Search Documents

By Joseph Nawrocki, Margaret Hettinger, Dr. Catherine Johnson

"Optimized rock fragmentation is essential for minimizing downstream costs to mining operations.Photographic fragmentation analysis, vibration monitoring, and high-speed video all providemeasurements of blast effectiveness and supply data that allows operations to modify blasts to achieve downstream goals."

Jan 1, 2016

By P. Perruzza, R. Grandori, A. De Biase, A. Ciamei, A. Busillo

The Turin metro alluvium soil is mainly made of large boulders, cobbles and gravel , few sand and almost no fines. This grain size curve is out of the range of application for EPB and Slurry TBMs. In order to bore 5 of the total 7,5 kms of Line 1 tunnel, two specially designed Lovat EPB TBMs were utilised in combination with a systematic non structural pre-grouting of a small volume rectangular slab just above the tunnel section. The same pre-grouting was not however applicable for lack of access on surface in some sections of the remaining 2,5 km of tunnel that had to be bored below important buildings/structures, with under ground water pressure up to 1,5 bar, with curves radius of 180 m only. For these more critical sections it was necessary to study and implement a new technical solution and improve the capacity of the TBM to work efficiently in EPB mode even in this unsuitable ground and overall conditions. After months of studies the selected and adopted solution has been to inject inside the cutterhead chamber, in addition to the almost standard foams & polymers additive mixes, a suspension of limestone powders. This with the scope of compensating the lack of fines of the natural ground with rock powders.

Jan 1, 2005

By Luis Haro

Puesto que el deslizamiento de relaves constituye uno de los principales riesgos para la vida y seguridad de los embalses, se desarrolló un programa que rehabilite los depósitos de los relaves a través de los gaviones y geomallas como elementos que estabilizan los relaves descargados. En este sentido, el uso de geosintéticos revolucionó el diseño de los relaves y sistema productivos y permitió un mejor manejo ambiental de los relaves. Asimismo, la utilización de gaviones como paramento externo en el sistema suelo armado, otorga mayor rigidez al mismo en el caso de paredes, taludes más verticales, drenaje y protección contra la erosión. En consecuencia, el uso de gaviones y geomallas es aplicable para la construcción de depósitos de relave y estabilización de depósitos inactivos.

Sep 13, 2001

By Zbigniew J. Hladysz

A Deep Underground Science and Engineering Laboratory (DUSEL) is being planned at the site of the former Homestake Gold Mine in Lead, South Dakota, under the sponsorship of the US National Science Foundation (NSF) in cooperation with the US Department of Energy (DOE). This national facility will host a variety of multidisciplinary science and engineering experiments including physics experiments that require shielding from cosmogenic radiation. Geotechnical mapping was performed in 2010 in large excavations of the Davis Campus at the 4850 Level of the former Homestake Mine. LIDAR mapping included laser scanning using a red light laser scanner and 288 Mpixels 360° still camera. The resulting vector map with the photographs digitally draped over the model, was used to create an accurate, virtual model of the excavations. For model verification, the laser scanning was accompanied by surveying and manual mapping of the geology and rock structure. The immediate use of the model was to perform structural analysis and interpretation of geology needed for the design of the DUSEL?s super large excavations. The second round of scanning, after the application of shotcrete to the excavations walls, will be used as a technical blueprint to assess the effectiveness of shotcrete application.

May 1, 2011

YOUR Excellency, Fellow Members of the Australasian Institute of Mining Engineers and Gentlemen:-Nearly a decade has passed since our Institute first met in New Zealand. May I, at the very outset of this second gathering, congratulate the Institute on the great progress that has been made in the interval. At the first meeting in New Zealand in the year 1903, I understand that less than 20 persons were present, and now in the large concourse before me I believe there are not fewer than 140 persons, while if every member of the Institute to-day where here there would be over 500 with usagreat change from a membership of only 250 in 1903. I feel deeply appreciative of the honour you have conferred upon me by electing me your President for the year 1911. In return for the compliment, may I ask you to believe that I shall do everythingin my power to further the interests of the Institute throughout the coming year.It is a great regret to me to realise that soon my work in New Zealand will be over. However, I trust that the new...

