Search Documents

By G. W. Adams

Foreword While the literature on radium is voluminous, there is no single publication available from Canadian sources which attempts to cover at all fully the world radium industry. The comparatively recent developments in the Wilberforce area, and the consequent arousal of public interest in radium, seemed to call for the publication of such a paper which would be intelligible to the layman. To satisfy this apparent need, the writers submit this paper which contains material derived from various sources, and for which the writers make no claim of originality. Direct references are made throughout the paper to sources of information.

Jan 1, 1931

By Yue-yuan Li

China has abundant magnesite resource, but the low-grade and powder ores have always been rejected, which influences the comprehensive utilization of resource and often causes circumstance problems. The present work investigated the preparation of magnesia whisker using magnesite tailings as starting materials by preparation magnesium carbonate whisker as precursor firstly in the route of calcination, hydration, carbonation and pyrolysis, follows by second calcination of the precursor. The influence of pyrolysis conditions and additives on morphology of magnesium carbonate crystal as well as the influence of calcination conditions on morphology of magnesia whisker was investigated. The results showed that thermal decomposition products was MgCO3?3H2O. Magnesium carbonate whisker with length of 10~60 µm and the length-to-diameter ratio of 10~20 was prepared when soluble magnesium salt was added. While temperature was elevated at 1°C?min-1, magnesia whisker with length of 10~60µm was obtained.

Jan 1, 2010

By Luis E. Vallejo

The strength measured by the uniaxial compression test is a parameter that is widely used for the engineering classification of rocks. Sedimentary rocks such as shales, however, are difficult to evaluate by uniaxial compression tatting because the rocks slake during the preparation of the standard samples required for the tests. Indirect methods such as the point load test have been proposed to determine the unconfined compressive strength of shales and other soft rocks. It is current practice to use 24 as the conversion factor between the point load strength, Is, and the unconfined compressive strength, sf (sf = 24 Is). The present study investigated index-to-strength conversion factors for shales and sandstones obtained from surface coal mining sites in the Appalachian region. Regression analyses indicate that a conversion factor of 12.5 best correlated the strengths obtained from the point load and unconfined compression tarts in the case of shales. For the sandstones, a value of 17.4 best correlated the strengths.

Jan 1, 1989

By Bernard Jones

LTUG ? A meeting of many mining companies that are using large tires ? Introduction of the mines and size ? Companies go over their usage of tires and performance ? As a group we discuss how the manufactures are doing with supplies and performance (who's running what sizes and manufactures they are using) ? The mine's best practices they use (which ones work for them and which ones don't) ? Where the mines see themselves going in the future ? What type of tire management the mines have in place

May 1, 2009

By G. J. de Korte

South Africa’s best-quality coal, located in the central Highveld basin, is becoming depleted and alternative sources of coal, such as the Waterberg coalfield, will have to be developed to supply the country with coal in the future. The quality of the coal being mined in the central basin is gradually becoming poorer. This necessitates that more of the coal be processed to improve the quality to meet customer requirements. The challenge to the coal processing industry is to process low-yielding coals to produce goodquality products and at the same time ensure that coal mining remains economically viable. This requires that more cost-effective coal processing technologies be investigated and implemented.

Jan 1, 2015

By S C. Dominy

This contribution examines the effect of feedstock sampling before the sorting stage of polyethylene terephtalate (PET) bottle recycling. Batches of waste PET bottles may contain non-PET bottles which need to be removed by sorting. Any residual presence of PVC is detrimental for the quality of products manufactured from recycled PET. The maximum tolerated concentration of PVC in cleaned PET is extremely low, which places high demands on the recovery of PVC achieved by sorting. To be confident of attaining the desired PET quality after sorting, acceptance sampling of truckloads of PET bottles may take place prior to sorting. It is shown that accounting for sampling uncertainty requires that the sorting process achieves a consistently high recovery of PVC bottles.CITATION:Glass, H J and Dominy, S C, 2017. Plastics recycling and sampling, in Proceedings Eighth World Conference on Sampling and Blending , pp 129–134 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By W. F. Van Impe

The design of piles and of pile groups has remarkably progressed over the past two decades. The in­creasing complexity of the building concept implements a more rational approach of the deep foundation capacity and its interaction with the structure. Moreover, the understanding of the soil characteristics relevant to deep foundation behaviour, is continuously in progress because soil parameters are always more accurately determined; which also contributed a lot to the recent developments in pile capacity design. At last, due to the increasing sensitivity of buildings to deformations, continuous attention must be also paid to pile group settlements. The aim of this report is to discuss some of the mentioned more important pile design developments.

