Search Documents

By Carl Havemann

[PAPER PRESENTED AT THE 8thINTERNATIONAL CORROSION CONFERENCE HELD AT THE SA NATIONAL MUSEUM OF MILITARY HISTORY, SAXONWOLD JOHANNESBURG DURING 14-15 NOVEMBER, 2006.]

Jan 1, 2006

By N. A. Sithole, S. A. C. Hockaday, P. J. A. Bezuidenhout

The Northern Cape Province in South Africa has high levels of annual direct normal solar irradiance and reserves of zinc (Zn) ores. The question arises as to the benefits of integrating renewable solar energy into the beneficiation routes of these reserves. The paper evaluates a novel flowsheet for the production and beneficiation of Zn in this region, maximising localised solar energy as a source for both electricity and process heat. Solar variability is discussed and the cost and benefits of thermal storage in the flowsheets are evaluated by its influence on the levelised costs of electricity and process energy over the project life-time at a possible implementation site. The results of the developed scoping model showed that solar photovoltaic integration to provide electricity for electrowinning without battery storage can lead to more than 10% cost saving on electricity over the lifetime of the project. Additional savings potential was identified when battery storage was included to enable the solar PV system to supply electricity during peak tariff periods. The solar thermal case showed the most promise with savings of 70% on heating costs for casting, while solar PV electricity without storage resulted in a 16% cost saving on heating for casting over the lifetime of the project. Solar PV electricity generation resulted in the avoidance of more than 20% of CO2 emissions from grid electricity use. Solar thermal heating can avoid up to 80% of the CO2 emissions associated with grid electricity use for remelting of Zn cathodes for casting. The CO2 emissions are indirect and not subject to South African carbon tax. Keywords: Solar process energy, zinc beneficiation, flowsheet evaluation

Jan 1, 2020

By R. Ribacchi, P. Tommasi, C. Consorti, P. Campedel

The runout of dry blocky rock avalanches produced by planar rockslides affecting a limestone formation with clayey interbeds is analysed by means of distinct element modelling. Numerical analyses are validated by means of the back analysis of a historical rockslide occurred in the investigated area and physical aspects of the phenomenon evidenced by modelling are discussed. On analyse par la méthode aux élements distincts la distance de parcours des avalanches rocheuses sèches produites par des glissements plan interessant une formation de calcaire à intercalaires argilleux. Les analyses numeriques sont validées à l’aide de la back-analysis d’un glissement historique survenue dans le site en examen. On décrit les aspects physiques su phénomène mis en évidence par la modélisation efféctuée. In diesem Beitrag wird die Reichweite von Steinlawinen besthend aus trockenem blockhaftem Fels mittels der Distinct Element Methode untersucht. Die Steinlawinen werden erzeugt von Rutschungen in einer Kalkstein-Formation mit tonhaltige Schichten betreffen. Die numerischen Berechnungen wurden anhand einer Simulation einer historischen Bergsturzen verifiziert, der sich auf den untersuchten Gebiet ereignete. Auf der Basis der erhaltenen Ergebnisse wurden die physikalischen Aspekte der untersuchten Steinlawinen analysiert.

Jan 1, 2003

By Merete Tangstad, Kai Tang

The primary aim of the present investigation is to develop a model which permits to calculate/predict the viscosities of ferromanganese slags, typically focus on the MnO-SiO2-Al2O3-CaO-MgO-FeO multicomponent system. The present viscosity model emphasizes the ability of prediction, i.e. using the binary parameters to extrapolate the viscosities in ternary and higher order systems. To this end, a physical sound model is essential. Temperature dependence of viscosity is described by the Eyring?s formalism. The well-known cell model is used to define the SiO44- tetrahedra in the silicate melts. Composition dependence is expressed in term of viscous activation energy, which is characterized by the binary structural units. The viscosities in ternary and higher order systems are hence predicted using the binary activation parameters. The model has been used to calculate the viscosities in the whole liquid composition range of ferromanganese slag.

