Search Documents

By A. W. Khair

Laboratory studies indicate that the specimen size influences the compressive strength of coal significantly. In the past, the diameter/height ratio of coal and rock specimens with different geometry and its influence on failure characteristics was discussed (Khair, 1993; Khair, 1994; Khair and Xu, 1994). In the current attempt, tests are designed and carried out under uniaxial condition in the laboratory to investigate the influence of specimen size. Cubical specimens of coal with edge dimension ranging from 5 cm (2 in.) through 20 cm (8 in.) were prepared according to the standards and tested uniaxially. Results show that compressive strength of coal is dependent on specimen size until certain level and later the change in specimen size would not yield significant change in compressive strength. Cubical specimens were chosen for testing because they are not only in close resemblance to underground pillars, but they are also the most stable shape under loading. The failure characteristics of these specimens were analyzed and their applicability to pillar design aspects in coal mines is studied. A detailed analysis of the physical and mechanical properties of the tested coal seam is also presented.

Jan 1, 1996

By James J. Scott

Research and development has been carried out on the patented Dynamic Rock Anchor, tradenamed DYNA-ROK and DYNA-ROK PLUS Anchors, which are manufactured and marketed by Ingersoll-Rand Company. This paper will present the results of field testing of this revolutionary new concept in ground control. Geologic conditions will be described where the plastic sleeve of the DYWA-ROK anchor alone is sufficient to provide anchorage and also, where in softer ground conditions, the DYWA-ROK PLUS is applied. The rationale for making the decision as to the type of fixture to be employed, the length of plastic tube to be used and the quantity of resin are explained. Pull test data will be shown from eight different coal seams in the Eastern United States where the product has been installed.

Jan 1, 1990

Drill cores from Section 62, New Broken Hill Consolidated Ltd., were used to study the petrology of rocks associated with the zinc lode. The distribution of the rock types in relation to the lode structure was determined. The distribution of the gahnite-bearing rocks was shown to be only partly conformable with the structure.It was concluded that large scale metasomatism was not widespread, that the rocks associated with the lode (except, perhaps, the quartz-gahnite-garnet rocks) were formed by metamorphism of sediments, and that rocks and lode were contemporaneously metamorphosed.INTRODUCTIONThis investigation was undertaken in order to study the rock types associated with the zinc lode of the Broken Hill orebody, and their relationship to the structure of the ore horizons. The work was confined almost entirely to the laboratory, and is therefore limited in its scope. It is hoped, however, that the information gained may throw some new light on the genesis of the lode.Certain inferences which are drawn from this work are at variance with the ideas of a number of earlier workers.In particular, the idea of large scale metasomatism developing many of the rocks associated with the lode, especially those containing manganese, is questioned. On the contrary, the rocks associated with the lode are more simply explained as highly metamorphosed sediments, in some cases modified by water introduced from surrounding rocks into zones of strong folding and faulting. As a corollary, a metamorphicsedimentary origin for the lode material, either as a concentrated sulphide deposit, or somewhat disseminated...

Jan 1, 1961

The Pilbara Block is a nucleus of Archaean rocks which lies in the North West Land Division of Western Australia, and it constitutes a mineral province that has been divided into two areas-the West Pilbara Goldfield and the Pilbara Goldfield.In the West Pilbara Goldfield two contemporaneous environments are represented by laterally equivalent volcanic and sedimentary successions which together comprise the Roebourne Group. The two successions are lithologically similar to the classical Warrawoona (volcanic) and Mosquito Creek (sedimentary) successions of the Pilbara Goldfield; but in the West Pilbara Goldfield there is no sign of the erosional break which separates the Warrawoona Succession from the Mosquito Creek succession. The Roebourne Group and the igneous rocks which have intruded it belong to the Archaean Pilbara System.Evidence of preconsolidation movement and igneous intrusion into unconsolidated sediment suggests that tectonism and igneous activity, localized along lines of fracture in an unidentified basement, beganbefore lithification was complete. Movement was primarily vertical, and persisted into the Lower Proterozoic.Vulcanicity and chemical sedimentation, accompanied by a diminution of detr:tal sedimentation, is thought to have caused a relative enrichment in the metal content of the middle part of the Roebourne Group; and the metal may have been remobilized during diagenesis and metamorphism, and localized in zones of dislocation formed both before and after consolidation of the sediments.INTRODUCTIONThe name "Pilbara" has been widely applied in the area under discussion, and to avoid confusion the various uses are summarized below.1. The town of Pilbara, now abandoned, was a centre of mining between 1888 and about 1914. It lies some 90 miles FJSK of Roebourne (Fig. 1).2. The original Pilbara Goldfield was modified several...

