Search Documents

By Gabriel S. Esterhuizen

A survey of pillar conditions was carried out at 21 operating limestone mines that use the room-and-pillar method. The surveyed pillars were all located in rock that was classified as ?Good? to ?Very Good? using the RMR rock mass classification system. The average pillar width was 14.5m and the width to height ratio varied between 0.53 and 3.52. Pillar conditions were rated using a visual rating system that accounts for the effect of geological structures as well as stress related fracturing. Nine cases of pillar instability were recorded. Pillar instabilities were typically limited to individual pillars or small groups of pillars within an otherwise stable layout. Local geological structures such as inclined discontinuities or weak bedding planes contributed to instability in seven of nine cases that were observed. Elevated pillar stresses contributed to instability in the two remaining cases. All the unstable pillars observed had width-to-height ratios of less than 1.5. It is concluded that pillar instability is most likely to be caused by unfavorable geological structures in pillars with width to height ratios of less than 1.5. Stress related instability such as rib spalling becomes more prevalent when the average pillar stress approaches approximately 20 MPa.

Jan 1, 2006

By Peter Bourke, Marc van Olst, Seppo Ronkainen, Natalie Brown

"Since the early days of flotation, process technicians have known that the speed at which the froth is recovered over the lip of the cell has a very direct and consistent influence on the grade and recovery of the circuit. No plant would deny that, even to this day, one of the most important aspects of a process technician’s job is ensuring that the froth is moving at a desired and controlled speed over the lip. Unfortunately, process technicians cannot watch the froth throughout the entire shift, as there are always a lot of other tasks to do.A considerable amount of work has thus been done to develop a “system” that automatically measures the speed of the froth. This measurement would then be used in simple controllers to emulate the steps taken by the process technician in correcting deviations of the froth speed from its desired level. Many of the earlier attempts to measure speed were ineffective, as they were unable to cope with turbulence on the froth surface. The FrothMasterTM instrument makes use of machine vision technologies to measure the speed of the froth over the lip of a cell at a very high sampling rate. This instrument produces an extremely reliable and accurate measurement of the froth speed (as well as other parameters such as bubble size and froth stability). As we will show, the effectiveness of the speed measurement in controlling the performance of the plant is a testimony to its reliability.Three FrothMasterTM units have recently been installed on the Cadia Hills Gold Mine in New South Wales (Australia). The objectives of this installation were:To control the mass-recovery of two Tank Cells in series on the same level where differences in the hydrostatic head between the two cells result in the cells pulling inconsistently with respect to each other.Control of the concentrate grade (%Copper) from the first rougher.Reduction in the frother consumption in the rougher circuit by monitoring the froth speed.A simple controller was designed to react to disturbances in the same way that human operators react. This was done after consultation with the metallurgists and the process technicians at Cadia. The controller had two functions:Stabilisation: The stabilising controller made use of three manipulated variables (level, frother addition rate and aeration rate) to control the froth speed to a setpoint.Optimisation: The optimising controller adjusted the froth speed setpoint based on deviations of the grade (measured in real-time with an OSA) from a setpoint. The plant metallurgist adjusted the grade setpoint based on information about the ore."

