Search Documents

By A. Boniface

The International Tunnel and Underground Space Association (ITA) has a number of working groups (WG) that meet at least once a year. One of these is WG12, ?Use of Shotcrete?, of which the author is a member. The purpose of this paper is to draw attention to a number of topics that were discussed at the WG12 meetings held in April and September 2008; and also to a number of other matters that arose from the presentation of thirty-four papers at the 5th International Symposium on Sprayed Concrete held in Lillehammer, Norway between 21 and 24 April 2008.

Jan 1, 2008

Splashing and wave formation has been studied experimentally by using one-seventh water model of CLU (Creusot-Loire Uddeholm) reactor with two different tuyere configurations by using paraffin and water as simulated slag and simulated metal respectively. Experimental results have been discussed in terms of total splash volume, relative slag volume in splash (dispersed-slag phase holdup in splash), wave frequency and wave amplitude with respect to gas injection rate and tuyere configuration at bath heights between 0.25m and 0.38m. Gas flow rates ranged from 0.00599m3/s to 0.01312 m3/s. The results of splash measurements showed that splash volume increased with increasing gas flow rate and decreasing bath heights for both tuyere arrangements. However, off-centre configuration resulted in relatively higher amounts of splash. The slag volume in splash (Dph in splash) was also found to increase with decreasing bath heights and increasing gas injection rates. The high speed photography revealed that the frequency and wave amplitude increased with gas injection rate. The experimental results also showed that the frequency and vertical displacement of the rotating wave increased when the tuyere orientation became off-centered. This might be used to explain why off-center configuration resulted in generating higher splash volumes than the center configuration.

Jan 1, 2004

By M. Castelli, C. Scavia, S. Marello, A. Allodi

ABSTRACT – This paper investigates the possibility of interpreting the shear band evolution in hard soils and soft rocks as the result of shear propagation from pre-existing natural defects. Thesis done through the application of the principles of Fracture Mechanics, a Slip-Weakening Model(SWM) being used to simulate the non-linear zone at the tips of the discontinuity. Experimental observations have been carried out on prismatic samples of Beaucaire marl through biaxial compression tests in plane strain conditions. A numerical simulation confirms the validity of the proposed approach. RÉSUMÉ – Cet article présente la possibilité d’interpréter l’évolution des bandes de cisaillement dans les roches tendres et les sols raides comme le résultat de la propagation pour cisaillement à partir d’un défaut préexistant. Le Slip-Weakening Model (SWM) a été employé pour modéliser la zone non linéaire a l’extrémité d’une discontinuité. Nous présentons des observations expérimentaux obtenues à travers des essais de compression en déformation plane sur des échantillons prismatiques de marne. La simulation numérique d’un essai confirme la validité de la méthode proposée. KURZFASSUNG – Die vorliegende Arbeit versucht die Ausbreitung von Scherzonen in(bindigen) Böden und im Lockergestein anhand der Entwicklung von Scherrissen ausgehend vonexistierenden Schwachstellen zu erklären. Die Umsetzung erfolgte mit Hilfe der Bruchmechanik,für die Modellierung der nichtlinearen Zone an den Rissenden wurde ein Slip-Weakening-Modell(SWM) eingesetzt. Es wurden zweiaxiale Druckversuche an prismatischen Probekörpern vonBeaucaire Mergel unter der Bedingung eines ebenen Verzerrungszustandes durchgeführt. Dienumerische Untersuchungen bestätigten die Annahmen der untersuchten Theorie.

