Search Documents

The following report summarizes the results of engineering feasibility studies whose purpose was to assess the probable efficiency, reliability, safety and cost of a number of possible methods for removal of radon gas from the ambient air in underground mines. Fourteen candidate techniques were evaluated. Seven of these were based on specific individual principles, and seven were based on combinations of these principles. The individual principles were as follows: 1. Activated charcoal 2. Organic fluids 3. Semipermeable membranes 4. Molecular sieves 4. Cryogenics 6. Chemical reaction 7. Centrifuge The combinations were: 8. Cryogenics and activated charcoal 9. Cryogenics and molecular sieves 10. Cryogenics and chemical reactions 11. Membrane filters and organic fluids 12. Membrane filters, cryogenics and activated charcoal 13. Membrane filters and chemical reactions 14. Silica and an Organic Fluid

Jan 1, 1975

By Francis Breton, Daniel Larouche, Pierre Heugue, Rémi Martinez

"Nowadays, in order to fit environmental restrictions, automotive markets are demanding cast aluminum alloys working at high temperature (180–300°C). New generations of alloys are required for higher strength components in engine downsizing or start-stop systems which lead to higher loading and higher specific power and stretch current materials to their limits. Recently, transition metals, such as zirconium and vanadium, have been added as alloying elements into an AlSi7Cu3.5Mg0.1 alloy to improve physical, mechanical, thermodynamic properties with the aim of increasing service life of parts. In such alloys, the best mechanical properties are associated with the formation of precipitates through an optimum heat treatment sequence, including: solutionizing, quenching and artificial aging. This study is focused on the modified AlSi7Cu3.5Mg0.1 cast alloy with Mn, Zr and V additions for high temperature application. The characterization of the cast alloy in this study, firstly, helps to evaluate and understand its performance both chemically and structurally according to their physical state: as-cast or as-quenched. Comparison of precipitation kinetics between a binary Al-3.5%wt.Cu alloy and the AlSi7Cu3.5Mg0.1 (Mn, Zr, V) alloy has been characterized by differential scanning calorimetry, TEM observations and micro-hardness testing. The Kissinger analysis was applied to extract activation energies from non-isothermal DSC runs conducted at different stationary heating rates. The study focuses on the impact of the chemical composition such as Si content on the kinetics parameters.INTRODUCTION Pure metal Aluminum shows poor mechanical properties and its malleability is high, that is why alloying elements are added to the mixture before casting to improve physical, mechanical and thermodynamic properties (Javidani, 2015); such as Silicon (Si) for casting properties (castability, cold crack capability, wear resistance, shrinkage behavior), Magnesium (Mg) and Copper (Cu) to generate precipitation hardening systems. Aluminum hypoeutectic alloys (<12% Silicon) with Cu, Mg additions used in the automotive industry for manufacturing mechanical parts (Larouche & Javidani, 2014) are mostly subject, after casting, to precipitation hardening heat treatment (Mohamed & Samuel, 2012) according to specifications and associated standards. The best mechanical properties are associated with the formation of precipitates through an optimum heat treatment sequence, generally including: solutionizing, water quenching and artificial aging (Manente & Timelli, 2011). Hypoeutectic aluminum-copper alloy with amount of Cu around 1 to 4.5wt% is an elementary case for precipitation in heat treatable aluminum alloys. Researchers essentially focused their work on the full precipitation sequence of binary Al-Cu alloy during aging which is presented below."

Jan 1, 2018

By A. T. Iannacchione

Underground stone mining represents an emerging sector for the U.S. mining industry. As this expansion takes mines under deeper cover and as more efficient mining methods are utilized, adequate stone pillar design methods will become more important. It is the purpose of this paper to examine current design practices and to discuss issues for safe mine layouts so that a rational first approach towards balancing the demands for increased production can be weighed against increased risk to worker safety from rib instabilities and pillar failures. Seventy-two stone mine pillar designs were examined. Pillars with width-to- height ratios below 1.5 and subjected to excessive stress levels appear more likely to fail. When width-to- height ratios fall below 1 .0, defects in the pillars, such as through-going discontinuities, can have a significant influence on stability. Discontinuity persistence, dip, material properties, and orientation are important factors controlling pillar strength. The influence of discontinuity dip, a characteristic easily identified in the field, was examined so that its presence could be accounted for in developing generalized guidelines for pillar design.