Jan 1, 2001

By Paul C. Schmall

The link between artificial ground freezing and the mining industry stretches back more than 140 years, and across an ocean. Patented by the German scientist F.H. Poetsch in 1863, the technique is reported to have first been used circa 1862 in the coal mining valleys of South Wales. In the United States, the first ground freezing application, to a depth of 30 m (100 ft), occurred in 1888 for the Chapin Mine Co. in Iron Mountain, MO. In England in 1901, the Poetsch method was used for the first time to successfully sink two shafts through 24 to 27 m (80 to 90 ft) of wet sand and boulder clay at the Washington Glebe Colliery, near Sunderland. British mining engineer T.H. Cockin, in his 1905 Class-Book of Practical Coal-Mining, noted that, ?This method of sinking through thick beds of very wet quicksand has met with great success; it is one of the recognized methods of sinking on the Continent.? Mine shaft freezing soon became relatively common in Europe where the project could bear the cost of a major refrigeration plant construction. However, it was not until 1952 that the second North American ground freezing project was completed to facilitate the sinking of a 4.5-m- (15-ft-) diameter, 233-m- (765-ft-) deep shaft at a Potash Company of America (PCA) mine in Carlsbad, NM. Nowadays, ground freezing is used worldwide for both mining and civil applications. In small mine shafts of 3 to 6 m (10 to 20 ft) in diameter, excavations have been carried out to depths of more than 820 m (2,700 ft) within the protection of unbraced or unlined frozen walls. In fact, for deep mines, no better method has yet been established for sinking production shafts through deep, water-bearing ground. Major deposits of coal, potash and salt would still be inaccessible if not for artificial ground freezing. There are several advantages of ground freezing unique to the construction of shafts. Proper instrumentation can provide complete assurance of the integrity of the freeze to full depth prior to excavation. The frozen wall allows construction to be scheduled without evaluating the in-shaft time necessary to probe ahead, place additional sup-ports or deal with ground water. The freeze can be implemented perfectly through the soil/rock interface, which is often the most difficult geology in which to create a ground water cutoff by other methods. At increasing depths, any discontinuity

Jan 1, 2007

By B. J. Moore

This publication contains analyses and related source data for 269 natural gas samples from wells and pipelines in 18 States. All of the samples were obtained and analyzed during, calendar year 1979 as a part of Bureau of Mines investigations of the occurrences of helium in natural gases of countries with free market economies. This survey has been conducted in the United States by the Bureau of Mines since 1917. In late 1965, the survey was expanded to include foreign gasfields. The analyses published herein were made by mass spectrometer and a special helium analysis apparatus, which are described in Bureau of Mines Bulletins 4862 and 576.3 The results of the investigation of the occurrences of helium are published annually to make the information available as soon as possible to the gas industry and the general public. Twenty-one previous publications have presented tine results of 11,883 gas analyses made prior to 1979. The first three, Bulletins 486,4 576,5 and 617,6 contain analyses and related source

Jan 1, 1980

By Edwin E. Maust

In response to the ever- increasing demand for high temperature materials, the Bureau of Mines instituted a program for the study and development of superrefractories, One of the major tools obtained for use in this research was an image furnace of the double-paraboloidal mirror type. Although extensive theoretical analyses of solar furnace performance may be found in the literature, comparable detailed information on the double-paraboloidal-mirror image furnace has been nonexistent. This report presents an analysis based on an investigation undertaken to ascertain the limitations and characteristics of the furnace so that it can be used most effectively. The quantitative determination of the energy available at the image, the control of this energy by mans of a 60-inch iris diaphragm, and its variation with position and time relative to the heat source used have all been dealt with in detail. The quantitative results were obtained using a specially designed waterflow calorimeter and these measurements, in conjunction with the theoretical analysis, are used to present a fairly complete description of the furnace and its capabilities.

Jan 1, 1962

By Y. P. Chugh, J. Ma

Higher production, better safety standard, and potential for automation are some of the benefits of longwall mining. Today, longwall face advances at a faster rate exposing many diversified rock layers in a short period of time. It is now a serious challenge to cope with ground control problems such as roof falls, face and floor failure, and excessive shield loading as fast as possible to minimize production and monetary losses. In Illinois coal mines, the existence of weak floor strata blow the coal seam may pose additional problems related to floor heaving, shield base punching, and associated roof and face falls. In this study, the effects of weak floor on longwall ground control are analyzed using two-dimensional finite element models. A two-leg 635.6-ton (700-short-ton) yielding capacity shield is included in the models to evaluate the effects of different thickness and material properties of the weak floor. The study indicates that the thickness and material properties of weak floor have significant effects on shield loading, the distribution and intensity of front abutment stress, failure zones in the surrounding strata, roof-to-floor convergence, and floor punching by the shield base.