Jan 1, 2003

Beatrix Gold Mine, a deep-level gold mine in the Free State province of South Africa, has the highest methane emission rate of any gold mine in the country. Methane is emitted from underground sources intersected during mining operations and is liberated into the general mine atmosphere. The total methane emission rate for the mine is of the order of 16001/s and the South section of the mine emits approximately 10001/s of methane gas. The mine has a history of gas accumulations which have led to a number of underground explosions. Following the last explosion in 2001 and the subsequent investigation, a number of recommendations were made. Two of these were to consider extracting the underground mine methane to render the mine atmosphere safe, and to declare hazardous locations that require special operating procedures. A number of such workplaces have now been declared at the South section of the mine. Methane gas is a potent, explosive greenhouse gas whose contribution to global warming and climate change is 21 times higher than that of carbon dioxide. To reduce its inherent danger and to mitigate its global warming impact, a carbon credit project under the Clean Development Mechanism (CDM) of the Kyoto Protocol has been developed and implemented, the aim being to capture and destroy the methane at Beatrix mine. The mine has constructed an extraction system to capture and extract 400 (Is of the methane. Percentage methane (per volume) of the gas intersected at source is 85%, with negligible concentrations of other hydrocarbons and water associated. The mine contracted the services of Group Five to design and construct the flare and ancillary equipment on surface, and Promethium Carbon was contracted to assist with the carbon¬-related aspects, approval framework, and administration of the project. A number of design and construction challenges had to be faced to extract and transport the gas effectively to the surface of the mine as the emitters are approximately 3 600 m away from the mine shaft at a depth of 860 m. Further considerations were the requirements for the type of column to be used to transport the methane gas, the pressure loss over the system, the safety systems needed to address the risk factors involved in the transport of the methane gas, and a suitable pumping system to extract the gas to the surface. The system operates under negative pressure provided by two blowers on surface delivering the emissions to a flare capable of burning off 450 8/s of methane gas. In this paper a number of benefits for the mine are discussed. These include, but are not limited to, the removal of approximately 55% of the total volume of methane gas from the general body of the air in the geographical areas of the mine where the methane gas is emitted into the atmosphere, and reducing the risk of methane-related incidents. A further benefit of this project is the mitigation of the global warming impact of the methane gas and the reduction of the mine's carbon footprint by approximately 25%. This project could also assist in alleviating the energy shortage being experienced in South Africa by means of the planned generation of 4 MW of electrical power, utilizing the methane gas, as a second phase of the project.

Jan 1, 2011

By T. Gerritsen, R. C. Delgado, J. Janzen, E. R. Veloza

The paper describes the components of an Integrated Furnace Control system for covered-arc (shielded arc) smelting with results from the recently started 75 MW Cerro Matoso Line 2 Furnace. The paper starts with a review of the mechanisms of power and feed input and heat losses in the shielded-arc smelting process, and describes how the details of the control system are tailored to the process. The control modules of a covered-arc smelting furnace are described including measured results and screen captures. This paper focuses on Integrated Furnace Controls tailored to shielded-arc smelting, but similar approaches have been recently applied to other furnace processes including immersed-arc smelting.

