Search Documents

By J. T. Liu

Packing in a flotation column is one way to increase separation efficiency and effective descending flotation-column height. In this paper, the difference between filling packing and sieve packing is described, and the flaws of filling packing in flotation columns in industrial application are pointed out. A change of flotation process and its effect on flotation results are reported. Based on sieve-plate filling, a high-efficiency mixed packing mode consisting of screen-plate packing and honeycomb-tube packing has been proposed, with the packing mode optimized in the cyclonic static microbubble flotation column in the separation zone. In the mixed packing mode, the honeycomb tubes are used to reduce the vortex effect at the base of the column and weaken the radial dispersion of jetting bubbles, and the sieve plates are used to comminute bubbles in the separation zone, to lengthen the bubble migration path, and to stabilize the foam layer. The superiority of honeycomb-tube packing is analyzed using bubble-particle collision theory, and the dynamic equations of collision probability are derived. The role of mixed packing in guaranteeing mineral recovery is analyzed by the axial dispersion method, and a dimensionless axial dispersion model is derived. When a high-turbulence flow is maintained, a static separation environment is formed in which secondary mineral processing is rendered more effective. In this way, a nonlinear separation environment is formed in the flotation column. Finally, mixed packing was applied in an industrial test. A large vortex developed at the base of the column. It was observed that the bubbles in the radial flow were homogeneously dispersed, the residence time of the pulp was prolonged, and the froth layer became thick and stable. Based on the test data, it was found that the sieve packing has the potential to yield a product of approximately 25.83% copper concentration with 91.78% recovery from a feed concentration of approximately 0.727%. If mixed packing were used, the product concentration could be further increased to 27.60% from a feed of approximately 0.739% concentration with 93.38% recovery.

Jan 1, 2014

By E. T. Tuzcu

In this manuscript, a new approach for modeling the rate of grinding process is explained. A review about grinding rate definitions so far is given and the possible ultimate way for grinding modeling is given as modeling the rate based on energy spectra. The traditional/phenomenological approaches for modeling size distribution of grinding mills give their place to a new generation modeling technique. Developments in the computational methods and necessity to model product size distribution of large mills, larger than ball mill size, paved the way for this novel technique. The traditional grinding rate models are mostly based on the back calculated breakage parameters from the experimental data. However, direct modeling of breakage parameters and hence the prediction of size distribution of the grinding mills may become possible with this approach. The material breakage data and discrete element method (DEM) energy spectra are the main components of this approach. Albeit the focus in this study is on modeling of breakage rate under impact mode of breakage, the abrasion mode of breakage was also tested by carrying out abrasion tests. Impact mode of breakage was analyzed using ultra-fast load cell device (UFLC) and drop weight tester. Dry tumbling test was carried out for abrasion experiments. Obtained material breakage versus energy data are combined with the collision energy spectra to obtain the breakage rate function. In addition, the material breakage versus energy information from the tests is converted into breakage distribution function. The model was verified in a lab scale mill (90 cm diameter-15 cm length). 10 to 15 kg of limestone was ground using 50 mm steel ball at varying conditions, i.e., rpm, volume loading. It is shown that the proposed model predicts all (1, 2, 4 min.) grinding intervals for all experiments highly accurate.

Sep 1, 2012

By A. T. Adema

The cohesive zone, where the ore fed into the blast furnace softens and melts, is critical to the blast furnace performance and stability due to its influence on the gas and solid flow. This paper de-scribes a project for the development of a process model to predict the cohesive zone properties and the results of its first step; the solid flow model. The process model is expected to describe a realistic solid burden flow and the formation of the cohesive zone, its shape, location, structure, permeability, and in particular the mineralogical changes within the cohesive zone. This will be achieved using various simulation and computing tools: a combination of the Discrete Element Method (DEM) and Computational Fluid Dynamics (CFD), the DEM?CFD hybrid approach, together with models for the thermodynamics and reaction kinetics. The key benefits of the hybrid approach lie in the coupling of the continuous phase and the discrete particles, and the possibility of introducing thermodynamics and reaction kinetics into the system in a more realistic manner. Two DEM simulations are presented for a small scale blast furnace to investigate the influence of non-spherical particles on the solid flow. This influence can be observed from a more even solid flow pattern and a reduced deadman size. The results indicate the requirement to include non- spherical particles in a blast furnace simulation to achieve a realistic solid flow.