Jan 1, 2000

By Claudio Olalla

This paper relates to the foundation of a steel structure located at the San Martin de la Vega (Madrid) amusement park. The structure has more than 100 supports with various loading conditions, including important horizontal and uplift forces. Additionally, the settlement tolerances are very strict. A massive gypsum formation with interbedded clay layers and random solution great voids at various levels constitute the soil. The foundation design has been conditioned large enough these difficulties (load conditions and soil problems). The piling machine used was powerful to drill through the soft rock (UCS up to 11Mpa). The integrity of each pile had to be guaranteed by continuous recording of drilling and concrete pouring parameters. In order to fulfil all those conditions, a STARSOL type-piling rig was used. More than 4500 meters of piles were performed. The diameters of the piles were 450 and 550-mm and their depths varies from 6 to 23 meters. All piles were reinforced over their full length.

Jan 1, 2002

By M. Deutsch, E. González, M. Williams

"Uncertainty exists in ultimate-pit limits due to geologic variation and unpredictable economic landscapes. In this work, we show how this uncertainty affects the ultimate pit and how it can be analyzed to improve the mine planning process. A stochastic framework using geostatistical simulation and parametric analysis was used to model the effects of geologic and economic variations on ultimate-pit limits and overall project economics. This analysis was made possible by a new pit optimization implementation that can be automated and set up to calculate ultimate pits for hundreds of different scenarios in a matter of hours. Quantifying ultimate-pit uncertainty early in the mine planning process allows mining engineers to make informed decisions regarding infrastructure placement and to mitigate the possibility of incurring substantial costs to relocate critical mine facilities. Resumen ¦ Existen dudas sobre los límites del pit final por causa de la variación geológica y lo impredecible de los paisajes económicos. En este trabajo les mostramos como esta incertidumbre afecta el pit final y como puede ser analizada para mejorar el proceso de planificación de la mina. Se usó un marco estocástico con simulación geoestadística de análisis paramétrico con el fin de poder hace la modelación de los efectos de las variaciones geológicas y económicas en los límites de pit finales y proyectos económicos en general. Este análisis fue posible gracias a una nueva implementación de optimización de pits que puede ser automatizada y configurada para calcular pits finales para cientos de escenarios diferentes en cuestión de horas. La cuantificación temprana de la falta de certeza en pits finales durante el proceso de planificación permite a los ingenieros de minas tomar decisiones informadas en lo que respecta a la ubicación de infraestructura y en la mitigación de posibles costos sustanciales por causa de la reubicación de instalaciones clave de la mina."

Jan 1, 2015

According to the data provided by the most recent European Survey on Working Conditions, roughly 25 per cent of the European working population is exposed to mechanical vibrations for no less than one quarter of the work shift duration, while around ten per cent are exposed for the entire work shift. The occupational exposure to whole-body vibration (WBV), in particular, represents a major health risk in mining, quarrying and civil excavation activities. In accordance with European Directive 2002/44/EC, the latest version of the Italian law on physical risks has recently confirmed the possibility of using relevant literature data on vibration magnitude in order to evaluate personal occupational exposure (vibration database or data provided by the manufacturer). Still the alternative option, based on field measurements, represents the most appropriated method of risk assessment, as it accounts for the actual operating condition at the workplace; actual operator and vehicle under investigation and specific working cycle. The article discusses the vibration measurements taken on a number of heavy machinery (excavators, loaders, trucks, dumpers, etc) employed for talc extraction in a mine located in Sardinia and the resulting personal exposure for the drivers. The assessment was carried out in accordance with the specifications of ISO 2631-1 and EN 14253.