Jan 1, 1994

By G. Price

The Building Research Establishment installed a base load cell in a driven cast-in-place pile prior to it being tested under vertical load. The monitored base loads were found to be significantly less than could have been predicted by current design methods. The less than expected capacity was attributed to the drilling out procedure. An electro-level system installed in a second similarly formed pile, provided detailed information on the performance of the pile under lateral load. The information obtained was used to check several current design methods for laterally loaded piles. The findings show the potential dangers of attempting to improve design parameters from only limited performance data.

Jan 1, 2010

By F. D. Forgeron

"ONE OF THE FIRST DOCUMENTED APPLICATIONS of soil geochemistry in the Canadian Shield was that carried out by Chisholm in the Kenora district in 1949. This survey proved successful in outlining sulphide-associated gold veins utilizing cold-extractable metals. Since then, mining companies, government agencies - both provincial and federal - and universities have conducted soil investigations. Some of the results are documented in publications, others are on open file in provincial and federal mines departments and, unfortunately, many other investigations with both successful and unsuccessful results are buried in company files or have been discarded. This paper deals with soils within the scope of chemical studies of overburden in the Canadian Shield. The subject is a broad one and some definition is required. The soil investigations discussed herein are those aimed at the testing of specific targets more or less in the source area. This definition distinguishes soil investigations from other overburden studies which commonly monitor metal accumulations at some substantial distance from the metal source. Naturally this distinction is relative, because in many instances there is overlap."

Jan 1, 1971

By L. T. Matthews, C. E. Loo, R. P. Williams

The behaviour of iron ores and fluxes in the high temperature zone of a sintering bed is extremely complex. Following a review of current knowledge, an attempt is made to define relevant terminology to describe the processes that occur in this part of the bed. A deformation temperature is used to quantify the initial formation of melt, which is produced predominantly by reactions between fine particles in the sinter mix. The subsequent assimilation of larger particles is considered to depend on the reactivity of the melt and the assimilation resistance of these particles. Novel laboratory experimental techniques are used to quantify these parameters. Results demonstrate that the properties of the raw materials used have an extremely important influence on the initial processes of melt formation and assimilation and also on the nature of the sintering reactions and sinter-bonding phases.

Jan 4, 1992

By Andrew P. Schissler

The Citronen Zinc-Lead Project is one of the world?s largest undeveloped zinc-lead resources, containing more than 13 billion pounds of zinc and lead metal. The project is located in northern Greenland, a self-governed region of the Kingdom of Denmark (Figure 1). Citronen is the northern-most mine in the world, operating at a latitude of 83o 3? N. In excess of 67,000 meters of diamond drilling have been completed to delineate the resource. As of January 2012, the measured, indicated, and inferred reserves for the Citronen project totaled 70.8 million tonnes, consisting of 5.7% zinc + lead (3.5% zinc cut-off) (Ironbark, 2012). For the underground mine plan, room-and-pillar and long holestoping mining methods were selected. The beneficial application of structural fill was considered for increased recovery, efficient tailings disposal, and ground control. Three types of fill were compared - paste fill, cemented rock fill, and iced tailings. An environmental and economic feasibility study concluded that iced tailings was the preferred alternative provided it met the ground control requirements. The purpose of this paper is to explain the investigatory steps that led to the possibility for the use of iced tailings as structural fi