Jan 1, 1999

By J. W. Walkiewicz

The Bureau of Mines investigated alloys containing lanthanum (La), praseodymium (Pr), neodymium (Nd), cobalt (Co), copper (Cu), iron (Fe), and magnesium (4g) as possible components of a permanent magnet mate¬rial utilizing a cerium-free synthetic mischmetal (M) as a substitute for scarce samarium (Sm) metal. Magnets containing M-Co-Cu-Mg and M-Co-Cu-Fe-Mg were fabricated by powder metallurgy techniques and evaluated. A synthetic mischmetal (M20) containing 20 pct La, 60 Pr, and 20 Nd yielded the best overall magnetic properties. The M20-Co-Cu-Mg alloys had energy products as high as 13.2 MGOe, remanences as high as 7.89 kG, normal coercivities as high as 6.26 kOe, and intrinsic coercivities as high as 13.4 kOe. The best value of intrinsic coercivity, 22.9 kOe, was obtained with an M-Co-Cu-Mg magnet in which the synthetic misch¬metal contained 30 pct La, 50 Pr, and 20 Nd. These values compare favorably with those of the Sm-Co magnets fabricated and measured at the Bureau&apos;s Reno Research Center, which had energy product of 15.1 MGOe, remanence of 7.8 kG, normal coercivity of 7.5 kOe, and intrinsic coercivity of 27.4 kOe. Iron substitution for part of the cobalt resulted in a decrease of magnetic properties, although several percent iron can be added before a drastic loss of magnetic properties occurs.

Jan 1, 1983

By Robert J. Dompe

The objective of this program was to develop a cost effective microprocessor-based electronic image sensor system for monitoring pit slope displacement to detect and/ or predict impending slope failure in surface mines. A background study and data analysis yielded a performance specification for candidate Video Slope Monitoring Systems. A design concept was developed based on using a pair of solid state video cameras located on precision pointing assemblies. The digital images from the cameras are compared and, using electronic triangulation, slope topology is calculated. The current and past locations of operator selected features are compared to determine pit slope displacement. A proof-of-concept test was performed using a laboratory model of a pit slope. Based on the successful results of that testing it is recommended that an in-mine evaluation be performed using a full-scale prototype Video Slope Monitoring System.

Jan 1, 1982

By Alan A. Campoli

The mining industry has long been searching for an effective structural application that prevents weathering and falls of loose rock, debris, and sediment. J-Crete is a fiber-reinforced, engineered, cementitious composite rock application that is designed, tested, and successfully utilized as such a material. Laboratory evaluation of J-Crete material properties has shown the final compressive strength to be in excess of 7,300 psi (50.34 MPa), with 24 hour strength in excess of 1,500 psi (10.34 MPa). The flexural tensile strength is in excess of 600 psi (4.1 MPa) and is provided through a unique combination of polyvinyl alcohol (PVA) fibers activated by a proprietary liquid additive that prevents them from clumping and enables even distribution throughout the grout. Tensile bond strength in excess of 350 psi (2.4 MPa) at 28 day cure tightens the strata and holds loose material in place. Practically impervious to gas and liquids, J-Crete protects strata against long-term weathering, does not require screening to be effective, and has proven to be a successful waterproofing material. J-Crete has demonstrated the potential to alleviate coal mine roof cutters in soft, wet clay formations. J-Crete reinforces coal mine ribs by bonding directly to the rib, conforms to the strata, strengthens the rib, and eliminates sloughing due to long-term weathering; stabilizes coal mine entries by bonding directly to the brow and roof, and creates a monolithic shell with double reinforced corners.

