Search Documents

By Lance A. Roberts

Expansive soil formations can be found throughout the United States. When subjected to wetting, these formations have the potential to swell and exert large uplift forces on buildings and foundations. Lightly loaded structures, such as single family residences founded in areas of expansive soils, can be significantly damaged due to uplift movement from swelling actions. Designing an economical deep foundation that can resist uplift forces is critical to prevent damage to these structures. The current solutions to control uplift due to swelling soils, such as over-excavation and replacement of the expansive material or the use of drilled shafts can be costly. Piles made from recycled polymer materials could provide a solution. Due to a lower coefficient of friction along the interface of the soil-pile interface compared to traditional pile materials, solid recycled plastic piles can allow expansive soils to move nearly independently from the pile when wetted. This results in a much smaller magnitude of uplift force being transferred to the structure, which minimizes the risk of significant structural damage from excessive movements. This paper presents the results of research conducted on the use of recycled plastic piles in an expansive shale environment. The preliminary phase of the project involved the installation of six recycled plastic piles at a test site on the South Dakota School of Mines and Technology campus. Two of the piles were subjected to a full-scale compression load test in order to determine ultimate capacity. The remaining four piles were subjected to long-term monitoring of uplift movement during the course of the project. A concrete anchor was also installed at the test site for uplift monitoring. Data gathered during the field and laboratory testing was utilized in a non-linear soil-structure interaction model to predict the displacement behavior and internal stresses within a plastic pile and concrete anchor subjected to uplift forces from the swelling shale. While more research is needed to further understand the application for recycled plastic piles, the results from this research indicate that their use is a viable alternative for support of lightly loaded structures in expansive soil environments.

Jan 1, 2010

Industrial Minerals production in New Zealand is limited in both quantity and range, but imported in quantities that make New Zealand the world's biggest consumer per head of population. The use of industrial minerals is assured as both population and standard of living increase regularly. But to develop these minerals in the New Zealand environment requires the mineral, or its market (both local and export), to have characteristics that negate the remote geographical location. Volume and/or uniqueness can achieve this.

Jan 1, 1997

By R. Webber-Youngman

The Department of Mining Engineering at the University of Pretoria accepts that the process of teaching and learning improvement is an ongoing exercise with the ultimate aim to deliver well-rounded mining engineering practitioners. Various challenges impact on the success of this process. An integrated and innovative process was developed and is followed in the Department to overcome these challenges. The aim of the Department is to apply a holistic teaching approach by introducing multiple integrated interventions with regards to teaching and learning strategies. Three phases of this process are discussed in this article, and are illustrated in Figure 1. During the first phase, prior to 1999, several teaching and learning challenges were identified in the Department of Mining Engineering. These challenges are discussed in the next section. In the current phase, a variety of interventions to address the challenges are being developed, implemented (in some cases piloted), and evaluated. The future phases will focus on the improvement, successes, and full roll-out of current interventions, as well as on training, development, and support for all staff members to participate in the process. (Figure 1)

