Search Documents

By O. C. Blade

The term "Ichtnyol" is a name applied loosely to certain preparations used in pharmacy. These preparations do not occur as such in nature but are manufactured by various chemical processes. Ichthyol is the name trademarked for a product manyfactured by the Irhthyel-Gescllschaft (Cordes Hermanni & Co.) of Hamburg, Germany, and marketed in thin, country by Merck & Co., Inc., (5, 86, 87)3/. Although used in the literature rather loosely, the correctly applied word refers to the product obtained by sulphonating and then neutralizing with ammonia a distillate from the oil retorted from a certain high-sulphur bituminous shale found near the village of Seefeld in the Austrian Tyrol. Due to the fact that fossils of fish and marine animals occur in the limestone associated with the bituminous shale, these deposits have long been known as, the "lchthyolite schistc of Seefeld" ( 55) . The Greek word "ichthys"" for fish and the Latin word "oleum" for oil are the words from which the term is derived. The crude, tarry shale oil, whose distillate is the raw material for the sulphonation process, has been referred to since the Middle Ages as "Dürsten" or "Tirschen" oil, and the term "ichthyel oil" has been used occasionally in the literature to designate the retorted crude oil (92, 93, 106, 117). The first application of the name "Ichthyol" to a particular product is credited to Schröter (35, 129). Various names for products manufactured by sulphonating bituminous distillates have been coined, and in some of these names the root from the word ichthys has been retained. Some of these names can be found in New and Nonofficial Remedies under the heading, Sulphoichthyolate Preparation, and Substitutes (5).

Jan 1, 1938

By S. C. Tadolini, J. M. Goris, J. L. Gallagher

Cable supports offer several advantages over traditional secondary support methods by enhancing stress redistribution to pillars and gob areas, minimizing or eliminating timbers and cribs that reduce ventilation, eradicating material-handling injuries related to placement of crib supports, and providing a cost-effective alternative to secondary support. The U.S. Bureau of Mines (USBM), researching alternatives to traditional roof support methods, designed and installed high-strength cable supports to improve the stability of longwall gate road entries in a western U.S. coal mine. With the cooperation of industry, methods were developed to install and evaluate cable supports in a tailgate area using traditional resin cartridges. The cable-bolted areas successfully maintained roof support throughout the developed entries. Cable supports have replaced wood cribbing as secondary support in the bleeder entry system and have minimized or eliminated the use of cribbing in the longwall tailgate entries. This paper describes the theory, application, and advantages of cable supports and presents some mine measurements made to assess the cable performance during the retreat process of longwall mining.

Jan 1, 1999

By Roderick Eggert, Dipesh Dipu

We look at the empirical evidence of coal block auctions in India to understand how competitive intensity affects the bid amounts in common value auctions. The results suggest that competitive intensity measured through the number of bidders for a coal block is instrumental in determining the bidding outcomes. The presence of higher numbers of bidders in the auction leads to higher bids - every additional bidder causes the bid amount to rise by INR 142.67 per tonne of coal for auctions studied for 127 coal blocks from 2014 to 2023. The paper also examines the moderating and mediating effect of competition on bids and on excess of bids from the comparative market price of coal from alternative source of Coal India Limited. The results indicate that competitive intensity does not have statistically significant impact on the relationship between common value of coal blocks and bids, neither as a moderator nor as a mediator. The strategic behavior of the bidders has also been observed as bidders have been seen to bid in a higher than market price in order to outbid the competitors.

Feb 1, 2025

By O. Ditsele

Coal plays an important role in the energy needs of the World. Given its wide abundance and low cost, coal use is bound to increase with the growing energy demand. Despite its importance, there are growing concerns over coal?s environmental burdens, especially its contribution to greenhouse gas emissions. To ensure sustainable extraction and use of coal, opportunities for minimizing potential impacts from coal have to be identified and exploited. Whilst extensive work has been done on life cycle assessment of coal use, especially in electricity generation which uses the bulk of coal produced, there has been limited work focusing specifically on coal mining. This study aims to estimate the cradle-to-gate life cycle climate change impacts of coal from a surface coal mine in the United States. The study employs general principles of ISO standards for LCA.

