Search Documents

By T. R. Wildeman

"At the Big Five wetland, which was built to treat drainage from a metal mine, encouraging results have attributed to sulfate reduction. Cu and Zn were reduced to below detection limits of 0.50 mg/L, Fe was reduced by at least 90% to below 3 mg/L, and the pH was raised from below 3 to above 6. The study showed that treatment was primarily through microbial processes within the substrate and that plants were not needed to insure success.Constructed wetlands can be taken through design and proofing stages, and into operations scale in a meaningful time frame for on-line acid drainage remediation. In staged design, laboratory experiments are initiated to determine reasonable substrate materials for remediation of a particular drainage. When a reasonable substrate is found, bench scale experiments are initiated as the next stage in the design. In these studies, removal efficiency, permeability, and flow are analyzed to identify candidate substrate which will support sulfate reduction and be hydraulically reasonable. Using this design method at one site, an acid drainage of pH 2.5 was raised to a pH of above 7. Total heavy metal concentrations in this drainage exceeded 900 mg/L. In the pilot constructed wetland Cu, Zn, and Fe were reduced by 99%.Determining how well these anaerobic cells operate in the winter is done at the pilot plant site in Idaho Springs, CO. It's been found that over the last four winters, those cells that emphasize anaerobic removal within the substrate have operated continuously and effectively the year round. Winter operation is aided by the fact that the water temperature of the acid drainage is always between 14 and 16° C, and the cell can be readily insulated from the cold. Activity of the sulfate reducing bacteria may decrease during the winter. However, it appears that organic complexation of metals helps to maintain low concentrations of metals in the effluent."

Jan 1, 1992

Recently published extensions to the mill-dump cutoff grade theory for joint open pit-concentrator operations lead to equations that must be simultaneously satisfied as a necessary condition for an optimal operating policy. These equations are parametrically dependent upon ore quality parameters, other than grade, relating to the ease of recovery of the disseminated mineral in the concentrator. Since it is not possible to treat quantities of ore corresponding to the size of selective mining units separately in the concentrator some mixing is inevitable and often deemed desirable in the interest of homogeneity of mill feed. This renders the calculation of cutoff grades for individual mining units futile; mining units must be grouped to form larger parcels that can be dealt with separately. In doing so an opportunity cost may be incurred; the loss of potential benefit that would result from such separate treatment. This matter is considered from a theoretical, qualitative, point of view. A numerical example then shows that a significant variability in the quality parameters can be tolerated without incurring such opportunity cost, provided sufficient knowledge is available concerning the distribution and effect of these variables to enable the use of effective mean values of these parameters in the cutoff grade calculation. Lack of such knowledge can have major consequences for the economics of the operation.

Jan 1, 1981

By A. S. Murphy, E. V. Manlapig, C. Green, J. W. Parkinson

Historically in Australia and the United States many coal mines deposited raw wash plant fines into large slurry impoundments. At the time the technology and market economics did not exist to make it viable to recover coal from these tailings. Today better technology exist to dredge and clean the tailings and there are circumstances where government regulations and market forces have come together to make coal recovery from these old tailings impoundments economically viable. This paper discusses the processes and equipment being used in tailings impoundment reclamation operations in Australia and the United States, and discusses the economic forces driving these operations.

Jan 1, 2001

By Brian Fulcher

In April 1997, Kiewit/Parsons Brinckerhoff (K/PB) completed the 7,600-m (25,000-ft) primary access tunnel for the Yucca Mountain, NV proposed high-level nuclear waste site. K/PB then began boring an exploratory east-west cross drift tunnel at the site. The 2,681-m (8,796-linear ft)East-West Cross Drift Tunnel was excavated through volcanic tuffs having zones of incompetent rock using a rebuilt Robbins 5-m (16.4-ft)hard-rock tunnel boring machine(TBM) with a special arrangement of supporting equipment. This portion of the Yucca Mountain project was completed in eight months.