Jan 1, 1965

By C. M. Harrer

This paper describes the location and general features of iron occurrences in Colorado. Most of the deposits were examined; many are in forested and mountainous areas at altitudes of 5,000 to 13,700 feet. Iron is known to occur in 30 counties of western Colorado. Transporting the ore to market is a handicapping economic factor involving long truck and railroad hauls; the nearest purchaser of smelting ores is the Colorado Fuel and Iron Corp., at Pueblo, Colo. When the ore can be sold locally for special purposes and at higher prices than can be obtained at iron smelters, small-scale operations can supply that market.

Jan 1, 1959

By Raymond Rivera

El presente texto describe la evaluación desarrollada por INGEMMET donde se analiza el potencial de los depósitos minerales en el Batolito Andahuaylas, Yauri, así como el potencial de algunas zonas que presenten características geoeconómicas importantes, utilizando herramientas geológicas como geocronología, isótopos radiogénicos, geoquímica de rocas y sedimentos, petromineralogía y geología estructural.

Sep 12, 2011

By J Law, S Jahanshahi, R Holmes

Iron ore is AustraliaÆs largest commodity export and is vitally important to AustraliaÆs current and future prosperity. However, while major expansions are currently in progress to satisfy demand, the industry is also undergoing major transformations. Reserves of traditional high-grade Brockman ores that have underpinned the Australian iron ore industry since its inception are slowly being depleted and alternative ore types such as Marra Mamba bedded iron deposits, Yandi and Pannawonica channel iron deposits and magnetite deposits are now being developed. However, the impurity levels in some of these alternative ores are higher and they require blending and/or upgrading as well as an advanced knowledge of their downstream processing characteristics to facilitate cost-effective utilisation by overseas customers. The research challenge is to use advanced techniques for mineral exploration, ore characterisation, mineral beneficiation, agglomeration and sustainable processing to identify and develop innovative and breakthrough options for locating, unlocking and enhancing the value of AustraliaÆs iron ore resources. Furthermore, to sustain the steel industry and hence secure the demand for iron ore, there is a growing need to enhance the environmental and business performance of the industry through reductions in wastes and emissions. Therefore, cost-effective breakthrough and enabling technologies that massively cut waste generation, CO2 emissions and water consumption are also being developed. These include the use of renewable fuels and reductants, waste heat recovery and conversion of by-product slag into a saleable substitute for Portland cement. A number of examples of recent developments in the above areas are provided in this paper.CITATION:Holmes, R, Jahanshahi, S and Law, J, 2013. Research and innovation for the iron ore to carbon steel value chain, in Proceedings Iron Ore 2013 , pp 3-6 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By McLeod RL

The Tolukuma gold-silver prospect is located approximately 100km N of Port Moresby in the Central Province of Papua New Guinea (PNG). Epithermal "adularia-sericite" style mineralisation crops out over 1200m within an en echelon quartz veined zone 1 to lOm wide. At a 4g/t cut-off grade, a geological resource of approximately 1.47Mt @ 13.77g/t Au is indicated from 38 diamond drill holes completed since discovery by Newmont Pty Ltd in September 1986. At a regional scale, Tolukuma miner- alisation appears localised in a dilatant zone at the intersection of a 1150 magnetic structure, and the western margin of a N-S trending graben which is filled by a Pliocene volcanic complex contemporaneous with the Mt Davidson Volcanics 30km to the W. A l0km diameter circular Landsat feature, which may reflect magma emplacement at depth, occurs immediately N of Tolukuma and nearby mineralisation. Mineralisation at Tolukuma occurs in sub-vertical quartz veins at, or adjacent to the faulted contact between Pliocene basic and intermediate volcanics/intrusives, and quartz mica schists and phyllites of the Cretaceous Kagi Metamorphics. Most veins display evidence of multiple episodes of brecciation and textures indicative of cyclic boiling, including crustiform rhythmic banding and quartz pseudomorphs after platy calcite.