Jan 1, 2014

By M. X. Jia

This paper discusses two mineralogy characteristics that may affect the flotation of sulfide ore. The first one, process mineralogy study on a Cu-Ni sulfide ore shows that valleriite and tochilinite are incline to form on chalcopyrite, pyrrhotite and serpentine surface, and the further guess is that the formation of valleriite and tochilinite may also causes the serpentine transform to talc, so the serpentine surface is a phase of talc or a transition phase from serpentine to talc and this enhances the flotability of the gangue minerals. The second discussion on the flotation behavior of the sulfide minerals from the point of view of the mineral semiconductor character.

Jan 1, 2014

By Z. S. Abisheva

Rare and rare earth metals use quite often is an indicator of national economy development. The world structure of the rare-earth metals manufacturing countries in 2015 was presented as follows: China – 94.2%, India – 2.0%, Russia – 1.8%, the USA – 1.2%, Brazil – 0.5%, Malaysia – 0.3%. In Russia, large reserves of rare-earth metals, which reach nearly 28 million tons, are revealed. Kazakhstan, possessing a raw materials source of rare-earth metals, has all prerequisites for development of branch. Rare metals are manufactured in Kazakhstan incidentally by non-ferrous metals production. The production of indium, thallium, cadmium, selenium, tellurium, bismuth is made at the Ust-Kamenogorsk lead plant; tantalum, beryllium, niobium and molybdenum – at the enterprises of “National Atomic Company Kazatomprom” JSC. Production of a titanium, magnesium and vanadium is adjusted on “Ust-Kamenogorsk Titanium-magnesium Plant” JSC. Capacities for beryllic production yield are available on “Ulba Metallurgical Plant” JSC. The main producer of perrhenic production and osmium-187 is "Zhezkazganredmet" RSE. The single producer of gallium in Kazakhstan is “Aluminium of Kazakhstan” JSC; the capacity of enterprise is 25 t a year. In Kazakhstan innovative technologies for rare and rare earths mineral raw materials processing are created. The technology has been developed and a vacuum distillation apparatus has been created to purify crude selenium, which makes it possible to obtain a metal with a main component content of 99.9-99.99%. Technologies for processing of technogenic wastes and byproducts of the copper industry are developed. Implementation of technologies allow to obtain ammonium perrhenate, perrhenic acid, osmium isotope -187, tribasic lead sulphate, silver-concentrate. The technology of complex processing of black shales of Balasauskandyk deposit with the production of gold, vanadium, rare earth elements, uranium and ferrosilicon has been proposed. The processing was carried out using methods of autoclave leaching, sorption, extraction, precipitation. A highly profitable sorption technology for recovery of rhenium from solutions of underground leaching of uranium ores containing 0.2-0.4 mg/L of Re has been created. The organization of ammonium perrhenate production from solutions of uranium ore will significantly increase the volume of its production in Kazakhstan.

Jan 1, 2018

By G. Alfano

This investigation is concerned with the optimization of ultrafine grinding of solids. It is focused on a dynamic classifier for recovering the fine fraction, for automatic recycling of the oversize particles and for reducing power consumption. Power consumption plays a major role in these energy intensive processes and depends on several parameters such as nature of the solid, degree of fineness of the finished product and, above all, grain size of the feed. This study indicates the optimal conditions for a dynamic classifier, that is, geometric characteristics of the apparatus and its capacity, inlet air flow rate and dimensions of the classification circuit. It is also shown that a mean grain diameter (dm) of about 2.00 µm with top size (dmax) of 50 µm can be achieved with an imperfection value of below 0.40 and energy consumption of 215 kWht-1. Keywords: air classification, dynamic classifier, jet mill, energy

Sep 1, 2012

By M. Prasad

Growing concern over increased levels of atmospheric carbon dioxide has prompted new interests in development of materials and techniques for its sequestration. Various research and developmental work on different aspects of carbon capture technology are being extensively carried out worldwide. The main objective of the present work is to synthesize a HAS material having high capacity and robust ability for recycling to capture greenhouse gases with special reference to carbon dioxide (CO2) from the sources from where it is released to the atmosphere. Existing CO2 capture techniques involves the use of solid materials that lack sufficient stability for repeated use or liquid adsorbents that are expensive and require significant amounts of energy. Keywords: greenhouse gases, carbon capture, solid adsorbent, HAS material

