Search Documents

By J. L. Potter

An inert-gas fusion technique was applied by the Bureau of Mines to the oxygen analysis of mixed-fluoride electrolytes used in electrowinning uranium and the rare-earth metals. Method development included: (1) Thermodynamic and experimental evaluation of the temperature required to quantitatively remove oxygen from a fluoride melt; (2) installation of a water and an acid trap to entrain the volatilized fluorides; (3) development of a suitable sample-preparation technique for the heterogeneous fluoride baths in which both pulverizing and pelletizing were necessary to achieve reproducible results; (4) comparison of platinum flux and dry crucible techniques, which showed that the use of platinum was not necessary. The accuracy of the method was evaluated by analyzing fluoride baths containing known amounts of oxygen added as the metal oxide. In the 0.05-to 0.5-percent range, the relative error was about ±5 percent.

Jan 1, 1962

By Edward M. Dowey

The concrete lining for a long 8.05 km (5 mi) section of New York City Water Tunnel No. 3 was cast in place. The contractor, Grow-Perini-Skanska, placed over76,841 m3 (100,505 cy) of concrete, pouring 24 hours per day, 5 days per week. The concrete was dropped 204 m (670 ft) to the tunnel level, transported by rail to a concrete remixer and pump, and placed in 146.3m (480 ft) of full circle forms. Some of the many challenges include the sheer magnitude of the job, navigating through drifts, a raise and curves, dealing with ground water inflows, and placing the concrete within time limits.

Jan 1, 2001

By S. H. Lorain

This paper briefly describes the principal known commercial and near commercial deposits of gold-bearing gravel end the principal placer mining operations of Idaho County, Idaho. It is one of a series of similar papers on western mining districts. The data used in writing this paper were gathered during the summer of 1937. Information concerning gold-bearing gravels was obtained from prospectors and operators, while operators supplied most of the data on mining operations. No attempt was made actually to test the gravels. The principal object of the examination was to indicate placer areas worthy of further investigation by prospective operators.

Jan 1, 1938

By Mario Terceros H., Bengt H. Fellenius

"ABSTRACTFour strain-gage instrumented bored piles were constructed in a sedimentary, dense to very dense, fine to medium sand in Santa Cruz, Bolivia. Two of the test piles were the normally used bored pile constructed with bentonite slurry and two piles were Bauer Full Displacement Pile (FDP). One of each pair was equipped with the Expander Body, an inflatable steel cylinder that on pressure-grouting provides an enlarged pile toe. Head-down static loading test were performed on three of the piles and a bidirectional test was performed on the fourth pile, a standard pile with Expander Body and a bidirectional cell placed immediately above the EB. The latter pile was tested in 3 phases. First by activating the cell, second, by a head-down test, and, third, by a repeat bidirectional cell test. The static loading tests proved the shaft resistance of the FDP pile to be about twice that of the standard bored pile and that the Expander Body more than doubled the toe stiffness. The strain-gage records showed that the standard bored piles had multiple bulges and neckings, which affected the evaluation of the axial stiffness and load distribution of the piles. The testing programme was used for a prediction event with 60 persons, ahead of the tests, submitting predictions of the load-movement curves for the test piles and also a capacity appraised from the curves.1. INTRODUCTIONOn April 23 - 26, 2013, the First International Conference and Seminar on Deep Foundations was held in Santa Cruz, Bolivia under the auspices of INCOTEC SRL, the UAGRM University, and the Bolivian Association of Civil Engineers and Chamber of Construction. To coincide with the conference, a research study on construction and static and dynamic testing of four instrumented bored piles was undertaken. To ""add spice"" to the conference, a prediction event was organized on the test programme. This paper presents the soil conditions at the site, the type and construction of the test piles, the outcome of the prediction event, and the results of the static tests.2. SOIL CONDITIONSGeotechnical studies comprising SPT and CPT tests with routine laboratory analysis were performed on recovered soil samples. Three SPT boreholes were put down at three of the locations of Pile TP1, TP2, and TP3, at 5.0 m distance from each other. The SPT procedure consisted of manual hoisting of the weight by three crew members pulling on ropes over a pulley supported by a tripod and letting the weight fall by gravity. The groundwater table lies at 3.5 m depth.Figure 1 shows diagrams of the SPT N-indices and the distribution of water content in the three boreholes. The SPT-indices show the soil density to be compact. The average water content is about 15 %, plus-minus a few percent."

