Search Documents

By John Nunes, Frank R. Larson

Temperature-dependent functions of various ten-sile flour stress and fracture parameters were investigated on iron and low composition alloys of Fe-C, Fe-Cr, Fe-Mn, and Fe-Ni. Data were obtained over a range of test temperatures from 200" to -196"C at an initial strain rate of 0.01 min". It was found that the strain-hardening exponent, n, for the Fe-Ni alloys increased significantly at very low testing temperatures with increased alloy addition. Also, the stress and strain at fracture followed a predictable transitional type of behavior. The flour stress-temperature dependence was evaluated employing the relation: M where it is shown that composition can strongly influence the constant M. An empirical formula describing this effect is as follows: M = MI (equivalent at. pct Ni)-'" Some preliminay, tests were run on several commercial steels to test the generality of this relationship. One of the phenomenological explanations of the ductile-to-brittle transition encountered in bcc metals is based upon the difference in the temperature dependence of the flow and fracture stresses.' It states simply that the fracture stress is relatively insensitive to temperature and that the yield or flow stress rises rapidly with decreasing temperature so that, when the flow stress reaches the fracture stress, brittle fracture occurs without appreciable plastic deformation. This behavior is illustrated schematically in Fig. 1 where the ductile-to-brittle transition is shown to occur at two possible temperatures. The lowest temperature, TB, represents essentially completely brittle behavior while the higher temperature, TN, represents "notch" brittle behavior. Support for this theory is obtained when it is observed that fcc metals, which do not commonly have a ductile-to-brittle transition, also do not commonly exhibit any strong temperature de- pendence of the yield stress. This relationship of yield or flow stress behavior with the ductile-to-brittle transition has been generally observed for most metals representative of these two crystallo-graphic structures. One exception to this generalization appears in the case of tantalum where no apparent ductile-to-brittle transition has been observed. However, this may simply be an indication that this type of behavior is not directly related to the flow stress and that some other mechanism such as twinning must also be operative. A comparison of the typical temperature dependence of the yield stress of some representative metals is shown in Fig. 2. In the study of the temperature dependence of the strength of metallic materials, considerable ef-

Jan 1, 1963

By Craig R. Barreft, Oleg D. Sherby

The steady-state creep characteristics of pure polycrystalline copper were studied in the temperature range 400" to 950°C and in the stress range 400 to 7000 psi. Tests were conducted in dry deoxidized hydrogen and all specimens exhibited high ductility before fracture. Two activation energies for creep were established as a function of temperature. Above about T/T, = 0.65, the activation energy for creep was 48,000 cal per mole whereas between 0.5 and 0.65 T, it was 28,000 cal per mole. The observed temperature dependence of the activation energy for creep follows the same trend as exhibited by the self-diffusion coefficient of copper in copper single crystals and silver in silver single crystals. It is therefore believed that the rate-cmtrolling mechanism in creep of copper in the stress and temperature range studied is diffusion-dependent and is probably associated with a dislocation-climb process. The low activation-energy region is attributed to enhanced volume difFusion from the presence of dislocations which act as short-circuit paths for diffusion. THERE is extensive experimental evidence1,2 that the activation energy for creep, Q,, for pure poly-crystalline metals tested at temperatures above one half the absolute melting temperature (0.5 Tm) is a constant and equal to the activation energy for volume self-diffusion, Qsd This equality is generally interpreted as meaning that creep in this temperature range is controlled by a dislocation-climb process. The existence of high-temperature creep activation energies not equal to the respective self-diffusion values has been suggested both theoretically3"5 and experimentally.6-8 Two examples of apparent nonequality between Q, and Qsd have been reported for the cases of silver7 and copper,' where activation energies for creep much lower than those for self-diffusion persist to rela- tively high temperatures (up to 0.6 T,). These observations suggest that dislocation climb may not be the only important process in the high-temperature deformation of these metals. That dislocation climb does indeed occur relatively slowly in these two metals due to their low stacking-fault energy has been suggested by many investigators.9-10 Although the creep behavior of copper has been studied extensively at low temperatures, the high-temperature activation energy for creep is not well-defined. The data of Feltham and Meakin8 indicated that Q, is temperature-dependent above one half the melting temperature, equaling a value of -30,000 cal per mole at temperatures up to 550°C and increasing to a value of -49,000 cal per mole at 700°C. No data has been reported above 700°C. The value of 49,000 cal per mole is very near the value of Qsd for copper reported by Kuper et al." as 47,100 cal per mole. In view of the lack of high-temperature creep data and the apparent temperature dependence of Q, for copper the present investigation was undertaken to determine the value of Q, over the temperature range of 400" to 950°C. It was hoped that such a study would clearly document the temperature dependence of Q, and yield significant information as to the nature of the rate-controlling creep mechanisms. MATERIALS AND PROCEDURES The material used in this investigation was high-purity OFHC copper. After rolling and recrystal-lization treatments spectrographic and chemical analyses showed only 0.0008 pct Ag, 0.0002 pctCa, 0.0002 pct H2, and 0.002 pct O2 as trace impurities indicating a purity of greater then 99.995 pct. Specimens were machined from cold-rolled sheet and the gage sections polished with 2/0 emery paper prior to annealing treatments. Annealing was done in both vacuum and dry deoxidized hydrogen atmospheres. No variation in creep strength was found as a result of the different annealing atmospheres. The final annealing temperature was either 700°, 800°, or 1000°C depending on the temperature range to be studied. These treatments resulted in average grain diameters of 0.03, 0.4, and 1.0 mm, respectively. The precise mechanical-thermal history of these