Sep 1, 2012

By H. R. Manouchehri

The importance of the grinding environment and its effect on sulphide minerals flotation behavior has been known for many years. The grinding environment may play a role in controlling fine and coarse particle flotation along with dissociation of different chemical species in grinding environment. Dissociation of different chemical species and ions within the process water may result from changing the grinding environment. The mining and mineral processing industry undertakes activities that may impact on water resources. These include use and storage of chemical storm-water management, process water management, mine dewatering and management of tailings. In mineral flotation understanding and controlling water quality is paramount important not only because of its effect on flotation but also with respect to control the quality of the water which is released to the environment. Releasing of different anionic and/or cationic chemical species in the process water results from the interactions among different mineral within the ore, process water, and the milling environment. In fact grinding mill acts as an electrochemical reactor which affects the flotation performances of different value minerals as well as the quality of the tailing products. An increasing in antimony content in process/discharge water at Boliden?s Tara processing plant in Ireland to above limitation level was reported in April 2010 which needed to be controlled. An increase up to 6 times of the permitted level was reported which needed an immediate action to control due to environmental considerations. Therefore attempts were made to detect why this higher amount of Sb is released and how to control and minimize its release to the process/reclaim water. This paper discusses how/why Sb content in process/reclaim water was increased by changing the mill electrochemistry and the strategies were taken into considerations to control it. Different strategies, including electrochemical controlling of the milling section, Fenton process, using Bauxsol in treating the process water, etc., have been considered and tested which are described herein. All strategies taken into consideration for solving the problem were successful which indicated good understanding of the issue and good decision making. Furthermore, for each solution the capital and operational costs were roughly estimated. Accordingly, the Sb content in process/discharge water was controlled to a value lower than allowed limitation, i.e., 1 ppm. Keywords: antimony, water contamination, mill electrochemistry, ag milling, grinding media, eh-ph, sulfide minerals, fenton process, bauxsol, lime addition

Sep 1, 2012

By V. I. Ryaboy, V. P. Kretov, S. E. Levkovets, I. V. Ryaboy

"Using the flotation of a gold-containing ore from a deposit in Kazakhstan as an example, we have conducted a study designing dialkyldithiophosphate collectors, in addition to xanthates, for the flotation of hard-toenrich gold-containing ores to increase gold recovery.The increased flotational ability of the dialkyldithiophosphates was determined by their surface activity at the liquid-gas interface and their hydrophobic ability, the changing of which allowed us to control the collecting power and selective ability of the dialkyldithiophosphates. The studying of the surface activity of aqueous solutions was done using the stalagmometric method and the evaluation of the hydrophobic ability was done in percentage of the relative value of the zinc ion binding in the solution in standard conditions.Studying the influence of surface activity in our designed dialkyldithiophosphate collectors, with their close hydrophobic ability, showed that even with a small increase in surface activity in their aqueous solutions, gold recovery increased by 2-3% in laboratory conditions. Using this enabled us first to apply the dialkyldithiophosphate collector BTF-161 at a plant in Kazakhstan, and then to introduce the specially designed dialkyldithiophosphate collector BTF-163, which has been in use since. Further study of dialkyldithiophosphate activity based on this concept showed us that for the range of short-chain dialkyldithiophosphate collectors with a chain length of up to ?5, the effectiveness of ore processing became lower the higher their surface activity got, with relatively small differences in their hydrophobic ability. For long-chain dialkyldithiophosphates with a chain length of over ?5, ore processing effectiveness increased with the increase of their hydrophobic ability.Based on these studies, a new effective dialkyldithiophosphate collector, BTF-1517, was designed. Using this reagent in continuous gold recovery tests allowed us to reach an 84.21% recovery with a concentrate quality of 15.66 g/t, while using the applied collector BTF-163 in similar conditions led to the recovery of 82.87% with a concentrate quality of 15.65%. As a result, the Kazakhstan processing plant decided to conduct industrial tests with the BTF-1517 collector."

