Search Documents

By Chris Uys, Johan Labuschagne

Sishen Iron Ore Mine, located in the Northern Cape, is an open cast mine excavating approximately 100 million tons rock to produce 25 million tons of high grade haematite ore per annum. The size of the pit is approximately 12 km ‘1.5 km ‘150 metres. The final depth is planned to be around 350 metres. It is hard rock mining operation employing the conventional truck and shovel method. Mining benches are twelve and a half metres in height and are divided into blasting blocks, each consisting of approximately 300 000 tons of material.

Jan 1, 1997

By Carl Heinrich

I HAVE read with particular interest that portion of the discussion by Anton Eilers referring to the high-lime (and also high-alumina) slags made by August Raht in 1881, while smelting the Horn Silver ores at Franklin, Utah. The two analyses of such slags, furnished by Mr. Raht to Mr. Eilers are: Horn Silver Slags Oxygen(b) Oxygen(b) Average of I and. II Slag I percentage Slag II percentage Oxygen Si02 33.9 18.1 .35.0 18.7 34.50 18.40 FeO 26.8 6.0 25.4 5.7 26.10 5.80 CaO 26.1 7.5 24.9 7.1 25.50 7.30 BaO 3.2 (a) 0.3 3.2 0.3 3.20 0.30 A1203 10.8 5.1 9.3 4.4. 10.05 4.75 100.8 37.0 97.8 36.2

Jan 10, 1916

By H. Stanley Benson

This report is an account of research conducted to improve the performance of and then further field test Draft Power Sensor (DPS) equipment, the use of which enables a bulldozer operator to optimize his machine's work rate. Significant improvements were made in DPS hardware, and extended field testing was conducted at two working strip mines: the Glenharold Mine of Consolidation Coal Company, near Stanton, North Dakota, and the Beulah Mine of Knife River Coal Company, near Beulah, North Dakota. This report documents the increase of bulldozer work production by greater than twenty percent while using the Draft Power Sensor when compared to baseline work production without benefit of the Draft Power Sensor. Research was done by Southwest Research Institute under contract with the Bureau of Mines.

Jan 1, 1980

By W. J. González

"With the increasing demand for minerals, technologies to maximize mineral recovery are paramount to a mine’s economic success. Many mining process waters have the potential to form calcium-based inorganic scales, which inhibit effective mineral recovery. Often, the solution to inhibit these deposits is the implementation of a chemical antiscalant program. This paper examines the application of a fouling analyzer to continuously monitor the formation of inorganic scale in mining process streams. The fouling data can be used to compare antiscalant programs and to optimize antiscalant feedrates. Case studies validate the ability of this technology to help optimize mineral recovery processes.INTRODUCTION The mining industry uses significant quantities of water. From quarrying, to crushing, to flotation, leaching, and refining, water is often the integral motive force to move slurries, separate or agglomerate fines, and extract and purify minerals. As well, water is used in a number of ancillary applications at mines, including dust suppression, gas scrubbing, and utility processes such as boiler, cooling, and waste water operations. For many processes, the quality of water being used is inconsequential. However, for certain processes, such as flotation, leaching, and desorption / stripping, water quality plays a key role in the ability of the operation to economically recover the target minerals. Dissolved solids such as calcium and magnesium salts can concentrate in process waters, exceed their solubility limits, and precipitate as scale on metal surfaces such as feed and transfer pumps, piping, and equipment. Some of the more common scales that form in mining operations include calcium carbonate (CaCO3, or calcite) and calcium sulfate (CaSO4, or gypsum), and to a lesser extent, calcium and magnesium silicate compounds. Any scale that deposits in a process stream will negatively impact mineral recovery, and increase the operational costs of the mine site. Whether it is acid washing a scaled heat exchanger in a carbon strip at a gold operation, replacing plugged emitter tubes in a leaching operation, or hydroblasting process lines in a scrubber unit, there are costs associated with labor, cleaning chemicals, repairs, and replacement parts. These costs pale in comparison to the potential costs of downtime and lost production, should the scale deposits occur in a process that is critical to the recovery of the target mineral."

