Search Documents

By B. Yu, N. Verbaan, A. Mezei

The recent 20 years witnessed a boom and bust in the nickel laterite industry. Most notoriously is the story of the first three Western Australian nickel laterite projects which all suffered major ramp-up issues. Many hard lessons were learned by the industry and it has been widely reported that the major contributing factors included insufficient testing as well as a limited understanding of the materials handling characteristics at the front-end stage of the flowsheet. This paper compares the current "race to production" in the REE industry to the laterite industry 20 years ago and addresses the fundamental question: ‘Have mining and exploration companies with rare earth projects learned from past lessons and are they doing sufficient and appropriate testwork to prevent failure’? The authors will provide the perspective of a commercial metallurgical laboratory that has gone through the laterite cycle and is active in the present REE cycle.

Jan 1, 2014

By G. S. Scott

In the course of the investigation into the causes, behavior, and control of mine fires, which the Bureau of Mines is now conducting, some attention was given to the subject of spontaneous heating. It is self-evident that the temperature of a pile of broken coal will rice if the rate of generation of heat exceeds the rate of brat dissipation and will fall if the opposite is the case. Factors that affect the rate of generation of heat are:

Jan 1, 1941

By Nelson Severinghaus

Mineral fillers have been defined as inert materials that are included in a composition for some useful purpose. Because this definition and the scope of this review are not specific- indeed, exceptions abound-accurate total statistics are unavailable. One source estimates the total production in the United States in 1971 at 5 million tons valued at $200 million, averaging $40.00 per ton. Included are a broad group of minerals-asbestos, barite, bentonite, calcium carbonate, clays, diatomite, feldspar, micas, silica, talc. Additional references will be made to synthetic mineral-derived fillers such as aluminum hydrate, precipitated calcium carbonate, and pyrogenic and precipitated silicas and silicates. A section on related uses at the end of this chapter covers absorbents and filters. Mineral fillers can be included in compounds to accomplish a variety of final results. Hardness, brittleness, impact strength, compressive strength, softening point, fire resistance, surface smoothness, electrical conductivity, and a host of other physical characteristics may be modified by the inclusion of fillers. These effects are the result of properties of the fillers, including chemical activity, hardness, particle size, shape and distribution, surface structure, color, density, and refractive index. To facilitate an overview of the mineral filler industry, this chapter will review the general usage of fillers, the inherent characteristics that intensify their utilization, and similarly their manufactured characteristics. Major using industries will then be examined in detail. Specific information on deposits and processing for industrial minerals will be found in the appropriate commodity chapter. The chart in Table 1, updated from the 3rd edition of Industrial Rocks and Minerals, illustrates the major mineral fillers (both natural and manufactured) and their more important end uses.

Jan 1, 1975

By Daven N. Compton

The optical properties of Au nanoparticles have been known for some time, with both Au colloids and Au nanoparticles embedded in glasses having been extensively studied. In this study, Pt nanoparticles have been incorporated into Au colloids, and the linear and non-linear optical properties investigated. UV-VIS spectrophotometry, fluorescence spectroscopy and the z-scan method have been used to examine the effects of such additions.

Oct 1, 2003

By Bill Linville

During fiscal year 1969, the Bureau of Mines was engaged in 66 projects to improve methods for producing and utilizing petroleum. Programs directed toward the continued conservation of this natural resource, including crude oil, natural gas, and oil shale, were carried out through research performed at four laboratories supervised and supported by administrative personnel of this Bureau of the Department of the Interior. Over 100 technical papers and reports were published by the Bureau or others based on this research, and numerous other reports were prepared for U.S. Government agencies, State agencies, and organizations of the petroleum and natural gas industry engaged in cooperative research programs with the Bureau.

Jan 1, 1971

Provide optimum visibility of mining operations while maintaining protection and comfort for ma-chine operators. Approach Cabs and canopies with hydraulically powered variable-height control were developed for several machines and tested in underground mining operations. How It Works From his position in the cab, the operator can raise or lower the cab, selecting a height that offers either more visibility of the working place or greater clearance for tramming. The entire cab enclosure moves up and down on guide rollers that ride on a pair of rails, and is actuated by a hydraulic cylinder controlled from within the cab. Normal working heights, for each of the four different cabs developed, are with the cab bottom from 6 to 8 inches above the mine bottom. A typical range of elevation (excursion) afforded by this design is shown in Figure 1.