Jan 1, 1964

By W. H. C. SIMMONDS

The mining, metallurgical, and petroleum industries can be viewed as financial or as social institutions or both. The differences between these two conceptions of their businesses will influence their environmental 'and social actions. During the next 10-20 years western industry will be subject to a drop in the growth of a more highly educated labour force and to the emergence of holistic economics, new national goals, and a new ecological perspective. The profitability of the mining industry may therefore be influenced by the human side of its business to a greater degree. The increasing human, social, and environmental responsibilities can be discharged by improving the miner's equipment; by learning to look at situations through the eyes of all those involved; by developing common 'languages' which governments and the public can understand; and by mediating where feasible on the international scene.

Jan 1, 1978

By J. B. Clark

In multiphase ternary diffusion studies, plots of the variation bf the composition on the isotherm constitutes one of the most effective methods of presenting experimental results, especially if such plots are made in a manner which relates the composition path on the isotherm with the diffusion layer structure in the couple. Unfortunately, if different conventions for plotting are used serious misinterpretations occur readily, causing apparent disagreement between investigators who actually share the same viewpoint. A common convention for mapping these diffusion paths is needed at this time because with the increasing use of the electron-probe X-ray microanalyzer, a much greater number of ternary diffusion studies can be expected in the near future. In an effort to prevent unnecessary confusion in the future litera- ture, a convention for these plots is proposed, as outlined below. A hypothetical example of the use of these conventions is given in Fig. 1 where the path of composition through the diffusion structure of the 100 pct A/50 pct B, 50 pct C couple is plotted on the appropriate isotherm of the ABC system. The lower case letters relate the region in the diffusion layer structure to the appropriate composition on the ternary isotherm. 1) The diffusion path is plotted on the isothermal section corresponding to the diffusion temperature of the couple. 2) The terminal compositions of the plotted diffusion path are the initial compositions of the couple halves—provided infinite boundary conditions are maintained. If, in either couple half, infinite conditions are not maintained, then the path terminates at the composition of the exterior surface of the couple. If, at this surface, the composition varies with time or if the plotted path is time dependent, then the diffusion time should be noted beside the plotted path. 3) A solid line crossing a single phase field (e.g., line a-b in Fig. 1) denotes an existing layer of that phase in the diffused couple. 4) A dashed line crossing a two-phase field parallel to the tie lines (e.g., line g-h) represents an interface between the two phases with interfacial compositions designated by the ends of the tie-line. The line represents no spatial extent. 5) A solid line crossing a two-phase field so as to cut tie lines (e.g., line b-c or line j-k) represents a locally equilibrated columnar two-phase layer. The solid line should cut those tie lines which correspond to the lateral interfacial equilibria along the columnar