Jan 1, 2014

By Thornton L. Neathery

Geologic investigation of a mineralized zone in eastern Alabama indicates that large quantities of talc and soapstone are scattered over a wide area close to the surface. Laboratory experiments show that this material may be upgraded to a high-quality talc. A market survey indicates that the talc deposits may be of current and long-range interest. The anthophyllite asbestos which is associated with the talc does not appear to occur in sufficient quantities to be considered as a primary commercial source.

Jan 1, 1967

By R. Patel, D. R. Taylor, P. M. Varley

In-situ measurements of ground stress were made from surface boreholes, using overcoring and hydrofracturing techniques, to obtain data for the detailed design of the underground works at Pergau. Unexpectedly low stresses were measured and appeared to correlate with apparent hydrofracturing observed during permeability testing. The low values of the minor principal stress had a major impact on design, particularly of the lining for the pressure tunnel and shaft. Additional hydrofracture tests were made underground during construction of the low- and high-pressure headrace tunnels and the pressure shaft, to define the vertical reduction in the minor principal stress with overburden. These data were then used to locate and design the steel and reinforced concrete linings

Jun 19, 1905

By H. K. Lin

Residual cyanide in cyanidation tailings can be detoxified by its oxidation to cyanate, as in the Inco and Degussa processes. However, cyanate, the product of detoxification and other oxidation processes, may be reduced to cyanide in reducing environments, e.g., deepwater discharge of cyanidation tailings. This study shows that the reduc-tion of cyanate to cyanide occurs and that the reduction rate increases with decreasing solution redox potential. Solutions with lower pH favor the reduction rate. No significant difference was observed between the results of tests prepared with distilled water and seawater, and the presence of cyanidation solid tailings does not show an effect on the reduction. Because cyanate can be reduced to toxic cyanide, causing environmental concerns, the deepwater discharges of cyanidation tailings must be handled carefully.

Jan 1, 2008

By LaMar G. Evans

The rapid determination of uranium in ores by radiometric means was investigated by the Bureau of Mines. Among the various procedures and schemes tested, two showed most promise. They were the ratio scheme developed in the Bureau's Tucson, Ariz., laboratory and the equilibrium method developed by the Canadian Department of Mines and Technical Surveys. The ratio method is a simple, empirical procedure for classifying the state of equilibrium in ores by measuring their radioactivity by means of a Geiger-Muller counter under three different conditions, using filters. The principal merit of the method is in providing a clue as to the reliability of equivalent uranium determinations.

Jan 1, 1958

By Rob Thomas

Adequate load transfer is considered essential for optimum ground support and is increasingly important in weak roof and/or high stress environments. If adequate load transfer is achieved not only can this have a positive impact on the resulting roof behavior, but it may also allow the use of lower and hence more economic densities of roof support. A wide variety of post-groutable cable bolts are currently in use in the Australian coal mining industry, each of varying capacity, design, and grouting methodology. Though all of the cables are supplied with the appropriate steel specification, strength, and modulus data, the Australian coal mining industry does not have access to a comprehensive and comparative database on the corresponding load transfer performance, which is a critical problem. On the basis of the above, this paper describes the methodology and results of a laboratory pull testing program that aims to assess the impact of cable bolt design on load transfer, and specifically, the impact on the capacity and stiffness of the anchorage. As part of the testing program, 19 cables were tested including (1) plain-strand cables installed in holes drilled with 28 to 55 mm diameter drill bits and (2) bulbed and nutcaged cables installed in holes drilled with 42 to 64 mm diameter drill bits. Other parameters assessed included the significance of smooth and profiled wire, wire packing, and expanded geometry bulbs. The main results of the testing indicate that in comparison to plain-strand cables, if the cable is bulbed or nutcaged, the capacity of the anchor can increase by up to 400%, and the peak stiffness by between one and two orders of magnitude. The results also indicate that increasing hole diameter may have a positive impact on load transfer in the case of bulbed or nutcaged cables and a negative impact on plain-strand cables. No conclusive results were obtained with regard to the impact of grout strength on load transfer.