Jan 1, 2012

By H. J. de Haan, J. van Lookeren

In view of their size and favorable characteristics, Shell's heavy-oil fields on the eastern coast of Lake Maracaibo, Venezuela — known as the "Bolivar Coast" — are obvious candidates for the application of thermal recovery methods. During the last decade various methods have been tested, such as steam drive,', steam soak and in-situ combustion.3 Steam soak was discovered as a promising production method rather accidentally in 1969, during early steam drive testing in the Mene Grande Tar Sands1 When steam erupted at the surface due to breakdown of the overburden, the injection wells were back-flowed to relieve the reservoir pressure. This resulted in high oil production rates, all the more impressive because the reservoir is unproducible by primary means. It was concluded that injection of limited amounts of steam might be a very effective method for stimulation of heavy-oil wells. To obtain information that would be more widely applicable, testing of the process was continued in the eastern part of the Tia Juana field (Fig. 1). Here even more favorable results were obtained than in Mene Grande. This created sufficient confidence to prompt a large-scale project, which was considered essential for an adequate evaluation of ultimate recovery, steam requirements, mechanical problems and economic prospects. To obtain an early answer on the ultimate recovery a fairly depleted area was selected in the western part of the same field ("A" in Fig. 1). The first steam was injected in March, 1964. This paper describes the performance until the end of 1966. The production mechanism and well inflow performance are discussed in some detail. In view of the favorable results obtained so far, steam soak operations have expanded considerably since the start of this project. Presently, five other projects are under way, of which two are about the same size as the one under discussion, with further extensions being programmed. Description of the Project Reservoir Data Shell's part of the Main Tia Juana reservoir has a proven area of 8,800 acres and an average net oil sand thickness of 130 ft. It contained an initial quantity of 2,750 million bbl of stock tank oil (STOIIP), with an API gravity ranging from 10 to 15 API and a viscosity of 100 to 10,000 cp (at 122F). As a geological unit it is known locally as the Lower Lagun-illas member of the Lagunillas formation, which is early Miocene in age. The sand bodies are believed to be distributary channel sands deposited in a lower coastal plain. Most of the channel sands have lateral and some vertical communication. The field was developed mainly in the period from 1936 to 1950. The ultimate primary recovery is estimated at 18.1 percent of STOIIP, of which 12.5 percent STOIIP had been produced by the end of 1963 from some 540 wells. By then the average pressure had decreased from an initial value of 960 to 550

Jan 1, 1970

By G. R. Fitterer

In the manufacture of steel by any process the refining period involves the partial elimination of the metalloids carbon, manganese, phosphorus, and silicon, by virtue of their reactions with ferrous oxide. At the end of this refining stage the metal consists chiefly of iron in which small amounts of these materials are dissolved. Unless some deoxidizer is added to the steel at this time, the reaction between carbon and ferrous oxide will continue with such force that it is impossible to form sound steal in the ingot molds. Instead, the product will exhibit a marked porosity due to the formation and trapping of carbon monoxide-the product of the reaction mentioned. However, if deoxidizers are added, steel may be obtained which is dense and free from gas bubbles. At the same time the deoxidation products will remain in the steal as impurities. For example, silicon additions form Si02 or combinations of Si02 and FeO. Additions of manganese form deoxidation products consisting of various proportions of MnO and FeO. It is also quite obvious that simultaneous additions of manganese and silicon will form oxide combinations either in the binary system MnO-SiO2 or in the ternary system FeO-MnO-SiO2. Work at the Pittsburgh Experiment Station of the United States Bureau of Mines, in cooperation with the Carnegie Institute of Technology and the Metallurgical Advisory Board, involved the study of such deoxidizing reactions and their products. In this connection considerable information is necessary concerning FeO, MeO, Si02, and Al 203, and their various combinations. Some of the most needed data are the melting points of all of these materials. At the outset of this work ordinary methods of melting point determinations were found to be inadequate for various reasons, and the procedure finally selected involved the use of the micropyrometer with occasional corroboration by quenching methods, The reasons for this selection, together with a description of the apparatus, are given in the following pages.

Jan 1, 1932

By Probert D. H, Wright E. A, Taylor B. L

A general description of the geology of the Southern Coalfield is given. The relationship between the Illawarra Coal Measures, the overlying Triassic and the underlying Upper Marine Series, of Permian age as are the Coal Measures, is briefly explained and thestratigraphy of each is described. The eight coal seams are then treated in slightly more detail as to their thickness, quality, areas of distribution and best occurrences.In the last few years each of the authors has been concerned with one phase or other of the stTucture of the field in detail or in mining operations with the result that it is now possible to name a number of monoclines, anticlines, domes and synclines defined in detail. A minor quantitative study has been made of faults and dykes with regard to form, direction intensity and inter-relationship. It seems probable that with the further collection of data a more detailed study in these matters will be of considerable value to the economy of mining in the Southern Coalfield.