Jan 1, 2007

By A. Golshani, M. Oda, K. Suzuki, T. Takemura

Anisotropic behaviours of OhshimaOshima granite were investigated by carrying out uniaxial compression tests, together with observations of microcracks under an optical microscope. The elastic modulus tensor of Oshima granite at 10 per cent strength,E10, were calculated using theoretically formulation of elastic modulus tensor in terms of the second-rank crack tensor for pre-existing open microcracks. Furthermore, with the assumption of orthorhombic elasticity, the nine moduli of Oshima granite E10were determined by uniaxial compression test. Twenty-onemoduli of samples, calculated without assuming any symmetry, also showed orthorhombic features. Direction of the symmetry axes agreed well with the orientation of preexisting cracks. Comparison of crack tensor-based formulation results with the experimentally determined one show that the anisotropy of elasticity of Oshima granite is caused by pre-existing open microcracks, not by pre-existing healed microcracks and also crack tensor formulation can be used, as a first-order approximation at least, to describe the anisotropy of Oshima granite induced by pre-existing open microcracks. ZUSAMMENFASSUNG: Das anisotrope Verhalten des Oshima-Granits wurde mit Hilfe voneinachsigen Kompressionstests und durch die Betrachtung von Mikrorissen unter einem optischenLichtmikroskop untersucht. Das Elastizitätsmodul von Oshima-Granit bei 10 Prozent Kraft E10wurde berechnet, indem man die Formulierung des Elastizitätsmodultensors, ausgedrückt alsRisstensor zweiter Ordnung theoretisch auf bereits existierende Mikrorisse angewandt hat.Außerdem wurden die neun Module des Oshima-Granits unter der Annahme orthorhombischerElastizität E10mit einem einachsigen Kompressionstest bestimmt. Einundzwanzig Stichproben,die ohne die Annahme irgendeiner Symmetrie genommen wurden, zeigten ebenfallsorthorhombische Merkmale. Die Richtung der Symmetrieachsen stimmte mit der Orientierungbereits vorhandener Risse überein. Der Vergleich der Ergebnisse der auf dem Risstensorbasierenden Formulierung mit der experimentell bestimmten Formulierung zeigt, dass dieAnisotropie der Elastizität von Oshima-Granit von bereits vorhandenen offenen Mikrorissenverursacht wird, und nicht von vorhandenen vernarbten Mikrorissen, und dass dieRisstensorformulierung auch zumindest für eine Annäherung erster Ordnung benutzt werdenkann, um die durch vorhandene offene Mikrorisse induzierte Anisotropie des Oshima-Granits zubeschreiben. RESUME: Les comportements anisotropes du granit d’Oshima ont été étudiés en réalisant destests de compression simple, et en observant les microfissures au microscope optique. Le tenseurdu module d’élasticité du granit d’Oshima sous une résistance de 10 pourcents, E10, a été calculéen se servant de la formule théorique du tenseur de module d’élasticité basé sur le tenseur defissures de second ordre des microfissures ouvertes préexistantes. En outre, sur base del’hypothèse de l’élasticité orthorhombique, les neuf modules du granit d’Oshima ont étédéterminés par des tests de compression simple. Vingt et un modules d’échantillons, calculés endehors de toute hypothèse de symétrie, ont aussi montré des caractéristiques orthorhombiques. Ladirection des axes de symétrie correspondait bien à l’orientation des fissures préexistantes. Lacomparaison des résultats de la formule basée sur le tenseur de fissures avec les résultatsdéterminés expérimentalement montrent que l’anisotropie de l’élasticité du granit d’Oshimaprovient des microfissures ouvertes préexistantes, et non de microfissures préexistantes referméeset que la formule du tenseur de fissures peut servir, au moins comme première approximation, àdécrire l’anisotropie du granit d’Oshima marqué par des microfissures ouvertes préexistantes.

Jan 1, 2003

By deur J. V. D. M. Grimes

Sishen Iron Ore Mine is one of the largest open-pit mines in the world, and loading and hauling constitutes one of the major cost items on the mine. Because high productivity in loading and hauling results in large financial benefits, the following projects to improve productivity were implemented at Sishen: - a computerized truck-allocation system, - an overhead power-supply system for the dieselelectric driven rear-dump trucks, - an in-pit crusher and a belt-conveyor system. This paper concentrates on the truck-allocation system, with special reference to the improved productivity of loading and hauling resulting from the implementation of this system.