Jan 1, 2004

By A. Kazemi, M. A. Ahmadi

Pressure tunnels are constructed nurously in related with powerhouse. In some cases, according to high internal water pressure, rock mass around tunnel can seldom suffer this pressure. So installation of concrete lining which interacts with rock mass and suffers parts of this pressure and transfers the rest of the pressure to the rock. In this paper hydromechanical interaction between rock and lining is investigated. With using empirical and numerical methods concrete lining for Symareh waterway is designed. Initial support of 10 cm reinforced shotcret with wire mesh and rock bolts pattern of 2.5*2.5 m with length of 4 m is suggested. By using FLAC package final lining with paying attention to axial force and momentum in reinforced concrete was designed. Reinforced concrete with 60 cm thickness and two rows of bars, 18 mm diameter and 20 cm spacing are designed. Also for preventing cracks in concrete which caused by the change of temperature and shrinkage, bars with 10 mm diameter and 25 cm spacing, and also bars with 8 mm diameter and 10 cm as minimum shear bars are suggested. Plusieurs galeries en pression se construisent en liaison avec les centrales électriques. Dans certaines galeries, suite à une haute pression interne de l'eau, le massif rocheux autour de la galerie ne peut pas supporter cette pression. L'installation d'une couche de béton a l'intérieur de la galerie donc réagit avec les roches et support d'une partie de cette pression et transfère le reste de la pression aux roches. Dans ce papier, l'interaction hydromécanique entre la roche et la couche en béton a été étudiée. En se basant sur les méthodes empiriques et numériques le système de support de galerie de passage d'eau de Saymareh a été conçu. Un soutènement initial d'une épaisseur de 10 cm de béton étant renforcé par un grill métallique et une maille de boulon (2.5 * 2.5 m) d'une longueur de 4 m a été proposé. En utilisant le logiciel de FlAC, la couche finale en béton selon les forces dans le béton a été conçue. Le béton renforcé d'une épaisseur de 60 cm et deux ranges d'armateurs (18 mm de diamètre) avec un intervalle de 20 cm a été conçu. De plus; pour éviter des fissures dans le béton suite au changement de la température et de l'extraction, des armateurs de 10 mm de diamètre et de 25 cm d'intervalle pour augmenter la résistance au sciesiement du béton ont été proposes Unter Druck stehende Tunnels werden hauptsaechlich im Zusammenhang mit Kraftwerken gebaut. In einigen Faellen, wo der Wasserdruck zu hoch ist, Kann selten die Felsenmasse diesen hoehen Druck allein aufnehwen. Deshalb werden sie mit Betonauskleidung versehen, die wegen guter Wechelwirkung mit der Felsenmasse einen Hauptanteil des Druckes aufnehmen Kann, wobei der Rest an die Felsenmesse weitergeleitet wird. In dieser Arbeit wird die hydromechanische Wechelwirkung zwischen der Gesteinmasse und der Auskleidung untersucht. Mit Hilfe empirischen und numerischen Verfahren sowie Kombination der beiden wurde eine Betonauskleidung fuer die Symareh Wasser Kannal koustruiert. Als erstes wurde ein 10Cm dicker armierter Beton mit einem Mashengitter von 2.5*2.5 sowie den gleichen Felsbolzenabstaenden und einer Laenge von 4 m vorgeschlagen. Mit Hilfe des FLAC Programms wurde die Hauptauskleidung unter Beruecksichtigung von Axialkraeften und Momenten im Stahlbeton koustruiert. Der 60 Cm dicke Stahlbeton wurde mit zwei Reihen von Stangen, 8 mm im Durchmesser und in Abstaenden von 20 Cm koustruiert. Ferner im Sinne der Vorbeugung gegen Rissen im Beton, die durch Temperatur aendeungen und Schrumpfungen bedingt sind, wurden Stangen mit 10 mm Durchmesser und 2.5 Cm Abstaenden zur Erhoehung vor Scherfestigkeit des Betons vorgeschlagen.

Jan 1, 2003

By Conné Spangenberg

Contents ?Introduction ?Metal accounting environment ?Problem statement ?Investigations & Achievements ?Metal Accounting ?Principles ?Standards ?Audits ?Questions

Jan 1, 2005

By S. D. Viljoen

The use of ceramics to protect equipment subjected to wear in abrasive and corrosive applications has been accepted by most plants as the industry norm. Little is, however, known about alternative special ceramic based products which are available for the protection of plant assets. With careful engineering, impact resistant ceramics can be used in high impact zones using modern ceramic technology. Properly selected and properly installed, ceramics will provide a tough wear resistant lining for protection against abrasion and impact. Basalt, on the other hand, is widely used in coal washing plant process pipes with varying degrees of success. Basalt is normally not used for the lining of bends, ?T? pieces or reducers due to the reduced wear resistance compared to alumina ceramic. The advantage is a much reduced initial capital cost. A patented ceramic composite non-return valve solved an old problem encountered in the operation of medium sumps. The design approach overcomes the lack of functionality of alternative designs and reduces valve wear while preventing medium settlement during plant shutdown periods. Direct bonded ceramic pulley lagging is becoming the industry norm, eliminating most of the problems encountered with conventional pulley lagging systems.