Jan 1, 2000

Baja Mining is currently constructing the Boleo metallurgical plant in Santa Rosalia, Mexico to recover copper, cobalt, zinc and possibly manganese products from the Boleo ore. The process involves an acid seawater leach of the whole ore followed by solid-liquid separation and washing of the leach residue. Solvent extraction is used to separate copper, cobalt and zinc from solution. Copper and cobalt are recovered as cathode metal products and zinc as a zinc sulphate monohydrate. Manganese may be directly precipitated as manganese carbonate which can be used as a feedstock for manganese metal production. Laboratory testing has continued to refine various aspects of the process including iron removal, cobalt and zinc solvent extraction, cadmium cementation, cobalt electrowinning and manganese metal electrowinning. The results of this testing are reported in this paper.

Jan 1, 2012

By W. Kunda

Silver nitrate solution is a very common product in hydrometallurgical processes involving the treatment of various silver bearing materials. Silver is recovered by electrolysis. The alternative method for the recovery of silver from aqueous solutions is the precipitation by hydrogen at elevated temperature and pressure. A previous study by the authors revealed the feasibility of this technique for the silver ammine sulfate system. Further study showed different behavior for silver in the silver ammine nitrate system and a systematic study was initiated to establish the optimum conditions for the process. The study showed that the process can be controlled by (1) composition of the feed solution, (2) temperature and (3) hydrogen pressure. The recovered silver product was in the form of very fine powder.

Jan 1, 1989

By Ivan E. Goodner, Charles H. Fulton

THE subject of the constitution of copper-iron mattes has received considerable attention in recent years by Keller,1 Bolles,2 Hofman,3 and Gibb and Philp.4 Still more recently Friedrich, Röntgen, Wiedmann, Heyn and Bauer, and Leroux have published, in some instances, elaborate researches on the various systems of the sulphides, and the sulphides and their respective metals, which enter into the constitution of mattes, and have added very greatly to the knowledge of the subject. The work of Friedrich has been especially fruitful. But to date no effort has been made to correlate the data obtained in the latter researches and apply then to the study of the product called " matte," which is made in such large quantities by copper and lead-smelters. In this paper we propose to determine, by metallographic and chemical means, the constitution of copper-iron and copper-lead mattes in the light of the recent data above mentioned. We do not discuss copper-nickel mattes or speisses (artificial arsenides). The paper is divided into three sections I. A review and discussion of the various binary systems of the metallic, sulphides, and the binary systems of various metals and their respective sulphides entering into the constitution of mattes; also a discussion of the physical and chemical properties of these sulphides. II. A description of the results obtained from the chemical and metallographic examinations of the samples of copper-iron and copper-lead-iron matte obtained from various plants.