Jan 1, 2018

By T. V. Vijaya Kumar

Most of the iron ore washing plants set up in India consist of sizing of the ore by dry / wet screening, washing and classification by screw classifiers followed by multi-stage hydrocycloning of screw classifiers? overflow. The underflow of the hydrocyclones forms the concentrate which is used for pellets making. As the cut-point of hydrocyclones is generally at 20 microns, relatively lower diameter cyclones in a cluster with parallel feeding are used. This is found to, often, result in choking of the spigots, at times, by extraneous material as well reporting along with the slurry. It is observed to lead to sub-optimum performance of the cyclones with loss of iron values into cyclone overflow and thereafter into tailings. Analysis of data of an operating beneficiation plant (Beneficiation Plant - 1, BP - 1) of M/s Jindal South West (JSW) Steel Limited, Karnataka, India over a period of one year indicated that weight recovery of the concentrate from two-stage hydrocycloning was 45% (with respect to feed to the cyclones) and assaying 63.43% Fe, 4.43% SiO2 and 2.32% Al2O3. CSIR - National Metallurgical Laboratory - Madras Centre (NML - MC), India developed flotation process for processing screw classifier overflow with a view to improve the recovery of ultrafine iron values from it. Detailed investigations at laboratory scale flotation column and on-site pilot plant trials proved that the production of the concentrate and productivity of the plant could be enhanced by adopting reverse cationic column flotation technology. It was established that a typical screw classifier overflow analyzing 60.54% Fe, 5.95% SiO2 and 3.67% Al2O3 could be upgraded to 64.21% Fe, 2.64% SiO2 and 2.20% Al2O3 with 82.7% weight and 84.7% Fe recovery. This translates into an increase of 80% in weight recovery of the concentrate compared to what is being obtained, at present, by two-stage cycloning. It had an added advantage of reduced SiO2 in the concentrate. Thus, SiO2 in the final concentrate could be reduced to 2.64% from 4.43% by adopting column flotation. The concentrate so generated meets the stringent specifications, especially in terms of alumina in it(should be less than 2.50%) for pellets making. Later, JSW Steel Limited set up the flotation plant in BP - 1 based on the process developed by NML - MC and was commissioned in 2010. Keywords: iron ore, washing, ultra fines, alumina reduction, column flotation

Sep 1, 2012

By G. Prabhulingaiah, D. M. R. Sekhar

"A phosphate deposit of estimated 6 billion tons of P2O5 is located 180 to 300 meters below the sea level, 185 kilometers north of port Luderitz, Namibia. The ore bed is 6 kilometers wide and 220 kilometers long. The ore deposit analyzing 16% P2O5 is loose sediment of 1.5 meters thick without over burden. Sizing of the ore to - 1.4 mm + 0.150 mm improves the grade to 23.54% P2O5 with a P2O5 recovery at 83.75% containing phosphate pellets and flakes of sea shells. Clay, bacterial debris as organic matter, flakes of broken sea shells and fine phosphate containing particles report to - 0.150 mm fraction and + 1.4 mm fraction contains sea shells and few phosphate containing pellets. The mineralogical composition of phosphate containing pellets is estimated (Droste, T.C., 2004) 80% frankolite, 6% pyrite, 4% illite, 3% quartz, 3% amorphous SiO2, 1% carbonates, 1% organic carbon and = 1% ilmenite, magnetite, zircon etc. The phosphate content in the pellets is around 27.7% P2O5. Trials to separate by gravity or flotation processes were not successful. Leaching of carbonates (sea shell flakes) under mild acidic condition (= 2% acetic acid or HCl solutions) or calcinations followed by leaching however yielded residues (concentrates) of grades 27.85 - 32.74% P2O5 at P2O5 recoveries ranging from 78.45 - 96.8% P2O5."

Jan 1, 2014

By A. A. Sirkeci

In the scope of this investigation comparison between impact breakage and compression breakage were carried out for the separation efficiency of minerals using a chromite ore sample. The ore sample was broken below 1 mm employing a laboratory type roll crusher and an impact crusher. Concentration tests were conducted on -1+0.5 mm, -0.5+0.2 mm and -0.2 mm size fractions using a Wilfley type shaking table. Test results showed a remarkable difference between two types of breakage. Both concentrate grade and recovery was in the favour of impact crushing. Furthermore, the shape of the broken particles also showed differences such that in the case of impact breakage they were more spherical compared to compressive crushing. The results of the shaking table con-centration tests showed that a concentrate assaying 48.4% Cr2O3 were obtained with 78.5% recovery in the case of impact breakage. On the other hand the concentrate grade and recovery values were 48.8% Cr2O3and 52.4% respectively in the case of compression crushing. The losses in the tailings were also in favour of impact breakage proving that differential breakage occurred between chromite and gangue minerals.