Jan 1, 2010

By W. Mbhalati

"Conzal Mine was not meeting production targets in 2013, and it was established that this was caused by the inability of the load haul dump machines (LHDs) to tram the required tonnages. An investigation of the LHD productivity was therefore conducted to identify the inhibiting factors. This was accomplished by carrying out a literature review on LHD operations to gain in-depth knowledge and conducting observations in the working environment. The relevant information and data on the LHD type used at Conzal was also acquired.The major inhibitor was found to be excessively long tramming distances in all the sections of the mine. The one-way tramming distances were all significantly greater than the 90 m set in the mine’s code of practice (COP), with the Main Shafts section having the longest average one-way tramming distance of 260 m. The other inhibitor was LHD utilization, which in 2013 was only 47% against a target of 70%. Simulation of the LHD operation, taking these two factors into account, showed that production could be increased by more than 100%. As a result, it was recommended that conveyor belts should be extended regularly in order to keep tramming distances within the recommended one-way distance of 90 m. In addition, utilization can be improved by minimizing employee absenteeism as well as by modifying the travelling routes such that LHDs do not encounter unnecessary delays.Paper written on project work carried out in partial fulfilment of BSc. (Mining Engineering)"

Jan 1, 2015

By A. Kapito

The ferrite-pearlite microstructure is the most popular microstructure for alloys used in structural applications, including railway wagon wheels. These alloys have been designed through alloying and thermo-mechanical processing to have a refined microstructure. Ferrite-pearlite alloys are low cost, weldable, have good fabricability, and are reliable under extreme conditions. Given these performance attributes, it seems unlikely then that their dominant position as structural steels would ever be challenged by alternative microstructures. One major achievement in the development of ferrite-pearlite steels has been in the refinement of their interlamellar spacing to very fine distances of the order of < 0.3 um. A refined microstructure increases the hardness of the alloy, thus increasing its life under wear conditions. The interlamellar spacing in pearlitic steels has, however, been refined almost to its theoretical limit. The increasing demand for speed and increased axle loading on railway wagons requires the use of stronger, tougher, and more durable materials. This has opened the window for the development of novel bainitic steels. Bainitic alloys have a higher level of microstructural refinement than pearlitic ones. They have shown to have good wear resistance and rolling-contact fatigue resistance, and high toughness. This paper will discuss the progress to date on the development of bainitic railway wheel alloys. Four alloy chemistries have been chosen for possible further development.

Jan 1, 2012

By S. A. Aye

Vibration levels on a variety of equipment in a South African opencast mine were measured in this study. The well-established ISO 2631-1 (1997) standard methodology was used for the computation of weighted root mean square (WRMS) and vibration dose value (VDV). This method was used to evaluate the whole-body vibration (WBV) on a wide range of equipment in the opencast mine using the two main parameters, namely the daily exposure A(8) which is based on the WRMS concept and the VDV which measures shocks. The results obtained show that while the majority of the equipment rendered exposure levels that are below the exposure limit value (ELV), exposure levels on about half of the equipment do exceed the exposure action levels. The study also highlights the importance of shock in the observed responses.