Jan 1, 2014

By Harald Ludwig

In 2002, excavation support work commenced on the Capitol Visitor Center project located adjacent to the nation?s Capitol building in Washington, D.C. The outlying work (Slurry Wall Work at Main Site is not discussed) consisted of providing excavation support for a new truck tunnel approximately 1900 feet long up to 50 feet deep as well as support for the new underground auditorium and Library of Congress tunnel. The excavation support consisted of a combination of conventional drilled in soldier beams, lagging, tiebacks and braces; intricate underpinning inside the existing Capitol building; support of an existing Russell Tunnel; soil nailing and tiebacks underneath the existing Russell Tunnel; two temporary bridges; and a deep soil mixed wall with lateral support provided by braces. As part of an on-going research program, some of these braces were instrumented with strain gauges. The deep soil mixed wall was approximately 300 feet long and 65 feet deep on either side of the truck tunnel. Approximately 34,000 sf of deep soil mixed wall, 90,000 sf of conventional excavation support, 200 braces, and 320 tiebacks were installed. This paper describes the large scope and breadth of the project that required a variety of excavation support techniques. A few of the challenges in designing and installing the support of excavation are discussed. This paper also presents the results of the instrumentation program conducted on the deep soil mixed wall, which stood open for more than a year.

Jan 1, 2006

By T. Lindstad, J. Kaczorowski

The Boudouard reactivity of single cokes produced from selected bituminous coals and commercial cokes has been investigated in a thermo gravimetric furnace. The effect of potassium as a catalyst for this reaction was studied, as it is known to accumulate in ferromanganese furnaces. A gaseous impregnation technique using K2CO3 as the potassium source was applied to impregnate the coke samples. The reactivity experiments were designed to simulate conditions occurring in an industrial furnace, as used for production of Mn-alloys. The coke particle size varied from 3.35 to 6.63 mm, while the temperature was maintained between 800- 1100oC with a gas composition from 50 to 75% CO2 in a CO/CO2 mixture. To determine the catalytic effect of potassium, the concentration varied from a fraction of a percent up to 15%wt. The results show that single chars vary significantly in reactivity, depending on the properties of the parent coal, while commercial cokes exhibit similar reaction rates. Temperature and partial pressure of CO2 have the strongest influence on the reactivity, while the influence of gas flow rate and coke particle size were found to be negligible. The catalytic studies revealed that the relative reactivity of non-impregnated samples are preserved after the impregnation, so the least reactive coke is still the least reactive after the impregnation for the whole range of potassium loads. Also, it has been confirmed that the Boudouard reactivity reaches a plateau at potassium concentration of 4%wt.

Jan 1, 2007

By C. Pelley, S. Kelebek, S. Gregersen, P. Katsabanis

A series of small scale tests have been conducted to evaluate the effect of micro-fracture development, imposed by blasting, on the physical properties of the rock as well as its resistance to crushing and grinding. The uniaxial compressive strength, tensile strength, Young’s modulus, Poisson’s ratio, P-wave, S-wave velocity, point load strength index and grinding work index were evaluated for samples without any blasting load and for samples which had received a variety of blast loads, such as a simple side impact from a detonating cord, or combined impacts without any delays and with very short delays. The investigation covered two types of rock, granodiorite and limestone. The effect of blasting load on the physical and rock mechanics parameters of the rock was clearly shown and damage was quantified and related to loading. However the work index did not show significant differences between blasted and not blasted samples, probably due to the relatively low level of impact. Numerical modelling using the AutodynTM code was used to demonstrate damage development in the various configurations tested.