Jan 1, 1978

By Kenneth Eilerts

[Efficient and econonic production of ?etroleum requiros knowledge of the propertios of rescrvoir fluids a:$. their characterintics of flow throayh porous forclntions. The cllanga in propertie s and flow characteri s- tics of fluids when their corosition is altercd cs a rnsult of reservoir- pressure decliae is of 'mecial i~ortenct? ir, planning wall-spaAng pro.yama and production schedules. Rct~ntion of the ~eatent poscible quantity of dissolved gac in the rescrvoir liquid gnneml'y is recognized cs ess~ntisl to mxim ultimzte recoverj of oil fro3 the underground reecrvoir. Ilo:rever, pro6uction mothodn tending to mintain gis in solution in the oil and re- sulting in the optimm ocolo~ic recgvery of oil not only vary from field to fiold but also my have to be changed from time to time in a given field as it is being depleted of its recoveraklo oil. Const vestly there is need tc investigztc tY.e propertiec of resa:-voir f kids corresponding to successivc stages of reservoir depleJ&ion with the view of obtnining infomation oacential to efficient prcriuctian practices.]

Jan 1, 1939

By André Laplante, Robert C. Dunne

"The role of flash flotation in precious metal recovery is reviewed. Interacting flash flotation and gravity recovery is discussed. The GRG test can be used, when linked to the behaviour of gold in grinding and classification units, to predict the recovery of GRG by flash flotation. The Cadia mill in New South Wales is used as a case study of circuit design, performance and simulation. It is shown that high throughput coarse grind applications such as Cadia require very effective fine GRG recovery systems in the primary grinding loop, which are more consistent with flash flotation than batch centrifuge concentrators (BCCs). BCCs can effectively recover a significant fraction of the GRG from flash concentrates, as predicted by laboratory testing and confirmed at a growing number of mill sites.INTRODUCTIONThe GRG test was designed to characterize Gravity Recoverable Gold (GRG) ten years ago (Woodcock and Laplante, 1993; Laplante et al, 2000), in response to the need to predict how much gold could be recovered from the main circulating load of grinding circuits using centrifuge concentration. The amount of GRG is not itself a prediction of gravity recovery: the performance of a gravity circuit nested in a circulating load also depends on the type and size of unit used, how much of the circulating load is treated, and how many times GRG is recycled and presented to the recovery circuit. The GRG test was first used in a simulator to predict gravity recovery (Laplante et al, 1995), and indeed most of the early tests targeted ores or prospective ores for which gravity recovery was an obvious match. As the test became more accepted, more and more samples returned a verdict that precluded the use of gravity recovery, or made it marginal. Typically, such ores are either copper-gold or base metal ores in which the GRG content is often fine (largely below 105 um) and ranges from 8 to 33%. Extensive simulation and plant sampling tests, either published (Laplante et al, 1997) or proprietary, show that full scale gravity recovery for these applications is generally below lo%, and can be as low as 2%. Not in all cases are such low recoveries economically unjustifiable, since there is documented evidence (Darnton et al, 1992) that a significant proportion of the gold recovered, at least in the case of base metal ores, would not have reported to the copper or zinc concentrate and received NSR credits."

Jan 1, 2002

By W. A. Scheuch

ORDINARILY secondary copper, unless electrolytically refined, is reclaimed directly as foundry ingots used in the manufacture of copper-rich alloy castings. This use does not require the elimination of the impurities to the degree required if the recovered metal is to be used for electrical purposes where a high electrical conductivity is of prime importance. However, as a part of the general policy of reusing its own scrap and by-products wherever possible, the Western Electric Co. at its Hawthorne Works is recovering its secondary copper as wire bars which are delivered to its own rod and wire mill and there processed into wire of high electrical conductivity. This departure from the usual recovery scheme has been accomplished through the careful classification and sorting of the material entering the furnace charges and the careful control of the subsequent melting and refining in a reverberatory furnace. Tests conducted over a period of approximately four years have shown that the quality of wire bars produced from selected secondary copper is equal to that of wire bars produced by the electrolytic refineries. The interest which has been exhibited in the process by those who have seen it has prompted the following general description. It is the authors' opinion that the recovery of secondary copper will become more and more an important factor in the copper production industry. The description is largely of the refining furnace and its operation, but it must be remembered that careful classification and sorting of the scrap materials to eliminate impurities are just as important as the furnace operation toward obtaining a satisfactory final product. Classification and sorting do not lend themselves easily to description; they must just be done. It should also be recognized at the outset that constant intelligent supervision is requisite to the success of the process because there are so many ways in which impurities can find their way into the final product.

