Search Documents

By John Nunes, Frank R. Larson

Temperature-dependent functions of various ten-sile flour stress and fracture parameters were investigated on iron and low composition alloys of Fe-C, Fe-Cr, Fe-Mn, and Fe-Ni. Data were obtained over a range of test temperatures from 200" to -196"C at an initial strain rate of 0.01 min". It was found that the strain-hardening exponent, n, for the Fe-Ni alloys increased significantly at very low testing temperatures with increased alloy addition. Also, the stress and strain at fracture followed a predictable transitional type of behavior. The flour stress-temperature dependence was evaluated employing the relation: M where it is shown that composition can strongly influence the constant M. An empirical formula describing this effect is as follows: M = MI (equivalent at. pct Ni)-'" Some preliminay, tests were run on several commercial steels to test the generality of this relationship. One of the phenomenological explanations of the ductile-to-brittle transition encountered in bcc metals is based upon the difference in the temperature dependence of the flow and fracture stresses.' It states simply that the fracture stress is relatively insensitive to temperature and that the yield or flow stress rises rapidly with decreasing temperature so that, when the flow stress reaches the fracture stress, brittle fracture occurs without appreciable plastic deformation. This behavior is illustrated schematically in Fig. 1 where the ductile-to-brittle transition is shown to occur at two possible temperatures. The lowest temperature, TB, represents essentially completely brittle behavior while the higher temperature, TN, represents "notch" brittle behavior. Support for this theory is obtained when it is observed that fcc metals, which do not commonly have a ductile-to-brittle transition, also do not commonly exhibit any strong temperature de- pendence of the yield stress. This relationship of yield or flow stress behavior with the ductile-to-brittle transition has been generally observed for most metals representative of these two crystallo-graphic structures. One exception to this generalization appears in the case of tantalum where no apparent ductile-to-brittle transition has been observed. However, this may simply be an indication that this type of behavior is not directly related to the flow stress and that some other mechanism such as twinning must also be operative. A comparison of the typical temperature dependence of the yield stress of some representative metals is shown in Fig. 2. In the study of the temperature dependence of the strength of metallic materials, considerable ef-

Jan 1, 1963

By Jon Y. Kaneshiro, Ed Walton, Stephen J. Navin, Robert M. Sergeant, Storer J. Boone

The Coronado Traffic Tunnel is a proposed two-lane, reversible, road tunnel, which will relieve severe peak hour congestion problems on surface streets. The tunnel will take traffic from the Coronado Bay Bridge to Naval Air Station North Island. The project will include 12.5 m (41 ft) inside diameter by 1,112 m (3,650 ft) of tunnel, 552 m(1,815 ft) of cut and cover box structure, and 400 m (1,315 ft) of open cut structure. The geology consists of predominately clean and silty sand, saturated sand, with some clay layers, requiring Earth Pressure Balance or Slurry Shield tunneling technology.

Jan 1, 2001

By C. Ciriello

Six Sigma methodology, as applied within Xstrata (formerly Falconbridge and Noranda), involves a disciplined approach to managing projects, solving problems, improving performance, and leveraging information. The four (4) cornerstones of Six Sigma are the use of Philosophy (customer driven, desire to improve and discipline), Metrics (measurement systems), Methodology (scientific method and sequence of deliverables), and Tools (such as statistics, change management, and root cause analysis). This paper will outline the general steps of the Six Sigma methodology and demonstrate how each phase directly applies to a real plant metallurgical project aimed at reducing nickel losses of the rougher flotation circuit at Raglan. The main concepts of Six Sigma are described, along with the specific challenges, successes, and deliverables related to the project. It is also the authors' aim to demystify the basic Six Sigma principles.

Jan 1, 2007

By A. Lashgari

Surface coal mining in the Appalachian region consumes a significant amount of energy in the form of diesel fuel and blasting agents. emission of oxides of nitrogen (Nox) from these sources represents an environmental challenge to the mining industry. this paper presents the results of research work related to determination of Nox emission of mining equipment and blasting agents, which is part of a broader industrial project conducted by the Appalachian research Initiative for environmental research (ArIeS). Data for this project are collected from an operating surface coal mine in West Virginia. the research work presented here may be used by mining professionals to aid in quantifying Nox emission and determine strategies for reducing its overall environmental impact.