Jan 1, 1991

By D. Craig Camp

conditions. The soils included 65 m of rock not exceeding an unconfined compressive strength (UCS) of 200 kgf/cm2, 130 meters of soft clay, silt, and sand not exceeding 30standard penetration test SPT blows per 300 mm, and 220 m of rock ranging between an UCS of 400-600 kgf/cm2. The river crossing, utilizing 1778 mm OD x 19 mm wall x600 mm steel casing pipe without intermediate jacking stations, was part of a seven kilometer liquefied natural gas (LNG) transmission line in South Korea. This 440-m, 1,442-ft, river crossing was microtunneled through three different ground conditions and completed in just over three months. The crossing was achieved with an average of 25 m of ground cover and 15 m of water cover. The Kwang Yang River Crossing was part of a 7 km liquefied natural gas pipeline project for POSCO, a Korean steel producer. The microtunneling machine was custom built for this project. The microtunneling machine selected for this project was tooled with 7 button bits and 2 roller bits. None of the cutter bits were replaced during the drive. Inside the machine, before the spoils laden slurry was pump back to the surface, it would pass through an independent cone crusher. The crusher is placed in the slurry flow to make sure that none of the spoils are so large as to stop the return flow of the slurry. An additional requirement was for the inclusion of a compressed air lock. The air lock was required in the event that the cutter tools required replacement. The cutters were back loaded so that the workers would have access to change the cutters in the event of cutter failure or wear out. No intermediate jacking stations were installed for the drive. The soils included 65 meters of rock not exceeding an unconfined compressive strength (UCS) of 200 kgf/cm2 with production averaging between 7 and 20 mm/minute. The second zone contained 130 meters of soft clay, silt, and sand not exceeding 30 standard penetration test (SPT) blows per 300 mm with production averaging between 80 and 180 mm/minute. The third zone contained 220 m of rock ranging between an UCS of 400-600 kgf/cm2 with production averaging between 7 and20 mm/minute. The steel casing pipe was 1778 mm OD x 19 mm wall x 6000 mm long. The project profile, see Figure 1, shows the soil conditions. The hand written numbers locate just above the pipeline are the production dates. The circled numbers are the 10 pipe joint increments. The project required 74 pieces of pipe to span the440 m drive. Figure 2 and Figure 3 are the jacking information. Figure 3 is a continuation of the information from Figure 2. The top section of the graph is the jacking force. The jacking

Jan 1, 2001

By Joe Roby

Rolling disc cutters are the business end of hard-rock and mixed-face tunnel boring machines (TBMs). Since their first successful employment on a TBM more than 50 years ago, disc cutter technology has constantly evolved, allowing modern TBMs to excavate very hard and abrasive rock efficiently. Disc cutters have also been employed successfully on earth pressure balance (EPB) and slurry machines, cutting rock under water and ground pressure. The range of materials excavated by machines today is broader, excavation rates are higher and cutter costs are lower than ever before, proving the value of investment in cutter development. Disc cutters are used on a range of tunneling equipment, from pipe jacked slurry micro-TBMs less than 1 m (3.3 ft) in diameter to 15 m (49 ft) in diameter, hard-rock boring TBMs. The geological conditions under which they are employed range from sands and gravels, with several bar of water pressure, to extremely hard, massive rock with UCS up to 420 MPa. Regardless of the type of machine or geology, one thing remains constant: changing worn out cutters is costly. When cutters must be changed in the middle of a tunnel, the contractor incurs the cost of downtime as well as the cost of refurbishing or replacing the cutters. In the case of catastrophic cutter failures, the project can be stopped completely for long periods, and the costs mount up rapidly while tunnel production is at a stand still. Catastrophic cutter failures include the occasion when hard-rock disc cutters are failed in groups (called a ?wipeout? phenomenon) and the operator fails to stop the machine, which results in severe damage to the cutterhead. The cause of this can be either an undetected failed cutter propagating damage to surrounding cutters or operator error in steering. Regardless of the cause, the resulting damage can take days or even weeks to repair. When cutters fail prematurely on EPB or slurry machines in certain geological conditions, it is impossible to evacuate the chamber and, therefore, impossible to get [ ] into the chamber to change the cutters. The solution is frequently an unplanned intervention shaft that must be sunk at great cost. The importance of being able to predict cutter life accurately, and in all geological conditions, cannot be overemphasized. For these reasons, cutters have been developed for specific machine types and sizes, as well as for specific geological operating conditions. Different size cutters are required for different size machines. For example, while 483- and 508-mm (19- and 20-in.) cutters are used on large diameter TBMs, it is impossible to employ cutters so large on a small micro-TBM. Also, the cutter must be designed for the specific geological conditions under which it will be operating. The disc cutter rings required to bore extremely hard rock are the most expensive of cutter rings. However, they provide little advantage in weaker rock formations where less expensive rings will do the job as well. It is important to choose the correct cutter for the machine and the geological conditions in order to get the best balance of cost and risk.