Jan 1, 2011

The tenth annual Mine Resale Evaluation was held in conjunction with the RMCMI 2001 convention at the Steamboat Springs Sheraton Resort, Steamboat Springs, Colorado June 23 through 26. The purpose of the mine rescue evaluation program is to provide an opportunity for mine rescue teams to learn new skills and improve their existing ones in a non-competitive environment. Several staged ?disaster? scenarios were held where the teams are called upon to exhibit their life saving abilities. The evaluators meanwhile are offering suggestions, both verbal and written, to help the teams better understand the situations presented them. This non-competitive environment allows the teams to work together and share their knowledge with fellow mine rescue teams providing everyone with a positive learning experience. Mine Rescue Chairman Bill Balaz, Balaz & Associates, was in charge of coordinating the events. Six teams consisting of seven to twelve members each (totaling 60 members) participated in the three-day event. Each ream was required to respond to direr different real-life scenarios plus a written general knowledge test daily. Cindy Burnham has assisted Bali, for a few years. Her responsibilities include grading all of the written tests. This year's tour professional evaluators included Art Seanz (Hazardous Ma¬terials) of Western Environmental Associates ; Guy Norton (Ropes), Guy Horton Rope Rescue; Mary Bailey (Medical), MBA Training and Morley Hense (Confined Space). Carolyn Durga, BHP Coal, also assisted in hazardous materials and medical scenarios. They each provided three different challenging mock situations per day per team. The teams had no prior knowledge of what the scenarios would be as details were provided only as they arrived. Ten volunteer victims added much drama and excitement to the event. Their realistic enactment, complete with false blood makeup and severed limbs, made for some very tense scenarios. The Mine Rescue Teams participating this year were BHP LaPlata, BHP Navjo, BHP San Juan, all from Farmington, New Mexico; Bridger Coal Co., Rock Springs, Wyoming; Sabine Mining, Longview, Texas; Solway Minerals, Green River, Wyoming and Western Energy Co., Colstrip, Montana. Many new friendships were made and much knowledge shared. A swap meet was held Saturday afternoon for the teams to exchange miscellaneous equipment, hats, shirts, etc. The trams were asked to evaluate the program and the evaluators. They responded with many positive suggestions that will help improve the upcoming events in the years to come. Culmination of the Mine Rescue program was a Tuesday morning awards breakfast where the teams were presented with trophies. Each member was also given a gold pin with the words Continuing Challenge - Ropes.' The pin was the first in a series that will be given over the next few years. The participating victims and evaluators were also commended for their outstanding efforts. Special signed "Victim" shirts were given to select volunteers. Sponsors for the Mine Rescue program were Flanders Electric Motors, Magnum Metals, Rocky Mountain Electric Motors, Sedona Consulting and Balaz & Associates. Many hours of volunteer tine and effort from various family members of participants helped make the 2001 event a huge success.

Jan 1, 2001

By William W. Aljoe

This report summarizes the Bureau of Mines noise-control research program from 1972 to 1982. Each segment of the mining industry--under- ground coal, underground hardrock, surface mining, and processing plants--has different noise-control problems because of vast differences in working procedures, equipment, and workplace design. The Bureau has identified the most serious noise problems in each segment and has developed strategies for attacking these problems. This publication points out the need for noise control in the mining industry, discusses Federal regulations governing worker exposure to noise, and describes the Bureau's overall approach to mining noise- control research. It traces the history of noise overexposure in each segment of the mining industry and discusses the major noise sources. It provides detailed information on noise-control research efforts in the Bureau's major areas of emphasis, including the results of these efforts. Finally, the report discusses the Bureau's future role in research on mining noise control, emphasizing the need to expend more effort on long term in-house investigations into the noise problems that have been identified in past programs as the most serious ones.

Jan 1, 1985

By Yongbao Zhu

The Ag2O-mediated reactions of cycloaurated compounds with a general formula Au(L)Cl2 (L = bi-dentate C?N ligand) with thiosalicylic acid, N-acetyl cysteine or 1,2-benzenedithiol in DMF proceeds via ligand substitution of the Au?Cl bonds to afford the S-O and S?S adducts all in good yields. The reactivity of the dichloro, S-O and S-S adducts towards thiols were examined by reacting with cysteine in an aqueous medium, revealing that all of Au-Cl, Au-O and Au-N are labile for thiol displacement. The measurement of the inhibitive activities of these compounds against human cathepsins B and K showed that the dichloro and S-O adducts are effective inhibitors with IC50 values ranging from 0.1 to 2.6 -M, and that the S-S adducts are inactive.

Oct 1, 2003

New Developments in Spirals and Spiral Plant Operations Records indicate that spiral separators have been utilised in mineral separation for over 100 years. The Spiral's predecessor, the sluice, has been in use for centuries in different forms and a spiral can be thought of as a sluice wound around a column. The spiral separator is distinguished from the straight sluice, and other flowing film separators, in uniquely introducing centrifugal motion. The elegance of the spiral concept was embraced due to significantly improved separation efficiencies, ease of operation and tolerance of variation in feed conditions. Advances in spiral technology have improved the metallurgical performance, modernised the materials of construction, increased unit capacities and simplified operation. These advances have ensured that spirals continue to play a major industry role amidst other advancing and competing technologies. Recent developments in spiral and spiral plant technology include: the launch of the VHG spiral model, specifically aimed at feeds with very high levels of high-density mineral particles; the introduction of a high capacity wash water spiral model; and innovations in feed stabilisation and control. Details of these developments are presented together with the resultant operational benefits including feed stabilisation, product control and improved metallurgical performances.

