Search Documents

By John W. Fredland

Many accidents occur in the mining industry as a result of the instability of material during handling and processing operations. Accidents due to dump point instability at stockpiles, and at spoil or waste piles, for example, occur with alarming frequency. Miners must be trained to be better aware of these hazards. Information on safe working procedures at stockpiles and surge piles is provided. Mine operators must review their training and operating procedures regularly to ensure that hazardous conditions are avoided.

Jan 1, 1993

By T. P. Mucho

Over the past several years, two types of roof control problems have been en- countered at Beth Energy's Eighty Four Complex mine in Southwestern Pennsylvania. These problems have been (1) poor roof conditions encountered while advancing submain entries and longwall panel entries and (2) deterioration and failure of long- wall gateroads, principally the tailgate entry. This paper discusses the efforts by mine personnel to analyze the origins of the various attempts to-deal with the problems, and the success (or failure) of these efforts. Highlighted are the use of various common roof Control materials, variations in mining techniques, cementatious pillars, and changes in pillar design using yield and abutment pillars to address these problems.

Jan 1, 1986

By Dan Payne

The Crinum mine has recently completed workings in the southern area of the mine. Over the 10 years of longwall production 40 million tonnes have been extracted and the mine has experienced over 40 longwall face, 3 main gateend, and 2 tail gateend roof falls as well as 5 roadway roof falls away from the longwall. Weak roof (less than 10MPa (1450psi) in the bolted horizon) has been the principal roof control issue at the mine. However, weak, highly cleated coal, water inflow from overlying aquifers, some minor structure and a diatreme in the main headings have also contributed to the challenges at the mine. This paper describes the geotechnical experience over the 10 years, the mine?s approach to addressing the issues and the relative success of these approaches.

Jan 1, 2008

By Anthony Iannacchione

Designing coal pillars to provide resistance against overburden loads has long been an aim of rock mechanics engineers. The need for accurate pillar strength models has become more urgent as greater overburdens are encountered and pillar sizes grow larger. Current pillar design models differ widely in their predictions of the trend in pillar strength with increasing pillar width-to-height ratio. The goal of this paper is to evaluate current pillar strength theories, using a comprehensive data base of stress measurements from coal pillars. The stress measurements indicate that coal pillars maintain relatively high stresses near the ribline, and that the stress gradient within the yield zone can be approximated as a straight line. Several problems are identified for further research, including calibration procedures for different types of stress cells, strain softening behavior in the yield zone, and measurement of stresses in the cores of very wide pillars.

Jan 1, 1992

By Gang Chen

Conventional methods designate a factor of safety, a deterministic number, to indicate the stability of a mine excavation. However, this deterministic description of excavation stability is frequently insufficient or inaccurate and, sometimes, misleading. Employing the probabilistic analysis to determine the likelihood of mine excavation failures will lead to a better understanding of ground control problems and result in more rigorous designs of the excavations. Based on the theory of probability, two approaches are taken in this study for the probabilistic analysis of excavation stability. The first one utilizes direct integrations for the estimation of failure probabilities of mine excavations. Due to the complexity of the integration, this approach can only be applied to solve relatively simple problems. In order to overcome the limitation of the direct integration method, the second approach employs the first-order second-moment approximation of the failure probabilities for more complex ground control problems. The probabilistic analysis offers a deeper insight into the uncertainty associated with the stability of mine excavations. The study indicates that the distributions of parameter values play a significant role in the mine excavation stability, which can not be disclosed by the conventional methods of stability analysis. Greater dispersiveness of the parameter values will lead to a different probability of failure, although the factor of safety estimated by conventional methods stays the same if the mean values of the parameters are constant. By taking consideration of the probabilistic distributions of the parameters, the probability model can provide more reliable designs of mine excavations.