Jan 1, 1963

By Marvin P. Barnes, John G. Simos

The Park City District, Utah, is situated in the Wasatch Range at the intersection of the westward extension of the axis of the Uinta Range. Ore has been mined almost continuously from the first discovery in 1869 to the present day, with a total production of over 14 million tons. Sediments of Carboniferous to Triassic age have been folded into the northerly plunging Park City anticline and subsequently modified by thrust faulting, diorite and diorite porphyry intrusions, and strong east-west normal faulting during the Laramide orogeny. Younger andesitic volcanics partially cover the eastern edge of the district. The ore bodies occur as both lode and bedded replacement deposits over widely scattered localities. Near surface, high-grade silver "bonanza" ores were mined in early days from the Ontario and Daly Lodes, which occur along the east-west zone of faulting near the center of the district. Other lode or fissure deposits were found along the Mayflower and Hawkeye faults to the east and southeast. Large bedded replacement silver-lead-zinc ore bodies associated with east-west zones of fissuring, have been mined from favorable horizons in the Park City Formation in the Daly West and Judge mines. A series of long, narrow, high-grade, replacement ore bodies occur in the Silver King mine at a single horizon in the Park City Formation. Ore is currently being mined from strong bedded replacements in the Humbug Formation near the apex of the Park City anticline. Factors controlling ore deposition are: magmatic source, structural feeder systems, and favorable host rocks. Ore deposition along favorable beds is primarily a function of physical conditioning and secondarily of chemical composition.

Jan 1, 1968

By Pat McCarran

WHEN this Government was founded, the framers of the Constitution wrote into that instrument a provision that Congress should "coin money and fix the value thereof;" and the Constitution prohibits making anything but "gold and silver" lawful money. So silver is written into our basic law. Shortly after President Washington took office in 1789 the Congress passed the first Mint Act, setting up the U. S. Mint. In that Act, signed by President Washington on April 2, 1792, the weight of the American dollar was fixed, and it was provided how much silver should be contained in a silver dollar and how much gold should be contained in a gold dollar. It was decided that 371 1/4 grains of pure silver was to be the standard dollar of America. That standard with respect to the pure silver content of the dollar has never changed.

Jan 1, 1947

By R. C. Earlougher

Jan 1, 1970

By C. G. Cheriton

The Bathurst mining district is located near the town of Bathurst on the north shore of the province of New Brunswick in eastern Canada. This region is the northeasterly extension of the Appalachian mountain system. The area is heavily forested and covered with a fairly uniform layer of glacial gravels and boulder clay. The relief is low, increasing to a few hundred feet in the north west and several hundred feet in the extreme southwest. Thus, rock outcrops are scarce and occur mostly along streams and ridges. These factors made conventional prospecting difficult and resulted in the district becoming an excellent place for the application of regional geological studies, air photo techniques, airborne and gound geophysical methods and soil sampling. Late in 1952, The Brunswick Mining and Smelting Company discovered a very large base metal sulphide body presently known as their No. 6 orebody. Early in 1953, another and even larger sulphide body was discovered and is known as the No. 12 ore body. Mining exploration was very active thoughout 1953 and in 1954, The American Metal Company discovered the orebodies which have been developed into The Heath Steele 'Mines. The location of these deposits is shown on figure one. In the latter part of 1954, The Anaconda Company became interested in the district and decided to make a geological study of this new and promising base rrietal area. The following paper presents the story of the application of modern geological and geophysical techniques, leading to the discovery of a large sul-nhidp liodv. The Bathurst district is generally underlain by the Tetagouche group of Middle Ordovician rocks.

Jan 1, 1961

How Mining Engineers Will Fare in 1977 Mining Education- The State of the Discipline Coal Mining Technologists are a New Force in the Labor Pool Trained Manpower Provided by Mining Technology Programs Putting New Engineers to Work-A Management Perspective