Jan 1, 2009

By T. H. Eyde

Estimated natural zeolite production worldwide during 2004 remained at about 3.6 Mt (4 million st), about the same as in 2003. China continues to be the largest producer of natural zeolites followed by Cuba, Germany, Japan and South Korea. This may be changing, however. Since 1988, zeolite production from Australia, Indonesia, Malaysia, New Zealand, Philippines and Thailand has increased rapidly. Most of the production is consumed in aqua culture. Global demand for seafood has exceeded the ability of the oceans to supply it without over fishing. Zeolite minerals remove ammonia compounds from the ponds in which fish and shrimp are grown. It is estimated that, in Thailand and Indonesia more than 55,000 farms produce260 kt (286,500 st) of shrimp. Therefore, as shrimp production increases, so does zeolite consumption.

Jan 1, 2005

By P. L. Crouse, S. J. Lubbe, M. J. Kabangu

A selective extraction and separation of zirconium by solvent extraction with 1-octanol is proposed. The process is based on the dissolution of the metal basic carbonates in hydrochloric acid in the presence of potassium fluoride, using 1-octanol as extractant. The effect of several process parameters, including hydrochloric acid and potassium fluoride concentrations, reaction time, and phase ratio between the aqueous and the organic phase was investigated. Zirconium is enriched in the organic phase. The best extraction and separation results were obtained with the basic carbonate dissolved in 10% hydrochloric acid and 1.5 M potassium fluoride. The optimum reaction time was 15 min with an organic to aqueous phase ratio of 2:1. Based on the selectivity of zirconium over hafnium in the organic phase, a McCabe-Thiele diagram was constructed. A near complete stripping of zirconium from the organic phase was achieved using a 3 M sulphuric acid solution. Additional studies are required in order to determine the reaction mechanism and the chemical speciation of the current investigation.

By P. J. Mehrfert

"Recovery of mineralized coarse particles is notoriously low in conventional concentrators that treat copper porphyry ores. The application of coarse particle flotation techniques has the potential to achieve comparable metallurgical performance at significantly coarser primary grind sizings. ALS Metallurgy has been conducting both internal research and commercial test programs to investigate the potential of Eriez HydroFloatTM technology on copper sulphide ores. Test data indicates that significant improvements in the recovery of copper sulphide bearing particles between 200µm to 850µm can be achieved using Hydrofloat technology compared to conventional flotation techniques. This paper summarizes the results from a selection of test programs that includes recovery by size data from both conventional flotation and HydroFloatTM tests. An explanation of the apparatus and test procedure will be given. Mineralogical analyses of the test products and characteristics that limit metallurgical performance will be discussed.Description of Apparatus and Test ProtocolThe HydroFloatTM laboratory cell is a clear plastic column with an internal diameter of 14 cm. Water and air are introduced to the cell through a circular manifold located in the lower portion of the cell. The cell has a conical bottom which directs slurry to a pinch valve that controls the discharge of tailings. Feed solids are introduced to the upper portion of the cell in slurry form. The cell is operated in a manner such that the manifold water creates a teeter bed zone of suspended solids in the middle portion of the cell. Tailings exit the bottom of the cell at a high pulp density, and most of the introduced water overflows the top of the column and is collected in a launder. Particles with a hydrophobic surface may attach to air bubbles that percolate through the teeter bed, rendering them sufficiently buoyant to be transported to the overflow launder.Three significant features of this arrangement enhance the potential to recover coarse, low grade particles by flotation techniques. Firstly, the hindered settling conditions created by the rising column of water allow coarse particles to become buoyant once attached to a modest sized air bubble. Secondly, the flow conditions within the cell are relatively quiescent compared to a conventional flotation cell that utilizes an agitator. This allows particles that have limited hydrophobic portions of their surface, due to a low content of exposed sulphide mineral, to maintain a somewhat fragile attachment to air bubbles long enough for successful recovery to the overflow. Finally, the absence of a froth phase at the top of the cell allows particles attached to air bubbles to immediately exit the vessel, reducing the potential to drop back into the pulp phase as bubbles burst or coalesce."