Jan 1, 1912

By Charles E. Green

This study was conducted to identify, evaluate, and develop procedures to minimize or eliminate safety hazards associated with the electrokinetic dewatering process, such as toxic and volatile gas emissions, electrical shock, accidental detonation of explosives, electrochemical corrosion of metal appurtenances, and possibly others. The identification, evaluation, and procedure development were based on pertinent literature, existing safety regulations, interviews with mine personnel, physical and mechanical properties of the electrokinetic dewatering process, and physical characteristics of the material to be dewatered. The electrokinetic dewatering process was described in detail. Potential safety hazards were identified and evaluated. Procedures and/or safety regulations were developed to minimize or eliminate the potential hazards. It was recommended that the electrokinetic dewatering process when used in deep metal mines be properly monitored to obtain additional information on other potential hazards that possibly exist.

Jan 1, 1979

By S. Suwansawat, D. J. Maconochie, C. C. Chang

This paper describes the overall delivery of the tunneling for the Mass Rapid Transit Authority of Thailand’s Chaloem Ratchamongkhon Line in Bangkok and the constraints provided by the alignment. Eight earth pressure balance tunnel boring machines were employed under two major civil works contracts to drive approximately33 kilometers of tunnel in soft saturated ground beneath the crowded streets of Bangkok. Responsibility within the contract for building damage provided an inherent control for ground movement arising form tunneling when the right of way was narrower than the influence zone. These limits affect the earth pressure balance requirements and permissible ground loss. The methods adopted to limit ground movements and deal with the various obstacles to tunneling influenced the design and operation of the machines. The challenges provided by the need to tunnel through numerous lines of piled foundations of canal bridges and overpasses crossing the alignment are described.

Jan 1, 2001

By J. K. Whyatt, B. G. White

A comprehensive survey of mine seismicity and rock bursting during development of two sublevels at the Lucky Friday Mine, Mullan, ID, USA, was conducted to better define rock failure mechanisms and sources of ground control hazards. Survey data included rock burst damage reports, seismic event locations and magnitudes and, for the most energetic events, first-motion information. Several subsets of this database, including large seismic events, rock bursts, and microseismic activity near the face, were analyzed. Elements of the large-event and rock burst data sets were nearly independent. That is, there was no relationship between the risk posed by a seismic event and its energy, although such a relationship is well established for the mine as a whole. All data sets showed that certain geologic features appear to control the spatial distribution of events and the spatial distribution of rock burst risk. The data also suggest that, within the scope of this study. the greatest risk of injury occurs when a pocket of heightened rock burst risk is first encountered and that this risk is controlled when miners adapt their practices to these conditions. Recognition of the role of particular geologic features in the spatial distribution of rock burst hazards provides an opportunity for anticipating, rather than only reacting to, a changing level of rock burst hazard- However, much work will he required to make good on this promise.

By D Craw

Sulphur-rich minerals such as authigenic pyrite (FeS2) are commonly associated with coal mine workings. Metallic elements such as arsenic (As), copper (Cu) and zinc (Zn) are enriched in the pyrite relative to their concentrations in the surrounding environment. Exposure of pyrite and coal to air and water results in a series of oxidation and hydrolysis reactions that are commonly catalysed by species of Thiobacillus bacteria. These reactions lead to a lowering of the pH in the drainage waters (acid mine drainage, AMD) and subsequent mobilisation of trace metals in environmentally significant concentrations. This study assesses the spatial distribution of As, Zn and Cu concentration in water in relation to pH and Eh (redox potential) downstream from the tailings at the Wangaloa opencast lignite mine in southeast Otago. This mine was abandoned in the late 1980s due to a decrease in the economic viability of mining the lignite. The area is showing the characteristic symptoms of AMD, which is detrimental to the health of several Pinus radiate growing on some of the tailings. The pH of the drainage waters can get as low as 2, and in some instances, lower, but it returns to near neutral (pH 6.5) up to 200 metres down stream from the base of mine waste piles. It is well documented that the atmospheric oxidation of pyrite is catalysed microbially, causing a substantial decrease in the pH of the drainage waters. Acidification is then counteracted predominantly by natural abiotic remediation processes occurring downstream.