Jan 1, 1977

By A. Lawley S. Schuster

The tensile behavior of copper foils prepared from rolled bulk material has been studied over the thickness range 2 to 53 , and for a range of pain sizes. For foils of comparable grain size, having the cube texture and tested along (100), yield strength increases with decreasing foil thickness t below -26p, with a corresponding decrease in ductility. Deformation occurs in the form of localized slip clusters distributed throughout the gage section. To the extent that the tensile strength (10 to 18 kg mm-) is unaffected by foil thickness, and that the foils possess fair ductility, the stress-strain behavior resembles that of bulk material rather than that of whiskers or evaporated films of comparable dimensions. The dependence of yield strength o on foil thickness t below -26p is of the form: oy = oo + kt-1/2. Possible explanations for the stress increase are considered based on 1) the dependence of active dislocation source length on foil dimensions, 2) the locking of surface sources, or the blocking of mobile sources at the surface due to surface film. It is now well-established that filamentary whiskers of many materials show exceptionally high strength compared with bulk crystals.'-11 As the diameter of the whiskers decreases to -1, the observed fracture strength approaches, and in certain cases exceeds, the calculated shear stress for the nucleation of slip in a perfect crystal.' In general, the stress-strain curve is entirely elastic, with strains at fracture approaching 1 pct. Similarly, thin films12-24 of evaporated or electrodeposi-ted material have been shown to possess tensile strengths three to seven times that of bulk material, with total strains at fracture -1 to 2 pct. In the present study, attention has been directed to the room-temperature tensile behavior of thin foils of copper over the thickness range 2 to 53, prepared from rolled bulk material. Yield stress, ultimate tensile strength, elongation to fracture, and work-hardening behavior are measured as a function of grain size and foil thickness. Structurally such foils are superior to either evaporated or electrodeposited films, and in the recrystallized condition exhibit considerable ductility. Apart from preliminary work by Sumino and Yamamoto25 on the work-hardening behavior of rolled and recrystallized copper foils, no systematic tensile studies have been carried out on material of this form. EXPERIMENTAL PROCEDURE Tensile specimens were prepared from 99.995 pct purity rolled copper foils of thickness 2, 6, 12, 26, and 53, obtained from the Hamilton Watch Co., Lancaster, Pa. Irrespective of specimen shape, it is necessary to use tensile foils with edges free from notches or tears. To this end, any form of cutting operation was excluded, and the tensile foils prepared using a photoengraving process, the details of which are described elsewhere.26 Since tensile data are required under conditions of uni-axial stress, the specimen shape is extremely important. Ideally, the foil should be infinitely long, allowing a gradual taper from the grip area to the gage section; however, from a practical standpoint, long foils are easily damaged during testing. A modified tensile specimen was therefore selected having a parallel gage section 1.25 by 0.20 in. with a tapered shoulder section increasing to 0.5 in. at the grips, and an over-all length between grips of 4 in., Fig. 1. In practically all tests, these foils fractured within the parallel gage section. By approximating the foil contour (Fig. 1) to a hyperbola it is possible to analyze the stress distribution in the tensile foil using two-dimensional elasticity

Jan 1, 1964

By Arthur F. Hagner

The titaniferous magnetite deposit at Iron Mountain, Wyoming, is in Precambrian anorthosite. Individual ore bodies are lenses, commonly arranged en echelon, conformable to the platy crystal structure and compositional layering of the anorthosite; a few transect these features at various angles. The ore bodies are on the east flank of the principal anticline in the anorthosite mass. Magnetite and ilmenite, accompanied by spine!, are the ore minerals. The principal gangue minerals are olivine, which was introduced with the ore, and plagioclase, the chief constituent of the anorthosite. The anticlinal region appears to have been a structurally weak zone, and westward-bowing curves of the axis were especially favorable sites for localization of the two largest massive ore bodies. These bodies are synclinal and plunge southeast. The proportion of magnetite-ilmenite to olivine and to anorthosite appears to be related to structural features. Where magnetite-ilmenite is present with olivine, the magnetite-ilmenite is encountered along the most pronounced parts of a fold where anorthite content is highest, whereas olivine is associated principally with more gently folded portions. During granulation and recrystallization of the anorthosite mass, temperature and pressure changes furnished the energy required to release and mobilize iron and other elements that migrated to areas of low pressure, the ore zone. Some iron and magnesium may have combined with silica from partly dissociated plagioclase to form olivine. The ore formed by replacement of anorthosite as indicated by: (1) the marked changes in mineralogy along strike, dip, and plunge of an ore body; (2) the concentration of massive ore in folds and olivine on limbs; ( 3) the halo of low-grade mineralized rock that transects the structure of the anorthosite in the hanging wall; and ( 4) the layering in the large southern ore body, that strikes more easterly than the trend of the body.

Jan 1, 1968

By Joseph Moses Botbol

In passing the judgments essential to his trade, the geologist may be assisted by two new methods. These will enable him to (1) arrange the minerals of a selected group of base metal mining districts in the order of their typicalities and (2) compute the degree of mineralogic association between the model so derived and a district external to the model. It must be remembered, of course, that the methods discussed in this article are no more powerful than the structure of the model used and the data available. The geologist who employs these techniques must still exercise his expertise