Oct 1, 2013

By Hernán Parra

Las pruebas cerradas de flotación (ICFT) son necesarias para el diseño de plantas a niveles de prefactibilidad y factibilidad, ya sea en proyectos greenfield o brownfield. Estas pruebas se realizan después de haber hecho un estudio previo de flotación batch y se usan para simular un circuito continuo. En este trabajo se reseñan los estudios sobre el tema, se busca establecer la manera adecuada de ejecutar la práctica de laboratorio y de evaluar los resultados experimentales, con el propósito de introducir mejoras en el diseño de plantas.

Aug 30, 2017

By C. M. McKinney

This report presents analyses of crude oil from most of the fields in the United States producing 2,500 barrels per day or more. The purpose of the report is threefold : 1) To present detailed analyses of crude-oil samples from as many al possible of the important fields in the United States. On January 1, 1947, there were 340 fields producing 2,500 barrels & day or more. Analyses for 283 of these fie1ds are presented. Fifty-seven fields have been omitted because the Bureau of Mines did not have analyses or the crude oils being produced. As one sample was not representative of the promotion from several of the fields, two analyses are given for each field of this kind. (2) To compile these analyses, many of which have not been published previously in a single report. Since the publication of Bulletin 291 in 1928, there has been no report showing analyses of crude petroleum from fields throughout the United states, but a number of separate reports according to area or state have been issued. Many of these are out of print. (3) To provide a means of ready comparison of the properties of crude oils from different areas of the United states.

Jan 1, 1948

By R. A. Gee, G. B. Ashton, S. T. Warren, P. N. Groves

Northside Storage Tunnel provides 500 megalitres (Ml) (130 million gallons) of storage capacity to capture stormwater/sewage overflows into Sydney Harbour. The6.6 m diameter TBM driven tunnel traverses Middle Harbour 85 m (280 ft) below sea level and through a sandstone/shale rock mass, highly disturbed by stress relief, 20 m(65 ft) beneath the base of the sediment filled palaeochannel. Target limits for inflow, groundwater drawdown and settlement of the valley beaches were achieved by systematic forward grouting from the TBM. Support included rockbolts, sets and shotcrete to carry rock loads, control block instability and spalling and to provide durability and serviceability. This paper describes the tunnelling and grouting works and their effectiveness.

Jan 1, 2001

By Craig R. Barreft, Oleg D. Sherby

The steady-state creep characteristics of pure polycrystalline copper were studied in the temperature range 400" to 950°C and in the stress range 400 to 7000 psi. Tests were conducted in dry deoxidized hydrogen and all specimens exhibited high ductility before fracture. Two activation energies for creep were established as a function of temperature. Above about T/T, = 0.65, the activation energy for creep was 48,000 cal per mole whereas between 0.5 and 0.65 T, it was 28,000 cal per mole. The observed temperature dependence of the activation energy for creep follows the same trend as exhibited by the self-diffusion coefficient of copper in copper single crystals and silver in silver single crystals. It is therefore believed that the rate-cmtrolling mechanism in creep of copper in the stress and temperature range studied is diffusion-dependent and is probably associated with a dislocation-climb process. The low activation-energy region is attributed to enhanced volume difFusion from the presence of dislocations which act as short-circuit paths for diffusion. THERE is extensive experimental evidence1,2 that the activation energy for creep, Q,, for pure poly-crystalline metals tested at temperatures above one half the absolute melting temperature (0.5 Tm) is a constant and equal to the activation energy for volume self-diffusion, Qsd This equality is generally interpreted as meaning that creep in this temperature range is controlled by a dislocation-climb process. The existence of high-temperature creep activation energies not equal to the respective self-diffusion values has been suggested both theoretically3"5 and experimentally.6-8 Two examples of apparent nonequality between Q, and Qsd have been reported for the cases of silver7 and copper,' where activation energies for creep much lower than those for self-diffusion persist to rela- tively high temperatures (up to 0.6 T,). These observations suggest that dislocation climb may not be the only important process in the high-temperature deformation of these metals. That dislocation climb does indeed occur relatively slowly in these two metals due to their low stacking-fault energy has been suggested by many investigators.9-10 Although the creep behavior of copper has been studied extensively at low temperatures, the high-temperature activation energy for creep is not well-defined. The data of Feltham and Meakin8 indicated that Q, is temperature-dependent above one half the melting temperature, equaling a value of -30,000 cal per mole at temperatures up to 550°C and increasing to a value of -49,000 cal per mole at 700°C. No data has been reported above 700°C. The value of 49,000 cal per mole is very near the value of Qsd for copper reported by Kuper et al." as 47,100 cal per mole. In view of the lack of high-temperature creep data and the apparent temperature dependence of Q, for copper the present investigation was undertaken to determine the value of Q, over the temperature range of 400" to 950°C. It was hoped that such a study would clearly document the temperature dependence of Q, and yield significant information as to the nature of the rate-controlling creep mechanisms. MATERIALS AND PROCEDURES The material used in this investigation was high-purity OFHC copper. After rolling and recrystal-lization treatments spectrographic and chemical analyses showed only 0.0008 pct Ag, 0.0002 pctCa, 0.0002 pct H2, and 0.002 pct O2 as trace impurities indicating a purity of greater then 99.995 pct. Specimens were machined from cold-rolled sheet and the gage sections polished with 2/0 emery paper prior to annealing treatments. Annealing was done in both vacuum and dry deoxidized hydrogen atmospheres. No variation in creep strength was found as a result of the different annealing atmospheres. The final annealing temperature was either 700°, 800°, or 1000°C depending on the temperature range to be studied. These treatments resulted in average grain diameters of 0.03, 0.4, and 1.0 mm, respectively. The precise mechanical-thermal history of these