Jan 1, 1999

By J A. Singer, S R. Iverson, C A. Link

High resolution seismic refraction tomography has proved to be a useful tool to effectively estimate depth of blast induced damage in a mine face. Excavation blast damage can be as shallow as 1 to 2m and requires resolution at a fraction of a meter for effective imaging. We used an accelerometer with flat frequency response to 1000Hz to record data at spacings of approximately 0.25 to 0.5m along mine walls. First arrival times from the seismic data were used to produce P-wave velocity tomograms. The tomograms show transition from low velocity zones to velocity associated with competent rock. We interpret the low velocity zones to indicate residual fracturing from blasting. Experiments on a concrete test block and at two underground mine locations give results that are consistent with fractured rock transitioning to competent rock. Our method can be applied efficiently in an underground environment to provide continuous velocity information with depth into a mine wall over a span of approximately 10m.

Jan 1, 2009

Accurately estimating load distributions and ground responses around underground openings play a significant role in the safety of the operations in underground mines. Adequately designing pillars and other support measures relies highly on the accurate assessment of the loads that will be carried by them, as well as the load-bearing capacities of the supports. There are various methods that can be used to approximate mining-induced loads in stratified rock masses to be used in pillar design. The empirical methods are based on equations derived from large databases of various case studies. They are implemented in government-approved design tools and are widely used. There are also analytical and numerical techniques used for more detailed analysis of the induced loads. In this study, two different longwall mines with different panel width-to-depth ratios are analyzed using different methods. The empirical method used in the analysis is the square decay stress function that uses the abutment angle concept, implemented in pillar design software developed by the National Institute for Occupational Safety and Health (NIOSH). The first numerical method used in the analysis is a displacement-discontinuity (DD) variation of the boundaryelement method, LaModel, which utilizes the laminated overburden model (Heasley, 1998).

Jan 7, 2020

By François Robichaud

"The Laronde mill has been in operation since 1988. Actual milling rate ranges from 7,000 to 8,500 mtpd. Laronde uses SAG/ball mill grinding followed by copper and zinc flotation circuits. A cyanidation/Merrill-Crowe process recovers the remaining gold and silver in the flotation tails.In 1999, the carbon in pulp circuit was replaced by a Merrill-Crowe circuit in order to cope with a much higher ratio of silver/gold associated with the discovery of the Penna shaft. Marine type diatomaceous earth was used as filter aid in both clarifier pressure leaf filters and recessed pressure filter presses from 1999 to 2005. In 2005, this filter aid was gradually replaced by alpha-cellulose after several laboratory and plant filtration trials. The selected cellulose is considered to be much less sensitive to parameters such as pH and reagent concentration and have increased clarifier and filter press filtration performance. Also, since cellulose is exothermic, replacing diatomaceous earth with cellulose as filter aid in the filter presses has increased calcining and oxidation rates in the calcining ovens since cellulose is exothermic. Finally, better calcining conditions have resulted in energy and reagent savings at the arc furnaces.This paper describes how the filter aid replacement has contributed to increasing productivity and Net Smelter Return of the refinery while reducing worker’s hazards and operating cost.INTRODUCTIONAll Merrill-Crowe circuits in the world are operated with filter aids. For years, the market for precoat filter aid has been dominated by mineral filter aids such as diatomite and perlite. Flowsheet and equipment selection at the Laronde refinery were performed in the late nineties. At that time, some key parameters of the design criteria had clearly identified marine type diatomaceous earth (DE) as the most successful filter aid. Parameters such as reagent cost and availability, clarity of the filtrate solution and good historical filtration performance in other concentrators had designated DE as the best suited filter aid. Pregnant solution processed in the refinery from its start-up through 2001 was fairly stable in flow rate and reasonable in terms of impurity content (cationic and anionic compounds)."