Jan 1, 1929

By Arndt C. R

The Ispat Mexicana SA de CV (IMEXSA) pelletising plant is located at Lazaro Cardenas on the west coast of Mexico. It is the primary source of feed stock for the adjacent direct reduction (DR) plants and steelmaking facilities. The initial design of the pellet plant began in 1981 for 3 Mtpa of DR grade pellets using local concentrate received by pipeline.' Several construction delays, an ownership change, and a decision to use imported concentrates delivered in 60 000 to 90 000 tonnes ship cargoes required flowsheet modifications and additions. The design concepts are described for the plant which includes concentrate regrind to final pelletising particle size.

Jan 1, 1999

By J. A. de Carvalho Junior

This paper analyses the impact of the uncertainty associated with the input parameters in a mine planning optimization model. A real example was considered to aid in the building of a mathematical model that represents the coal production process with reference to the mining, processing, and marketing of coal. This model was optimized using the linear programming concept whereby the best solution was perturbed by the stochastic behaviuor of one of the main parameters involved in the production process. The analysis of the results obtained permitted an evaluation of the risk associated with the best solution due to the uncertainty in the input parameters.

Jan 1, 2012

By M. -C. Noël, G. P. Demopoulos

In this work the formation and environmental stabilization potential of arsenate-containing fluoroapatites is considered. In particular in this research various compounds were precipitated from synthetic solutions containing fluoride, arsenate/phosphate and calcium by varying different parameters-temperature, Ca:As ratio, pH, and P:As ratio, and aging time. The results obtained helped determine the operating window that should be used for the formation of highly crystalline fluoroapatites, in particular svabite (Ca5(AsO4)3F). It was found that svabite has a specific pH range of precipitation, with lower pH yielding CaF2 and calcium arsenate compounds such as CaHAsO4•H2O. At higher pH, a mixture of svabite and johnbaumite (Ca5(AsO4)3OH) precipitated, yielding a less stable material. This range of precipitation varied with the concentration of arsenic in the starting solution, and widened with higher initial concentrations of Ca2+, AsO4 3- and F-. Furthermore, svabite/fluoroapatite solid solutions were formed by using the same procedure as svabite but replacing some of the arsenate in solution by phosphate. The increase in phosphate content yielded a gradual change in morphology and crystallinity. Work on stability evaluation is currently under way.

Jan 1, 2014

By S. Solar, G. Tiess, K. Nielsen, H. Wagner

The paper summarises the results of a recent study of minerals planning policies of the Member States of the EU. The study has shown that contrary to the public opinion the production of industrial minerals and construction minerals is significant the former accounting for about 20 percent of global production, the latter amounting to about 3 billion tonnes per annum. In contrast the importance of metal ores has diminished although metal production in some European countries can still be significant. The study revealed that very few Member States have clearly defined mineral policies. Common to most mineral policies is the emphasis on reducing minerals consumption and recycling whereas the important aspect protecting access to minerals resources is not adequately addressed by most policies. Access to mineral deposits is regulated in most Member States by land use legislation and administration. Information on mineral deposits in land use planning data bases tends to be scarce. This together with the absence of formal mineral policies places minerals at a disadvantage in land use decision making. The emergence in the recent past of environmental legislation and in particular environmental impact assessments has had a crucial effect on the duration of the authorization process for new mineral projects. Examples are given how minerals planning is handled in some of the Member States.