Jan 1, 1970

By Gregory M. Dexter

Recent litigation in Pennsylvania between three coal-mining companies and a private water company resulted in the payment by the coal companies of the equivalent of about $500,000 to buy a new water supply to replace that which had been damaged by acid drainage from strip mining. An investigation of the relevant facts indicates that the water could have been treated by spending about $40,000 on equipment and $15,000 yearly for chemicals, labor, and power until the contamination could be reduced about 80 pct. The water company's supply, furthermore, had deteriorated largely by reason of dry weather before stripping was begun by the coal companies. Payment to the water company should not have exceeded $300,000 and could have been as low as $100,000. Strip mining of coal is common in Pennsylvania. The most important objection to it in Pennsylvania is generally acid pollution of runoff water. An outline of the methods, therefore, that could be used to reduce such pollution, to compare acid-contaminated waters, and to treat such waters to make them satisfactory for public and industrial use is worth-while. The watershed of the West P~M Water Co. covers about 4.5 square miles, 20 miles west of Pittsburgh, and has two 90,000,000 gal reservoirs sup- plying about 1,300,000 gal daily for public and industrial use of which 450,000 gal daily are for two railroads. The pollution arises from weathered derivatives of typical "Coal Measures"

Jan 1, 1949

By W. R. Hibbard

Evidence is presented which confirms previous findings that models of solution strengthening depending solely on lattice parameter changes are incomplete. Direct evidence for the Suzuki interaction of chemical effects was obtained from alloys with constant lattice parameter, for which solution strengthening was nearly independent of temperature from 300° to 20°K. SOLUTION hardening principles have been reviewed recently by Parker and Hazlett.' In addition, the interactions of dislocations and solute atoms were reviewed by Cottrell.' It is not proposed to review this information again here, but to refer only to those details which are pertinent to the developments which have occurred since these papers were published. Literature Survey To set the stage, it has been known for some time that solid solutions are stronger than the pure parent metals, and that the strength increases with increasing amounts of alloying element. One of the most extensive earlier investigations was that of Lacy and Gensamer,3 who reported that the solid solution strengthening of iron is a power function of the composition, that the relative strengthening is a function of the solubility limit, and that the rate of strain hardening is a function of the amount of solution hardening. Thus, the slope of the plastic portion of the stress-strain curve increases with increasing yield strength. An approach to the development of principles resulted from work by Gulyeav,4 who reported that the strengthening effect of solid solution alloys is periodic in character when plotted as a function of the atomic number of the solute. A more quantitative approach was to relate the amount of solution hardening to the lattice parameter of a solid solution. This was done quite early by Norbury,5 and later by Brick, Martin, and Angier,6 Frye and Hume-Rothery,7 and French and Hibbard. This relationship is only approximate in character. The next development was to relate the amount of solution hardening to lattice stress, as proposed by Frye and co-workers.9 They calculated what they called ionic overlap from the lattice parameter changes represented as a change in volume, using Bridgman's hydrostatic compression equation. The resulting correlation was somewhat improved as compared to the simple correlation with lattice parameter. The next step was carried out by Dorn, Pietrow-sky, and Tietz,10 who suggested an effect of valence differences in addition to the effect of lattice parameter. Their proposed parameter shows flow stress as a single valued function of the concentration and a relationship involving these two atomic variables. In addition, they contributed new data on the temperature dependence of solution hardening which indicated that it was a strong function of temperature for aluminum alloys. Allen, Schofield, and Tate11 carried the valency effect even further by reporting data indicating that with a given solvent element the stress-strain curve is a function of electron density, entirely neglecting the size factor, which varied by a factor of two. This evidence led to a quantum mechanical calculation by Cottrell, Hunter, and Nabarro,12 based on the formation of a dipole around an edge disloca-