Sep 13, 2010

As the theme of the conference is ære-discover Otago' from the minerals point of view, it is also timely. Of the eight million ounces of gold recorded produced from Otago, perhaps a quarter of this came from the goldfields of St Bathans, Vinegar Hill and Cambrians. The most notable among them was the Kildare Hill Mine, which is the so-called Blue Lake at St Bathans today. The bottom wash encountered in this mine contained the famous Kildare lead, which averaged 7 1/2 dwt to the dish, and is still one of the richest leads of alluvial gold known in the world. The richness of this lead, the best encountered in these gold fields, is otherwise stated to have yielded more than 42 ounces of gold to the cubic yard. It should be borne in mind that this equates to about $22 000 per cubic metre, in todayÆs values. I have been told by older residents of this district that in fact about 1 million ounces came out of the Kildare mine and associated workings. In todayÆs values, this would be about 530 million dollars worth of gold. The largest mines in the district were at Surface Hill, Kildare Hill, Nicholsons, Vinegar Hill, the Never Fail claim at Shepherds Flat nearby, and at Cambrians. It would appear that in almost every case, work stopped when the bottom wash progressed too deep down dip of the anticline hills on which it was initially found. The mining methods were sluicing and hydraulic elevating, and although the gold bearing ground did not stop, eventually it exceeded the ability of the mining methods then available years ago, to work it further. When it is realised that the previous mining has removed what is likely to be only a low percentage of the gold resources in these fields, a tantalising situation presents itself today in that mining technology now available will enable another cut to be taken off these fields. As in the past, I believe this will be million ounce plus and multi-million dollar scenarios, where the economic and social benefits will become widespread prizes.

Jan 1, 1992

By T. Gammatikopoulos, C. Gibson, M. Aghamirian

Lithium is an alkali metal found in brine deposits in the United States, Chile and Argentina, as well as in hard rock deposits in Australia and North America. In hard rock deposits, spodumene (LiAl(Si2O6)) is the major economic lithium bearing mineral. Spodumene is typically upgraded through a combination of dense media separation, flotation and magnetic separation. One of the major spodumene concentrate quality specifications is the iron oxide content because it will help determine if the concentrate is considered ceramic grade for use in ceramics and glass or chemical grade for use in lithium ion batteries. The rejection of iron bearing silicate minerals from artificial ore composites (high amphibole and low amphibole, high quartz/feldspar) from a hard-rock spodumene deposit was investigated using magnetic separation and flotation. The efficacy of Wet High Intensity Magnetic Separation (WHIMS) in iron rejection was found to be dependent on the mineralogy of the iron-bearing silicate minerals including modal distribution, liberation and association. When magnetic separation was conducted prior to flotation, the Fe2O3 grade in the final flotation spodumene concentrate was reduced from ~3% to ~1% Fe2O3 , and improved lithium recovery in flotation was observed. It was determined that it was most effective to conduct WHIMS on the flotation feed after scrubbing and de-sliming because this reduced the required magnetic field to recover iron-bearing minerals, likely because slime coating was greatly reduced. Flotation collector screening of four different collectors with varying rosin acid content demonstrated a potential increase in selective flotation of spodumene over some iron silicate minerals with decreasing rosin acid content in the fatty acid collector. However, due to marginal difference in flotation results with the various collectors tested, further testing is required to confirm the observations made and establish a hypothesis regarding the effect of rosin acid content.