Jan 1, 2012

By R. A. Strehlow

This is the final report for U.S. Bureau of Mines contract HO-122122, which was in effect from June 30, 1972 through January 4, 1976. The work resulted in the design and construction of a large laboratory scale coal dust burner and the use of this burner to study gaseous and coal dust flammability. A new technique for determining gas phase flammability was developed and the effect of solid and gaseous suppressants on the propagation of coal dust flames was studied. In addition, a technique for measuring the C/H ratio in the flame was developed and the C/H ratio that was measured in a coal dust flame on this burner showed that the burning process was preceeded by pyroysis of the coal dust. Both experimental and theoretical studies showed that radiative trans-port is very important to the propagation of a coal dust flame.

Jan 1, 1977

By Serge Rudchenko

A study to determine the potential use of retaining structures in open pit backfilling. Research and review of the open pit mine environment, mine waste disposal, and past and current use of retaining structures. A development of specific structures, the culvert/ tunnel concept, and an anchor block retaining concept. The cost benefit of retaining structures used for in-pit backfilled waste.

Jan 1, 1981

By P. Bracher

Most efforts to mechanize low seam (narrow reef) mining of platinum ore are presently based on board-and-pillar methods with1.6?1.8 m in reef excavation. This paper attempts to substantiate the benefits of low profile mining: primarily improved head grade with resulting reduced tailings losses. Board-and-pillar equipment supplied by DBT, facilitating1.1?1.2m mining height has been in operation in an Anglo Platinum mine since September 2001. Major aspects of the equipment, battery scoops (LHDs) and rotary bolting rigs, are described and presently achieved results reported. The medium term industry goal is rock breaking without the use of explosives. An outline of present DBT developments is presented.

Jan 1, 2003

By K. J. Stanaway

Major world ilmenite and rutile accumulations reveal similar regional geology and Proterozoic age deeper crustal source rocks. During crustal collision titanium crystallizes as ilmenite and rutile at buried sites of high pressure and temperature rock metamorphism. Hydrothermal activity can convert titanium minerals to rutile, but titanium migration and enrichment seem only local. Many melts crystallize rocks with iron-titanium oxides in solid solution, but titanium enrichment at economic scale takes place in basic intrusive melts often associated with anorthosites and charnokite. Sedimentary placer enrichments have formed since the Proterozoic with water-resistant ilmenite, and rutile segregating by gravity from quartz sands deposited from flowing water. Placers have residual, alluvial, strand and shallow marine variants. Time, organic acids, and sand permeability play lead roles in the leaching of iron from ilmenite during weathering and diagenesis.

Jan 1, 2005

By L. D. van Dyk

The extraction of iron and lead from their oxides with a volatile organic ligand such as acetylacetone in the gas phase offers potential advantages of lower energy consumption, recycling of the extractant, recovery of pure metals, and a reduced environmental impact compared with conventional extraction processes. The influence of reaction temperature, ligand flow rate, and metal oxide levels on the extraction and rates of reaction of iron and lead from single metal oxide (synthetic haematite (Fe2O3) and synthetic massicot (PbO)) systems in a fluidized bed was studied. It was found that at the investigated acetylacetone flow rates, the influence of mass transfer was limited, but that the reaction suffered from reactant starvation. When the metal load increased the effect of starvation on the rate of reaction also increased. The reaction kinetics increased with an increase in temperature for both systems. At low metal oxide concentrations more that 80 per cent of the iron and lead could be extracted from their respective metal oxides after only four hours.