Jan 1, 1996

By Victor V. Nazimko

Long term stability of the pillars that have been remained after R&P extraction causes postponed subsidence. To prevent unforeseen subsidence and to diminish postponed subsidence 25-50% new method for its control has been developed by the author. It supposes to use drilling and blasting technology and other original approaches. New method has been fulfilled through the holes being drilled from the surface or from the active underground openings. Explosives had been charged into the holes and were blasted. This had increased bulking factor dramatically and prevented natural caving of the strata. Physical scale modeling corroborated efficiency of the new approach. The bulking factor has grown from 0.0623 to 0.1185 and surface subsidence has been diminished from 1.1 m to 0.2 m or 5.5 times.

Jan 1, 1996

By Andrew P. Jarosz

The present computerized mine planning systems use CAD-like and Data Base Management System (DBMS) environments for the handling of numerical, textural, and graphical data. These two environments are usually integrated, that the data provided by the DBMS are linked to any graphical element rendered by the CAD system. The subsidence monitoring, analysis and prediction process should be integrated with the mine design process. It should allow for the assessment of impacts of mining on surface, surface utilities, and structures. It should also provide for the measures to control mining, that will create only acceptable levels of negative impacts on the surface. The common data base, and graphical capabilities of the CAD interface, may be used with great advantage for both systems. The findings of the subsidence engineering modulus should be directly incorporated into the mine design system, and vice versa. In this paper the author suggests guidelines for the development of the comprehensive computer system, able not only to predict the vertical and horizontal components of the ground movement, but also assess the induced surface damages, and costs related to subsidence prevention and compensation.

Jan 1, 1995

By Ken Mills

A program of stress change and roadway deformation monitoring was undertaken to measure the forward abutment load distribution about a retreating longwall panel at Dartbrook Mine. The results of this monitoring allow roadway conditions observed at various stages of mining to be ranked according to the estimated vertical stress they have experienced. This ranking also provides a means to predict and visualise future roadway conditions at various stages of mining. This paper presents the results of the monitoring and describes the approach developed to predict future roadway conditions. The monitoring results show the vertical stress distribution associated with the front abutment from a longwall goal decreases exponentially away from the goaf edge. The vertical stress distribution peaks at the goaf edge at 5 to 6 MPa stress increase and decreases to 1 MPa within 50 m becoming imperceptible beyond 100 m By scaling this measured distribution to reflect the loading environment, the vertical stress can be estimated for different overburden depths and different stages of mining. Photographs of roadway conditions at particular vertical stress levels provide a way to visualise roadway conditions at various stages of mining in the future

Jan 1, 2000

By G. I. Gritsko

In this paper we consider the elements of a distributed information geomechanic monitoring system which is used in computerized mine planning and mining operations control. The automated system is a technical means of geomechanic monitoring, as a complex system of regulated observations, estimation and prediction of geomechanic state of rock mass and workings during underground mining of coal deposits. Geomechanic monitoring at coal mines and the automated system execute data collection, analysis and calculations of geomechanic situation in the panel during planning, development and carrying-out of mining operations for ensuring geotechnical stability of underground mining.

Jan 1, 1996

By Mike Faure

Hercules cribs make use of timber loaded parallel and perpendicular to the grain. Maximum use is made of the orthotropic properties of timber resulting in crib- having superior strength, high initial stiffness and controlled post yield deformations. Blocks and timbers can be combined in many different ways resulting in thousands of different geometries. Each geometry has a specific combination of block on block, timber on timber and block on timber contact area which results in a unique performance. Each crib can be fingerprinted by defining four parameters relating to its load/deformation curve. If the geometry is known, the performance can be predicted with a high degree of accuracy. If the mine support requirements are known, the crib geometries can be designed which met theme requirements in the most cost effective manner Hercules cribs come closest to satisfying mine support requirements. Due to the flexibility of the concept and their superior strength, they can be employed in most mining situations to enhance safety, improve productivity, reduce working costs or improve profitability.