Jan 1, 2017

The work described herein is the opening phase of an extensive system of underground excavation undertaken under contract with a Malayan authority.The specifications called for the lining of all tunnels in earth or broken rock with circular segmented cast iron lining, similar to that of the London tubes, and it is the installation of these linings which it is proposed to discuss.Owing to the long deferred delivery quoted and the obvious need for speed of access to the internal installation, it was decided to defer driving the completed circular section and substitute two small timbered headings.These could later be opened out in turn to full section and lined without prejudice to traffic, since both of them had access to the internal workings.NATURE OF ROCKThe rock series through which the circular sections were driven consisted of:(a) A wide zone of intrusive porphyritic granite, consisting generally of orthoclase phenocrysts in a ground mass of micro pegmatite. This area showed advanced weathering, varying from a stage showing slightly tinted kaolin containing approximately 20% of small boulders to one of ultimate decomposition to pure kaolin;(b) A narrow zone of weathered augite diorite, consisting of rock masses of a maximum weight of some 100-150 tons, isolated by clay seams up to 1 ft. 6 in. in width.The whole area was in a state of quasi-hydrostatic equilibrium, which resulted in heavy pressure immediately after excavation. Freshly broken faces would appear to be quite solid but, within a few minutes, would commence to sweat and "slab off" under pressure and, unless support was placed promptly, the whole face would burst out and run from above. Mucking was slow, owing to the plastic nature of the clay and the ease with which it puddled into slurry.In zone (b) a good deal of trouble was experienced because of the fact that the somewhat heavy blasting necessary tended to cause movement of the large rock masses. Subsequent scouring out of the supporting clay bands by the waterflow permitted settlement of the ground on to the timbers and many reinforcing sets were therefore required.The timbering of the pilot headings and its relation to the cross-section of the circular tunnels is shown in Fig. 1. Top and side spiling was driven in the ordinary way, but in bad ground intermediate sets and breast boards had to be placed. These sets were usually withdrawn after the...

Jan 1, 1941

By G. A. Doyle

The quality of water in mine pit lakes depends in part on the physical limnology (Le. stratification, turnover, and development of anoxic conditions with depth) of the lake. Limnologic data collected from four existing pit lakes indicate that pit lakes develop a thermocline, or temperature stratification, in the upper 10m to 30 m of the water column. Two of the pit lakes (26 m and 55 m deep) undergo seasonal turnover of the entire water column, whereas two deeper pit lakes (110 m and 240 m) undergo seasonal turnover of only the upper portion of the water column. In the deeper lakes, seasonal mixing does not extend through the entire water column and a distinct chemocline develops with depth.

Jan 1, 1996

By W. F. Dietrich

1. On St. Thomas and St. Croix, and possibly also on St. John, low-quality red-burning clays probably can be developed to provide the major part of the raw materials for structural clay products and earthenware pottery. 2. The potential sales volume for structural clay products is too small to sustain a plant in the Virgin Islands to manufacture such products in competition with Puerto Rico; however, handmade patio tile might be produced successfully. 3. The market for pottery utility wares in the Virgin Islands is too small to justify a plant devoted solely to the production of such wares; but it may be feasible to evolve a diversified community activity to make jugs, pots, casseroles, bowls, charcoal burners, patio tile, and other items.

Jan 1, 1955

By Scott Rosenthal, Kyle Murphy

This paper discusses the trials and tribulations of obtaining Velocity of Detonation (VOD) readings in small diameter blast holes in an underground mine. Montana Technological University (Montana Tech) obtained a time-domain reflectometer (TDR) type VOD monitoring unit. Purchase of the VOD monitor was justified on verifying explosives performance used in Montana Tech’s practical underground mining class and provide a teaching aid for the school’s rock fragmentation class. Before demonstrating the unit to students, we figured we better learn how to use it first so we give the students an appropriate experience. Our first learning was in obtaining the correct coaxial cable for the VOD monitor and how to properly terminate the cable. Once the cable was on-site and terminated, VOD testing could commence. Use of the VOD monitor was tested underground in small diameter holes (1.5-inch, 38 millimeter) pneumatically loaded with ANFO. After a few failed trials, and follow-up discussions with the supplier, VOD readings were obtained for the ANFO loaded holes. Additional readings were obtained for a pre-split product and detonating cord to satisfy our curiosity that the unit was performing as specified by the manufacturer. This paper will share our learnings in the hopes that others can benefit.