Jan 1, 2010

By VIVEK KASHYAP, PATRICK TAYLOR

Zinc ferrite is the major phase component present in zinc refinery residue (ZRR) and electric arc furnace dust (EAFD). Up to 71 percent zinc ferrite has been reported to be present in ZRR, and in most studies zinc ferrite has been deemed the major phase in EAFD. In 2010, the global annual production of EAFD was 3.7 Mt, with 15.20 kg of EAFD generated per ton of recycled steel [1]. The generations of ZRR and EAFD have been growing over time, requiring a greener approach for the reutilization and extraction of valuable elements. ZRR can be a potential source of zinc, as its zinc content is as high as 30 percent [2,3]. The presence of zinc ferrite makes the extraction of zinc difficult because zinc ferrite is refractory to leaching, and direct leaching is inefficient. The Waelz process is currently employed to extract zinc from EAFD and other metallurgical wastes. The Waelz process operates in the temperature range of 1,100 to 1,500 °C and uses coke as reductant. This study explores a carbon-free and relatively low-temperature process for the selective extraction of zinc from pure zinc ferrite.

By Christos Roumpos, Philip‑Mark Spanidis, Francis Pavloudakis

Coal mining operations are large-scale, long-term frameworks of high complexity. Mining organizations accumulate, develop, and leverage knowledge from diverse scientific and technological fields as a result of these operations. Both practical experience and existing literature indicate that knowledge management (KM) methods within the mining industry primarily target solving immediate technical challenges and operational requirements. However, they are not commonly regarded as strategic tools to enhance the performance and competitiveness of mining companies. Empirical evidence from the Greek mining industry suggests that the management of available knowledge is intricate, less effective, and dysfunctional. This paper presents a methodology based on the principles of quantitative research (QNR), collaboratively conducted with a group of mining experts, to assess the KM landscape in the Greek mining industry. The methodology involves a structured data collection framework using questionnaires, subsequent statistical analysis, a discussion on critical methodological aspects, and an interpretation of results focusing on key aspects useful for planners and designers of KM systems in the mining industry. Finally, the paper concludes by summarizing the methodology’s outcomes and proposing further perspectives for research.

Mar 16, 2024

By O. P. Hood, R. H. Kudlich

When a gasoline locomotive is used in a mine there is danger of the noxious gases of the exhaust vitiating the air, but if enough air is circulating in those parts of the mine in which the locomotive is used, these gases are so diluted that they are rendered harmless, and the health of the workmen is not affected. In some mines the use of gasoline locomotives is impracticable, though in the majority of mines where they have been tried they have proved to be safe and economical. To determine the limitations that should surround the use of these machines in mines so that they shall not be detrimental to health and so that their economic advantage may be retained, it is necessary to ascertain the volume and the character of the exhaust gases and the amount of these gases that may be safely allowed in the mine air, and also to determine safe conditions of operation. The problem is primarily one of ventilation and like all ventilation problems must be intelligently computed to meet the conditions of each mine. The investigation described in this bulletin was undertaken 'by the Bureau of Mines in an endeavor to obtain exact information on some of the basal questions involved in the use of gasoline locomotives in mines, this investigation being one of many that the bureau has been conducting in its efforts to increase safety and efficiency in mining.

