Mining; Tailings; Mesabi Iron Range

Jan 1, 2007

By K. K. Kershner

The purpose of this investigation was to develop methods, on a laboratory scale, for recovering tin from Bolivian metallurgical slimes. Petrographic and chemical analyses were made of slime ore fractions from several well-known tin operations. High percentages of the total tin were volatilized as chlorides at temperatures below 600° C. Under optimum conditions reaction rates were relatively rapid, and the chloridizing reaction approached completion. Owing to the low temperatures involved and the high yields of tin, the process was considered to have possibilities for treating Bolivian slimes on a commercial basis. ACKNOWLEDGMENTS Appreciation is hereby extended to the Patino Mines and Enterprises, Inc., of Bolivia, for supplying slimed tin ores that were used in the experimental work. This company has since been nationalized.

Jan 1, 1959

By Loren R. Anderson

A probabilistic slope stability computer model was developed at Utah State University and independently evaluated by CH2M Hill Consulting Engineers as a design and analysis tool. Volume I of this report describes the model and Volumes III and IV are users manuals for the computer programs. This volume (Volume II) constitutes the report by the CH2M Hill. It includes a description of a field investigation and stability analysis of an existing tailings dam. Based on the results of the analysis, the tailings dam was evaluated for redesign using probabilistic considerations. Conclusions are made regarding the usefulness of the model as a design tool.

Jan 1, 1982

By G. R. Moulder

A device was developed that measures dynamic stress (ultrasonic energy) transfer through installed rock bolts, a measure that is directly proportional to the degree of grout bonding of the bolt to the mine roof structure and thus the ability of the bolt to bear static stress. The rock bolt bond tester (RBBT) is a hand-held portable device that shows three ranges of bolt bond condition; i.e., one-third (Bad bond), two-thirds (marginal), or fully bonded. These are shown respectively by a red, yellow, or green light that displays for 4 s. RBBT performance was verified with 2 1/2-to 8-ft bolts installed in various types 0f mine roof structures (sands tone, shale, and boney coal-mud), and 15 now being tested by the Bureau of Mines in mines across the United States. The unit is about the size of a five-battery flashlight and contains the transducer electronics, and battery pack. The RBBT is designed for extreme ease of operation, requiring only manual contact with the bolt and signal read-out. The batteries are rechargeable and the package is designed for durability in a mine environment.

Jan 1, 1983

By E. McCullough, D. Preece, M. Ortel

Geophysical explosive charges are used in mineral resource exploration. They are detonated subsurface and radiate sonic waves into ground monitors, which detect the vibration waves and their interaction with underlying geologic strata. Geophysicists perform computer analyses of the waves reflected from the strata to determine their depth and thickness (Strobel, Berger & Schaefer, 2012). The purpose of this research is to determine how the detonating explosive charge interacts with the adjacent ground and how the induced waves propagate through the surrounding medium. Furthermore, it is necessary to optimize the location of the initiation point within the charge. Establishing both the direction and intensity of the waves will allow geoscientists to refine and optimize geophysical studies that employ explosive charges.

Jan 1, 2013

By Lutz Markworth, Evren Ören

"The worldwide demand of ores and the depletion of the high-purity deposits make it necessary to recover ores in increasingly finer size fractions in the feed material. The flotation technology of more than 40 years old plants was not able to recover the ultra fine material. Those slurry tailings ponds now have the chance to be re-processed with PNEUFLOT® technology.The bubble sizes of different flotation technologies have a huge influence of the results especially regarding the recovery of the ultra fine particle sizes.PNEUFLOT® technology of HUMBOLDT WEDAG Coal & Minerals Technology GmbH in Germany was applied to ultra fine Phosphate, Copper and Platinum ores. The results will be presented in this paper.Conventional technology like agitator flotation has its limits in the flotation of fines due to turbulences in the cell. The position of the agitator influences the recovery of the fines. A deep impeller generates a higher froth zone. This helps to catch the medium fines. Due to the static head of the slurry inside the cell, compressed air is required for such cell designs.Column flotation is well known for a good selectivity without having in the first cell a good recovery. This leads to invest in several cleaning stages to reach an acceptable recovery. Further more, compressed air is required to generate the air bubbles to the flotation process, which are much bigger than with PNEUFLOT® technology applied.INTRODUCTIONHigh metal prices are actually the basis to invest in poor deposits or deposits with very fine intergrown ores which have to be milled down to ultra fine powders less than 60 micron. The liberation grade has to be determined by a mineralogical analysis. Polish sections have to be prepared and interpreted by using of a microscope. Figure 1 and figure 2 are showing polish sections of a platinum-nickel ore from Petchenga Nickel at Zapolyarni Mine in Russia. The head grades for rich ore are for copper between 0.05 – 0.15%, for nickel between 3 – 7% and for platinum group minerals approx. 0.15 oz/t. With an efficient flotation technology it can be upgraded to 20 oz/t."

Jan 1, 2009

By G. W. Josephson

JUDGING by the progressive atmosphere prevailing in the nonmetallic mineral industries during the past year, postwar conditions were healthful though inflationary. Demand for most industrial mineral products has been exceptionally high and many new production records were attained. Severe shortages of some commodities existed, especially building materials and fertilizers. Production costs and prices increased and profitable operation was general. Under these conditions expansion programs were the order of the day. Ample funds were available to finance the purchase of good equipment; and, as wages and other operating costs were increasing, primary emphasis was placed on attaining maximum efficiency in new installations. These efforts were hampered by shortages and slow delivery of desirable equipment, so compromises in design were often necessary. However, on the whole, production practice improved.

Jan 1, 1948