Jan 1, 2014

By O. Jerez, A. Novoselov, L. Gutiérrez, J. Morales, U. Kelm

"In Chile, the evaluation to reprocess tailings for elements other than the traditional Cu, Mo, Au, and Ag, as well as projects to implement long-term monitoring of mining residue sites are key elements of the government’s roadmap laid out for the mining industry for the next two decades. Characterization routines for tailings and mining residues in general have to be adapted from traditional ore and gangue mineral and micro-chemical studies. This contribution summarizes key aspects for the regional mining industry for a basic characterization of tailings with emphasis on small- to medium-size operations with limited in-house facilities and funds to carry out extensive characterization programs. The oldest tailings in Chile were deposited almost a century ago; this fact gives importance to the recovery of past ore /gangue feed information, process circuits and changes (e.g. acid to alkaline flotation), process water provenance and recovery, meteorological registers, and routines of filling a tailings impoundment. Basic characterization should include X-ray fluorescence spectrometry combined with laser diffraction (LD) granulometry followed by X-ray diffraction (XRD), optical microscopy (OM) and automated mineral analysis (AMA) on a reduced set of samples identified by hierarchical cluster analysis. For this detailed stage, only coarse tailings are recommended for direct a study by microscopy and automated mineralogy (P80 >100 µm); for fine tailings (P80 ~30 µm) a combination of XRD and deposit type adapted sequential extraction are more informative options. In particular, for XRD of clay phases, losses of crystallinity may result in deviation of spectra from standard reference phases due to prolonged storage. To monitor surface alteration, scanning electron microscopy can be complemented by Raman spectroscopy to detect residual reagents on mineral surfaces. For reactivity modeling BET measurements are essential."

Jan 1, 2018

By Lala Zhao, Yuemin Zhao, Guangyuan Xie, Chusheng Liu, Chenlong Duan

"Screening is an important means of size classification used on granular or particulate materials. The vibrating modes of screen separator have a great effect on the screening process. Elliptical vibration mode is a complex motion mode which gets the common characteristics of both linear and circular vibration modes. However, the fundamental motion and screen penetration of the particles on the elliptically vibrating screen deck are still poorly understood. A numerical study of the motion of particulates flow along an elliptically vibrating screen deck is presented by means of a three dimensional Discrete Element Method (3D-DEM). The motion characteristic of the particle flow is analyzed at a particle scale. The effects of vibration amplitude, throwing index, vibration direction angle and screen deck inclination angle on the screening process are discussed. The results show that the particles average velocity increases linearly with the increase of vibration amplitude, throwing index and screen deck inclination angle, but decreases linearly with the increase of vibration direction angle. The screening efficiency is highest when the vibration amplitude, throwing index, vibration direction angle and screen deck inclination angle are 4.5 mm, 3.3, 40° and 6°, respectively. This work is helpful for developing a deep understanding of particle motion on the elliptically vibrating screen and for optimizing screen separator designs."