Jan 1, 1915

By J P. Sykes, A Trench

"World-class mine projects are increasingly failing to become world-class mines. Non-technical, socio-political and environmental problems seem, in part, to be the cause. However, the intangible and qualitative nature of these problems means overcoming them will require a greater systemic understanding of how the various technical and non-technical factors interact. This is particularly important as the concept of sustainable development has changed the industry paradigm sufficiently that it is no longer clear what world-class means. Finally, this better systemic understanding of mine projects needs communicating back to the exploration sector to improve exploration targeting.However, a disconnect between the exploration and mining sectors and between geologists and mining’s other professional disciplines means this is currently not possible. The use of economic evaluation techniques to assess the risk and value presented by the various technical and non-technical factors can assist with this by giving the varied professions a common language and including inputs from all disciplines. This paper therefore suggests a theoretical framework for analysing the various technical and non-technical factors, particularly the most challenging intangible and qualitative ones, and incorporating them into the typical economic evaluation techniques used in the mining industry.Understanding the risk and value relating to both technical and non-technical risks, however, places a greater emphasis on mining geologists to be conversant with a wide range of disciplines. Mining geologists will have to develop three types of knowledge:focusedinter-disciplinarybroad. In addition, they will have to become systemic thinkers to connect these types of knowledge. This multidisciplinary approach will require the use of fundamental critical thinking skills, common sense, intuition, experience and quantitative modelling techniques, dependent on the situation. As a result, both companies and professional societies, such as the Australasian Institute of Mining and Metallurgy, will have to develop ways of improving mining geologists’ inter-disciplinary and broad knowledge.CITATION:Sykes, J P and Trench, A, 2014. Resources versus reserves – towards a systems-based understanding of exploration and mine project development and the role of the mining geologist, in Proceedings Ninth International Mining Geology Conference 2014 , pp 243–270 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 18, 2014

By J. R. Thoenen

This circular is the third of a series summarizing the technical problems involved in the production and preparation of sand and gravel. The first, Information Circular 6668, published in December 1932, discussed the problems involved in prospecting and exploration. The second, Information Circular 6689 (March 1933), dealt with the development of gravel deposits. This is part I of a paper designed to present a study of problems arising in the excavation of sand and revel and their delivery to the treatment plant. Other circulars are planned which will discuss preparation of the material for market, plant storage, and miscellaneous subject. Definitions For the purpose of this circular, excavation is defined as the recovery of sand and gravel from developed natural deposits and their delivery to a plant for market preparation.

Jan 1, 1934

By S. Mudau, P. Mohasoa, M. J. Cole

Derelict and ownerless (D&O) mines in South Africa have been an ongoing concern for over a decade. While some progress has been made to rehabilitate D&O asbestos sites, significant work remains, exacerbated by the growth in illegal mining. There are concerns regarding the accuracy and transparency of the D&O database, lack of oversight, and constrained funding, and the government is increasingly looking to the private sector to fund rehabilitation. Given these challenges, a new, sustainable approach to D&O sites in South Africa is needed to bring clarity and transparency to the process, recognise responsibilities and promote partnerships, and explore economic opportunities at D&O sites to reduce the financial liability and respond to the growing demand for critical minerals. This article has three components: i) reviews of international D&O good practices; ii) it analyses South Africa’s current approach and the D&O sites; and iii) proposes a D&O framework that addresses data, risk ratings, responsibilities and rehabilitation, economic opportunities, and stakeholder engagement. The study finds that the majority of the 6,100 so-called abandoned D&O mines are quarries and mine site features, 16% are operational, at least 11% have owners, and only 752 (12%) require rehabilitation. The framework aims to bring clarity and fairness to decision-making and to assign risk and responsibility for rehabilitation and seeks to incorporate economic opportunities to reduce the financial burden of rehabilitation, create jobs for local communities, and respond to the growing demand for critical minerals for the clean energy transition.

Apr 25, 2025

By J. M. Benson

Metal powder compaction offers unique advantages in the manufacture of net-shape components using techniques such as laser sintering, conventional press and sintering, metal injection moulding, direct rolling, direct forging, and hot isostatic pressing. If the output from the primary metal production process is in powder form, then considerable cost and energy savings can be realized by direct conversion to semi-finished or final shapes. This possibility exists for titanium and possibly also for Ta, Zr, Hf, and Nb metals. However, these attractive benefits are associated with some significant risks. The high surface-to-volume ratio of powder particles coupled with the reactive nature of these metals means that special care must be taken when handling them. Powder explosions are unfortunately still a regular occurrence internationally and these often result in serious injury and loss of life. Even seemingly 'safe' compounds such as sugar, flour, and grain can be extremely hazardous when handled or milled and dust clouds are produced. In addition, exposure to airborne particles can have adverse effects on the human body, especially when particles are inhaled on a regular basis. Furthermore, the medical consequences of these are not fully understood, especially in the case of nanoparticles. The impact is often not observed immediately and debilitating illnesses may emerge only years or decades later. As far as is known, there are no South African guidelines for handling of metal powders. This paper attempts to provide an awareness of the risks associated with metal powders (including those produced indirectly by other metalworking/finishing operations) as well as some guidelines for their safe handling, based on international best practices.