Jan 1, 1964

By M. B. Haggerty, Joe Welna

The Minnesota Department of Transportation is constructing a stormwater storage facility (SSF) along Interstate 35W (I35W) south of downtown Minneapolis, MN. The project will provide storm surge capacity reducing the frequency with which major precipitation events result in flooding of I35W. The design consists of six, 42-foot diameter, 90-foot deep, adjacent underground shafts providing 14.7-acre feet of storage. Construction challenges include high groundwater with variable glacial outwash deposits. Constructability and ground variability were managed using construction manager general contractor (CMGC) project delivery. CMGC provides an environment for collaboration and innovation starting in the design phase and carrying through construction. This paper provides an overview of key efficiencies and collaboration examples implemented on the I35WSSF project which were aided by CMGC delivery.

Jun 13, 2023

By George Rice

Foreword Following the explosion in the Hillcrest mine, which occurred in the evening of Sunday, September 19th, 1926, and in which two men lost their lives, the writer was invited by the Hon. J.E. Brownlee, Premier of Alberta, to conduct an investigation into the causes of the disaster, and to make such recommendations as seemed advisable with a view to minimizing as far as possible the chance of future explosions in this and similar Alberta coal mines. Accordingly, the mine was visited, and extensive investigations were made underground on October 21st, 2.2.nd, and 25th, in company with Mr. John T. Stirling, Chief Inspector of Mines for Alberta, Mr. Moses Johnson, District Inspector for the Crowsnest Pass District, Mr. J as. A. Richards, Inspector of Mines, Edmonton, and also Mr. Thomas Davies, manager, and other officials of the Hillcrest mine. Hearings of the coroner's inquest were also attended on October 20th and 23rd, when testimony regarding the explosion was given by various witnesses. The following paper summarizes my general observations in tracing the place of origin of the explosion, and my efforts to determine the cause of ignition. Certain recommendations arc also made, and the writer invites discussion on these and the other matters dealt with in the paper.

Jan 1, 1928

By T. Lenarcic, R. Svrkota, J. M. McNeal, E. Prohic, S. Pirc

Paper presented at the 28th International Geological Congress held in Washington DC, July 1989 (International geochemical mapping sessions). Surface drainage samples, the usual media employed in mapping national territories, cannot be used for the geochemical mapping of carbonate terrains because there is no regular surface-drainage pattern on karst. Suitable sampling media have been studied in Yugoslavia, one-third of which consists of karst terrain. Sampling designs for the work were based on analysis of variance techniques. During initial investigations of various sampling materials in NW Yugoslavia sediment and aquatic moss from karst springs, along with soil, were established as the most appropriate media. Modified sampling procedures were then carefully applied along the entire Yugoslav karst belt, which includes terrains of contrasting topography, climate, pedology and vegetation. The studies indicate that climate and relief do not systematically influence the geochemical composition of soil. Regional and local variability was assessed for 21 chemical elements and the feasibility of producing stable regional geochemical maps was determined for a number of elements on the basis of sampling aquatic moss and sediment from karst springs and soil