Jan 1, 2003

In general, the metallurgical industry has so far been slower than the chemical industry to adopt ion exchange materials for industrial processes. The atomic energy industry presents a marked exception to this general situation, and the literature shows a rapidly increasing use of ion exchange techniques for the recovery of atomic energy metals on scales ranging from the ultra micro up to that of the largest mining operations. In many cases, the processes used would be equally applicable to more common metals and it is hoped that this review will be of interest to metallurgists outside the specialised atomic energy field. The review is intended to describe developments of ion exchange processes made during the last three years. Earlier studies have been summarised by Kunin and Preuss (1956) and Roland (1957). In order to restrict the number of references discussed, purely analytical procedures have been omitted and only those processes which have been conducted on a reasonably large scale or which, from their nature, areclearly capable of being upscaled, have been considered. The paper is divided into five main sections concerning respectively:Water treatment and effluent disposal.Metal recovery and purification.New ion exchange materials.New ion exchange equipment.Membrane cells.WATER TREATMENT AND EFFLUENT DISPOSALA high proportion of atomic reactors, and particularly those of American design, are cooled by water which is...

Jan 1, 1961

By B. M. England, M. V. Swain, N. Bristow, R. D. Dukino

The toughness and fracture mechanisms of ores with significantly different microstructures from Yandi, Koolan and Mount Whaleback were studied with a view to understanding their degradation behaviour. Bulk fracture toughness was determined by the 3-point single-edge notch beam test and the results interpreted using Weibull statistical analysis; indentation fracture mechanics was also used to measure fracture toughness of the different mineral forms and to understand their response to contact fracture

Apr 1, 1995

By Stephen Davies

Mining at Hudson Bay Mining & Smelting's Snow Lake Division is now in the mature stage of the mines' lives. These base metal copper-zinc mines have been operating for more than 30 years. Stopes had small pillars called "crown pillars" left between them. These pillars range up to 100 m (330 ft) long by 40 m (130 ft) wide and 15 m (50 ft) thick. Hudson Bay have been successful in removing these pillars by using cable slings, electric scoops, longhole mining and diesel load-haul-dump equipment. The different shapes and sizes of these pillars has required that many innovative techniques be tried in order to find acceptable economic mining methods. An overview of the different methods will be outlined. Background Hudson Bay Mining & Smelting's Snow Lake Division is located in Manitoba some 800 km (500 miles) north of Winnipeg and 200 km (125 miles) by road from the Hudson Bay smelter complex located in Flin Flon, Manitoba (Fig. I). There are currently three producing underground mines and one open pit operating at the Snow Lake Division, producing copper and zinc concentrates. Pillar recovery is intensive and vital to continued production of these mature mines. The crown pillars are producing more than 50% of the current mine production. This figure will increase in the future. The two mines at which crown pillar recovery is taking place and that will be discussed are the 400 t/d (440 stpd) Rod Mine and the 1000 t/d (1100 stpd) Stall Lake Mine, both five-day-a-week producers. Crown pillar mining has been applied for some time at these mines. However, it was only recently that the crown pillars became vital to production. This has necessitated a number of innovative techniques to recover them.

Jan 1, 1992

The development of information concerning mesothelioma in South Africa started with the 1959 finding of Dr. J. Christopher Wagner of cases of mesothelioma in persons living in the vicinity or working in crocidolite mines in Cape Province. After more than 40 years, the data from South Africa now provide important insights into the differences in mesothelioma risk associated with different asbestos fiber-types. Three case series reports and one analytical report were reviewed in this session. In total, information on 504 proven cases was presented. There were 28% of cases arising from occupational exposure in mining, 35% from non-mining occupations, 23% from environmental exposures; 14% where no exposure was established and 9% where the exposure was unknown. Among the 129 cases for which occupational exposure and asbestos fiber-type were established, 115 cases were associated with occupational exposure to Cape crocidolite; 1 case associated with occupational exposure to Transvaal crocidolite and 9 cases with occupational exposure to amosite (grunerite asbestos) and 4 cases with occupational exposure to mixed fiber-types. There were no cases associated with chrysotile asbestos. There were 33 cases of environmental mesothelioma linked to Cape crocidolite exposure and 2 to exposure to amosite and crocidolite but none to Transvaal amosite alone or to chrysotile. The evidence shows that amosite is capable of causing mesothelioma but that the major risk in South Africa is associated with Cape crocidolite.