Dec 6, 2010

By P Moswate, D Phillpotts, S M. Mantsho, P Strobos

A challenge on many industrial flotation circuits is controlling concentrate mineral grades using measurements that are provided infrequently. The mineral grades in concentrate streams are a critical performance indicator in any industrial flotation circuit. Failure to achieve concentrate mineral grade targets has significant financial consequences on a flotation operation. A violation of gangue mineral grade limits by the concentrator may also result in significant penalties.Online grade analysers which can provide reliable real time grade measurements are essential for effective grade optimisation. The Blue Cube MQi analyser (by Blue Cube Systems) has recently come to prominence for its ability to rapidly determine mineral concentrate grades online and has the benefit of operating in-stream. This has provided excellent insight into the actual process dynamics in the flotation circuit, and hence enabled real-time control and optimisation of concentrate mineral grades.MintekÆs Measurement and Control division, specialising in advanced control solutions for mineral and metallurgical industries, has had the opportunity to link the FloatStar Grade-Recovery Optimiser to the measurements provided by the Blue Cube system at the BCL nickel concentrator plant in Botswana. The project focused on stabilising the final concentrate grade while ensuring the final tailings are minimised, resulting in an improved nickel recovery. This site already had the FloatStar Grade-Recovery Optimiser for several years, but the original grade measurement device was unreliable and ultimately failed. The system was reactivated once the Blue Cube system was installed, replacing the old analyser. The positive results show the advantages of combining reliable real time measurements with an advanced process control system.CITATION:Mantsho, S M, Moswate, P, Strobos, P and Phillpotts, D, 2013. The implementation of floatstar grade-recovery optimisation control solutions using Blue Cube Online grade analysers on industrial flotation circuits, in Proceedings MetPlant 2013 , pp 575-582 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By Patrick J. Hannigan, Geir Veslegard, Frank Rausche, Rozbeh B. Moghaddam

A common type of deep foundation used in Norway to support bridge structures is the drilled pipe piles (piles) filled with concrete reinforcement after installation. The standard installation practice is the use of down-hole hammers. Complex geology and difficult subsoil conditions in Norway causes a high variability of soil and rock layers which in turn make for differences between actual subsurface conditions and those expected from geotechnical exploratory borings. This situation is strongly noted when the foundations are not fully socketed, and the rock layer is sloped. In this particular case, special testing procedures are required to assess the drilled pile base material and evaluate the rock-socket to ensure full contact between the foundation base and the rock surface. The local standard practice to verify the latter condition, consists of coring and visually evaluating the material recovered at the bottom of the drilled pile. This paper presents a case where the coring and visual inspection were not possible and alternatively the geological material encountered at the base of the deep foundations was evaluated using force-displacement measurements. Two 1016-mm (40in) diameter open-end drilled piles identified as P02-04 and P02-05 were tested and evaluated using in-situ force-displacement data prior to filling the piles with concrete. Test results showed an average displacement of 7mm (0.28in) corresponding to 35MPa (5.1ksi) stress level for P02-04, and 7.2mm (0.28in) corresponding to a stress level of 38MPa (5.5ksi). Based on testing results, both drilled piles were within the established material assessment criterion presented by the local authorities. INTRODUCTION This paper presents a case study in Norway where the material encountered at the base of an open- end drilled pipe pile (pile) was evaluated using force-displacement data. In the deep foundation industry in Norway, it is a common practice to install piles to support transportation structures. Once the piles reach the embedment elevation, and the pile base is assessed, these are filled with concrete. In projects where sloping rock is the supporting layer, and all nominal loads are supported by the pile base resistance, assessing the material encountered at the pile base to ensure full contact with the rock becomes critical. The local practice to make this assessment consists of the use of weighted tape, coring, or inspection cameras. However, similar to any other testing and evaluation methods, these come with their own limitations. The variability associated with the use of the weighted tape, accessibility for the coring equipment to complete a coring process, or the conditions at the foundation base such as murky water or thick drilling fluids could significantly impact the photo or video quality taken at the pile base. In such conditions, it is important to consider alternate testing methods to evaluate the material at the foundation base.