Jul 1, 1991

By J. V. Ghelarducci, M. A. Sharpe, D. G. Chedgy

This article presents a novel design, called the Climax, High Capacity Processor (HCP), for pre-combustion cleaning of coal. This design is particularly suitable for the plant capacities of 400 ~ 660 TPH. The HCP is different from the conventional designs with an equivalent throughput in three major aspects: 1) the use of one large capacity HM cyclone to separate coarse and intermediate raw coal in a single circuit; 2) the elimination of the conventional secondary magnetics recovery system by use of the high efficiency Climax, magnetic separators; 3) the use of "single line" piping with a minimum requirement of ancillary devices. In comparison with conventional designs with similar capacity, the HCP plant costs much less in capital investment, operation and maintenance.

Feb 24, 1997

By S. M. Pickering

Banks frequently manage large privately owned mineral land trust accounts for estate heirs. The bank has a fiduciary obligation to follow the “Prudent Man Rule”, which requires that trust properties be managed at least as well as a prudent and knowledgeable owner could. However, banks may not have internal staff proficient at mineral property values, lease contracts, royalties, mining practices, etc. This is an opportunity for experienced geologic consultants and certified minerals appraisers to provide needed help. Items valuable to Trust managers may include: 1. Marketing privately owned mineral trust lands to mining or oil & gas firms, assuring competitive offering prices and terms; 2. Negotiating favorable new mineral lease and purchase-option contracts; 3. Monitoring progress of mining, royalty payments, land reclamation, and environmental clean-up work; 4. Balancing future mining income with later industrial, commercial or housing development, timber harvest, etc.; 5. Assuring that Depletion Allowance tax advantage is taken for actual mine royalty payments, but not for annual non-mining lease (rental) income; 6. Appraising in-ground mineral value for bank audits, estate tax valuations, and equitable property division between heirs; and 7. Serving as expert witness, representing the legal interests of the bank, trusts, and the mineral heirs in litigation. Banks do welcome reliable advice which assists them in achieving the “Prudent Man Rule” and improving mineral income to their land Trust accounts.

Jan 1, 2002

By R. A. V. Raff

Although falls of roof, face and rib (or side) of coal mines were the third ranking cause of disabling accidents in 1966, the accidents from these falls resulted in the most serious injuries and accounted for approximately 50 percent of the total fatalities (I). Further breakdown of these statistics shows that 88 percent of the fatal accidents occurred within 100 feet of the working face and that 96 percent of the deaths were in bituminous mines, with only four percent taking place in anthracite workings. These figures demonstrated the need for improved reinforcement procedures in operational coal mines, and they provided ample justification for research in the area of accident prevention. The purpose of this project was to investigate the use of polymers and of related techniques to achieve rock bonding and reinforcement of coal mine structures, in order to obtain better or permanent ground support (e.g., drifts, entrees, coal and ore passes, galleries, tunnels and shafts) by the fill ing of fissures in the rock, thereby preventing or delaying the onset of serious rock degradation processes.

Jan 1, 1973

By J. Warmbrodt, D. Apel, D. Nutakor, L. Grayson, M. Hilgers

MinerSIM is an augmented reality system with integrated hypermedia that is suitable for training underground miners in the basics of using a jackleg drill to install rock bolts. While statistical evidence shows that rock bolting with such a drill has an inherent level of risk, it is conjectured that this can be mediated with adequate safety training outside of the actual mine environment using a variety of educational media including interactive three-dimensional images, games, animations, and videos to describe the mechanics of rock bolting and its principles. Ultimately, trainees will install rock bolts in an immersive environment mixed with real and virtual images generated via a gaming graphics engine. This paper will discuss considerations, implementation issues, and evaluation methodologies of the MinerSIM system.