Jan 1, 1958

By James P. Kimball

AMONG the curious results of the recent advance of prices in the iron trade of the United States, one of them at least is to be regarded as of great importance. I allude to the utilization of mill cinder as a cheap and almost costless substitute for high-priced iron ores in many blast furnaces, situated within easy reach of such raw material. It has been, with but few exceptions, the practice in this country, based upon tradition rather than upon authority or European precedents, to waste this material on 'account of its high proportion of silicic and phosphoric acids, although known to contain more iron than most ores, and although also known to be sometimes applied to the blast furnace in greater or less quantities without serious detriment to the iron for specific purposes. While in use to a limited extent in the Hocking Valley and Hanging Rock iron regions of Ohio for several years, its use in Western Pennsylvania has only become general of late, under the exigencies of high prices and a short supply of ore. Especially has mill cinder largely entered into the stock of furnaces attached to rolling mills in and about Pittsburgh. Under such circumstances the cinder pig has been paddled on the premises, and the malleable iron produced has been unexpectedly good. Cautiously as at first mill cinder has been applied, it is evident that the temptation to use it freely is a strong one whenever the commercial rates for high-class ores are out of proportion to the general conditions of the iron trade, as sometimes happens in this country, especially as the free use of it is apparently justified by the quality of the iron produced from this cheap and abundant material. Indeed the consumption of cinder pig has., not been wholly confined to mills using up the production of furnaces belonging to the same plant. One furnace at least on the Ohio, at Covington, for several' months has been making foundry pig from "all cinder." The iron has gone into the general trade. It is probable that malleable iron of good quality can he made from the poorest cinder pig, but with what degree of economy will

Jan 1, 1881

By D. Kunstelj, M. Stubicar, A. Tonejc, A. Bonefacic

A. Bonefafcic, D. Kunsfeli, M. Stubicar, and A. Tonejc The present communication is concerned with the variation of the texture in aluminum wires with die angle and temperature, at constant speed of extrusion. Experiments were carried out concurrently on refined samples, with a stated purity of 99.997 pct pure A1 and commercial samples of 99.5 pct Al. Ingots of refined aluminum samples were machined to 30-mm-diam by 150-mm-long billets. These billets were transformed to 5-mm-diam wires by drawing. The final form, suitable for examination, was obtained by extrusion through conical-face dies with a 1-mm hole diam and extrusion ratio 5:l in diam. The initial form of the commercial aluminum samples was drawn wire 5 mm in diam. These samples showed a poorly defined texture with (111) as a major and (001) as a minor component. A similar defined texture appeared in the refined aluminum samples after drawing to 5 mm diam. Conical-face dies with different angles (defined by the axis and the generating line of the cone) were used in our experiments. The values of the angles were 27, 35, 45, 57, 63, and 90 deg. The extrusion container was fitted with a heating element and controller permitting temperatures up to 600°C to be maintained within i5"C. Extrusion was performed at 250°, 300°, 350°, 400°, and 500°C at constant speed (approximately 1 mm per sec) and constant die reduction. The extrusion product was a wire 1 mm in diam and approximately 20 cm long. In order to remove the surface layer with the "conical" texture and to reduce the absorption by the X-ray examination of the samples, the extruded wire was etched to 0.22 mm in diam. Experiments were performed in the middle sections of the 20-cm-long wires. In addition to the die of l-mm hole diam, dies with a 1.5-, 0.7-, 0.6-, 0.5-, and 0.4-mm hole diam and 63-deg die angle were constructed. In our experiments we did not find in these ranges any important difference concerning the texture of the extruded wires and we continued our work solely on the 1.0-mm die. The diffracted X-rays (Cu K radiation) were recorded photographically. Diffracted intensities were measured on the (111) reflection with a microphotometer. The relative amounts of texture components were determined from the areas under the diffracted maxima. We found the texture of extruded aluminum wires to be strongly influenced not only by the temperature of extrusion and the purity of the sample but also by the form of the die. It is generally admitted that cold-drawn aluminum wires have mainly a (111) texture with a small amount of (001) component, Table I of Ref. 1. In our experiments with wires extruded in conditions represented by Fig. 1, in some cases a single (001) texture was obtained. If these wires were drawn repeatedly at room temperature, X-ray measurements revealed a duplex (001)-(111) fiber texture. Further drawings increased the (111) and decreased the (001) texture component. In Fig. 1 the percentage of material oriented with (001) parallel to the extrusion direction is represented as a function of the temperature and the die angle (a), for commercial and refined aluminum samples, respectively. From these diagrams we may draw the following conclusions. The slope of the die (a) influenced more strongly the texture at the lower rather than the higher temperatures. Again, a stronger influence was found in the case of the commercial in comparison with refined aluminum samples. In the case of the commercial aluminum samples the amount of material with (001) texture increases with increasing wire temperature in an approximately linear manner. This effect is less pronounced in the pure aluminum samples, with the exception of the die with a = 45 deg. In this case the (001) texture decreases with increasing temperature, as shown in Fig. 1. Component (001) is more pronounced in higher-purity aluminum samples. Our experiments led to the conclusion that both (001) and (111) components are essentially stable in extruded aluminum wires. As we obtained a single (001) texture starting with a sample of drawn wire in which the (001) component was very weak, our experiments revealed that the (001) component is not a remnant of the initial texture; this is in disagreement with the findings of Vandermeer and McHargue.1 We gratefully acknowledge discussions with Professor M. Paic. 1 R. A. Vandermeer and C. J. McHargue: Trans. 7MS-AME, 1964, vol. 230, p. 667.