Nov 1, 1908

By J Pric, M Fulton, C Xia

A cyanidation study was conducted on a mild refractory gold ore sample from the Central zone of Clarence Stream Property, owned by Freewest Resources Canada, to develop a leaching strategy to extract gold. Gold, at a grade of 8.00 g/t, is present as native gold, electrum and aurostibite. The ore also contains 2.8 per cent pyrrhotite, together with several antimony minerals (0.8 per cent berthierite and gudmundite, 0.18 per cent native antimony and stibnite). It also exhibits weak preg-robbing properties with 0.16 per cent organic carbon. Aurostibite, a gold antimony compound, is particularly known to be insoluble in cyanide solution. The antimony dissolves in cyanide solution to form antimonates, which retards gold dissolution. Industrial practice of extracting gold from aurostibite generally consists of producing a flotation concentrate, which is leached in a pipe reactor at low alkalinity and high oxygen pressure with about 20 g/L cyanide. The proposed new approach is efficient and allows the extraction of gold directly from an ore at atmospheric pressure and a low cyanide concentration at pH 10.5. The effects of grinding, pretreatment, lead nitrate, kerosene and cyanide concentrations have been investigated. The maximum gold extraction obtained on the ore was 87.9 per cent using 800 ppm NaCN, 500 g/t lead nitrate, 30 g/t kerosene, DO 10 ppm and pH 10.5 in 168 hours. The associated cyanide consumption was 1.3 kg/t. The additions of lead nitrate and kerosene increased gold extraction. In comparison to a P80 of 74 ¦m, a P80 of 30 ¦m significantly increased gold extraction. Gold in solid solution in gudmundite and arsenopyrite was believed to be responsible for the unleached fraction until mineralogical analysis of hydroseparation concentrates of leach residues showed that most of the unleached gold occurs as aurostibite, either as locked grains in sulfides/sulfarsenides or as grains with passivation rims of an Au-Sb-O phase. Coarse gold was also found. Gold extraction was not sensitive to cyanide concentration from 250 ppm to 1200 ppm NaCN and high pH was detrimental. Decreasing the cyanide concentration reduced the cyanide consumption to 0.85 kg/t. The removal of coarse gold using a Knelson concentrator and a Mosley table prior to leaching increased the gold extraction to 90.4 per cent (leach residue at 0.77 g/t).

Jan 1, 2007

By D. M. Doyle

A study of the various components contributing to energy costs and their relationships to generally trended operating data, such as tonnage, operating costs, etc., over progressively shorter time periods provides information for an energy audit. A study of annual data gives some insight into the importance of various energy components. As the time frame of the study progresses through monthly, daily and, finally, into quarter hourly data, the variations become more evident and, most important, strategies develop to minimize energy costs. The results of an audit conducted during the summer of 1978 at Wesfrob Mines Limited are reported to illustrate this important phase, prerequisite to a meaningful energy cost avoidance program. The balance of the paper deals with the energy conservation program at Falconbridge Nickel Mines Limited's Sudbury operations, the metering and control equipment, the commitment, the new energy accounting practices and, lastly, the policies. Examples of successful energy conservation endeavours include automatic peak electrical load control, waste heat recovery from mine air and compressor cooling water, energy reductions resulting from lower building temperatures and curtailment of idling loads. The use of pulse meters to measure the flow of gas, steam, compressed air and electrical energy, with their signals interfaced to process computers, allows monthly, daily and, if necessary, immediate reporting of energy and energy per unit of production information The program so reported at Falconbridge's Sudbury Operations is credited with an annual cost avoidance of .9 million dollars in a 14.0-million-dollar annual energy account

Jan 1, 1979

By P. den Hoed, R. I. Rambiyana

"Four sulphide minerals - pyrite (FeS2), pyrrhotite (Fe1-xS), pentlandite ([Ni,Fe]9S8), and chalcopyrite (CuFeS2) - contain the base metals and most of the iron in concentrates of platinum group metals (PGMs). In the pyrometallurgical processing of PGM concentrates these sulphides form a matte during smelting, and iron and sulphur are removed from the matte during the converting process. This paper discusses the roasting of Merensky concentrate in air before smelting, with the purpose of reducing the matte load to the converter.Roasting tests were conducted in a bench-scale rotary kiln at temperatures from 350°C to 700°C. The concentrate tested contained 17.4% sulphur and consisted of 23% pyrrhotite, 16% pentlandite, 11% chalcopyrite, and 2% pyrite. The particles were fine (d50 = 22 µm), and all the sulphide particles were liberated. Roasting in air at 550°C and 650°C for 20 minutes removed respectively 60% and 70% of the sulphur. The iron in the sulphides was oxidized to Fe3O4 (magnetite) at temperatures below 500°C and to Fe2O3 (haematite) at temperatures above 550°C. At 700°C the bed sintered and copper oxides formed. At temperatures below 450°C oxidation was incomplete: pyrrhotite remained and only 30% of the sulphur was removed. Smelting tests were conducted to assess matte fall and the deportment of copper and nickel to matte. It was evident that roasting resulted in lower matte falls (a drop of approximately 60%) compared with matte falls from unroasted concentrate. The iron and sulphur levels in the matte were reduced to below 3.5% and 22% respectively.This paper also briefly describes the mechanisms by which pyrrhotite, chalcopyrite, and pentlandite are oxidized during roasting. For chalcopyrite, the mechanism proceeds through an intermediate solid solution phase, which extends from Cu1.02Fe1.04S2 to Cu2.04Fe0.72S2 to a copper-rich solid solution of bornite (Cu4Fe1.4S4-Cu2S). The oxidation of pentlandite proceeds through a monosulphide solid solution (Ni0.39Fe0.53S-Ni0.74Fe0.15S) to a solid solution of heazlewoodite ([Ni,Fe]3}xS2). These mechanisms are explored in relation to chemical thermodynamics and microstructures."