By C Noble, J Webster-Brown

A survey of selected West Coast Streams was undertaken in Summer 2001, Summer 2002 and Winter 2002 to establish the degree of arsenic (As) contamination in waters and sediments downstream of old coal and gold mine workings on the West Coast. Of the catchments studied, Soldiers/Ford Creek and Rapid Stream showed the most significant elevated As concentrations, predominantly in dissolved form, and evidence of AMD or ARD contamination (high sulfate concentrations and/or acidity). The rate and processes of removal of dissolved arsenic from the water column (attenuation) have been studied in these catchments. The Rapid Stream and Soldiers/Ford Creek catchments are directly affected by adit drainage from the Sullivan and Blackball coal mines respectively. Both catchments have high As concentrations in the sediments, with up to 770 mg/kg in Soldiers Creek and 490 mg/kg in Rapid Stream. Dissolved As concentrations are significantly elevated in the neutral pH waters of Soldiers Creek; typically as high as 100 - 200 ¦g/kg, up to 500 m downstream of the main adit discharge (800 ¦g/kg As). Adit inflows to Rapid Stream were acidic and contained 20 - 30 ¦g/kg dissolved As, with relatively high concentrations of arsenic in the stream water in winter (up to 18 ¦g/kg), but not in summer. Analysis of concentration trends and As:SO4 ratios downstream of these obvious As sources confirmed that dissolved As had been actively removed from the water column, but varied seasonally with greater removal evident in summer. Adsorption of arsenic onto iron oxide in the stream sediments is the most likely mechanism of removal. The Snowy River catchment, on the other hand, has relatively high As concentrations in both the sediments and the water column, but there was little evidence of a distinct AMD or ARD input from the Blackwater gold mining area. Preliminary investigation suggests that dilution rather than attenuation is responsible for decreasing As concentrations downstream.

Jan 1, 2003

By A. McLean, M. Iwase, K. Wakimoto, K. Katogi, Y. Kikuchi

One of the greatest obstacles to the application of physical chemistry principles to the elucidation of slag-metal reactions is a lack of knowledge of activities of the reacting species. To a large extent, oxygen potential of the slag phase governs iron and steelmaking practice. Without oxygen control by means of appropriate sensors, the behaviour of the other elements cannot be managed. In this paper, measurements of the FeO activity with various types of electrochemical FeO sensors will be described together with examples of their applications for improved strategies toward better practice for ladle metallurgy and sulphur and manganese distributions between slag and metal phases during steelmaking. Measurements of FeO activity have also been made in order to improve dephosphorization reactions. This type of work has led to significant reduction in volume of slag generated within the steelmaking vessel, which in turn has important implications for refractory wear, metal yield, alloy recovery and improved productivity. Finally, an on-line sensor is described that permits the oxygen potential to be determined for both the metal phase and the slag phase during steelmaking in the BOF.

Jan 1, 2004

By B. W. Gandrud, A. C. Richardson

"INTRODUCTION The Bankhead mine of the Cane Creek Coal Mining Co. is in the central part of Walker County, Ala., 4 miles south of Jasper. The Mary Lee bed in this part of the State yields a practically free-burning coal which is marketed as a. steam-raising and domestic fuel. As mined, the coal ordinarily contains ash-forming impurities to an extent that makes it necessary to treat the coal by some washing process before it is marketed. At present the Bank-head coal coarser than 3-1/2 inch is hand-picked and the coal finer than 3-1/2 inch is washed in two single-compartment jigsThis paper contains the result of screen-sizing and float-and-sink tests on a representative sample of the run-of-mine coal and the results of tests made to show the amount of coal liberated from impurities by crushing the coarser sizes. .This report is one of a series on the washability of Alabama coals which is being prepared by the U. S. Bureau of Mines and the University of Alabama, with the cooperation of the coal producers of Alabama.SAMPLING AT THE MINE'The Mary Lee bed at Bankhead consists of two benches separated by a rock parting which varies in thickness from place to place in the mine. The top bench has a very uniform thick-nest; throughout the workings and yields about 65.0 per cent of the output. The bottom bench varies greatly in thickness and in nary places becomes too thin to work at a. profit. The sample for the washability study was taken underground at a place which was typical of the mine as a whole. In taking the sample the working face was squared up and a representative section out from each bench. Care was taken to secure a, quantity of coal from each bench proportional to the quantity contributed to the mine output. The rock parting as gobbed in accordance with the usual mining practice. The total sample taken weighed 3 tons."