Jan 1, 1984

By Haiping Sun, Samir Ganguly, Oleg Ostrovski, M. Yaser Lone

Wettability of graphite by synthetic SiO2-Al2O3-CaO-MnO slags with varied MnO content and by industrial slags was studied at 1350-1600 °C using sessile drop method under argon atmosphere. Initial contact angle was the lowest (110-115o) for the MnO-free slag. For slags with 10-40 wt% MnO, the initial contact angle was in the range 125-135o. The contact angle decreased with the contact time. The change in the contact angle with slag mass was found insignificant. The surface tension of slags obtained from the drop shape analyses was 500-800 mN/m and varied in a narrow range with temperature and MnO concentration. The reduction rate increased with increasing MnO content in the synthetic slag from 20 wt% to 40wt% and temperature. Increasing temperature also increased the rate of reduction. No correlation was observed between the reduction rate and MnO content in the synthetic slags in the range 0-20 wt% and in the industrial slags. The rate of SiO2 reduction from the molten slag was close to the rate of MnO reduction. The MnO-free slag had the largest contact area with graphite substrate. Keywords: reduction, wettability, graphite, slag, manganese, surface tension.

Jan 1, 2007

By J. Engels

CODELCO is considering the implementation of high-density tailings management at the Chuquicamata mine in northern Chile for its long term disposal plan. To achieve this, CODELCO commissioned the design, construction, and operation of a 70 t/d pilot plant, fed by existing tailings. The testing programme was completed in May 2011, and consisted of laboratory rheological and characterization assessments, pipe loop testing, beaching trials, and analyses of deposition behaviour for solid contents ranging from 57?68% (w/w). This paper describes the characteristics of the pilot plant, the testing programme, the beach trial analyses, and the resulting beach profile predictions based on the stream power theory. CODELCO also used other predictive beach slope methods, such as the equilibrium slope concept, which are not discussed in this paper. The final beach profile for design will be selected after an expert analysis of all methods has been completed.

Jan 1, 2012

By C. Sarkar

Increased competition in today’s global economy has put mineral industry under excessive pressure to effectively manage production assets to generate business wealth. Capital intensive industry (CII) organizations are seeking ways to manage skill resources, internal processes, and organizational networks with a view to reduce the cost of ownership of assets and increase efficiency of operations and service. The emerging concept of Enterprise Asset Management(EAM) is a collection of business processes that allow CII with right focus on return on investment on assets, to make right decisions on planning, acquisition, maintenance, operation, rehabilitation, and disposal of assets. Information technology (IT) can drive significant returns if the infrastructure covers seamlessly all business processes and all systems, like geographic information system, maintenance management, investment management, laboratory information management, and supervisory control and data acquisition system. The simple approach to IT in the past with disconnected silos of technology, information, and business processes cannot deliver the expected benefits under the modern business environment. Identification of business and application component is a prerequisite for the development of an asset management system that links effectively disciplined processes having characteristics of agility, speed, and integration. This paper discusses various issues and outlines the steps for developing an asset management roadmap in an organizsation. It also presents major business and application components of the system. Keywords: Enterprise asset management, Business architecture, Business component, Application component, Asset ownership, Asset operations, Information technology, Capital Intensive industry

Jan 1, 2003

The paper examines the design issues associated with the integration of mineral processing within underground mining systems. It demonstrates conceptual integrated system design options appropriate to a range of geological scenarios. Particular reference is then given to a case study of stoping in narrow base metal veins. The performance of such integrated systems in terms of productivity, economic and environmental criteria is demonstrated by means of simulation. Particular attention is given to the potential benefits to mine waste management. Processing technologies appear to offer genuine potential benefit, whilst underground mining methods may need to evolve further to facilitate full integration. This paper is based on industry supported research aimed at developing selective and clean underground mining systems.

Jan 1, 2003

By J. He

The separation performance of a raw coal sample from South Africa based on the dense gas-solid fluidized bed beneficiation technique was investigated. Analysis showed that the raw coal sample distributes mainly in the -50+6 mm size range with the -1.6 g/cm3 density fraction accounting for 78.20% of the cumulative mass distribution. A flow sheet of the sequential coal beneficiation technique was introduced. The experimental and simulation results of the hydromechanical and density distribution stability indicate that the dense gas-solid fluidized bed could provide a stable separation environment with uniform density fluctuations under suitable operating conditions. With the application of this technique on the raw coal sample, the separation results show that three products, consisting of 73.25% clean coal with an ash content of 9.59%, 11.31% middlings, and 15.44% gangue were effectively separated at two different densities of 1.82 g/cm3 and 1.57 g/cm3. This study provides an effective flow sheet for achieving the high-efficiency separation performance on raw coal from arid areas. Keywords dense gas-solid fluidized bed, dry coal beneficiation, density distribution, separation efficiency.