Jan 1, 2015

Multiple regression analysis was used to predict elemental concentrations of copper and nickel in soils from consideration of the concentration of these elements in vegetation in an ultrabasic complex in New Zealand. Regression equations were computed from sixteen independent variables involving concentrations of ten elements in plant ash, and various physical factors such as slope and altitude of the site, and height of the tree. One elemental and one physical variable were significant for nickel at the 90 per cent level of probability and five elemental and two physical variables were significant for copper at the same level. Use of the regression equations explained 32·5 per cent and 26·5 per cent of the variance in the respective relative accumulations (amount in plant divided by amount in soil) of copper and nickel.Predicted concentrations of copper and nickel in soils agreed more closely with the observed values in the soils than did the levels of these elements in plant ash.Although the results may specifically apply only to the test area, the principles should have universal application.

Jan 1, 1972

This paper characterizes the copper cycle, that is, the flows of copper entering and leaving the African economy over a one-year period (1994). The major flows over the entire life-cycle of copper are examined; these include production (mining, milling and refining), fabrication of semi-products and manufacturing of finished products, use, and the waste management system. The results reveal that substantial amounts of copper (of order705 Gg/yr) are mined in Africa; of that amount, about 70 per cent is exported following processing, 18 per cent is utilized by African fabricators, and 12 per cent is discarded. The flows of copper products from African fabricators and product imports from other continents exceed product discards by large amounts. This difference, about 0.25 kg Cu/capita/yr on average, is added to in-use stock, largely as wire, plumbing tube, and in electronics. Some 65 per cent of the copper in discard flows is contained in electrical and electronic products, where it is relatively easy to collect and process for reuse. About a third of the copper discard flows known is recycled. The actual percentage is almost certainly higher because of informal (and unrecorded) recycling. Much of the remaining discarded copper is diluted into the municipal waste stream, where recovery and recycling are probably not economically justified. Keywords: material flow analysis, resource management, material budgets, copper, stocks and flows, systems analysis, Africa, developing country

Jan 1, 2003

By William H. Schiffbauer

One of the safety and health research programs of the former U.S. Bureau of Mines Pittsburgh Research Center was the evaluation of technology that will provide remote-controlled operation of mechanized equipment in underground room-and-pillar mining. The purpose of this effort was to enable workers to be located away from the hazardous and unhealthful coal extraction area (the face). As part of this program, advanced machine navigation and control technologies were developed for underground room-and-pillar and highwall coal mining that can be applied to commercially available mining equipment. These technologies use off-the-shelf components and a flexible control software architecture to minimize the effort required to adapt them to mining equipment. An accurate, reliable navigation system that can provide the mining machine's heading and location is a critical requirement for a remote-controlled mining system. After investigating several different types of navigation sensors, researchers selected the Honeywell Ring Laser Gyro Inertial Navigation System (INS) as showing the most promise. It was installed on a continuous mining machine at our Mining Equipment Test Facility. Extensive testing at an open pit (OP) site was also performed. This report describes the INS as it was employed on the mining machine in the laboratory, in the field, and OP tests, and provides the accuracy and performance results of the OP and highwalltests.