Jan 1, 2008

By Brown A

An experimental evaluation of a selective agglomeration process in which an agglomerated coal rich phase was produced as a result of mixing light oil to various raw coal slurries is described. The beneficiation achieved by this method is compared to that obtained bv conventional froth flotation. The results suggest' that oil agglomeration is a more selective process than froth flotation and is less sensitive to variations in feed pulp density. Selective agglomeration has the additional advantage of producing a low moisture content product. The effect of replacing flotation filter cake with an equivalent amount of selectively agglomerated product in coke-making was studied with the aid of a pilot-scale coke oven. The results suggest that the principal effect of such a measure is to increase the bulk density of the charge.

Jan 1, 1977

By James A. Finch, Stéphanie Gélinas

"A colorimetric technique, originally developed for methyl iso butyl carbinol (MIBC) based on the Komarowsky reaction, has been extended to a wide range of common mineral flotation frothers. The procedure, which is briefly described, is shown suited to on-site determination in a series of industrial campaigns. Some frother observations are described, including: concentration evolution down a bank, distribution between pulp and froth phases, and a mass balance around a circuit. Minute amounts of frother in recycle water were also measured.The contribution of frother and alcohol by-products in the analysis was generally additive for plants using aliphatic alcohol type frothers and decoupled for systems using glycols. Typically, U250C (polyglycol) was used at higher concentration (>10 ppm) than MIBC (aliphatic alcohol) (<10 ppm) or F-150 (polyglycol) (<3ppm).The ability to monitor frother easily will help interpret gas dispersion behaviour and should permit further optimization of flotation cell hydrodynamics and chemistry. The capability to directly measure should help optimize the type, amount and location of frother addition, and to assess frother recycled with reclaim process water.INTRODUCTIONOwing to the lack of analytical methods, the task of determining frother concentration in plant flotation circuits is not routinely performed. Industrial sites seldom outsource analyses that are both costly and inconvenient, due to the necessity of shipping freeze-dried samples to remote testing facilities. A more direct colorimetric method has recently been demonstrated for the laboratory characterization of common industrial frothers (Gélinas and Finch, 2004). The approach, based on the Komarowsky reaction (Penniman et al., 1936; Coles et al., 1942; Duke, 1947), was previously described by Parkhomovski et al. (1976) for methyl iso butyl carbinol (MIBC). The reaction involves the interaction of the OH group of a higher alcohol, concentrated sulphuric acid, and salicylaldehyde, to yield coloured solutions with intensities that can be analyzed by UV-visible spectrophotometry."

Jan 1, 2007

By Seung-hoon Lee

The use of piled raft foundations has been considered as an economical alternative to conventional piled foundations because a portion of the applied load is carried by the raft in the design of piled raft foundation. In analyzing the behavior of a piled raft foundation as a settlement reducer, an accurate estimate of settlements of the system should be made on the basis of the understanding of nonlinear behavior of piles in layered soils as well as the interaction between the raft, soils, and piles. Although the 3-dimensional finite element method and simplified analysis methods have been used for the design of piled raft foundations, these methods were found to be inadequate for the practical purpose or could not consider the interactions properly. This study developed an approximate hybrid method of analysis to be used for the practical design of piled raft foundations considering pile-soil, raft-soil, pile-soil-pile and raft-soil-pile interactions. In the presented method of analysis, the settlements of the system are estimated satisfying the compatibility of two separate models which are the flexible raft model consisting of 2-dimensional finite elements supported by springs representing soils and piles, and the group-pile model embedded in layers of soil having different properties. Comparisons with other analytical methods as well as a 3-dimensional FEM program were made to verify the sufficient capabilities of the proposed hybrid model for application to practical design and analysis of piled raft foundations.