Jan 1, 1993

By Vincent A. Scovazzo

Many accepted and useful methods have been developed and used for pillar design. Each method has its own particular strengths and weaknesses. Three methods addressed in this paper are; empirical, analytical, and numerical. Each of these methods have their place in pillar design. Analytical methods result in close approximation of the ideal pillar (most economical, stable, or yielding) and are suitable for use in final mine design and in analyzing existing problems. BOYD uses the analytical method to develop site specific mine pillars design equations. An analytical method, one of many developed by BOYD, is presented here and is based on the procedure used by Wilson (1) and others in development of their empirical equations.

Jan 1, 1995

Continuing with the effort of providing new and more effective exploration methods to the mining industry, where direct methods (drilling, cross-cutting, etc.) are not applicable, either for logistical or environmental reasons or because they are costly and sometimes ineffective, we present here a new seismic technique based on full wave recording of 3-D channel waves generated within the coal seam across a longwall. In the past two years we reported the application on In-Seam High Resolution Seismic Reflection (ISHRSR) and In-Seam Seismic Tomography (ISST) to map non-coal inclusions that disrupt the coal seam continuity. In the present paper we present a 3-D In-Seam Seismic Tomography (3-DTSST) method using 3-D channel waves recorded by three component high resolution geophones. The method allows to distinguish longitudinal and transversal components of the channel waves, similar to the spheroidal and toroidal modes for the free oscillations of the earth. The recording of these waves allows a more complete analysis of the free modal vibrations of channel waves, permitting a more complete inversion of the structure of the coal seam through which they travel. The full wave analysis provides additional insights of the detailed coal structure for larger, distances than for the ones previously reported using the one dimensional method. The refinement of the inversion software is also a contribution towards the better definition of the coal seam geometry and structures disturbing them such as sandstone channels, sandstone rolls, partings, mine voids, faults, fractures, etc. The method is illustrated with three case studies where subsequent mining revealed the virtues and limitations. The first example deals with the problem of mapping mine works in one side of a longwall panel which geometry is well known, to verify its applicability to map old mine works. The second example deals with a sandstone body that partially scoured the coal seam withing a longwall panel. The third shows an application of the method to map roof conditions in a longwall panel where this problem critically affected production scheduling and costs

Jan 1, 1996

By Jun Lu, Mark Van Dyke, Daniel W. H. Su, Greg Hasenfus

"This paper presents the geologic and ground control challenges that were encountered by CONSOL Energy’s mining operations in southwestern Pennsylvania. A sandstone-to-limestone geology transition was encountered by Mine A, where the primary 8-foot bolts were anchored in claystone. Upon experiencing roof sags and a roof fall in the return entry, 6-foot high-tension, fully-grouted primary bolts were employed along with 16-foot center cable bolts at every other strap to improve beam building and to ensure proper anchorage into the competent limestone. No longwall delay was reported within this geologic transition zone, although there was some difficulty in maintaining an open #2 entry airway behind the longwall face.The geologic encounter in Mine B was more complex, where fluvial deposits of massive sandstone channels, shale channels and pyritic-rich, green claystones were encountered on both sides of the mains, and which impacted both development and longwall ground control. In particular, poor transitional roof areas near the edges of the sandstone and shale channels often posed significant ground control challenges. In addition, hydraulic fracturing was sometimes utilized to enhance caving of massive sandstone behind the shields to relieve pressure at the face. Longwall face conditions and advance rates were documented to illustrate the effects of sandstone channels, shale channels, and green claystones on safety and productivity and to demonstrate the effectiveness of the hydraulic fracturing.Shale channels, slickensided zones, laminated roof zones, soft floor, and a regional syncline were encountered in Mine C, the combination of which posed unique ground control challenges during both development and longwall mining. The presence of soft floor, coupled with the presence of thick floor coal and deep cover, resulted in headgate convergence during retreat of the first right-hand longwall panel. Two-piece 8-foot bolts were sometimes observed to fail at the coupler within the laminated roof zone, and 6-foot, 1-piece, fully-grouted point-anchor bolts were employed as the primary bolts thereafter."