Jan 1, 2018

By E. C. Lane

[This is the tenth in a series of retorts on properties of commercial motor fuels, made in accordance with a cooperative agreement between the Cooperative Fuel Research (C.F.R.) Committee e end the Bureau of Mines of the United States Department of the Interior. The first report rave data on motor gasolines sold during .e winter of 1935-36.3/ The present report presents analytical data for 1,732 samples, representing the products of approximately 50 companies, which, as in previous surveys, include both lame and stall suppliers. In addition, the Pacific coast is represented by data that were averaged by the Pacific Coast Technical Group before being submitted and are published exactly as they were received. As in previous surveys, the data are divided into the three groups of samples of regular-price, premium-price, and third-grade gasolines, and each group has been averaged separately. he number of samples, items, and brands comprising each groan), exclusive of those of the Pacific coast, are as follows: Regular price, 934 samples, 230 items, and 50 brands; premium price, 465 saris samples, 184 items, 40 brands; third-grade gasolines, 360 samples, 177 items, and of these terms as used in the surveys are follows: Sample: The individual supply of gasoline obtained at the filling station and analyzed in the laboratory.]

Jan 1, 1941

By C. J. Kirkland

For two thousand years and more, we insular Britons have been grateful for the existence of the narrow strip of water that separates us from mainland Europe. It has given us a sense of security against invaders, though it has been breached many times. The first recorded serious consideration of a fixed crossing of the English Channel was in around 1802, when it was suggested to Napoleon I. The motive was not entirely peaceable and the British Navy, who saw themselves as defenders of our shores, were decidedly unenthusiastic A whole series of imaginative schemes were proposed in the course of the nineteenth century, embracing viaducts, immersed tubes, artificial islands as resting places for the horses which were to draw carriages, as well as mechanically bored tunnels. The first Channel Tunnel Company was formed in 1872, and an application for permission to construct a tunnel was made to the British parliament. A Colonel Beaumont, of the Corps of Royal Engineers designed and constructed a machine which, in around 1882, bored over a mile of tunnel out to sea from Britain which exists to this day.

Jan 1, 1991

By A Hanna

Quarries around Auckland have reached or are reaching the ends of their lives, which raises issues about rehabilitation. Significant volumes of 'cleanfill' are generated by the City, particularly during phases of urban renewal and development. Emplacement of the fill in quarries removes the problem of fill disposal and provides an opportunity for restoration of the quarry site.There is a compatibility between quarrying and cleanfilling because at quarries:Truck routes are already established Neighbours are accustomed to the effects and appropriate buffer distances have been established Bringing fill into a site attracts aggregate sales and is very efficient. Fill originates from construction sites and ad-hoc excavations and therefore it is not surprising that sampling has shown the quality to be variable. Both Winstone and the Auckland Regional Council have surveyed undisturbed soils in the region to attempt to determine natural background levels of common contaminant substances. Comparison of these levels with delivered fill shows that a high proportion of delivered materials can be regarded as mildly contaminated. Therefore the term 'cleanfill' is, in the Auckland region at least, a misnomer and the term 'managed fill' has been adopted.Historically and presently the only control on quality of 'cleanfill' has been some visual inspection. This leaves the fill operator open to potential liability for creating a contaminated site. Implementation of controls at WinstoneÆs operations has progressed slowly, over some ten years. This is mainly due to the perception that mobility of contaminants within and out of the landfill will be very limited because of the near-neutral pH and abundance of clay minerals in the fill. The methods of control and results of environmental risk assessments at WinstoneÆs Puketutu Island Quarry will be briefly described.

Jan 1, 2002

By Christine Hansen

?Kiss my Asteroid? Unofficial Title Human life is tied to minerals It?s worth noting that: The living human body consumes minerals. The minerals we take in multivitamins show the close linkage between human beings and mineral resources. Unlike tourism or specialized manufacturing, a human being could not live without mineral consumption. Minerals and their consumption is a tangible part of human life.