Jan 11, 1997

In November 1999 Waihi Gold Mining Company commissioned its new crushing and conveying plant used to transport both ore and waste from the Martha Mine to its ore processing plant and also its tailings dam construction area. To date, a record monthly throughput of 854 000 tonnes throughput has been achieved. This paper outlines the measures taken subsequent to the commissioning of the system to achieve greater than design throughput and to mitigate the environmental and safety issues associated with operating the system in the middle of a town.

Jan 1, 2001

By Lawrence G. Houk

Lithium is the lightest of all metals, but as it deteriorates rapidly in air it has no structural applications. Alloys of lithium that will float upon water can be made with other light metals, but these ultralight alloys are not useful in aircraft production or elsewhere at present. Alone or alloyed with alkaline earth meals, lithium acts as reining agent on molten metals, and as a minor constituent with other metals it imparts characteristic properties to the allay. Lithium compounds have somewhat wider application in commerce than either the metal or the alloys. They are used in the glass, ceramic, chemical, and air-conditioning industries and less extensively in the optical, pharmaceutical, electrical, and textile industries. The United States is the leading producer anti consumer of lithium ores and compounds and apparently has the largest known ore reserves. The value of lithium ores and primary chemical byproducts produced is relatively small, yet the lithium chemical industry yields products worth hundreds of thousands of dollars each year, owing partly to the high degree of purity demanded by the trade for most finished products and to the low combining weight of lithium. Fortunately, the low-grade ores can now be concentrated economically, and this fact, together with our extensive reserves, assures adequate supplies to meet any reasonable increase in demand. Lithium is listed as essential by both the American and British war agencies, and its military importance may be greatly enhanced.

Jan 1, 1942

By M. Moagabo

CO2 emissions from carbonate laden reclaimed mine spoil has been shown to pose a hazard to residents in homes built on or adjacent to such land. The objective of this project was to develop a soil CO2 flux survey protocol for assessing reclaimed mine land. The research involved CO2 chamber accumulation flux surveys; stable carbon isotope ratio analysis; statistical hypothesis testing to examine correlation between CO2 flux and soil temperature and moisture as well as spatial dependence; and geostatistics to map CO2 and delineate high flux zones. Soil temperature was observed to have a positive correlation with fluxes while soil moisture was observed to be negatively correlated. Spatial dependence of CO2 fluxes on reclaimed mine land was observed on one of the two study sites. The research suggests that macro-porosity and gas permeability may be important factors that explain CO2 migration in mine spoil. A flux survey protocol has been developed, based on these results, for reclaimed mine lands. The work demonstrates the capability of geostatistical methods to delineate high flux fields. Further research will be required to determine suitable thresholds for such analysis.

Jan 1, 2012

By T Goswami

The conventional practice in open cut coal strip mining has been to blast the overburden or coal layers in separate blast events. This is done in order to maximise the benefits from throw blasting and also to limit coal losses. Each blast event usually has a particular design of hole diameters, burdens and spacings, explosive charges and blast timing in order to achieve the required blast outcome for either the overburden or coal. This means that each blast has to be separately cleaned on the surface after excavation of the previous blast. Hole locations then have to be individually surveyed and marked, holes drilled, explosives and initiators loaded and the blast fired. Each of these actions takes considerable time and resources and therefore impacts on mine productivity. The mine has to be cleared for each blast event and every blast presents a new potential source for noise, dust or vibration disturbance to the neighbouring population. Exposed highwalls are also subjected to vibration and damage from each subsequent blast event