Jan 1, 2012

By William Gleason

While a fleet of 100 t (110 st) haul trucks were busy removing overburden from the open pit mine in the distance, a host of dignitaries, including congressmen and California state representatives, gathered for Molycorp?s official groundbreaking ceremony at the Mountain Pass Mine on April 20. The mine, recognized as arguably one of the richest rare earths deposits in the world, is at the center of Molycorps? strategic ?Mine to Magnets? plan. It aims to secure America?s future supply of rare-earth-dependent technologies by developing a strong domestic rare earth industry. Molycorp identifies rare-earth-dependent technologies as those that cannot be produced without rare earth materials. The list of these technologies is long and growing. It encompasses everything from personal electronics and batteries for hybrid cars to permanent magnet generator wind turbines and national defense applications.

Jan 1, 2011

As part of the United States Department of the Interior, Bureau of Mines Health and Safety Research Program, Walter C. McCrone Associates, Incorporated has examined 71 samples of airborne mine dusts using the techniques of x-ray diffraction, electron microprobe analysis and light microscopy. This report details the procedures which were used in this work and documents the results which were obtained.

Jan 1, 2011

By R. Luchese de Moraes, J. A. Matthews, C. Feliciano Bruzual

The role of biomass char in blast furnaces has been re-examined by scientists worldwide, as a feasible option to reduce the carbon intensity of ironmaking. This contribution makes a technical and economic analysis of the ferro gusa industry in Brazil, with the last 172 charcoal-Blast Furnaces operating in the world. A key strategic question is presented: what is the current status and future prospects of biomass use in Blast Furnaces? Findings provide significant implications to metallurgists: while ferro gusa from charcoal is regarded as carbon neutral iron with low impurities, there are limiting factors that hinder the further proliferation of charcoal-BFs: biomass generation requires vast extensions of arable land and aggregates have low production capacity. Additionally, most of the charcoal is presently generated in beehive kilns with low yields. These elements combined make charcoal-hot metal expensive in price. With respect to the future prospects of biomass, the injection of small biochar particles through the PCI rigs in BFs (here coined Bio-PCI) and iron ore sintering may offer a practical alternative to significantly reduce the CO2 emissions in the ironmaking process.

Jan 1, 2015

By H. Kinilakodi, R. L. Grayson

In 2010, the U.S. Mine Safety and Health Administration (MSHA) began holding hearings on a new coal mine respirable dust rule, which proposed a 1.0 mg/m3 standard, a separate 0.1 mg/m3 quartz standard, and the use of single-shift samples for compliance. Small mines largely comprise the “hot spots” where dust diseases of the lungs increased dramatically over the past decade. This paper presents findings on the feasibility of small mines’ compliance with the proposed new 1.0 mg/m3 standard. It gives probabilities of noncompliance by MSHA district, average mining height and selected “hot spot” counties. Because silicosis and respirable quartz dust appear to be the primary issues related to a recent doubling of the prevalence of dust diseases of the lungs, multiple regression models for prediction of the average total quartz content of compliance samples are given. These findings have significant implications for the need for better dust control methods.