Jan 1, 2011

By L. Malmgren, A. Ansell

This paper deals with the influence from blast induced stress waves on the performance of shotcrete support in the Kiirunavaara mine. Time histories of stress waves from blasting were obtained from measurements during production blasts in the mine, followed by failure mapping. A finite element model, consisting of beam and spring elements, was used to calculate the shotcrete response to vibrations from blasting. The modelling approach was similar to that of a building during an earthquake, with accelerations measured in-situ used as loads. The analysis showed that the calculated adhesive stresses exceeded the strength in the interface between rock and shotcrete near to the blasted ring. It also indicated that tensile rock failure did occur. These types of failure will presumably result in ejection of joint defined rock blocks or rock slabs and will require a ductile support, such as fibre reinforced shotcrete. The predicted failure was confirmed by the mapping, which also showed that the zone of failed shotcrete was much larger in areas with plain shotcrete compared to areas with reinforced shotcrete. L’influence de l’onde de pression générée par les sautages à la mine de fer de Kiruna sur la performance du béton projeté est étudiée dans le présent article. Les ondes créées par les sautages ont été enregistrées et les domages résultants ont été cartographiés. La réponse du béton projeté aux vibrations de sautage est étudiée à l’aide d’un modèle d’éléments finis, constitué de poutres et de ressorts. L’approche est similaire à celle d’un immeuble subissant un tremblement de terre, avec les accélérations internes utilisées comme charges. L’analyse montre qu’à proximité des sautages, la contrainte adhésive dépasse la résistance de l’interface roche-béton. L’analyse confirme aussi l’existence de ruptures en tension. Ces types de rupture induisent probablement l’éjection des blocks définis par les structures du massif rocheux et requierent un support ductil, comme du béton projeté renforcé par exemple. Le type de rupture est confirmé par les observations de terrain, qui montrent aussi une extension plus importante des domages lorsque le béton projeté n’est pas renforcé. In diesem Konferenzbeitrag geht es um den Einfluss, der aus einer Sprengung hervorgerufenen Schwingungswellen auf die Ausführung der Spritzbetonverstärkung in dem Kiirunavaara Bergwerk. Die Aufzeichnungen der Schwingungswellen von Sprengungen gemäß einer Fehlerkartierung beziehen sich auf Messungen, die während der Sprengungen durchgeführt wurden. Ein Finite Elemente Modell, bestehend aus Stab- und Federelementen, wurde für die Berechnung der Spritzbetondeformation in Bezug auf die Schwingungen aus Sprengungen angewendet. Die Modellierungsmethode war ähnlich der eines Gebäudes während eines Erdbebens anhand der gemessenen Beschleunigungen vor Ort, die als Lasten benutzt wurden. Die Untersuchung hat gezeigt, dass die berechnete Haftspannung größer war als die Festigkeit in der Verbindung zwischen Gestein und Spritzbeton in der Nähe des Sprengungscentrums. Die Analyse hat gezeigt, dass die Zugfestigkeit des Gesteins versagte. Diese Arten von Versagen werden als Folge der Herausnahme von Gesteinsbrocken oder Gesteinsplatten erklärt und benötigen eine faserverstärkte Spritzbeton. Das vorausgesagte Versagen bestätigte sich beim Kartieren, welches auch zeigte, dass die Zone des versagenden Spritzbetons in Bereichen mit unverstärktem Spritzbeton viel größer war als in Bereichen mit armierten Spritzbeton.

Jan 1, 2003

By M. S. P. Rampedi

The paper reports on a vacation work project conducted at Khuseleka No. 1 Shaft, Anglo Platinum, where there was a need to optimize the transport of personnel to level 15 and below. Approximately 900 men per hour need to travel between the shaft and the start of the current chairlift system. Time studies were used as the major indicator of the extent of the current problem, and it is recommended that a new chairlift system be installed to cover the distance from the vertical shaft station at level 15 to the chairlift decline station on level 15. A capital cost of approximately R10 million is necessary to carry out the proposed recommendation. Khuseleka No. 1 Shaft has the capacity to wind 1070 people per hour, and the current labour complement going to the level 15 shaft station stands at 1570 employees; thus at optimum efficiency the proposed chairlift system could transport the entire shift to the start of the current chairlift system in only 1 hour and 45 minutes. Reducing the distance walked at the start of the shift may also have an impact on productivity.

Jan 1, 2012

The influence of varying amounts of magnesia, silica, and alumina in iron ore sinter on its mineralogy, reducibility index (RI), reduction disintegration index (RDI), physical breakdown (AI and TI), and production properties (coke breeze rate) were examined. It was found that the mineralogy of iron sinter can more easily be predicted from its chemical composition than from the RI, RDI, AI or TI. Anticipating the consequence that varying amounts of MgO and SiO2would have on sinter properties is complex, and not necessarily predictable. High concentrations of Al2O3in the sinter result in high concentrations of the SFCA phase, but with drastically deteriorated properties. This study also confirmed that the form in which fluxes are added to the raw material sinter mixture affects the mineralogy and properties of the produced sinter.

Jan 1, 2010

A reliable laboratory method to characterize the response of free gold particles to flash flotation conditions has been developed. The test has been performed on free milling gold ores as well as synthetic ores, using either a gravity concentrate or gold powder as the gold source, to assess the floatability of gold particles. Trends in free gold flotation kinetics, as well as size and milling effects, were identified for gold recovery based on the different feed types, reagent dosages, and residence times. It was shown that the ultimate recoveries and kinetic trends of gold particles from the gravity concentrate could be enhanced with increased dosage of collector, potassium amyl xanthate. Interestingly, in comparison to gravity-recoverable gold, recovery from pure Au powders was better in collectorless flotation, and cumulative recovery decreased with higher levels of collector addition. Improved coarse particle recovery appeared linked to increased collector additions for both the gravity concentrate and the pure gold powders. In general, coarse gold particles demonstrated slower kinetic rates thaen the fine or intermediate components incomparable tests.