Jan 1, 2015

By Jeff Whyatt

Deformation of underground salt, trona and potash mines is generally time dependent, providing for gradual adjustment of strata to mining induced stresses. Time dependence can allow for higher extraction ratios provided eventual failure can be tolerated. However, this eventual failure can be violent if creep deformation can shift stress and potential energy to strong, brittle geologic units. The mine failure case studies reviewed here illustrate this process. Yield pillars and defects in bridging strata figure prominently in these cases. Yield pillars provide local and temporary support to the roof, temporarily delaying the cave; and allowing extraction ratios and overburden spans to increase beyond the long term capacity of overlying strata. Defects (faults, voids, thinning) of strong overburden strata reduce the critical span, sometimes to less than panel width. Analyses of many of these cases have focused on a cascading pillar failure mechanism, but recent work and this review point to failure of strong overburden strata as the essential element. The suddenness of failure and attendant seismic events pose hazards to miners and, in some cases, to those on the surface. Characterizing these failures is a first step towards recognizing and managing the risk of catastrophic collapse in underground mines.

Jan 1, 2008

By A. T. Iannacchione

Numerical simulation of coal pi1lar loading has traditionally been a difficult task due to the unique and highly variable properties of coal and the inability of numerical procedures to duplicate these properties. This simulation was based upon material properties developed from laboratory tests of coal cubes and examined against coal pillar strength data developed from actual underground measurements. The coal cube measurements indicated the coal followed a nonlinear Mohr- Coulomb failure criterion. The in situ measurements showed that a pillar yield zone developed similar to Wilson's hypothesis and, at high confinements, the pillar core seemed to followed a pseudo-ductile behavior. The strain-softening material model, based on a 1inear Mohr- Coulomb failure criterion, simulated coal cube and pillar behavior at moderate load conditions. However, at high loads the models were inaccurate, due to an inadequate failure mechanism and/or to changes in the pillar constraints at the coalbed interface.

Jan 1, 1989

By Stephen C. Tadolini, John Bolton, Bre-Anne Sainsbury, Tom Meikle

"The capacity of ground support components which have been affected by corrosion is reduced and may ultimately lead to dynamic failure of the component and the strata. In order to maintain an effective, long-term ground support system, significant campaigns of rehabilitation are often required in corrosion affected areas which also expose the workers to hazardous conditions. The most common corrosion protection for steel ground support utilises sacrificial systems such as galvanising. Galvanising has previously been proven to be susceptible to some corrosion processes. Stainless steel is the most effective in resistance to corrosion, but can be cost prohibitive, and its mechanical properties often make it unsuited to use in ground support components.Providing an outer protective plastic coating to bolts has proven to be an effective means of protecting the inner steel bar from corrosion. However, these support systems tend to be susceptible to coating damage, and require post cement grouting to provide full encapsulation. In comparison to a standard bolt/resin system, they can be slow to install and expensive. These systems have also been shown to reduce overall load transfer performance of the bolting system.In order provide a higher level of corrosion protection whilst maintaining current installation practices and bolting cycle times, Minova has developed the Enduro™ Steel Ground Support Range. The Enduro™ range consists of standard Minova steel ground support components which have been treated with a unique coating process. The Enduro™ coating has been tested in the harshest of conditions, in laboratory controlled conditions and in underground trials. It has been proven to effectively resist or completely eliminate the formation of corrosion, even in the most aggressive environments. This paper explains the process and provides the details of the laboratory and underground corrosion performance testing carried out on Enduro™ ground support products.INTRODUCTIONTraditionally, the most common form of corrosion protection in steel ground support consists of a sacrificial protective coating such as galvanising (Aziz, et al., 2013). Such coatings have proven to be ineffective in extreme high and low pH conditions with corrosion of the support system commonly encountered. There is also evidence that common forms of galvanising may actually increase the rate of corrosion in certain pH environments. Figure 1 shows typical corrosion and failure of a standard re-bar roof bolt."