Jan 1, 2012

By B. S. Van Gosen

In recent years, U.S. regulatory agencies have placed emphasis on identifying and regulating asbestos dust exposures in the mining environment, with a particular focus upon industrial mineral deposits in which asbestos occurs as an accessory mineral. Because asbestos minerals form in specific geologic environments, only certain predictable types of industrial mineral deposits can potentially host asbestos mineralization. By applying a basic knowledge of asbestos geology, the costly and time consuming efforts of asbestos monitoring and analyses can be directed towards those mineral deposit types most likely to contain asbestos mineralogy, while saving efforts on the mineral deposits that are unlikely to contain asbestos. While the vast majority of industrial mineral deposits in the Western United States are asbestos-free, there are several types that can, in some instances, host asbestos mineralization, or be closely associated with it. These industrial mineral deposits include a few types of aggregate, dimension, and decorative stone, and some deposits of chromite-nickel, magnesite, nepheline syenite, olivine, rare earth elements, talc, vermiculite, and wollastonite.

Jan 1, 2009

By Qingwei Wang

This study focused on acidic wastewater from producing sulfuric acid system in zinc smelter containing mercury 21.48mg/L, zinc 55.85mg/L, lead 38.50mg/L, copper 1.68mg/L, cadmium 10.25mg/L, As 29.86mg/L treated by biologics. The factors of pH value, the ratio of biologics to mercury, complexing time, hydrolytic time and temperature were studied in this paper. Experimental results indicated that at pH value 10, quantity of biologics to mercury ratio was 16, complexing time 30min, hydrolyzation time 20min, temperature at 40?, concentration of mercury in treated water was removed to 22.15µg/L. At same time heavy metals such as Zn, Pb, Cu, Cd, As was removed by biologics, the remained concentration in treated water was Zn 0.53mg/L, Pb 0.12mg/L, Cu 0.01mg/L, Cd low to 0.01mg/L and As 0.023mg/L. According to EDAX analysis, mercury content in complexing sediment reached 28.49% easily to recycle as raw material and low concentration of heavy metals in hydrolytic sediment easily to dispose and treat.

Jan 1, 2009

By J. A. Theron

"This paper provides guidelines on performing mass and energy balance modelling involving coal and coal derivatives. Usually, the inputs to a pyrometallurgical process would be specified in terms of elements and compounds. Reliable thermochemical data is more widely available for species involving uniquely defined, relatively smaller molecules. However, in the case of coal, the molecules are extremely large and not uniquely defined. Consequently, modelling processes involving coal and its derivatives involve several potential pitfalls. These are outlined in the present paper.It was found that coal proximate analysis should not be regarded as absolute; it could vary with several parameters, including heating rate. For modelling, the use of ultimate analyses should be considered a preferable option to proximate analyses, where ‘fixed carbon’ and ‘volatiles’ are not defined in terms of chemical composition. Significant errors could be incurred if the larger molecules are neglected during calculation of the calorific value (CV) of coal gas (the gas liberated when coal is heated in the absence of oxygen).For elemental analysis determination, the oxygen content (which is calculated by balance) should be checked to ensure it is within the expected range. For representation of sulphur in coal, one should avoid doublecounting due to SO3 in the ash analysis.Potentially, oxygen in coal could be represented as O2, H2O, CO, or CO2.However, use of some of these species without considering the experimentally determined gross CV leads to significant errors in the energy balance. If coal enthalpy is calculated from elemental analyses without correction, representation of coal oxygen as H2O(l) gives reasonable accuracy. Coal volatiles could be represented by a complex mixture of compounds, even using different oxygen-containing species than these four, provided the enthalpy is corrected.It is recommended that an ‘enthalpy correction value’ be incorporated in energy balances involving combustion, devolatilization, or conversion of coal and coal derivatives, e.g. coke, char, or tar. That would imply that proximate analysis, elemental analysis, as well as the gross CV would be required for all solid or liquid coal-derived substances being modelled. No other correction due to carbon being present in a form other than graphite should be used, as that would imply double-counting some effects."