Jan 1, 2007

By G. T. Adel, J. D. Miller, C. L. Lin

Washability analysis determines the maximum separation efficiency that can be achieved in the operation of coal preparation plants. Unfortunately, there are no on-line techniques for determining this most fundamental information. It now appears possible to determine coal washability on-line through the use of x-ray computed tomography (CT) analysis. This paper presents the results for the development of a CT-based, on-line coal washability analyzer. The development of appropriate hardware and software necessary to adapt a CT analyzer for use in determining coal washability is discussed. Testing of the analyzer using well-characterized coal samples is presented.

Jan 1, 2000

By Sara Jane Boles

In recent years the demand for products of greater refractoriness has placed an ever-increasing emphasis on ceramic materials, including the metallic oxides. Magnesia (MgO) is one of the most important of these oxides, exhibiting, as it does, high electrical resistivity, high slag resistance, and a melting point of 2,800° C. However, magnesia has a tendency to hydrate in the presence of water and to volatilize above 1,500° C. in certain kiln atmospheres and has a comparatively low resistance to thermal shock. Because of these disadvantages, the previously listed advantages inherent in this material have been largely overlooked, and research on magnesia has lagged behind that on oxides such as alumina and zirconia. This bibliography has been prepared in an effort to present to Government and industry a comprehensive picture of the prospects for greater utilization of magnesia as a refractory material in future research. To provide as selective and accurate a collection as possible, the references included cover magnesia in a pure state, not as an additive or in combination with other materials. However, several references discuss the effect of minor impurities (less than 5 percent of the total) on the properties of magnesia, as these papers are considered to be of special importance. A few references to articles on forming techniques are also included, as they are valuable additions to the overall treatment of the subject. The processes used in obtaining and refining the raw materials are adequately covered in earlier publications and are excluded. A number of references are omitted as being of questionable value in enhancing the cumulative study of pure magnesia as an ultra-high-temperature refractory material.

Jan 1, 1962

By C. Sun

The Leeville underground mine has been in operation since 2006 and currently produces 3,200 tons of ore per day with an average gold grade of 0.4 opt. The mine has a large horizontal extent of 2,500 feet by 500 feet and a vertical extent of 20 to 200 feet. High density of joints occurs within the host rock. Based on Rock Mass Rating and field observation, the Leeville ground conditions are characterized as poor to very poor. As such, heavy ground support is required for the mining operation in Leeville. Ore zones with a height in excess of 10 m (35 feet) are considered for longhole stoping. A typical stope measures 6.0 m (20 feet) wide, 30 to 55 m (100 to 180 feet, depending on the ground conditions) long and 10 to 30 m (35 to 100 feet, depending the thickness of ore body) high, yielding 10,000 to 20,000 tons when completed. Narrow ore zones, less than 10 m (35 feet), are mined using cut and fill. These drifts are 4.6 m (15 feet) wide by 4.6 m (15 feet) high. Based on the afore-mentioned poor ground condition, the establishment of a ground control monitoring system is key to operating both safely and successfully. The ground control monitoring system is composed of comprehensive instrument design and installation. Instruments include Multi-Point Borehole eXtensometers (MPBX) and Stretch Measurement to Assess Reinforcement Tension (SMART) cables. The monitoring system covers the mining zones and infrastructure openings. After about two year?s applications and measurements, useful data has been and continues to be collected to use in future stope and infrastructure structure design. The system provides the information making engineer and operation teams to do their job more confident and efficiency. Keywords: Ground control, Monitoring system, Long hole stope, Instrumentation.