Jan 1, 2016

By Yoginder P. Chugh

Subsidence may be observed above partial extraction shallow room-and-pillar mines where the coal seam(s) is associated with weak and thick claystone in the floor. This paper presents results of subsidence studies at such a mine. During the 26-month study period, a time dependent subsidence causing a maximum vertical movement of 50 mn was observed. After a subsidence rate of 6.0-6.5 m/month for the first two months after development of mine workings, the rate decreased to 0.8-0.9 mm/month after 17 months. However, presumably due to settlement of barrier pillars, it increased therafter to 1.7 mm/month for the next 9 months. Angle of draw, based on zero subsidence, was calculated to be about 29 degrees. Maximum tensile strain and compressive strain values observed were 0.040 pct and 0.039 pct respectively. A hypothesis was fomlated to correlate surface subsidence movements with observed underground movments. The data collected to date fits reasonably well within the formulated hypothesis.

Jan 1, 1989

Historically, the selection of mining sequence for multiple seam conditions has been based on many factors other than ground control considerations and minimization of interaction effects. Today, numerous operations are finding themselves mining above existing or abandoned operations, some of which exhibit large scale caving, pressure arches and subsidence troughs. Development of design criteria for the upper seam that would alleviate damage due to lower seam interaction effects can contribute substantially to the safety and productivity of many mining operations. The primary objective of this re search has been to identify methods of improving ground control conditions in the upper seam when mining through either passive or active subsidence waves. These methods concentrate on improved ground control practices for the upper seam, rather than reducing the amount of subsidence in the upper seams by improved practices in the lower seam. Design factors such as pillar size, pillar and opening orientation relative to the subsidence trough, offsetting intersections, and different support methods have been studied for the upper seam in a variety of typical geologic environments. Analysis has demonstrated criteria for ameliorating negative interaction effects and facillitating design in the superincumbent seam.

Jan 1, 1986

By Andre Zingano

The objective of this paper is to compare the behaviors of different types of roof bolts: (1) One-Step Bolt (OSB), (2) Fully grouted Bolt (RB), (3) Combination Bolt (CB), and (4) Torque tension Bolt (TB). Two dimensional numerical models were built for both bolted and unbolted roofs. The geological sequence and rock properties used in the numerical models represent the typical roof condition for Pittsburgh coal seam. Using the unbolted roof as a base case, a comparison is conducted by monitoring the roof vertical displacement at the center of the entry and at the bolt positions, the axial force in the roof bolts, and stress distribution in the bolted area. The grout/rock interface is assumed to be perfect. The estimated roof displacements showed that the differences among the four types of roof bolts are small. The major differences are in the shear stress at the grout/rock contact and in the shear stress along the immediate roof bedding interface as well as in the bolt axial stress. There is less axial stress for the OSB compared to RB and CB as the diameter of the OSB is much bigger and the contact area between grout and rock is twice as large as for RB and CB. The higher strength of the OSB contributes to keep the bedding planes in the roof closed.

Jan 1, 2007

By John Ellenberger

The nature of a stone deposit is rarely defined through exploration and engineering design, but more through the actual experience encountered as the mine develops; hence, issues with ground control are often at the forefront for a new mine. Ground control problems account for over 15 percent of lost-time injuries in underground stone mines. The objective of this work is to present actions taken during early development of a stone mine to mitigate the obvious effects of high horizontal stress on ground control. The mine was developed from a box cut with relatively little cover, and high horizontal stresses were not anticipated. Early recognition of possible high horizontal stress resulted in mapping of the mine using the NIOSH-developed Roof Fall Risk Index (RFRI) to provide a baseline to objectively analyze roof conditions. A program of borescoping the mine roof provided valuable roof beam thickness data and found that the roof beam was of minimal thickness, approximately 10 percent of drift width. As the mine developed, it became apparent that ground control problems related to high horizontal stress existed. A concentrated effort was made to improve ground conditions by implemeting a number of mitigation techniques. Actions taken by the mine included systematic roof support, reorientation of mining direction, a lower roof horizon, reduced span widths and reduced mining height in crosscuts to prevent running falls. These strategies resulted in signifcantly improved ground stability.

Jan 1, 2012