Jan 1, 2015

By R. D. Dukimo, M. V. Sevian

The nature of fracture and factors that control the extent of fracture in the tumble-drum and drop-tower tests have been identified. The product-size distribution, on which the standard strength indices for these tests are based, and the breakage rate constants depend on a number of factors other than the strength of the lumps. The standard indices and rate constants are meaningful only in a comparative context and for events whose loading mechanism is similar. The results of experiments on three Australian ores, from Yandi, Koolan and Mount Whaleback, are used in combination with fracture mechanics theory to explain why different tumble-drum standards have been found to be fully consistent. A more meaningful measure of strength could be the parameters of the Weibull function, scatter and average strength

Jun 19, 1905

By R. A. Jankowski

The U.S. Bureau of Mines (USBM) conducted a series of laboratory tests to investigate the effectiveness of using a flooded-bed scrubber with exhaust ventilation in deep-cut faces of up to 12.2 m in length. An experimental test program to determine the impact on respirable dust levels resulting from changes in face airflow, curtain setback distance, operator positioning, and operating parameters of the external spray system on the miner was completed. Gravimetric sampling was conducted in the immediate return and at three sampling locations on the off-curtain side of the entry. Statistically significant differences in dust levels on the order of 0.5 to 1.2 mg/m3 were observed between specific sampling locations and changes in several test parameters. Dust sampling results indicated that a flooded-bed scrubber and exhaust ventilation can be a viable dust control system for extracting deep cuts up to 12.2 m in length. The impact on methane was not evaluated.

Feb 24, 1997

This report presents the results of a study of mill tailings disposal practices and potential tailings dam stability problems. Recognizing the long period of time that would be required to develop the technology and practices necessary to significantly improve refuse disposal safety, the Bureau initiated this research effort as a first step in that development. Volume 1 includes a summary of conclusions and recommendations resulting from the overall research effort; discussions of disposal systems and methods, geology, seismicity, hydrology, and materials characteristics; evaluations of investigational techniques; discussions of usable interim generalized investigational, analytical and inspection procedures; discussion of general principles and presentation of a tailings technology manual outline; and discussion of needed future research am recommended programs.

Jan 1, 1974

By P Hunger, H Günter, F Heinicke

High pressure grinding rolls (HPGR) have been used for more than 20 years to grind iron ore pellet feed. Besides coarse comminution (crushing), where HPGR are installed upstream of the ball mill, there are numerous flow sheets where HPGR are used after ball milling and dewatering for re- or finish grinding.There is a clear growing interest in grinding of pellet feed with HPGR during the last few years. In addition to their known advantages of low specific energy consumption, high availability, low steel consumption and improved pelletising processes the lower environmental load (reduced or no water consumption) became a strong driving factor for the application of HPGR in pellet feed grinding.This growing demand increases the interest in better understanding of the HPGR grinding process with fine iron ore concentrates. One of the most important process parameters is the moisture content of the feed material which influences the performance of the HPGR enormously. The HPGR can react to fluctuations of the fresh feed properties to a certain degree by adjusting grinding force and roller speed. Nevertheless, there are limitations by the physics of the compression process and the capability of water absorption by the concentrate. The capability varies for different concentrates and different specific surface areas. This fact has to be considered during engineering of the beneficiation plant.The paper focuses on the influence of feed moisture content on the HPGR performance in view of throughput, increase of Blaine number and process stability on the basis of numerous pilot plant tests, modelling results and industrial experiences.CITATION:Heinicke, F, Günter, H and Hunger, P, 2017. Influence of feed moisture on high pressure grinding roll pellet feed grinding, in Proceedings Iron Ore 2017, pp 187–194 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Gary R. Peterson