Jan 1, 2017

By I. S. Blair

The introduction of the 36 MVA smelting furnace at Mufulira, and the experience gained during the first five years of operation have been described previously (6). Based on this experience the furnace was rebuilt in 1977., Details of the modifications made during this rebuild are described. Subsequent to the rebuild, refractory failures, particularly in the electrode ring bricks of the sprung arch roof, continued to cause concern, and repair and improved roof control methods are described. Electrode breakages continued, but developments in casing design and electrode preparation have resulted in significant improvements. Modifications in the electric furnace gas handling system are outlined, together with details of further changes to be implemented in the near future. The systems developed for metallurgical control of the furnace and the thermo-dynamics of the process are discussed. The electric furnace at Mufulira is now operating at above design production levels, and has decisively justified the choice of this technology in situations with inexpensive electric power. The potential for further increases in production capacity from the Mufulira unit, and improvements in design for new units are discussed.

Jan 1, 1983

IN the recent monograph on Broken Hill, N.S.W., by E. C. Andrews,* two independent petrological reports appear as Appendices 1 and n, by W. R. Browne and F. L. Stillwell respectively. In these considerable differences of opinion occur. Andrews contributes to some of the questions at issue, but no analytical review of the differences appears in the body of the report. Their development may invite question, and the following notes have been prepared partly in explanation and partly as a summary of some of the divergences. The soope of Browne's report extends over the whole district of Broken Hill, while Stillwell's deals with the rocks within 25 chains of the main lode. The more difficult and important rock-types occur in both areas, raising similar questions. In both cases observations extended beyond the limits of the prescribed areas. Broadly, Browne faces his problem as a study of a series of primary igneous rooks, acid and basio, whioh are intrusive into a series of sillimanite gneisses. The development of the sillimanite gneisses is regarded as belonging to an earlier period than the intrusion of the igneous rooks, while the gneissio structures of the latter are features which are incidental to their orystallization, and are not acquired subsequent to their consolidation. He finally produoes a picture in which his views of igneous injection and differentiation takes a prominent place. One direct result is the claim that three separate periods of metamorphism have oocurred in the Broken Hill area. Stillwell primarily examines the rooks as schists and gneisses since their present dominating features have been acquired during metamorphism. The effort is made to understand suoh differences as might arise from differing conditions of metamorphism upon rocks of similar and different oonstitution. The aim is to divest the rocks of those oharaoters which are due to metamorphism before approaching the questions of intrusive relatio'nships between igneous rocks andsediments.

Jan 1, 1924

By Frederick W. Slack

This paper will discuss the inherent value engineering associated with the design and construction of approximately 184,000 SF of anchored tieback wall, installed as part of the widening and drainage improvements for KY9 in Campbell County, Kentucky. The total project is 2.2 miles in length. The anchored walls, excavation grading and drainage total to a complete project cost of $28.4 million. This is one of the largest design-build projects undertaken by the Commonwealth of Kentucky. It also features another first for the Transportation Cabinet - the general contractor is responsible for quality control/quality assurance. The project is located just south of Cincinnati, OH and is situated along the east bank of the Licking River. The slopes along this stretch of the river have had a long history of movement and instability. The Kentucky Transportation Cabinet advertised the anchored wall portion of this project to be designed and constructed by pre-approved specialty contractors. The Transportation Cabinet provided the basic design parameters to each specialty contractor. Aspects to be discussed include the site and project history, previous attempts at slope stabilization along existing KY9, the technical proposal and bidding process, and the actual design and construction.

Jan 1, 2003

By Z. T. Mathe, M. A. Vera, M. C. Harris

This contribution presents a methodology how to quantify froth zone recovery in a continuously operated laboratory mechanical flotation cell. The methodology consists of relating the overall flotation rate constant to the froth depth of the flotation cell. As a result, a froth zone recovery factor (Rf) can be extracted. This froth performance parameter has been studied as a function of the flotation cell operating variables. By understanding the effect of these operating variables on Rf, an integrated methodology for modelling froth zone performance in batch and continuously operated laboratory flotation cells has been proposed. The Rf modelling is based on a semi-empirical approach which considers a number of parameters to be used. Some of these parameters may have physical significance, i. e. they may be easily and physically measured. The modelling approach consists of taking into account the interaction between the pulp and froth zones. This interaction allows froth zone recovery (Rf) to be predicted. The whole modelling exercise process lies on auxiliaries relationships which indicate the dependence of the parameters with the operating conditions of the flotation cell. This contribution is part of a larger project that deals with the modelling and optimisation of flotation plants (Project P9L, 2000).