Jul 1, 2013

By A. P. I. Popoola

Laser coatings are used for a wide variety of applications. TiB2/Ni intermetallic matrix composite coatings were fabricated on Al-substrate by a high power Rofin Sinar Nd: YAG solid-state laser. The characterization of the coatings was carried out by optical microscopy (OM), scanning electron microscopy (SEM/EDS) and X-ray Diffraction (XRD). Electrochemical study of the laser coatings in 3.65 per cent NaCl at room temperature revealed that with very high weight proportion of nickel the corrosion resistance of the coatings deteriorated due the presence of AlB10 phase. 50 wt per cent TiB2+50 wt per cent Ni laser coatings exhibited the highest corrosion resistance in test solution. Keywords Corrosion, protective film, laser surface alloying, reinforcement.

Jan 1, 2011

By W. D. Northrop

This paper gives an account of the development of a technique whereby the vertical limits of geological horizons may be identified by the use of vertical variograms on the mineral of economic interest. This information may supplement or guide the correct subdivision of the individual horizons into meaning full data sets by diligent geological observation. This process then improves the quality of the variance modelling of the gold distribution in the plane of the individual layers and therefore enables better estimates to be made into the grids or blocks of the mine model. The technique is explained by an account of the development work, which was performed, on duplicate superimposed reef horizons in the Kimberley formations. The paper then shows how the correct approach was developed to evaluate the mineralized layers in a multiple stacked conglomerate layer sequence in the Elsburg reefs of the Witwatersrand Rand System at the Target deposit. The method of categorization of resources according to confidence in the estimate is also explained. The feasibility processes carried out on the three-dimensional model, in accordance with the SAMREC code are also described. An example of the development of a reconciliation process utilizing chip sampling is also explained.

Jan 1, 2003

By M. Gous

Keywords: Pyrometallurgy, Namakwa Sands, ilmenite, DC arc furnace, titania slag, pig iron Namakwa Sands is a heavy minerals mining and beneficiation business in the Anglo Base Metals Division, and operates along the West Coast of South Africa. The business encompasses mining, mineral concentration, separation, and smelting operations. The smelting process comprises the carbonaceous reduction of ilmenite to produce titania slag with a TiO2 content of 86%, and iron with a carbon content of 2.5%. The Namakwa Sands smelter, situated near the Saldanha Bay harbour, commenced smelting operations in 1994, when a 25 MW DC arc furnace was commissioned. The smelting operations were expanded in 1999, with the commissioning of a second 35 MW DC arc furnace. Despite the fact that ilmenite smelting poses a technical challenge in terms of the high temperatures required, the physical characteristics of the slag, the constraints placed on the feedstock, and the tight product specifications, Namakwa Sands has continually increased slag production since 1995. High furnace feed-on utilisation and furnace stability, complemented by continuous improvement drives, will be the vehicle to drive performance in the short term, with longer-term performance enhancements due to strategic process development.

Jan 1, 2006

By R. C. D. Phillis

The management of critical resource inventories is an important productivity lever and a significant risk factor?risk in the sense that poor resource availability lends itself to disempowerment of workers, unsafe work practices, wasted spending (high unit costs),and poor quality of work (including mining waste/rework). Most underground platinum mines experience lost blasts that directly lead to reduced productivity. In most surveyed shafts, 30% of lost blasts can be attributed to shortages of critical material and/or equipment. The problem is prevalent despite the existence of conventional transitory surface and underground stores. This paper discusses the introduction of buffer stores as a complementary materials storage system in order to improve health and safety in mines as well as reduce lost blasts. Both quantitative and qualitative results have shown that buffer stores result in dramatic improvements in productivity and are readily acceptable by stakeholders. Keywords Buffer stores, lost blast.