Jan 1, 2012

By James C. Foley

In-situ characterizations of green state part density and sintering state have long been desired in the powder metal community. Recent advances in non-contact electromagnetic acoustic transducer (EMAT) technology have enabled in-situ monitoring of acoustic amplitude and velocity as sintering proceeds. Samples were made from elemental powders of Al (99.99%), Al (99.7%), Ag, (99.99%), Cu (99.99%) and Fe (99.9%). The powders were pressed in a uniaxial die and examined with acoustic waves for changes in velocity and amplitude during sintering. The changes in acoustic properties were correlated with mechanical properties. Evolution of a series of reverberating echoes during sintering is shown to provide information on the state of sintering, changes in sintering kinetics as well as having the potential for detection of interior flaws.

Jan 1, 2001

The early history of the mine is traced from the beginning of shaft sinking in 1886 to the purchase by the Broken Hill Proprietary Co. Ltd. in 1949. A necessary preliminary to mechanisation of the Borehole Seam was development of the Young Wallsend seam, andthis development is described. Surface reorganisation and coal handling arrangements are dealt with in detail. Then follows a description of the Borehole Seam mechanisation, the provision of power supply for this purpose, arid pumping arrangements in themine.INTRODUCTIONStockton Borehole Colliery is in the Parish of Teralba, between the townships of Teralba and Boolaroo, and about 12 miles from Newcastle. The colliery holding, a freehofd area of 2,560 acres, was apparently an original land grant when acquired by Teralba Co-operative Coal Company who decided to mine for coal and named the mine &quot;Teralba Colliery.&quot; Shaft sinking was commenced in 1886 but was delayed by financial and water troubles to such an extent that it was not until 1901 that the Borehole Seam was reached.Coal was won until 1904 using a single 16 ft. diameter shaft, ventilation being achieved by means of a wooden boxing down one side of the shaft. This collapsed, and operations ceased until the mine was taken over in 1906 by a company known as &quot;Borehole Colliery Limited,&quot; the principal stockholder being the Stockton Coal Company. It renamed the mine &quot;Borehole Colliery.&quot; This new company immediately commenced sinking a 13 ft. diameter air shaft. In 1908 the Stocktol1 Colliery at Stockton was abandoned, and during the following year much of its equipment was transferred to Borehole Colliery. The name was again changed becoming &quot;Stockton Borehole Colliery.&quot; From this period on, coal was produced from the Borehole Seam by...

Jan 1, 1957

By Jill Murray

This study focuses on the amosite mining region in South Africa and associated health effects, compared to other mined asbestos fiber types. Historically, dust and fiber levels were high in the amosite mills and mines, and many miners and members of the surrounding communities were exposed to the fibers. Research has shown that amosite produces both benign and malignant disease. Nevertheless, the mesotheliomagenic potential of amosite is several fold lower than crocidolite. The risk of disease associated with amosite exposure is difficult to quantify. Reasons for this include the scarcity of available information, including fiber measurements, and case ascertainment, as well as the juxtaposition of the amosite and crocidolite asbestos seams in South Africa. © 2007 Elsevier Inc. All rights reserved. Keywords: Amosite; Mesothelioma; Crocidolite; South Africa; Asbestos

Jan 1, 2007

By Eric G. Kok

Complying with respirable dust standards is presently a critical problem for many longwall faces equipped with double drum shearers. Results are presented of research performed to increase the quantity and optimize the distribution of the water supplied to the shearer drums to control the shearer operator dust exposure. The effect on the total respirable dust produced by the shearer was also examined. During the research effort, a simple and inexpensive manually controlled valve system was designed and implemented on a shearer to distribute the water supplied to the shearer drums. Research showed that increases in water quantities are beneficial but associated pressure increases may induce respirable dust boilover negating potential advantages. Other essential parameters such as location of shearer operator, outside spray orientation and air quantity were considered in the evaluation.

Jan 1, 1986

The Canadian mining industry is one of the strongest in the world. Not only does the country produce a sizable amount of minerals and metals, Canada plays host to hundreds of global mining companies, large and small. The country, for the most part, recognizes the importance of natural resource development, particularly mining, to its economic well being. Like any country, though, there are federal and provincial regulations on the books that the industry takes issue with. But there are also certain economic incentive programs in place to encourage exploration and mine investment. And, unlike the industry and the United States government, the Canadian government and mining industry appear to have a reasonable working relationship.