May 1, 2013

By Richard D. Hagni

The character of phosphorous-bearing minerals in the Birmingham red Iron ores and iron-bearing minerals in the Eufaula bauxite deposits in Alabama has been Intensively studied by petrographic, ore microscopic, luminescent microscopic, scanning electron microscopic, electron microprobe, and x-ray diffraction techniques. A total of 15 types of phosphorous-bearing mineral grains have been recognized in Birmingham iron ores by their characteristic sizes, shapes, and distributions. Size measurements, modal analyses, and texture analyses have permitted an estimate of potential liberation of phosphorous from the iron ores by beneficiation to be 27% In areas of previous mining and 60% in areas of current iron reserves. Fine grinding, selective flocculation, and flotation may constitute the best beneficiation technique for future research. Hematite and goethite are the most important iron minerals in Eufaula ferruginous bauxites, but pyrite, marcasite, and siderite are Important iron minerals in some varieties of ferruginous bauxite, and lepidocrocite and ilmenite occur locally in minor quantities. Although simple screening will remove the coarsest iron-bearing grains, research on the utilization of high gradient magnetic separation to reduce the amounts of iron-bearing grains is recommended.

Jan 1, 1981

Wetting Characteristics of Mineral Surfaces - Contact Angle Measurements through Molecular Dynamics Simulations

Sep 13, 2010

By L. A. Neumeier

The Bureau of Mines evaluated creep properties of Zn-Cu-Ti alloys that were annealed after finish-rolling either cold) or at 480° F (249° C). Compositions ranged up to 1.25 pct Cu and 0.36 pct Ti. Most data are for sheet annealed after finish-rolling to 92-pct total reduction. Annealing times were varied at temperatures between 320° and 560° F (160° and 293° C). For a number of the alloys, annealing after hot-rolling at 480° F affects creep properties very differently in longitudinal and transverse sheet directions. The detrimental result is that the anisotropy in creep properties between the two directions can be vastly increased. Conversely, specific annealing treatments of certain heavily cold-rolled alloys result in surprisingly low anisotropy in creep properties and the low anisotropy coincides with excellent creep resistance for both directions. Supplemental data are presented on tensile, hardness, and thermal expansion properties, and microstructures.

Jan 1, 1972

By R. E. Zane

The Northwest Experiment Station of the Bureau of :,!in-s, in cooperation with the College of Mines, University of Washington, has completed a detailed investigation-of the physical and chemical properties of western cokes made or used in the Pacific Northwest, as evaluated by standard methods./ One of the properties determined, to which more or less importance has been attached, was reactivity5/ or combustibility. As no standardized procedure is available, it was necessary to develop a workable method for evaluating this property. The combustibility of coke is usually measured by the formation of carbon dioxide with time at a particular temperature or by the reduction of carbon dioxide to carbon monoxide. Analysis of the resulting gases commonly is required to evaluate the result. The method described in this paper is simple and direct in that the sample of coke or other carbonaceous material is weighed as it burns; the loss in weight and time is indicated by a balance and clock arrangement. Gas analyses are not required. Methods similar in principle have been used by Tu, Davis, and Hottel6/ and by Oshima and Fukuda7/ for determining the combustion rate of carbon and for studying the effect of ash on combustion characteristics. Both methods are more elaborate in procedure and apparatus required than that described here. Briefly, the method comprises burning a sample of coarsely grained coke or

Jan 1, 1940

By Grant R. Brown

The report provides guidance for determining those environmental impacts associated with the surface mining of steeply pitching coal seams. In addition to the environmental impacts, four additional issues are addressed, namely (1) Time and motion studies of those coal mining systems employed in mining seams which pitch in excess of 25°, (2) Assessment of those mining techniques, (3) Development of rationale for the mining methods employed, (4) Identification of the reclamation practices and determine whether these practices were in compliance with appropriate Federal and State regulations. Five surface mines located in three geologically distinct basins of the United States were analyzed during the period of August through November 1979. The three basins include the Hanna Basin of Wyoming, the North Park Basin of Colorado and the Southern Anthracite Field of Pennsylvania.

Jan 1, 1980