Jan 1, 2011

By R. Dippenaar

The emergence of new steel grades is largely driven by the need to produce high quality steel at a competitive price. The principal aims are to attain ultra-high purity, (especially low interstitial elements) and ultra-cleanliness (by the control of the inclusion content and size). Whereas the steel used to build the Titanic contained 650 ppm sulphur, resulting in MnS stringer-inclusions 25 mm in length, modern quality requirements for arctic pipelines would only allow 10 ppm of sulphur and inclusions in ball-bearing steels must be smaller than 5µm. Most developments are aimed at hot-metal treatment before refining and ladle treatment after decarburisation. Because ferroalloys are added during or after the refining step, it is the secondary (ladle) refining production technologies that are of specific interest to the ferroalloy producer. Through ladle treatment, hydrogen and nitrogen contents are reduced, ultra-low levels of solute impurities are attained and the shapes as well as the composition of inclusions are modified. Steelmakers are concerned about the cost effectiveness of the use of ferroalloys such as consistent product analysis and delivery, improved financing arrangements and technical support. Minimal variation in product sizing is vital because it impacts on handling problems and because particle size determines the rate of particle dissolution. The required ferroalloy product quality depends on the specific use but in general sulphur, phosphorous and nitrogen contents are of concern. Apart from the presence of trace and impurity elements, ferroalloys also contain inclusions. For example, ferromanganese may contain MnO-MnS-SiO2 inclusions while high-carbon ferro-chrome may contain different kinds of Cr-Mn-spinels. The presence of these impurities and inclusions has a significant impact on steel production techniques and cost and hence, on the selection and use of ferroalloys. The interrelationship between ferroalloy quality and steel production technology is plant and product specific and hence, effective communication between ferroalloy suppliers and steel producers is essential.

Jan 1, 2004

By O. Nyandoro, K. Khoza-Shangase, M. Madahana, N. Moroe

"Occupational noise-induced hearing loss (ONIHL) is classified as the leading work-related disability in the mining industry. ONIHL has a negative impact, on not only the health and occupational productivity of affected individuals, but arguably also on the country’s mining industry and economy. Hearing conservation programmes (HCPs) are an effective strategy in the management of ONIHL. However, current literature indicates that HCPs are not achieving the anticipated and desired outcomes in the South African mining sector despite the efforts focused on the management of ONIHL. Therefore, the purpose of this study is to propose the use of a feedback-based noise monitoring model as a tool for monitoring and managing ONIHL in the South Africa’s mining sector. This model is a basic static feedback model with practical applications such as estimating, monitoring. and providing quantitative information to aid miners, mining administrators, and policy-makers in decision-making around HCPs. Additionally, the model could form part of an early intervention and management strategy for ONIHL in the workplace. The strength of this model, although currently static, is that it encompasses all the pillars of HCPs and takes into account the policies concerned with the management of ONIHL in the mining sector. IntroductionHazardous noise levels (above 85 dBA) in the workplace place exposed employees at risk of developing a disabling occupational noise-induced hearing loss (ONIHL). ONIHL is the ‘partial or complete hearing loss in one or both ears as a result of one’s employment’ (Nandi and Dhatrak, 2008, p. 1). This type of hearing loss develops gradually as a result of being exposed to continuous or intermittent high levels of noise over a long period of time (McBride, 2004; Patel et al., 2010; Rappaport and Provencal, 2001). A hearing threshold below 40 dBs is classified as a disabling hearing loss (Yadav et al., 2015), resulting in a hidden condition that does not readily manifest itself (Tye-Murray, 2009, p. 3). Dugan (2003) describes disabling hearing loss as the ‘most prevalent, least recognized and least understood physical disability’, while Copley and Frederichs (2010) and Hermanus (2007) argue that permanent disabling hearing loss is a major contributor to the global burden of disease on individuals, families, communities, and countries."