In order to determine the potential availability of alumina to feed U.S. aluminum smellers, the Bureau of Mines evaluated 39 domestic mines and deposits of bauxite, alunite, and high-alumina clays and found that substantial increases in alumina prices would be necessary before nonbauxitic deposits could become competitive with bauxite. As part of the study, a price-tonnage relationship was developed indicating the quantity of alumina that could be produced from known deposits at various alumina prices and at a 15-pct discounted cash flow rate of return on the required capital investment. All capital and operating costs were calculated in August 1980 dollars. The domestic bauxite reserve base comprises three operating bauxite mines in Arkansas containing some 15.6 million metric tons of recoverable alumina (A1203). Ferruginous bauxites, clays, and alunites fall into the subeconomic category of identified aluminum resources, which, at the demonstrated level, contain over 4,000 million metric tons of alumina that are estimated to be recoverable. Analyses indicate that, at the demonstrated resource level, a total of some 15.6 million metric tons of alumina, all from three active Arkansas bauxite mines, is recoverable at a 1980 price of $0.12 per pound ($264 per metric ton) of alumina. A price of approximately $0.26 per pound ($573 per metric ton) of alumina would be required for production of the total U.S. resource. Thus, unless new technological breakthroughs occur that could make alternate sources of alumina competitive with bauxite, U.S. dependence upon imported bauxite will continue to increase.

Jan 1, 1981

As part of the Bureau of Mines program to reduce U.S. reliance on foreign suppliers of strategic and critical metals, research was conducted to improve technology for the recovery of critical metals from hardface alloy grinding waste, a form of superalloy scrap. This report describes a hydrometallurgical process that demonstrated on a laboratory scale that 79 pct of the chromium, 97 pct of the cobalt, 99 pct of the manganese, 99 pct of the nickel, and 90 pct of the tungsten could be recovered in chemical form from hardface alloy grinding waste. The process involved deoiling the grinding waste, followed by chloride-based dissolution of the deoiled material. A high-grade calcium tungstate (CaW04) product was recovered from the resultant leach residue by caustic leaching and precipitation. Iron, cobalt, man-ganese, and nickel chlorides were sequentially recovered from the leach liquor by solvent extraction. Amine extractants were used to extract the iron, cobalt, and manganese; decanal oxime was used to extract the nickel. Market-grade cobalt chloride (CoCI2), manganese chloride (MnC12), and nickel chloride (NiCl2) products could be produced directly from the resultant strip liquors. The final raffrnate was a relatively pure chromic chloride (CrCI3) solution that compared favorably with commercial solutions.

Jan 1, 1988

Geologists in some underground gold mines collect grab samples from broken ore piles or trucks as a method of grade control. It is often known as muck sampling. Generally, the goal of grab sampling is to try and reconcile the mined grade at the ore source to the predicted grade and/or predict the mill feed grade. The mass of the sample collected is limited by health and safety issues, as well as by the capacity of the laboratory to process the samples within a given time frame. In general terms, grab sampling is known to be problematic because samplers tend to oversample the fines, and/or pick out high-grade fragments; surface sampling of piles does not test material within the pile; muck piles in development drives/faces are likely to be zoned due to the blasting sequence; high or low-grade material may preferentially segregate in the pile during mucking; the five per cent mass reject size of the material in muck piles is very large from underground blasting; some correlation usually exists whereby the larger fragments are enriched or depleted in the critical component of value; and the average error made in estimating the true stockpile grade is likely to be high. The method is prone to chronic fundamental sampling, grouping and segregation, delimitation, and extraction errors. Substantial warnings must be given about the use of grab sampling for grade control in gold mines. The method may appear to work sometimes, which can be attributed to a fine gold particle sizing and more disseminated distribution. As with all sampling methods, its appropriateness must be determined by ore characterization and heterogeneity testing to ensure the method suits the ore type.

Jan 1, 2010

By W. K. Coughlan

The Wabana deposit of Dosco Industries Limited is situated on the east coast of Newfoundland, at Bell Island in Conception Bay. It is a Clinton-type iron-formation of Lower Ordovician age. Five separate beds have been recognized, with others noted locally. Economic production has been obtained from the Lower, Middle and Upper beds, which are second, third and fifth in sequence, al-though at present only the Lower Bed is worked. The potential area of occurrence is about 70 square miles. It i;; bounded by major faults to the north, east and west and truncated by erosion at the south, where rocks of the de-posit crop out on the north side of the island. The iron is contained in oolitic hematite and chamosite, with minor siderite. As the deposit is submarine, conventional exploration methods are not applicable and much interpretation and projection from mined areas is necessary to guide exploration and development. With the interpretation of information from existing mined ores, it is possible, using a minimum of diamond drilling in advance of working faces, to maintain adequate ore reserves.

Jan 1, 1966