Jan 1, 2007

By Giovanni Barla

This paper examines the application of gelatin mixture models to the study of factors such as gravity effects, tectonic and residual stresses, anisotropy, physical nonlinearity, time-dependent behavior of the rock mass and connectedness of the geologic space. The calibration technique of gelatin mixtures, proposed by Richards and Mark in 1966, is applied to the particular problem considered. Similitude relationships between model and prototype are discussed with reference to the constitutive equations describing the physical behavior of the rock mass. The interaction between two openings in a linearly elastic medium, under conditions of plane strain, is used as an illustrative example, with the view of describing the history of stress and deformation changes on the rock medium and lining around a slusher drift while undercuts are made in block caving.

Jan 1, 1968

By E. D. Gardner

During the summer of 1935 a plan was proposed by which the Government should establish custom sampling plants for gold and silver ores in the mining districts of the West, where the construction of such plants would be justified as an unemployment relief measure. It was known that in many districts prospectors and small operators had small lots of smelting ore that could not be marketed for lack of sufficient capital to get out enough ore at a time to make carload shipments to distant smelters. Moreover, considerable ore of milling grade was available in many districts in which there were no custom milling facilities. It was felt that. accurate sampling and the classification and consolidation of small lots of ore produced from prospects and small mines, with quick cash returns to the shippers on a nonprofit basis, would stimulate the working of small gold and silver properties: Idle mines would be put to work, and there was a possibility that some of the prospects could be developed into regularly producing mines. Each sampling plant was to be centrally located so as to serve the greatest possible number of mines and prospects. Wherever possible, the plants were to be built on a railroad, is ore of smelting grade accumulated, it was to be shipped to a smelter in carload lots. Where a plant was not on a railroad, smelting ore was to be trucked to the railroad after being sampled.

Jan 1, 1936

By Diankun Lu, Ganfeng Tu, Edouard Asselin, Feng Xie

A novel separation process for detoxifying cadmium-containing residues arising from zinc hydrometallurgical processes has been developed. An initial investigation indicated that a high concentration of zinc in the sulfate solution can be effectively separated from cadmium by solvent extraction with P204 (di(2-ethylhexly)phosphoric acid, D2EHPA). The mixture of sulfuric acid and ammonium citrate ((NH4)3C6H5O7) is thus used to extract metals from the residue at room temperature. Copper in the leachate is recovered by solvent extraction (SX) with LIX 973. Cobalt in the raffinate from the copper SX process is recovered by precipitation with a-nitroso-ß-naphthol. The results show that more than 50% of the copper and virtually all the zinc, cadmium and cobalt in the residue can be leached under the experimental conditions used here. Virtually all dissolved copper and cobalt can be recovered in the subsequent solvent extraction and precipitation processes. The presence of (NH4)3C6H5O7 could significantly facilitate the extraction of zinc by D2EHPA in the subsequent separation of zinc and cadmium. More than 97% of the dissolved zinc can be recovered through a two-stage counter current solvent extraction process. After separating copper, cobalt and zinc, cadmium can easily be recovered from the solution either by cementation with zinc powder or by electrowinning, while the purified solution can be recycled back to the leaching process.

Jan 1, 2014

After a five year period representing the strongest resource and commodity rally ever experienced, we are now faced with a subdued recovery following the global financial crisis. This renewed economic growth will be steady but eventually attain levels that reignite export demand out of China and other emerging nations, which are now reliant on increasing domestic demand to support their economies. This backdrop of weaker share prices and less available investment capital creates a greater imperative for company management to ensure that its share price is fully valued. The mining geologist plays an important role in achieving this outcome through direct estimation of asset value (resources) but also in strongly communicating the æupsideÆ value opportunity in both mine site and adjacent brownfields exploration and an efficient and technically sound mining operation. The contribution of mining geologists to assist in conducting analyst site visits should not be underestimated, particularly with reduced analyst coverage of the resources sector and some simplification in company analysis through ranking companies on Reserve and Resource positions.

Jan 1, 2009

By J. D. Ramsdell

To obtain information on the effects of cobalt on microstructure and tensile properties of titanium-vanadium-cobalt alloys, the composition ranges of 4 to 16 percent vanadium with 1 to 4 percent cobalt have been studied. The beta phase was not completely retained with vanadium additions up to 16 weight-percent or in the same alloys containing up to 4 percent cobalt.

Jan 1, 1960