Jan 1, 2009

The Bureau of Mines has reviewed those portions of the "Tariff Schedules of the United States Annotated 1963" that are of interest to the minerals industry. This study shows to what extent rates of duty were altered (increased of decreased), and provides a bridge where possible from the old Schedule A classification system to the new TSUS system of statistical reporting of import data. In general the new tariff has corrected previous classification defects and inconsistencies, but the rates of duties have not been materially changed.

Jan 1, 1965

By R. A. Lord, H. M. Prichard

Paper presented at Mineralisation in the Caledonides, the Mike Gallagher memorial meeting held in Edinburgh, 27-28 June 1996. The complex exemplifies a class of olivine-rich, platiniferous ophiolite complexes generated by unusually high degrees of hydrous melting above a subduction zone. Crystallisation of abundant olivine from unusually picritic magmas produced an exceptionally thick sequence of crustal dunite cumulates. Significant (1-4 ppm) concentrations of Pt+Pd occur where sulphide-bearing dunites are spatially associated with podiform chromite concentrations. In the area north of the Balta Sound, the chromitites appear to lie in distinct stratigraphic zones. A detailed programme of lithogeochemical and soil-rock interface geochemical exploration led to the intersection by diamond drilling of three stratiform horizons of sulphide-bearing dunites and associated precious-metal mineralisation. Patterns of cryptic geochemical layering, at scales from 200 m to less than 1 cm, suggests open-system fractionation

Jun 19, 1905

By W. McMahon

Following the Sago Mine accident, the Mine Safety and Health Administration (MSHA) asked the U.S. Army Engineer Research and Development Center to study several possible methane explosion scenarios in the Sago coal mine. The study used a 1-ft resolution map of the mine to produce a 3-dimensional (3-D) model of a portion of the mine, including the sealed area where the explosion occurred. An advanced 3-D computational fluid dynamics (CFD) code was used to calculate the explosion pressures within the sealed area, on the mine seals, and in nearby regions of the mine. Based on the best available information on methane concentrations and assumptions on homogeneity and on layering and mix composition, three separate initial conditions of methane-air concentrations and location were studied. This paper discusses the CFD modeling technique, the results of the calculations, the challenges of conducting this type of modeling, and the advantages and limitations of CFD modeling of accident investigations of mine explosions.

Jan 1, 2009

By Gang Chen

This paper explores the possibility of using short-term time-dependent plate loading tests to estimate the elastic and viscoelastic parameters of the weak floor strata typically associated with coal seams in Illinois. Plate loading tests with incremental loads, similar to incremental creep experiments, were conducted until the floor failure occurred. For each increment, the load was held constant for a period ranging from 1-4 hours until a constant deformation rate was achieved. The deformation-time data were analyzed for viscoelastic parameters of weak floor strata assuming its behavior to be adequately represented by the standard Burgers model. The analysis required development of mathematical equations for the time-dependent deformation of the standard Burgers material under a three- dimensional state of stress. Time-dependent pillar settlement data at one mine were also analyzed for elastic and viscoelastic parameters of the weak floor strata using the developed equations. These parameters were compared with similar parameters estimated from plate loading tests.

Jan 1, 1990

By R. L. Crosby

From studies of wrought magnesium alloys containing rare-earth elements, data are presented on the mechanical properties of the alloys at room temperature and at temperatures of 100°, 200°, and 300° C. Results of studies of the solid-solubility of cerium and zirconium in magnesium as determined by electrical resistance measurements are also discussed and are compared with those of other investigators. The strength of magnesium-cerium alloys did not increase with the addition of vanadium and titanium dioxide. The addition of zirconium increased the tensile strength of the alloys as much as 10,000 p.s.i. at room temperature, but this increase diminished above 100° C.

Jan 1, 1962