Jan 1, 2005

By R. G. Cawthorn

The vertical distribution of platinum-group elements (PGE) in the Merensky and UG2 chromitite Reefs is highly variable, but does follow certain general patterns that allow the testing of geological models. In the Merensky reef, historically popular geological representations and interpretations have suggested that the mineralization occurs in a pegmatitic pyroxenite bounded by two chromitite layers. However, there are now enough published exceptions to this relationship to expose its fallacy. The vertical distribution of the PGE depends largely upon the separation between these two chromitite layers or the absence of one chromitite layer. Where separation is small or only one chromitite layer is present, there is considerable PGE mineralization in the footwall below the pyroxenite and lower chromitite layer. With increasing separation between the two chromitites, the mineral¬ization occurs progressively higher in the succession, and tends to track the upper chromitite layer. The view presented here is that the entire Merensky package is comprised of three events of magma emplacement, in which each has produced variable reaction with, and erosion of, the footwall, causing recrystallization of pyroxenite into pegmatitic pyroxenite. The magma then produced a chromitite layer followed by pyroxenite. Each chromitite layer is associated with some mineralization, which was extensively complemented by the subsequent formation of a sulphide liquid carrying PGE that trickled down through about 1 m of permeable crystal pile. The sulphide liquid formed after, not coincident with, the pyroxenite layers. The distribution of PGE in the UG2 chromitite shows up to three upward depletion sequences of PGE, also suggesting three events. The PGE are associated only with the chromite. The contribution from a sulphide liquid is considered to have been minimal for two reasons. Cu and Ni are extremely low in the UG2 which would not be expected if sulphides had been present. Also, by analogy with the Merensky, downward trickling of sulphides would have caused some PGE to be present in the footwall. There are some PGE in the footwall, but only where remnants of chromitite occur, and the hanging wall is lacking in PGE. In the northeastern Bushveld the UG2 chromitite is thinner than elsewhere, and there is a UG3 chromitite layer, not present elsewhere, that has a high Pt/Pd ratio. It is surmized that in the rest of the Bushveld the UG3 only appears to be absent because it has merged with the UG2 to produce the high Pt concentration at the top of the composite UG2. The non-accumulation of the package of pyroxenite-norite-anorthosite between the UG2 and UG3 in the northeastern Bushveld, which is not seen elsewhere, creates an interesting challenge to the formation of silicate layering in the complex. The mineralization in the Platreef is not addressed here. Keywords Bushveld complex, Merensky Reef, UG2 chromitite, geological evolution.

Jan 1, 2011

By Kathleen M. Kowalski

In emergency management, the effects of stress on the performance of emergency personnel, typically have been ignored or regarded as too enigmatic to quantify. This paper discusses the concept of Critical Incident Stress in responders to emergencies. It presents the rationale for considering stress as a significant factor in the management of emergencies. It is proposed that Critical Incident Stress Debriefing in a disaster can improve the effectiveness of response teams on site, their turnaround time on site, and post-disaster time off the job. Critical Incident Stress intervention also can mitigate potential deleterious emotional effects associated with emergency work. This paper, prepared by a U.S. Bureau of Mines researcher, offers some ideas to the mining industry in general, to mine rescue team trainers, and to developers of program simulations on the specific issue of how people, time, materials and space may be factored into a plan for emergency management. The impact of stress on emergency workers is, presented as a missing component in present emergency management models.

By R. Chen

Most tunnels built in Sydney encounter similar ground situations; they penetrate either the Hawkesbury Sandstone or the shales that lie beneath the city. Tunnels in these materials are generally sup-ported by rock bolts in combination with a shotcrete lining. A method of analysis is presented to improve our understanding of the long term behaviour of fiber reinforced shotcrete (FRS) materials and the tunnel support systems. A finite element method SAFEA (Semi-analytical FE Analysis) is developed to model the combined creep behaviour of a shotcrete lining and the Hawkesbury Sandstone. To model the time-dependent creep behaviour, the bulk modulus and shear modulus of the materials are represented by logarithmic functions in time. A Laplace transform is then applied to these functions of time and the solution of the problem found from a finite element analysis. Tablot?s method is then used to invert the transformed values and find the solution in real time. The time dependent creep deflection of the numerical tunnel models reflects the interaction of the shotcrete lining and rock which have different creep parameters.

Jan 1, 2008

By L. du Plessis

The name FISH (Fully Integrated Sort House) refers to a class of technology deployed at Jwaneng Mine final diamond recovery. The FISH concept is based on three pillars, namely: ?Improved sorting efficiency FISH is based on laser technology, which is more efficient than hand sorting for certain product categories. Laser sorting is based on measuring in-elastically scattered light from molecules and this is referred to as Raman spectroscopy. The Raman scattered light occurs at wavelengths that are shifted from the incident light by the energies of molecular vibrations ?Availability of production information Roller gap diamond size distribution information is generated on line for upstream process optimization ?Improved product security A ?hands-off? philosophy reduces security risk during operation and maintenance of the plant. In addition, a number of lessons were learnt about the application of new technologies in the industry: ?The required human competency profile demanded by new technology should match the available competencies of the operational staff ?An integrated information management system should be fully functional for both production management and diamond control purposes ?Operational feedback must be correctly evaluated to identify design, maintenance, training and operational issues so as to accelerate the maturity of the new technology within the time span of the sustainable operations project ?Project execution and technology maturity risks have to be evaluated and married to ensure risk mitigation by means of suitable project resource and contracting model selection.