Jan 1, 2008

By Paul R. Thomas

The Bureau of Mines evaluated the impact of the depletion allowance upon the economic availability of copper from domestic deposits. The potential long-run percentage depletion deduction, cumulated over the life of the properties, was estimated at approximately $2.5 billion for producing properties and up to $11.7 billion for nonproducers. The income transfer, in the form of higher Federal income tax payments if the allowance were repealed, was estimated at $1.5 billion for producing properties and up to $8 billion for nonproducers. The percentage depletion allowance, through its role in determining Federal income tax liability, was found to be very significant in affecting profitability. Repeal of the allowance could result in major domestic copper availability reductions at all price levels, now and in the future, as a result of reduced profit margins for current producers, and postponement of development decisions for nonproducers. It was demonstrated that a 50-percent reduction in the percentage depletion rate applicable to copper would also result in a significant decrease in profitability for nonproducing properties. For producing properties, the percentage depletion rate on copper was shown to be less significant than the income limitation that is placed upon the total amount of the depletion deduction. Repeal of the minimum Federal tax provision was shown to be significant in enhancing profitability for both producing and nonproducing deposits. The report concludes that the percentage depletion allowance operates as an important method of capital recovery and production incentive.

Jan 1, 1982

By L. C. Bird, N. T. L. Landgren, M. W. Mikhail

"Through funds made available in 1972 by the Nova Scotia Department of Mines and Energy (DME) and the federal Department of Regional Economic Expansion, a program was initiated to recover saleable coal from mine waste dumps adjacent to the existing Acadia wash plant in Stellarton, Nova Scotia.Following evaluation of these dumps in 1972, the Acadia wash plant was modified to treat high-ash material. The first production was recorded in late 1974. By the end of 1979, a total of 738,202 t of dump material had been processed, yielding a total of 205,212 t of thermal-quality coal.The successful Stellarton operation led to considering the possibility of recovering thermal coal from other dumps. Evaluation of the Westville dumps indicated total recoverable reserves of 1,346,617 t averaging 53.8OJo ash.Parameters for plant design were defined from the washability characteristics of the dump material and the results of a bulk test. Two options were proposed; one was to use the existing plant with some modifications, the other was to build a modular mobile plant that could be used at future dump sites in the province after Westville. At the 25% ash level, the potential recovery of coal from the dump was estimated at 41% yield (by weight) or 549,679 t."

Jan 1, 1981

By Ronald E. Heuer, Debra L. Virgens

INTRODUCTION Behavior of clay soils in response to tunneling is reasonably well understood by reference to the tunnel stability factor NT = Pz/su (Peck, 1969; Heuer, 1974). With this analysis tool, care must be taken to use a value of clay shear strength which represents the actual mass strength, considering such factors as slickensided fissures often found in stiff and hard clays. Behavior of clean sand and gravel soils is also reasonably well understood. Above the water table these soils must be assumed to act as running ground unless they are known to have significant cementation or have a very dense and angular interlocked grain structure. Below the water table they must be tunneled using some form of groundwater control such as dewatering, grouting, freezing, or internal fluid pressure in the tunnel such as compressed air or a slurry tunneling machine. The internal fluid pressure must approximately balance the external water head. Without such precautions these soils behave as flowing ground and may yield large volumes of water flow into the tunnel. A wide range of very fine sand, silty sand, cohesionless silt, and clayey sand soils exist in nature in a variety of geologic environments. The behavior of these soils in response to tunneling, and guidelines for anticipating their behavior, are not well described in the literature. Because of their content of fine particles, these materials may behave as if they initially have appreciable cohesion and moderate to low permeability. They may exhibit significant standup time, and require tunnel internal fluid pressure (compressed air or slurry pressure) less than the full external water head. It is important to be able to estimate the behavior of these soils when planning construction methods. For example, if the external water pressure is 140 kPa (20 psi), but soil stability at the tunnel face can be achieved as a compressed air pressure of 80 kPa (12 psi), a large cost savings may result.