May 1, 1933

By J. C. Stankus

Accurate evaluation of stress and geological conditions is critical to ground control design in underground openings. For a slope entry, the problem is more difficult because a slope will transverse through many different types of strata. Over the past three years, Keystone Mining Services, LLC, an affiliate company of Jennmar Corporation, has developed a new methodology designated the ?Stress, Geologic, and Support Design System (SGSsm)?. This patent pending method analyzes the stress, geology, and support design for a mine slope. It has been successfully applied in various new slopes across the United States. This paper will detail the main concepts of the methodology including: (1) Analysis of stress and geology and identification of strong, fair and weak zones along the slope; (2) Primary and supplemental support design; (3) Long term support design in the form of steel square sets or arches, and (4) Validation of the support design utilizing advanced finite element computer modeling.

Jan 1, 2011

By H. Yilmaz

Tensile strength testing has been one of the most common physical property testing methods of thin spray-on liner (TSL) products worldwide. However, the variety of products tested has been insufficient for comparison purposes. Specimen preparation procedures and test parameters such as curing time and loading rate are not reported well. Comprehensive tensile strength testing on 20TSL products and one plain shotcrete brand was performed over 28days of curing period. Detailed information on the test procedures with particular attention on the important aspects during sample preparation and test execution are provided. As expected, the tensile strength increases with increasing curing period. The test results make the categorization and comparison of liner products possible.

Jan 1, 2010

Failure of rock materials is a process of crack propagation. Crack initiation takes place when the crack tip stress intensity K reaches a critical value called fracture toughness, K1C. The rock fracture toughness is known to be affected by the surrounding environment such as temperature, confining pressure and humidity. In order to examine the effect of humidity, a series of semi-circular bend tests were performed under various water vapour pressures in a rock material that is known to be anisotropic. Water vapour promotes stress corrosion of rock and therefore the fracture toughness was found to have a decreasing trend with increasing water vapour pressure. The rate of decreasing the fracture toughness depends on the microcrack density that promotes the migration of water vapour into the rock. Also in an anisotropic rock, the fracture toughness depends on the direction of crack in relation to the anisotropy of the rock material.

Dec 6, 2010

By M. Proulx

"RÉSUMÉ Le diagramme ternaire Al2O3-Sr-Y est un nouvel outil servant à l’exploration de gisements de sulfures massifs volcanogènes (SMV) archéens. Le diagramme permet de discriminer entre les roches volcaniques à minéralisations à zinc dominant (domaine Zn+) et celles à minéralisations à cuivre dominant (domaine Cu+), ainsi que les roches volcaniques ayant subi une chloritisation hydrothermale pouvant aboutir à la formation de chloritites associées aux cheminées d’altération (domaine Cl+). Ces trois domaines délimitent des zones d’influence géochimique ou d’empreintes hydrothermales résiduelles ou fossiles produites par les cellules de convection hydrothermales générées par des magmas. Le diagramme permet aux sociétés d’exploration de déterminer de façon peu coûteuse la fertilité potentielle des roches volcaniques archéennes en ayant recours à leurs bases de données et aux résultats de leurs analyses de terrain, sans aucune manipulation des données. Le diagramme ne s’applique pas aux SMV aurifères.ABSTRACT The tertiary diagram Al2O3-Sr-Y is a new tool to explore Archean volcanogenic massive sulphide (VMS) deposits. The diagram can be used to discriminate between the volcanic rocks where zinc is the dominant mineralization (Zn+ domain) and the rocks where copper is the dominant mineralization (Cu+ domain), as well as the volcanic rocks that were subjected to hydrothermal chloritization that could have led to the formation of chloritites associated with alteration chimneys (Cl+ domain). These three domains define the zones of geochemical influence, or residual or fossil hydrothermal footprints produced by hydrothermal convection cells generated by magmas. Exploration companies can apply the diagram to determine, at low cost, the potential fertility of the Archean volcanic rocks by using their databases and the results of their field analyses, without any data manipulation. The diagram does not apply to gold-bearing VMS deposits."

Jan 1, 2015