Jan 1, 1959

By John Chipman, Wayne L. Worrell

Using recent thermodynamic data for the carbides and oxides of tantalum, columbium, and vanadium, the stable solid phases aboue 1300°K and at 1 atm CO(g) pressure in each M-C-O system have been determined. Pourbaix-Ellingham diagrams have been constructed and are used to estimate the minimum temperatures necessary to obtain these metals by carbothermic reduction under reduced pressures. TANTALUM, columbium, and vanadium react with carbon to form the M,C and MC carbide phases. The M,C carbides have narrow homogeneity ranges, but the MC phases possess considerable ranges of homogeneity.' The free energies of formation of the MC carbides were recently measured, and those of MC and M2Ccarbides have been estimated., (The notations MC and MC denote, respectively, the carbide compositions at the carbon-rich and at the metal-rich boundaries of the homogeneous MC phase.) In this paper, these carbide data are combined with thermodynamic data for the oxides to predict the stable phases in the Ta-C-O, Cb-C-O, and V-C-O systems at specified temperatures and oxygen pressures. M-C-O PHASE DIAGRAMS The solid phases in equilibrium above 1300°K for each M-C-0 system are shown in Figs. 1, 2, and 3. Above 1300°K, the vapor would consist entirely of carbon monoxide; and these phase diagrams were obtained by specifying the vapor pressure of CO(g) to be 1 atm. The temperature at which any two solid phases become unstable is specified along the two-phase equilibrium lines in each diagram. To simplify the diagrams, all solid phases in the Ta-C-O and Cb-C-O systems are represented as stoichiometric compounds. However, the homogeneity ranges of VO and VC are indicated, because they form a complete series of solid solutions.3 It also should be noted that the homogeneity range of

Jan 1, 1964

The income of the Institute is derived mainly from dues, advertising in MINING AND METALLURGY and sale of publications. These sources are fortunately supplemented by the interest from invested funds now amounting to over $500,000, a considerable portion constituting endowments for especial purposes. Aside from the medal funds the principal endowments are the James Douglas Fund for support of the Library, the Rocky Mountain Fund and the Seeley W. Mudd Memorial Fund. The income from the two last named is available for the support of research and a variety of other purposes. It is allocated by the Board of Directors upon recommendation of standing committees in each case. An active effort is being made to increase the endowments of the Institute, it being felt that unusual opportunities exist for research and public and professional service through the organization.

Jan 1, 1939

By O. E. Palasvirta

Several drum-type, low-intensity dry magnetic separators have recently been described 1,2,3,4 all of which share at least two generic similarities. The magnet consists of a multiplicity of poles of alternating polarity and, the speed of the drum shell, relatiw to the magnet, is such that the magnetics are agitated through rotation of the magnetic particles around their individual axes. The speed of the drum relative to the magnet (differential speed) determines the frequency of the field reversals. For effective agitation this frequency generally has to be above a specific value, which varies according to the mean particle size of the magnetics. With separators of small diameter, say less than 11/2 ft., a sufficient differential speed for treatment of fine magnetite can be attained only by rotating both the magnet and the drum separately; separators of large diameter may attain sufficiently high differential speeds with stationary magnets. Separators of large diameter thus have the advantage of simplicity of design. The capacity of a separator of this type is directly proportional to the speed of the shell. As the centrifugal force opposing the magnetic force increases at a slower rate than the peripheral speed of the shell when drum diameter is increased, large drums can be operated with higher peripheral speeds. Thus they have a higher capacity than smaller drums. Separation is also a statistical phenomenon, i.e. the grade of concentrate improves as the number of agitations or rotations of the magnetic particles per separation increases. As separators of large diameter have space for a large number of magnets they are best suited for production of optimum grade concentrate. The statements above are general clues For separator design. In the following an expression IS derived showing a more exact relationship between the pertinent separator variables. As both magnetic attraction and centrifugal forces are directly proportional to the volume of the affected bodies, complications in mathematical analysis, arising from variable particle size, are avoided by considering the force per unit volume of affected material. For the magnetic force per unit volume Runolinna (3) gives the following equation: V " 1 + N(ur, - 1) uo dr (1) where ur and uo stand for the relative permeability and the permeability of vacuum, respectively, N is the demagnetization factor, B the intensity of the magnetic field, and r the distance from the face of the magnetic pole. The permeability of a specific magnetite ore can generally be considered as a constant. For ground, liberated material N can also be treated as a constant, and the first simplification can be made by writing ur-1 1=k1. 1 + N(ur - 1) uD k1. Fig. 1 shows the field intensity curves for two U-magnets of different size, but of roughly similar geometry of cross-section as plotted against the distance from the plane of the pole faces. The curves