Jan 1, 1987

By A. Adu-Acheampong

A geotechnical study was conducted to identify the cause(s) of stope instability at the Ashanti Mine (Obuasi, Ghana). As part of the investigation, laboratory testing of rock was performed and the rock mass was classified according to the Q-System (Barton et al., 1974).Numerical analyses were performed using the computer program FLAC (Itasca, 2001). The observed failure zone around the stopes was simulated using both Mohr-Coulomb and Hoek-Brown (Sheorey,1997) models. Yielding along peripheral graphite bands and tensile failure were clearly identified to be the major contributors to stope instability.

Jan 1, 2003

The iron ore deposits of the Port Hedland district of North Western Australia are associated with band&apos;ed sedimentary iron formations that form part of the local succession of folded and faulted Archaean volcanic and sedimentary rocks. The iron formations are regarded as the protore beds or sources of the iron which became concentrated by supergene processes to form commercial grade iron ore deposits.Iron oxide deposits occurring in situ within the protore beds are considered to be of residual-replacement origin, due to supergene leaching of gangue minerals and&apos; deposition of secondary iron oxides in their place, Two types of deposit have been recognized. Lode deposits are deep lenses of massive hematite located adjacent to major faults. These deposits are thought to be very old and to have originated by supergene processes during the long period of erosion represented by the major unconformity between the Archaean rocks and the overlying Proterozoic beds. The other type, known as crust ore deposits, are shallow cappings of hematite and goethite on hills formed by the outcrops of steeply dipping protore beds. These deposits could have originated as far back as the early Mesozoic and it is possible that the ore-forming process is continuing at a slow rate at the present day.Deposits formed by erosion and re-deposition of material derived from pre-existing residual-type deposits are known as derived deposits. These include conglomerates and scree accumulations of various types and ages and pisolitic deposits formed by supergene leaching of transported detritus. Derived deposits range in age from early Proterozoic to Recent. The presence of pebble accumulatio,ns of lode-type hematite in the Proterozoic basal conglomerate provides good evidence that lode hematite deposits existed in pre-Proterozoic times.INTRODUCTIONThe existence of iron ore deposits in the Port Hedland district of Western Australia has been known since the beginning of the century, but little attention was paid to them untIl the 1930&apos;s, when the Commonwealth Aerial, Geological and Geophysical Survey of Northern Australia carried out investigations of most of the then known mining fields of the Northwest Division. The only iron...

Jan 1, 1964

[This is the sixth in a series of reports on properties of commercial motor fuels, made in accordance with a cooperative Agreement between the Cooperative Fuel Research (C.F.R.) Committee and the Bureau of tines of the Department of the Interior. The first report gave data on motor gasolines sold during the winter of 1935.-36.3/ The present report cover brands of gasoline represented by 1,490 samples plus thus: from the Pacific Coat, which ;sere averaged by the Pacific Coast Technical Group before being submitted and are published exactly as they were submitted. In some areas reports were received from 8 to 10 companies on the same brands of gasoline, Whereas in other areas only one Company reported on a brand. Thus, it can be seen that soma of the data are more representative than others. The inclusion of data from several cities within some of the districts has improved the report by reducing the number of brands reported by only one company. Severe changes have been made in the districts. A new district, Memphis, Tenn., has been formed to include Arkansas any western Tennessee. The Rocky Mountain area, have been divided into three sections. Salt Lake City and Denver form the Middle Rocky Mountain district; Laramie, Wyo., Idaho, Montana, and. Spokane, Wash., are included in the North Rocky Mountain district, and Arizona, New Mexico , and El Paso, Tex., have been combined to represent the South Rock Mountain district. The Cleveland district has been expanded to include Ohio ant. Indiana. Eastern Pennsylvania, Maryland, and northern Virginia are included in the Washington (D. C.) district. The Atlanta district includes Georgia, South Carolina; Mississippee, and northern Florida.]

Jan 1, 1938