Jan 1, 2014

By J. Wiese, K. Corin, Z. Song

"Relating flotation performance to the electrochemical characteristics of a pulp is complex both in fundamental research and in practice. In the case of thiol collectors, different Eh values in the flotation system can result in the formation of the dimer or the metal thiolate which may or may not enhance the hydrophobicity of the mineral. Reducing or oxidizing conditions in a flotation system, viz. changing the Eh value, are usually manipulated to achieve an optimum flotation response by control of pH and dissolved oxygen levels in the system. A variation in pulp potential may also be achieved by the addition of potential modifiers such as sodium hydrosulphide (NaHS), sodium hypochlorite (NaClO) or hydrogen peroxide (H2O2). There exists anecdotal evidence which suggests that the addition of small amounts of H2O2 to the flotation process can improve sulphide mineral recovery. The objective of the present study was to investigate the effect of the addition of the potential modifier, H2O2, on sulphide mineral recoveries and grades in the flotation of sulphide minerals from two copper bearing ores from China and compare the results to those obtained for a PGM bearing ore South Africa. Batch flotation tests were conducted using the three different ores at the natural pH of the different systems, in the presence of a xanthate collector and the absence and presence of H2O2 as a potential modifier. The results indicate that the addition of carefully controlled low concentrations of H2O2 resulted in improvements in flotation performance. INTRODUCTIONElectrochemical potential as a control parameter in the flotation of sulphide minerals has been widely studied (Allison et al., 1972; Gardner and Woods, 1979; Ross and Van Deventer, 1985; Chander, 2003; Woods, 2003; Javadi, 2013). There is concensus that in order to be recovered during flotation, sulphide minerals require a suitable redox environment. During the flotation process thiol collectors and sulphide minerals are involved in electrochemical reactions which result in the formation of hydrophobic species at the mineral surface (Finkelstein and Goold, 1972; Rand and Woods, 1984). Sulphide minerals act as semiconductors and electrons are transferred during the interaction of the mineral with collector. The resultant potential difference and its magnitude are responsible for the transfer of electrons and the rate of the reaction (Bard and Faulkner, 2001; Fuerstenau et al., 2007). Reducing or oxidizing conditions in a flotation system, viz. changing the Eh value, may be manipulated to achieve an optimum flotation response by control of pH and dissolved oxygen levels in the system (Heyes and Trahar, 1979). The use of potential modifiers viz. reducing or oxidizing agents which include H2O2, NaClO, and NaHS, is an alternative method by which to control the potential of the pulp in a flotation system which may or may not promote the flotation of desired minerals (Rao, 2004). The oxidizing agent, H2O2, undergoes a cathodic reaction which can result in the enhanced flotation of valuable minerals. The potential of the system is increased which results in a shift in the mixed potential of a mineral. The magnitude of the over-potential influences the rate of the oxidation process and thus the flotation response of sulphide minerals (Kocabag and Guler, 2008). Equation 1 shows the proposed oxidation of xanthate by H2O2 (Lipkina and Streltysn, 1970)."

Jan 1, 2018

By P. Somasundaran, G. Anastassakis, Z. Pan, D. R. Nagaraj

Gums are often used as depressants for talceous gangue minerals in the flotation of nickel and platinum bearing ores. However, the mechanisms of gum adsorption on talc are not clearly established. In this work, adsorption of guar gum at the talc-solution interface is investigated using spectroscopic and allied techniques. Guar gum adsorption on talc is not affected significantly by changes in solution conditions such as pH and ionic strength. Electrokinetic studies showed that guar gum decreased the negative zeta potential of talc but did not reverse the charge. Fluorescence spectroscopy studies conducted to investigate the role of hydrophobic bonding using pyrene and dansyl probes showed no evidence of the formation of hydrophobic domains at talc-aqueous interface. Urea, a hydrogen bond breaker, reduced the adsorption of guar on talc to the same extent as that for guar/alumina system, in which hydrogen bond plays an important role. All of the above results suggest that one of the main driving forces for guar adsorption on talc is hydrogen bonding rather than electrostatic or hydrophobic force.

Jan 1, 2003

By Arkady Senchenko, Yevgeny Zhagun, Yury Kulikov, John Starkey

"The paper contains description of a new project in Russia - gold-processing plant at Aleksandrovskoye deposit (start up in September, 2013). The paper includes a brief description of plant flowsheet, data for material composition and technological properties of ore, as well as information about the achieved parameters of ore processing over the first months of plant operation. The project is interesting because a new semiautogenous mill and a ball mill were purchased on the basis of SAGDesign Consulting Group recommendations after the testing of ore samples characterizing the deposit according to specific years of operation. The plant has relatively small design capacity - 750 000 tpa, but nevertheless is the biggest gold-processing plant in the territory of Zabaikalsky region. Major valuable component in the ore is gold, silver is recovered as a by-product. The ores are very hard to grind. The design grinding flowsheet includes a semiautogenous mill operating in closed circuit with a screen, and a ball mill operating in a closed circuit with hydrocyclones (SAB). Process technology includes gravity processing and flotation with subsequent cyanide leaching of concentrates. Mill operation analysis and conclusions about the compliance of the achieved values to target ones are shown, as well as the accuracy of SAGDesign method when applied to very hard ores of Aleksandrovkoye deposit are presented in this paper. Basic directions of technological flowsheet optimization are also given."