Jan 1, 2006

By W. J. González

"With the increasing demand for minerals, technologies to maximize mineral recovery are paramount to a mine’s economic success. Many mining process waters have the potential to form calcium-based inorganic scales, which inhibit effective mineral recovery. Often, the solution to inhibit these deposits is the implementation of a chemical antiscalant program. This paper examines the application of a fouling analyzer to continuously monitor the formation of inorganic scale in mining process streams. The fouling data can be used to compare antiscalant programs and to optimize antiscalant feedrates. Case studies validate the ability of this technology to help optimize mineral recovery processes.INTRODUCTION The mining industry uses significant quantities of water. From quarrying, to crushing, to flotation, leaching, and refining, water is often the integral motive force to move slurries, separate or agglomerate fines, and extract and purify minerals. As well, water is used in a number of ancillary applications at mines, including dust suppression, gas scrubbing, and utility processes such as boiler, cooling, and waste water operations. For many processes, the quality of water being used is inconsequential. However, for certain processes, such as flotation, leaching, and desorption / stripping, water quality plays a key role in the ability of the operation to economically recover the target minerals. Dissolved solids such as calcium and magnesium salts can concentrate in process waters, exceed their solubility limits, and precipitate as scale on metal surfaces such as feed and transfer pumps, piping, and equipment. Some of the more common scales that form in mining operations include calcium carbonate (CaCO3, or calcite) and calcium sulfate (CaSO4, or gypsum), and to a lesser extent, calcium and magnesium silicate compounds. Any scale that deposits in a process stream will negatively impact mineral recovery, and increase the operational costs of the mine site. Whether it is acid washing a scaled heat exchanger in a carbon strip at a gold operation, replacing plugged emitter tubes in a leaching operation, or hydroblasting process lines in a scrubber unit, there are costs associated with labor, cleaning chemicals, repairs, and replacement parts. These costs pale in comparison to the potential costs of downtime and lost production, should the scale deposits occur in a process that is critical to the recovery of the target mineral."

Jan 1, 2014

By T. Proietti, L. Mongiovì, L. Simeoni

Reliable estimates of the kinematic characteristics of movements are obtained by using a statistical model SSM. This model represents a useful tool for the management of alert and alarm systems. L'élaboration des données du déplacement médian d'un modèle statistique SSM opportun fournit des estimations fiables des caractéristiques cinématiques du mouvement. Le modèle peut être ainsi utilisé pour la gestion des systèmes d'alarme. Die Bearbeitung von Bewegungsdaten anhand eines geeigneten statistischen Modell SSM ergibt vertrauliche Abschätzungen der kinematischen Eigenschaften der Bewegung. Das Modell kann also für das Management von Alarmsystemen verwendet werden.

Jan 1, 2003

By Frank Chase

Longwall mining has gained the reputation as being the safest extraction method in underground coal mines. However, one of the most difficult tasks associated with longwall mining is moving the face once a panel is completed. Based on Mine Safety and Health Administration (MSHA) fatality reports since 1996, longwall face recovery operations have claimed the lives of 5 U.S. miners and have resulted in numerous injuries. Recovery operations can be hazardous because they involve moving large pieces of equipment in very confined spaces. They are also conducted in highly stressed ground conditions due to front abutment loads generated by panel extraction. Shield removal is the most hazardous operation during face recovery because miners are constantly exposed to the unpredictable gob edge. To protect the miners, one or more walking shields, cribbing and/or other supplemental roof and standing supports are typically employed as breaker line supports as each shield is removed. At the Harris No. 1 Mine in southern WV, mobile roof supports (MRS?s) have been used in lieu of traditional walking shields on 17 face moves since 1997. MRS?s are shield-like support units mounted on crawler tracks and are commonly used during room-and-pillar retreat mining operations. For longwall recovery, the two biggest advantages that MRS?s have over traditional walking shields are that they are remotely controlled and are highly maneuverable. MRS?s have contributed to safer shield recovery and shorter move times at the Harris No. 1 Mine. This paper will address both the safety and the operational issues associated with MRS usage during shield recovery. It will also discuss new developments, including the use of the inherently safer battery powered MRS?s, which have been recently certified by the Mine Safety and Health Administration.

Jan 1, 2007