Jan 1, 2001

By K. Pirapakaran

The Geotechnical Engineering research group at James Cook University has been working closely with all the leading mines in Australia in the area of minefills. They have carried out substantial research and consulting work on the drainage and stress developments within hydraulic fills. The objective of this paper is to summarize their work during the past five years on hydraulic fills. The paper will serve as a one-stop reference, pointing to relevant literature including the authors? own publications, on various issues covering drainage and stress developments within hydraulic fills. More than 15 different hydraulic fills, representing five major mines in Australia, were studied. Their grain size distributions and placement characteristics including permeability, porosity and dry density were studied and comparisons were made with the limited in situ data available in the literature. Stress development within hydraulic fills has been studied to minimize the risk associated with barricades failure. FLAC and FLAC3D were used to model stress developments within the hydraulic fills and were compared against the approximate closed form solutions available in the literature. A laboratory model was developed to study arching effects within the hydraulic fills.

May 1, 2007

By J Parr, P Ashworth, S Johns, C Yeats, A Littleboy

The ocean floor is increasingly being discussed in terms of its resource potential. New discoveries, improved knowledge and access to unexplored areas of the deep sea and continental shelf are some factors contributing to a renewed interest in the seafloor exploration and mining industry. The industry has been referred to as the ænext minerals frontierÆ. To date, much of the research has focused on proving economic and technical viability of the industry, with environmental issues addressed locally. However, there is limited research internationally, and none known in Australia that considers the social viability of the industry, addressing issues such as regulatory contexts, international precedence and public acceptability. Does the nascent seafloor exploration and mining industry have a social license to operate? Does it have support amongst the wider community? If not, why not? The Wealth from Oceans National Research Flagship explored these questions by scoping the social issues that would surround an expansion. Two desktop studies provide insight into the current level of activity in seafloor exploration and mining, recent developments and the regulatory regimes on which the industry is based. One study focused on the situation in Australia, while the other was internationally focused. A series of workshops were held with key stakeholders from government agencies, industry and other interested parties, such as environmental groups and the fisheries industry. These workshops identified and explored the different stakeholdersÆ perceptions of the benefits, concerns, opportunities and key questions associated with an expansion of the seafloor mining industry. The desktop studies revealed that Australia is one of only a few countries with legislation specific to seafloor exploration and mining. Nevertheless, barriers to licence approval exist because of lack of precedent in applying this legislation. Consequently, the decision process can be vulnerable to political issues and subjective judgements. The outcomes from the stakeholder workshops suggest this inconsistency may be influenced by the high levels of concern and uncertainty over environmental impacts. Uncertainty over environmental impacts can influence the acceptability of an environmental impact assessment (EIA) and also mean the perception of risk is variable. Overall, this research suggests that the future of the seafloor exploration and mining industry will be highly dependent on AustraliaÆs ability to:improve the knowledge-base underpinning the regulatory regime,generate open and transparent communications between stakeholders, andimprove the understanding of policy and regulatory processes.

Jan 1, 2008

By S Worden, A Lee Zhi Yi, E Sellers, G Corder, A Littleboy

The global shift towards decarbonisation is driving competition for the extraction of critical minerals such as nickel, lithium, and copper. To meet this demand, new mines are being developed while mines approaching closure are being reimagined as sites of potential resources. This reimagining challenges how mine closure is being conceptualised. In the conventional case, when a mine reaches the end of its economic life, it is closed or put into care and maintenance until it transitions to the next land use, such as agriculture, native ecosystem corridors, solar farms or integrated eco – precincts (Murphy et al, 2019; Holcombe, 2020) (the authors acknowledge that unplanned mine closures have left a devastating legacy of contamination, safety and cultural heritage impacts). Extracting minerals from closed or closing mines will extend mine life and, therefore, delay relinquishment and transition. In this context, innovative technologies are needed to make mining economically viable. In the first year of her doctoral research on improving stakeholder engagement in mine transitions, Lee Zhi Yi has coined the term ‘mine life extension technologies’ (MLETs) to describe a class of technological solutions that optimise extraction of resources after a mine reaches the end of its economic life. Examples of MLETs include agromining (van der Ent et al, 2015), in situ recovery (Robinson and Kuhar, 2018), and reprocessing or reuse of tailings (Gou, Zhou and Then, 2019). MLET extraction offers several benefits compared with conventional mining processes, such as waste remediation, value recovery of minerals, a smaller footprint and less environmental impacts (Sellers, Picorelli and Salmi, 2022). What requires further investigation is the consequences of MLET implementation to host communities or community perspectives towards the proposed technology and subsequent delays in transition.

Aug 2, 2023