Jan 1, 1961

By AIME AIME

THE twenty-second annual meeting of the Canadian Mining Institute was held at the King Edward Hotel, Toronto, on Mar. 8, 9, and 10, and was followed on the 11th by an all-day excursion to the International Nickel Refinery at Port Colborne. The meeting was very well attended and dealt with some of the most important matters, both technical and economic, that have ever come before the Canadian Institute. The question of licensing engineers is before the Canadian members as it is before our own in this country and the attitude of the mining engineers across the border is like that of the American mining engineers, opposed to the licensing of the mining. engineer, however they may feel toward the licensing of other branches of the engineering profession. It was well pointed out that such a law, had it been in existence in the last decade or two, would probably have prevented the rapid development of Canada's mines. Whereas one civil engineer can run a line of survey as well as another, perhaps, it is only a question in his case of whether he can or cannot survey. In the case of a mining engineer employed by a man with capital to invest in a development project, unless the man with the money has confidence in the judgment of his engineer the fact that he is a professional man would carry little weight in inducing a large investment toward the development of Canada's resources. It was also pointed out that although the Institute as a whole had not passed on the matter, it would probably be opposed to legislation aiming only for self-interest, but would be heartily in accord with legislation which could be shown to be for the service of the community at large.

Jan 1, 1920

By Bert S. Sandell

Much has been said and written about the various uses of die castings, their applications in the various industries and their advantages and disadvantages. Examination of this literature, however, fails to disclose any data concerning the effect of temperature upon any of the physical properties of die-casting alloys. The uses and applications of die castings are so numerous, and of such a varied nature, that far too lengthy a manuscript would be required to list all of them. Brief mention of some specific cases will suffice to illustrate the temperature ranges in which certain die castings function. Automobile hardware, such as hub caps, door handles, radiator caps, etc., can be used as one example. Castings of this type are constantly exposed to varying climatic conditions, temperatures ranging from below zero to upwards of 100" F. Refrigerator parts, such as ice-cube trays, etc., form another example. Approaching the other temperature extreme, we encounter conditions such as are found in kitchens in which oven-heat indicator parts, cooking utensils, waffle grids, etc., embody use of die castings, where temperatures as high as 500" F. are often met with. Because of this variation in service temperatures, it was felt necessary to ascertain the effect of these temperatures upon the physical properties of die-casting alloys. The Charpy impact test was chosen first because of its simplicity, and because of the fact that brittleness is more likely to be objectionable in die castings than hardness or other physical properties. Alloys Investigated Two types of alloys were used in this investigation—zinc-base and aluminum-base alloys. Two alloys of each group were included. Those most generally employed in the industry at present were selected. Alloys A and B are of the same nominal composition, and correspond to A. S. T. M. alloy XXI, containing 4 per cent aluminum, 3 per cent copper, 0.1 per cent magnesium, and the balance zinc of 99.99 per cent

Jan 1, 1932

By R. F. Mehl, B. Lustman

The formation of intermediate phase layers in cementation processes has been subjected to extensive qualitative investigation though to relatively little quantitative study; this work has recently been fully summarized by F. N. Rhines.' It is necessary here only to cnumerate the general conclusions drawn concerning the kinetic laws governing the growth of intermediate layers and to state what is known concerning the structural changes accompanying the generation of phase layers. I. When the intermediate phase is protective in type—i.e., when its density is less than that of the base metal, so that a continuous coating is formed and maintained—the isothermal growth of the phase follows a simple parabolic equation: X2 = kt [i] where X is the thickness of the alloy layer, k thc reaction rate constant, and t the time. The applicability of this equation to diffusion processes is tested by plotting the square of the thickness versus time, or by plotting the thickness versus the square root of time; the resultant achievement of a straight line in such a plot has been considered sufficient proof of the validity of this equation. Exceptions have been found where liquid phases are involved in the reaction, where the diffusion layer is cracked,2 and where thin semimetallic oxide and sulphide coatings are formed on metals.$ In the first two cases the thickness increases linearly with time, and in the latter it is a logarithmic function of time. 2. The rate of thickening varics with temperature according to the Arrhenius equation: k = Ae-Q/RT [2] where k is the parabolic rate constant of Eq. I, or some other rate-descriptive function, A is the action constant, e the base of natural logarithms, Q the heat of activation, R the gas constant, and T absolute temperature. This equation has been found to be generally valid except when transformations occur during reaction in either the base metal or in the reaction layer; in such instances Eq. 2 is still applicable with different values for the constants A and Q above and below the transformation temperature. 3. Ali phases that are stable at the temperature at which diffusion occurs will appear in the interdiffusion of two components. In some cases certain of the phases may be too thin to be observed and identified easily. Nonequilibrium phases have never been noted in thick reaction layers; i.e., layers of a thickness that may be discerned microscopically. The relative thickness of each phase in a diffusion layer is proportional to the concentration gradient and to the rate of diffusion in that phase.4 The reaction layers tend to have a

Jan 1, 1942