Jan 1, 2003

By G. van Aswegen

The geometry and morphology of a set of low-angle fractures around a stope in a deep Witwatersrand gold mine are explained in terms of extension fractures forming under variable conditions of stress. Primary extension fractures (E1) form some distance ahead of an advancing stope along the s1, s2 plane. With stope advance, a couple of these fractures end up in a stress regime conducive to transpressional shear and a secondary set of extension fractures(E2) is formed at a high angle to the primary fractures. i.e. at a low angle to the stope. As the E2 fractures are undermined, they migrate into a stress regime of transtensional shear and a third set of extension fractures (E3) may develop between E2 fractures. These have sigmoidal shapes, being parallel to the E2 fractures at the E2 discontinuity where s3 is negative, and curved through the un-fractured rock between E2 fractures where s3 is positive at the instant of fracturing. The fractures all display fractographic features characteristic of dynamic extension failure with striae indicative of the direction of rupture propagation and the local, instantaneous orientation of s1.

Jan 1, 2012

By William Brundan

INTRODUCTION The Srisailam Left Bank Canal (SLBC) Tunnel Scheme is part of the Alimineti Madhava Reddy Project in Andhra Pradesh, South India. This scheme has been planned since 1983 and will provide irrigation facilities to drought-ridden areas in Andhra Pradesh. Water will be transferred from the Srisailam Reservoir during the monsoon months to 0.3 million acres of farmland and will also provide drinking water to villages en-route. The paper will address the design and onsite assembly of the Robbins Double Shield TBMs for Tunnel-1 of the SLBC tunnel scheme from planning to start-up of the machines. Also, it will provide a current status of the project and describe the advantages of a site assembly. Problems encountered to date and the solutions adopted will also be described. The project comprises over 50 km of tunnels and involves construction of the world?s longest tunnel without intermediate access. The TBM tunnels at 43.9 km in length and 10.0 m diameter will cross the Amrabad plateau, containing a wild life sanctuary and India?s largest tiger reserve, the Rajiv Gandhi. Jaiprakash elected to excavate the tunnel using two tunnel boring machines, rather than by drill and blast, in order to alleviate surface disturbances to environment and the tiger reserve, wild life sanctuary, and protected forestry areas. The Project was awarded to the Main Contractor Jaiprakash Associates Ltd with The Robbins Company as the Tunnel Boring Machine (TBM) supplier in August 2005. The Robbins Company supplied the TBMs along with two continuous conveyor systems and all spares and consumables to complete the tunnel excavation.

THOUGH the literature on the chamber process is considerable, it mostly refers to European conditions. Owing to the demand for acid for flotation and leaching at the mine, it may be necessary to work the process under other conditions. Consequently, some results obtained during the chlorination days at Mount Morgan, within the Tropic of Capricorn, may be useful for reference when working in a similar climate. Though the chambers must be protected against tropical storms, thorough ventilation should be provided, with plenty of space between the chambers, which are almost invariably crowded together. Not only does the space assist in the cooling of the chambers, but it is very desirable during repairs, when lead andtimber have to be hoisted up. The connecting flues between the chambers, which are fairly efficient mixers and condensers, should be round, supported from above, and with the least possible timber about them. Their position and arrangement deserve careful attention. Lattice work will be sufficient protection for the sides of the chambers, and the roof should be high and well ventilated. The Mount Morgan plant, crowded and not well situated, consisted of seven chambers (four over 50 ft. in length), one Glover tower 7 ft. 2 in sq. x 20 ft. high, one Gay Lussac 9 ft. sq. x 30 ft. higb, also one 5 ft. diam. x 25 ft. high. There was one pipe column 4: ft. sq. x 14 ft. 6 in. high. The chambers were run as one unit, and were much lower than those usually constructed in Europe-less than 15 ft. high. Provided that suitable timber can be obtained, 20 ft. is quite low enough. It should be quite satisfactory to use round poles for the studs, and so admit more air space between studs andlead.

Jan 1, 1920