Jan 1, 1969

By Jose R. Hernandez-Aguilar

"This paper revisits data from previous studies (Hernandez-Aguilar, 2010, 2011) to better understand the link between metallurgical performance and pulp-zone bubble size (Db) in full-scale flotation systems. To obtain conclusive evidence exclusively related to the pulp (collection) zone, the experiments were designed in those studies to control both the bubble generation method and the influence of the froth zone on the overall metallurgical performance in industrial and pilot-scale flotation columns. The results showed that Db had a significantly larger effect on the recovery of coarse (> 75 µm) particles compared to the effect on fine (< 16 µm) particles. It was observed that, under certain practical conditions, the recovery of coarse particles was close to zero, but dramatically increased by reducing Db. The evidence revealed an inconsistency of the so-called “k–PSb” model: at constant froth recovery, increasing Sb (i.e., the rate of production of bubble surface area) did not always result in higher recovery, as the model predicts. Furthermore, the evidence showed that it was not the Sb but the bubble size that proved to be a more reliable link to metallurgical performance. Only in the presence of suboptimal-sized bubbles (Db > 2 mm) did the froth zone seem to play a role, possibly reflecting an effect of pulp-zone bubble size on froth stability. However, the role of the froth was negligible for Db < 1 mm.High-resolution mineralogical measurements performed on process samples revealed that, regardless of the degree of liberation, Db had a profound effect on the shape of the recovery-by-size curve, particularly the coarse particle size fraction. This observation is key as it implies that the loss in efficiency associated with floating the coarse particles was not the result of neither particle hydrophobicity nor particle detachment issues: even in the absence of mechanical agitation, liberated and highly hydrophobic coarse particles did not seem to attach to the bubbles in the first place, an inefficiency that was corrected by reducing bubble size. The data analysis suggests that poor attachment efficiency can practically affect both fine and coarse particles but via different mechanisms which are discussed here."

Jan 1, 2017

By Israel Liebman

The Bureau of Mines conducted an investigation to determine those factors that are significant in affecting the velocity of flames propagating along the boundary separating gaseous fuel and air. In addition the aerodynamic motion of the gases in the vicinity of such interfacial flames was delineated. Parameters in the study included flammable zone thickness, flammable zone concentration of gradient, fuel type, and position of the flame relative to various environmental surfaces. Of all these factors, the flammable zone thickness and burning velocity of the stoichiometric mixture were found to have the most significant effect on the flame speed. Notion of the gases in the vicinity of the interfacial flames was examined by particle track and interferometric techniques. The relative velocity of the interfacial flame with respect to the unburned gas on the central streamline was found to equal the burning velocity of a stoichiometric homogeneous fuel-air mixture. In addition, it was observed that the composition of the lean fuel-air mixture at the boundary of the combustion zone appears to be less than that defined as the fuel&apos;s lower flammable limit.

Jan 1, 1968

By Amado Yataco

El presente texto describe un cuadro comparativo sobre la producción minera comprendida entre el período de enero-febrero 2017 y 2016. En este se observa un déficit reiterativo en oro, plata, plomo y estaño y un menor avance en el cobre y zinc, dada la caída de producción metálica en Antamina. Así también se describe la caída de variación del PBI de oro, plata y plomo en febrero del presente año y la participación de cada metal en la generación del PBI minero. Finalmente se describen las exportaciones e importaciones y la evolución de los metales principales de la minería en los últimos siete meses.

May 1, 2017

By Kimberlee Falkenstein, Volha Kibitkina, Jessica Steeves

A series of experiments were conducted to obtain site specific constants for the vibration produced by a single charge and by more charges detonating in sequence, using short delay intervals. All charges were placed in relatively long boreholes in granite without a free face other than the ground surface. The boreholes were filled with water to provide good coupling with the rock and to provide identical confinement for all the blasts. Vibrations were recorded close to each blast in the vertical direction by uniaxial high frequency geophones and far field using a triaxial geophone.

Jan 1, 2013