Jan 1, 2012

"SUMMARYThe K.M.A. reservoir was discovered to be oil bearing at a depth of 3,719 feet on March 11, 1931. Extensive development, however, was not begun immediately, because the discovery well had a low initial daily oil production, and market conditions for oil were unfavorable. Development of the field progressed slowly for the next 6 1/2 years. In the latter part of 1937, a wildcat well approximately 2 miles southwest of the discovery well was drilled on a magnetometer high and completed with an initial flowing production of 2,016 barrels of 43° A.P.I.-gravity oil in 12 hours. Rapid development of the southwestern part of the K.M.A. field was begun immediately and continued until over 700 wells were drilled and approximately 12,500 acres proved oil productive.Because of the large size of the entire K.M.A. field, this report is limited in scope to the southwestern part only, and the discussion that follows pertains to this area only. The closing date for production statistics is August 1, 1949.The K.M.A. structure is a complex anticline having a maximum closure of 250 feet, and the K.M.A. formation is composed of sediments that grade from limestone through sandy lime and limy sand to sandstone with thin streaks of shale. Two distinct members of the K.M.A. formation, zone I and zone II, are oil productive. Core analyses indicate the average porosity to be 16.5 percent for zone I and 16.1 percent for zone II. A relationship was established from core data, which showed the correlative permeabilities to be 42.1 millidarcys for zone I and 39.5 millidarcys for zone II, whereas the arithmetical averages of the permeabilities were 84 millidarcys for zone I and 216 millidarcys for zone II. Connate water saturations were 17.5 percent for zone I and 20.0 percent for zone II. The porosity-saturation method, using a thickness-correction factor, was employed to calculate the volume c 168.1 million barrels of stock-tank oil initially in place in the reservoir. Analyses of the reservoir oilIn that, although the initial reservoir pressure was 1,750 p.s.i., the original reservoir oil was saturated to only 1,300 at which pressure 1 barrel of stock,tank oil contained 525 cubic feet of gas in solution.A serious decline in reservoir pressure during the 2 years of rapid development alarmed the operators and caused them to consider a cooperative pressure-maintenance program. In the latter part of 1939, the K.M.A. Pressure Maintenance Association was organized, and the gasoline plants in the field agreed to process the wet gas and return the dry gas to leases having gas-injection wells. Approximately 27 percent of the cumulative volume of produced gas had been returned to the reservoir by August 1, 1949."

Jun 1, 1952

By John A. Davis, David W. Brunton

During the past few years great progress has been made in the United States toward safer, more efficient, and more economical tunneling methods. This advance is partly due, no doubt, to the recent increase in the number of tunnels and adits driven for devel- oping and draining mines and transporting ore. The Bureau of Mines during 1911 and 1912 made a special examination of this phase of mining operations, in connection with an investigation of mining methods and means for preventing accidents. The details especially studied were the provisions for the safety of employees, the kinds of equipment, the methods of driving, and the costs of con- struction. The results and conclusions obtained from that investi- gation are discussed and summarized in this bulletin. Up-to-date information concerning tunneling methods is difficult to obtain. There are few books on the subject; and much of the material they contain, although interesting and of value historically, is now obsolete. The engineering periodicals, it is true, endeavor to keep abreast of the times, and several in nearly every issue present some article bearing upon tunnel work. But the very multiplicity of these articles prevents one from reading them all, and the foreman or superintendent in charge of a tunnel, or the mining engineer designing one, and especially the business man financing the project, has no time for a lengthy search after scattered articles in order to determine the present status of tunnel work. Then, too, knowledge of new methods travels slowly. Valuable inventions and improve- ments in tunneling as well as in all the other industries frequently remain in the notebook of the investigator, or as theses are buried in university libraries, or are published only in journals of small scien- tific societies. New tunneling methods and equipment that are prov- ing safe, efficient, and economical may be totally unknown outside the district in which they originate. This paper, based on a special examination both in the field and in engineering literature, is in- tended to supply data concerning modern and recent tunneling practice in the United States, and to make suggestions that, it is hoped, will result in a saving to the mining industry of energy, capital, and life.