Jan 1, 2014

By V. V. Morozov, Ganbaatar Zorigt, Delgerbat Lodoy, Y. P. Morozov

"At the processing plant Erdenet, a new facility for advanced ore diagnostics in-stream (at the conveyor), based on optical analyser of mineral composition, was tested. Such systems provide highly accurate in-stream measurements of ore properties. The system provided information on the ore mineralogical composition, the particle size distribution and the impregnation of minerals. A special flatbed facility for optical spectrum-based estimation of fine-crushed ore has been developed, being incorporated into the existing system of ore sampling and analysis. Application of the flatbed facility renders possible a high accuracy of determining ore mineralogical composition. High precision of the optical spectrum-based estimation is achieved using special devices, installed in the sampling and the sample analysis flow sheet, applied by the technical control department. Modern systems for optical spectrum-based estimation of ore grade provide a basis for effective automated control of ore benefication processes, based on the principle of advanced ore grade control. Process management task of grinding and flotation was to choose options that take into account the composition and grade of the ore coming. The calculation data array comprises consumption of reagents, ore processing, grind size etc. The systems implemented at the processing plant contributed to increasing copper and molybdenum recovery. INTRODUCTION In-stream ore grade analysis is a new trend in effective control of ore benefication processes. This is realised based on radiometric measurements in the X-ray and visible spectrum regions, in which mineral components of the initial ore (Sbárbaro and Villar, 2010) or the benefication products become apparent (Hyotyniemi and Ylinen, 1998; Haavisto and Hyötyniemi, 2010). An important advantage of such methods is in-stream measuring ore parameters, including mass fractions of individual minerals, which makes it possible to use the information obtained in the processes of automated control."

Jan 1, 2018

In many base metal sulphide concentrators reagents such as collector and cyanide are often added to the grinding mill as well as to the flotation circuit. Whilst good reasons can be cited for splitting the reagent addition in this way, the benefits of such are rarely quantified and the complex reagent-mineral-media interactions occurring during milling are often poorly understood in terms of pulp chemistry. A new laboratory batch grinding mill designed by Magotteaux allows the user to measure, monitor, and control the pulp chemical conditions during grinding when testing different ores and media. Some of these parameters include pulp pH, pulp Eh, temperature, gaseous atmosphere, and dissolved oxygen concentration. In a recent development, the mill has been coupled with a simple on-line reagent monitoring system, designed by CSIRO, which allows the levels of species such as xanthate and cyanide in the grinding pulp to also be measured continuously during milling using a robust UV detection system. In this way the uptake of collector during grinding and the rate and ex-tent of cyanide interaction with the minerals and media can be determined as a function of grinding time. A series of grinding tests using an Australian nickel sulphide ore was conducted with the coupled system in which the cyanide dose, xanthate dose, and media type were systematically varied. The xanthate and cyanide levels were monitored as a function of grinding time and the data collected are discussed in terms of the pulp chemistry of the system and implications for plant reagent dosing strategies.

Jan 1, 2014

By Z. Y. Lan

Bioleaching of marmatite with various mixed cultures of microorganisms was investigated. The experiments were carried out in shaking flasks with iron-free nutrient and the pulp density of 10% wt/vol at the temperature of 30?. The results show that zinc is preferentially leached before iron. The leaching rate of zinc with the mixed culture of Acidithiobacillus ferrooxidans, Acidithiobacillus thiooxidans and Leptospirillum ferrooxidans is 62% in 18 days. The leaching rate of zinc with the mixed culture of Acidithiobacillus ferrooxidans and Acidithiobacillus thiooxidans is nearly the same as that with the mixed culture of Acidithiobacillus ferrooxidans and Leptospirillum ferrooxidans (45% versus 50%). SEM and EDX analysis of the leaching residues indicate that a solid product layer composed of iron sulfide, elemental sulfur and jarosite accumulates in the mineral surface and becomes a barrier to the dissolution of marmatite. The bioleaching of marmatite follows the shrinking core product layer model. When the product layer increases and becomes insoluble, the leaching rate is controlled by the diffusion through the product layer and slows down. When the product layer decreases or becomes a porous layer, the leaching rate is controlled by chemical reaction and enhanced dramatically.

Jan 1, 2014