Jan 1, 2015

By R. Hope, C. van Heerden

In any process or organization inefficiencies are costly. In times of abundance this reality often does not receive much attention. During such times the focus is rather on increasing capacity to increase production. However, there is a growing awareness in the world of tougher economic, social as well as environmental conditions, and enterprises find themselves facing greater demands for accountability towards shareholders, the environment and the public, as well as growing competition for market share and limited global resources. This reality is no different in ensuring a sustainable mineral sands operation. In order to achieve this, any operation needs to be stripped of all process as well as operational inefficiencies. In this context it has become essential for any Mineral Separation Plant (MSP) to have the necessary process monitoring and control systems in place to continually monitor and optimize the production of on-spec products and maximize operational efficiency and consistency. The MSP Grade Control Solution developed by Crusader Systems and running on top of the CSense platform contributes towards these goals by improving the consistent production of on-grade product. This allows the process to operate closer to the maximum allowable product grade constraint, which in turn maximizes production.

Jan 1, 2003

By A. Fahimifar, H. Soroush

Abstract: In order to develop non-destructive methods in studying physical and mechanical properties of rock and replacing them with difficult and expensive static methods, several ultrasonic tests were carried out on cylindrical rock specimens in accordance with the ISRM suggested methods and velocity of P and S waves were determined. Also, density, porosity, water absorption, uniaxial compressive strength and indirect tensile strength were determined for each specimen in accordance with ISRM suggested methods. According to above tests static and dynamic elastic constants were calculated After statistical analysis of data obtained from tests, the relationships between velocity of elastic waves and physical or mechanical parameters were determined and some equations were obtained. Also similar analyses were performed on static and dynamic constants and some equations were extracted. Using these equations, the physical and mechanical parameters of rock and also static elastic constants can be estimated by conducting simple and quick tests (i.e. ultrasonic tests). Abriß: Um zu entwickeln, die zerstörungsfreien Methoden für Studieren die physischen und mechanischen Eigentümer von Steinen und auch ist für Ersetzen diese Methoden mit schwierigen teuren statischen Methoden, mehrere altrasonic Prüfungen auf zylindrischen Steinproben gemäß ISRM anregenden Methoden und den Geschwindigkeiten von S und P Wellen bestimmt worden sind durchgeführt worden. Außer der Dichtheit und der Porosität betonen Wasser Aufnahme und monoaxial Widerstand und dehnbaren indirekten Widerstand jeder Probe betreffend der erhaltenen Ergebnisse die atmosphärische Aufladung sind bestimmt worden und die dynamischen Faktoren der Steine sind kalkuliert worden. Nachdem statistische Analyse die Korrelation der Ergebnisse zwischen der Geschwindigkeit elastischer Wellen und mechanischer und physischer Eigentümer der Steine erhalten worden ist, und mehrere Verhältnisse sind vorgeschlagen worden. Eine ähnliche Analyse ist auf atmosphärischer Aufladung und dynamischen Faktoren durchgeführt worden und einige Verhältnisse sind erhalten worden. Mit Hilfe dieser Verhältnisse die physischen und mathematischen Eigentümer von Steinen und auch können die Statistik Faktoren durch einfachen und schnellen altrasonic Prüfungen erhalten werden. Resume: Puor le development des method non-destructive et evaluuation des propietes physical et mechanical des rock et superseding avec les methods dificzle et cher statique, c‘ est fait plusieur essayes ultrasonique sur les echantillons cylinrique et par a port le proposale TSRM et le vittesse des ondes P et S et densite et porosite et absorption des eaux le resistant de pression uniaxial et resistance de chaque echantillon est determinee. A la fin en base des resultat obtenue les constant statique et dynamique des roches sont calcule. Apres les analyses statistiquc sur les resultat obtenue du les essaybs, c‘ etait produit les relation entre les viptesse les ondes elastique et les proprietes physic et mechanicue des roches et c est propose quelque relations. Aussi le meme enterpretation sur les constant statique etdinamique. En possezon de ces relations, les spesificatio physique, aussi on peut trouver leur constant statique, avel les essayes sample et raptid a d ultrasonique.