Jul 1, 2019

By D. P. Roberts

This investigation aimed to simulate the experiments performed by Nic Gay (Gay, N.C. 1976. Fracture growth around openings in large blocks of rock subjected to uniaxial and biaxial compression. International Journal of Rock Mechanics and Minining Sciences and Geomechical Abstracts, vol. 13. pp. 231-243) on fracture growth around openings in blocks of rock subjected to uniaxial and biaxial compression, using the Elfen discrete element code. The results of the physical experiments indicated a number of trends that were successfully replicated in the numerical simulations, including crushing ahead of the face, the formation of a sub-vertical tensile fracture at centre-span, the formation of groups of fractures originating from the crushed face zone, the formation of large corner-to-corner fractures which precede sample failure, and linking of slot corner and sample corner fractures leading to sample failure. In addition, other features were apparent that were not reported by Gay. It is believed that these took the form of conjugate shear fractures (as reported by Gay in a previous paper) and other features that may have been altered or inhibited by the presence of pre-existing structure in the physical samples. It was found that the samples, though nominally made up of the same rock type, must have had significantly differing properties. The presence of pre-existing structures may have contributed to this discrepancy. Strain measurements from the physical experiments were reasonably well matched, except where the gauge lay directly in the path of advancing fractures.

Jan 1, 2012

By N. Kumar, A. K. Dhawan, A. Varughese, S. K. Khullar

Abstract The in-situ stress field is one of the primary parameters influencing the performance of underground structures particularly in the Himalayas where there is strong influence of topography and geology on in-situ stresses. It is always advisable to measure the in-situ stresses, in whatever best way possible. Hydrofracturing is one of the methods by which in-situ stress can be measured. This paper briefly describes details of the concept of Hydrofracturing in arriving at the in-situ stresses of the rock mass at Pancheswar Project. The data obtained from the tests has been analysed, interpreted and the results are presented in this paper. Kurzfassung Das Spannungsfeld an Ort und Stelle ist einer der wichtigsten Parameter, die das Verhalten der Untergrund-Struktur beeinflussen, insbesondere in den Himalayas, wo die Topografie und die Geologie einen grossen Einfluss auf die oertlichen Spannungen ausueben. Es empfiehlt sich stets die Spannungen an Ort und Stelle so gut wie moeglich zu erfassen. Die Hydrofraktur bzw hydrografisches Zerstueckeln ist eine der Methoden, die bei den Messungen der oertlichen Spannungen verwendet werden koennen. Diese Abhandlung beschreibt kurz Einzelheiten ueber das Konzept von Hydrofraktur bei der Bestimmung der Spannungen an Ort und Stelle von der Felsmasse bezueglich des Projekts Pancheshwar. Die gewonnenen Daten aus den Messungen wurden analysieret und ausgewertet. Die Ergebnisse werden dabei vorgelegt. Sommaire Le champ de contraintes in-situ est un des paramèters principaux influencant l’exécution des structures souterraines particulierèment en Himalaya où les forces in-situ sont fortement influencées par les caractéristiques topographiques et géologiques de la région. La fracturation hydraulique est une technique qui permet de mesurer des forces in-situ des massifs rocheux. Cet article décrit brièvement le mécanisme de fracturation hydraulique et présente les résultats de mesure des forces in-situ des roches au site du projet hydroélectrique de Pancheswar.

Jan 1, 2003

By P. J. Bhonde, R. D. Angal, R. H. Tupkary

Manganese imparts numerous beneficial mechanical properties. Hence it finds extensive application in iron, steel and non-ferrous sector. Prevalently, it is incorporated in the form of master alloys i.e. 'ferromanganese'. In India, ferromanganese is mainly the inexpensive and paramount source of availability of manganese. Various conventional and non-conventional techniques of ferromanganese production have been adopted in past and present. However, these techniques have demerits viz. high refractory, energy consumption, losses of valuables in slag and fumes. Also geographical co-ordinates of the plant restricted the manufacturer to prefer an appropriate process. Accordingly, the industrially implemented methods had reliance on availability of infrastructure, energy, mineral resources, grade of raw material, outlay of labor, environmental compatibility of technique etc. In view of the liberalized economy and the gap scenario in the supply and demand of ferromanganese, the authors felt it indispensable to explicitly bridge up this vacuum by initially designing a simple energy conserving, eco-friendly, low capital investment technique for decarburization of ferromanganese. Measurement of the data involved studying the impact of rate governing parameters on the process kinetics. This laboratory scale investigation is expected to escalate the Mn/C quotient of high carbon ferromanganese. Key Words: ferromanganese, carbon, carbide, decarburization, rate, kinetic

Jan 1, 2007