Jan 1, 1916

By Mitchell L. Spencer, Viswanathan Panchanathan

"Bonded magnets are important category in permanent magnets. They are made by one of the following processes: compression bonding, injection molding, extrusion, calendering. An overview of the various bonded magnet processes and properties of products made with different magnet materials along with their applications are discussed. The main emphasis will be on the use of bonded NdFeB and ferrite magnets.IntroductionBonded magnets are a major growth area in permanent magnets. Bonded magnets are made by any one of the following processes: Compression bonding; Injection Molding; Extrusion and Calendering [1,2]. Compression and injection molded magnets are rigid magnets. Materials used in calendering process produce flexible magnets. Only the extrusion process makes both rigid and flexible magnets. The binders used for the bonded magnets vary depending on the processes. Thermoset, thermo-plastic and elastomeric binders are respectively used in compression, injection and the calendering process. Extrusion molding uses elastomers or thermo-plastic materials. The most co=on magnetic materials, Ferrite, SmCo, Alnico and NdFeB can be used in any of the above processes either alone or in combination as hybrid magnets. Another material that has been developed for co=ercial application is SmFeN. Making the material has been challenging and it is being used in niche market applications in limited quantitiesIn the extrusion process, a highly loaded compound is used to produce strip or sheet and is continuously extruded through a die. In calendering the granulated compound is rolled to produce a continuous wide sheet. In the compression bonding process a uniaxial pressing force is used. These magnets have higher loading compared to injection molded magnets. In injection molding the material is forced into a mold cavity and has lower loading compared to compression molded magnets [2,3]. Most of the flexible magnets are made using extrusion and calendering processes and the most co=on magnet material is inexpensive ferrite. Flexible magnets have been made using rare earth materials, but on a very limited basis.The major advantages of magnets processed by extrusion and calendering are as follows: inexpensive tooling, automation; practically any 2D geometry; fast production rates; no chipping or breaking; a wide range of properties; on-line magnetization; easy to convert (e.g. cut, punch or shape).Compression bonded magnets are inexpensive to manufacture. They have higher magnetic properties compared to injection molded magnets; however lower than their sintered counterparts. The magnet shape is restricted to simple geometries and they require careful handling. Their isotropic nature allows complex magnetizing patterns."

Jan 1, 2013

By H. Foster Bain

The war has brought about many changes in the Western States, and some have deep pr sent or potent al economic significance. The West has been feeling severe growing pains for a number of years. Especially since the beginning of preparation for national defense and through the period of

Jan 1, 1945

By Georgene Renner, Chee Theng, William Gleason

"In February 2018, drawn in part by the states’ proud mining heritage, SME took its Annual Conference & Expo to Minneapolis, MN for the first time. More than 5,000 people and 554 exhibitors converged on the Minneapolis Convention Center for three days of networking, exhibiting and technical sessions.The state’s mining legacy, one that continues today, is fueled in large part by its vast iron ore resources in the northern part of the state. The historical significance of the mines in the Mesabi Range, otherwise known as the Iron Range north of Lake Superior, cannot be understated. “Mining is a way of life here,” said U.S. Congressman Rick Nolan of Minnesota’s 8th Congressional District. A native of the Iron Range, the three-term U.S. congressman was one of the featured speakers of the opening keynote session. “We like to think we contribute enormously to the well-being of this country and the world. We were the source of the iron ore and steel that helped win two world wars. And we like to think that we are part of the progress that has taken place in the United States ever since.” Nolan kicked off the keynote sessionthat focused on innovation and its part in the mining industry. The session included Rene Aquilar, vice president of corporate affairs and sustainability, Antofagasta Minerals Group; Bob Anderson, vice president for research and development, 3M; Rolf Weberg, executive director, Natural Resources Research Institute, University of Minnesota-Duluth and Christopher Beck, executive vice president and president, Nalco Water. The panel session looked at U.S. and global minerals production, and the importance of the United States to maintain a major role in the minerals industry, both as a producer and as a technology leader. The panel also touched on the global mining industry and the issues that impact mining around the world. Sustainability, the use of water in mining and earning a social license to operate were among the topics discussed by the panel.Speaking of the importance of mining, Nolan conceded that talking about the benefits of mining to the crowded auditorium at the SME conference might be akin to a preacher speaking to the choir, but, following the adage that all politics are local, he continued to illustrate his point by emphasizing the importance of mining to the Great Lakes.“A study by Homeland Security concluded that 13 percent of the nation’s GDP comes out of Lake Superior through the locks at Sault Ste. Marie and most of that is iron ore,” said Nolan. “That study found that, if those locks fail, it would create a national depression. It would put millions of people out of work. That ore and those minerals supply the steel mills, the auto industry, the heavy industrials. They are the heart of our economy. The study concluded that if the states that make up the Great Lakes were a nation, it would be the fourth largest economy in the world.”"

Jan 5, 2018