Jan 1, 2003

By D. P. Roberts

The stoping of platinum orebodies in the Bushveld has in the past been accomplished by using in-stope pillars to ensure stability of the workings. In the future, the use of continuous mining machines to mine the platinum orebodies is probable. It is not envisaged that such machines will cut in-stope pillars. This paper describes the alternative support systems that will replace the pillars and the stope geometries that will be required for this type of mining. The paper describes how the support resistance provided by in-stope pillars in current mining was determined and then evaluates support systems that can substitute for these pillars. Conceptual layouts based on existing breast mining layouts are presented. The layouts consist of panels of up to 100 m face length between rigid strike stabilizing pillars. A number of design charts are then proposed that allow for the design of appropriate support systems.

Jan 1, 2005

By Y. M. Zhao

The separating performance of a pilot dry beneficiation system using a gas-solid fluidized bed was investigated with coal from South Africa. The coal used for the study has a low inherent moisture content, a moderate ash content, a moderate volatile content, a low sulphur content and a high calorific value. Its washability is moderate. Experimental results show that the separating quality of the fluidized bed drops gradually as the feed-coal particle size decreases. The probable error, E, values for 50?25mm, 25?13 mm and 13?6 mm coals were 0.04 g/cm3, 0.06 g/cm3 and 0.09 g/cm3, respectively. The cause of the differences in separating characteristics was analysed by particle dynamics and numerical modelling. Furthermore, the pilot fluidized bed was employed to separate 50-6mm coal. In this experiment the coal ash content was reduced from 23.74% to 11.79%, with a probable error, E, value of 0.07 g/cm3and a recovery efficiency of 98.26%. This indicates that the fluidized bed is applicable to the separation of coal from South Africa and has good separating performance and wide applicability. Keywords: feed-coal particle size; gas-solid fluidized bed; dry coal beneficiation; numerical simulation.

Jan 1, 2010

By S. Asokan, CVGK Murty, R. Upadhyay

The principal mineral sources of titanium are rutile, anatase (both TiO2), ilmenite (FeTiO3) and leucoxene (a weathered ilmenite of variable concentration of TiO2 but similar to pseudorutile Fe2Ti3O9). These titaniferous minerals along with their value added products like Synthetic Rutile and TiO2 slag constitute ?Titanium Feed-stocks? for TiO2 pigment, Ti metal and welding electrodes industries. Unlike in other industries, the demand driver for titanium minerals is not the metal, but the TiO2 pigment ?a specialty chemical. Of the total titanium feedstocks usage in the world, about 93 % is consumed in TiO2pigment, with only about 3 % is utilized in metal production. India?s heavy mineral sands resources are among the largest and also one of the richest grades in the world. The country?s Ilmenite resource base stands at 348 million tonnes of Ilmenite (18% of the total world reserves)along with 18 million tonnes of Rutile, 21 million tonnes of Zircon, 8 million tonnes of Monazite, 107 million tonnes of Garnet and 107 million tonnes of Sillimanite. Though the grades (Total Heavy Minerals (THM) present in the sand) of Indian deposits are relatively rich, the contained ilmenite are termed as sulphate grade with 50-53% TiO2 (Chavra deposit of Kerala and Ratangiri deposit of Maharastra are an exception with 60% of TiO2). While superior grades with adequate reserves lead to a cost advantage in ilmenite production, the lower TiO2 percentage allows the direct use of Indian ilmenite only in the production of TiO2 pigment through sulphate route and for the chloride pigment production; such ilmenite is required to be upgraded either to Synthetic Rutile (SR) or TiO2 slag. However, in order to produce TiO2 slag in India at a globally competitive cost, the issues like high power tariff, inadequate infrastructure, expensive logistics, less enthusiastic market preferences, supply-demand gaps are to be adequately addressed. This paper deals with some of the above issues and possible solutions thereto in production of TiO2 slag from Indian ilmenite.

Jan 1, 2007