Jan 4, 2010

By Jr .. Ebbley

The investigation of mine shafts and underground workings at Leadville, Colo., was started in May 1946 and recessed in November 3, 1946. Thirty-eight shafts and connecting accessible underground workings, comprising about a third of the accessible shafts in the district, were investigated. The Leadville district, a former important producer of lead and zinc, was considered by the Bureau of Mines to be capable of bolstering &apos;the waning domestic output of .these important metal. Accordingly, the investigation was initiated for the purpose of. .obtaining more definite data on sulfide and oxide reserves, evidence to justify completion of the Leadville drainage tunnel, representative large samples of the complex oxidized and mixed ores for testing to determine methods, beneficiation factual data to be supplied to property owners in order to stimulate production, and to determine the more favorable areas for development by the Bureau.

Jan 1, 1949

By Lars Richter, Franz-Werner Gerressen

"The Eglinton Crosstown Line was conceived as the Eglinton Crosstown LRT, a partially underground light rail line, announced in 2007 as part of the Transit City plan, which included the implementation of six other light rail lines across Toronto.There were 43 stops planned for the Eglinton Crosstown LRT, 13 of which would be underground . For those underground stations a lot of specialty foundation works needed to be carried out. King piles, soldier piles with lagging and secant piles were mainly required fulfilling the tasks of installing the retaining wall system.The paper will focus on the original design and alternative solutions, discussing the benefits and limits of these. It will also explain the installation process in general as well as some specific features related to specific site conditions, e.g. limits in installation depth, soil characteristics etc. The required equipment will be explained showing the benefits and limits.INTRODUCTIONThe Eglinton Crosstown project is a 19-kilometre LRT line that will bring much needed relief to the transit woes of Torontonians. Traversing the city in an east-west slice across the midtown artery of Eglinton Avenue, the Crosstown rail line involves a combination of 15 underground stations and 10 atgrade surface stops. It is one of the largest transit infrastructure projects under way in North America today. Aecon has joined partners ACS Infrastructure Canada, Ellis Don, and SNC-Lavalin to form Crosslinx Transit Solutions (Crosslinx).As with many of today’s mega public transportation projects, the Crosstown LRT follows the Public- Private Partnership (P3) model. Aecon is an equal partner in the $5.3-billion Crosslinx consortium to develop the Eglinton Crosstown LRT project in Toronto. Upon the LRT's completion in 2021, Metrolinx, the region’s transit authority and also the project client/owner, will turn to the Toronto Transit Commission (TTC) to operate it. The impact of this highly anticipated LRT line on commuters in the Greater Toronto Area (GTA) is expected to be dramatic and immediate once the first train leaves the station five years from now. In fact, Metrolinx is estimating that within its first 10 years of service, the Crosstown line will be carrying 5,500 passengers per hour (in peak direction) and making 100 million passenger trips annually."

Jan 1, 2017

By R. S. Dean

In general, the Division conducts investigations relating to the treatment of ores and metallurgical products from the condition to which they are mined to the refined metal. At the object of conserving natural resources and eliminating waste by furnishing information on current methods of metallurgical practice making fig fundamental studies of metallurgical processes and developing new processes and alloys to the point of demonstrating their or value. Office of the Chief Engineer The functions of the technical units of the Office of the Chief Engineer are indicates

Jan 1, 1941

By Peter Cunningham

General Description of Projects The objective is to streamline data transfer within our Process Control and Business Systems for the purposes of tracking actual production, reducing manual record keeping, improving process control and improving vehicle maintenance. This presentation focuses on two implementations of mobile equipment data acquisition systems which make use of industry standard data models and data transport protocols. Pilots are part of the Mines Technology Roadmap to improve our mining operations ?Enabling technologies and pilot of key systems

May 1, 2013