Search Documents

By Chao Li, Qian Li, Yong-bin Yang, Kai Li, Qiang Xie, Yuan-yuan Zhu, Dong-ye Li, Qi-bing Tan

"The permeability of sintering mix is a vital technological property in sintering process. However, it can only be measured by off-line method on samples picked from the production. In order to acquire the properties of sintering mix accurately, on-line measuring of permeability is urgently required. Based on the reflection characteristics of bed permeability on pipe flowing parameters, a new method is presented in this paper for on-line measuring of sintering mix permeability. The measurement can be performed by blowing gas flow in the bed with the measuring pipe. Measuring results are obtained by picking the data on flowing rate and pressure in the pipe. The function of flowing rate to pressure may be certain for samples with the same permeability. Thus, the permeability was determined by contrasting this function to the result of off-line measuring, and the relative coefficient or R2 value was more than 99%.IntroductionThe permeability of sintering mix is a vital technological property in sintering process, which directly determines production and quality of sinter, or even determines whether the sinter production is carried out smoothly [1,3].The permeability have more obvious influence on vertical sintering speed, which is mainly related to air quantity passing through material bed. Under certain inducing capacity and negative pressure, the vertical sintering speed mainly depends on the permeability of sintering mix. Low permeability may make burning through point of sintering move back, and the sinter mix cannot be burnt through. High permeability may make burning through point of sintering move forward, improving production efficiency by increasing the speed of sintering machine [4] Good permeability means a small resistance of fan ,reduction of negative pressure of sintering machine, and full contact between air and sulfide, which can strengthen physical-chemical reaction during sintering process and increase desulphurization rate. In gas well through material layer process, gas-solid desulfurization reaction and gas-solid-liquid heat exchange are completed and hot gas through the combustion zone supplies the sintering process with heat. Finally uniform sintering of the material layer in height and width direction is achieved [5] While high permeability index leads to weak sinter strength, fast sintering speed, short residence time of high temperature region and little liquid phase. Moreover, liquid phase in the fast cooling process is too late to fully crystallize but forming glass phase which is harmful to sinter strength as well. Bad permeability means a big fan resistance and increase of negative pressure of sintering machine, which make the air pass through material layer difficultly. When air and mix contact difficultly, removal of sulfide reduces so that desulfurization is incomplete. Meanwhile, low caking efficiency, slow sintering speed and easily burnt sinter , reduce sinter output. Therefore appropriate permeability of sintering mix is the premise of stable burning through point and satisfactory sinter output and quality."

Jan 1, 2013

By E. Açma

Sivas-Divrigi flotation plant has a capacity of 90,000 tpy. Beneficiation of the tailings of iron ore magnetic separator seems to be attractive, because of its Cu, Co, and Ni contents. In the experimental work, sulfidic flotation concentrate is produced from these tailings. A roasting-leaching-H2S precipitation procedure is used to treat this concentrate, containing 0.55% Cu, 0.51% Co, 0.74% Ni, and 0.027% Zn. Sulfatizing roasting is carried out in a rotary furnace at 690°C. Roasted product is leached with 10 gpl HzSOl at 70°C and 30% pulp density. For the precipitation of desired metal, H2S is bubbled through the concentrated solution of repeated leaching, under controlled temperature and pH. Final metal recoveries of 91% Cu, 91% Co, and 50% Ni, and 92% Zn are attained. Roasting gases with their 13% SO2 content are suitable for H2SO4 production and the leach residues can be integrated with the iron ore processing plant as they contain 57.4% Fe and very low non-ferrous metals.

Jan 1, 1993

By K. J. Martchek

"This introductory presentation will highlight recent efforts to quantify the positive value of recycling metals such as aluminum, magnesium, lead, zinc, nickel and copper in relation to the three pillars of ""sustainable development"" - environmental protection, economic development and improve social consequences.This presentation will provide an overview of life cycle assessment profiles increasingly being utilized by customers, regulators and environmental advocacy groups to holistically evaluate the environmental performance of materials and products. The environmental profiles of prodi.lcts containing recycled metal will be presented based on rules established by the International Organization for Standardization (ISO).Significant to the life cycle profile of metal products is recent confirmation. that recycling has the potential to reduce materials production energy consumption by 95% for aluminum, 80""/o for magnesium and lead, 75% for zinc, and 70% for copper. Furthermore, . ""metals are eminently and repeatedly recyclable, while maintaining all their properties (1 ). "" Their durability relative to many hydrocarbon based materials enhance .their life cycle performance. However, the persistence of metals when dispersed into our natural environmental makes recovery and recycling particularly important Overall, when considering life cycle effects, recycling is critical to a sustainable future for metal products.Finally, regional and international regulations will be highlighted which will effect the efficient recovery and recycle of metals and their overall contribution to environinental protection, economic development and the enhancement of society."

Jan 1, 2000

By Chikabumi Yamauchi, Mitsuru Tanahashi, Toshiharu Fujisawa

"Thermodynamic properties of impurities in molten silicon are of prime importance in developing economical production methods of solar grade silicon. In the present research work, thermodynamic properties of boron, the most difficult element to remove from molten silicon, were measured by chemical equilibration techniques at 1723 and 1773 K. Activity coefficients and self-interaction parameters of boron in molten silicon were determined by equilibrating the melt with solid BN under controlled nitrogen partial pressures. Interaction parameters between boron and nitrogen in molten silicon were also determined by equilibrating the molten Si-B alloys with solid Si3N4• Based on the data obtained, the stability diagram of the Si-B-N system was established.IntroductionPhotovoltaic power generation using a silicon solar cell is expected to be the most promising energy source, because it is inexhaustible, cleaner and more safety than conventional energy sources, such as thermal or atomic power generation. At present, expensive off-grade silicon for semiconductor (SEG-Si) is used for a solar cell production. However, if a large-scale photovoltaic energy conversion using silicon solar cell comes into wide use in the near future, silicon will be sure to be in short supply for the cell. Therefore, a development of a new large scale process for solar grade silicon (SOG-Si) production is definitely necessary, which can remove contained impurities from silicon.Among the impurities contained in silicon, boron is one of the most difficult ones to remove by a zone melting or an unidirectional solidification, because its segregation coefficient in silicon is close to unity (0.8). In addition, boron behaves as a p-type silicon semiconductor dopant and, therefore, its content in SOG-Si must be severely controlled. Although some attempts to remove boron by various metallurgical methods have been carried out [I -4], quantitative analysis has not been made due to lack in the information on the thermodynamic properties of boron in molten silicon. From this view point, the activity of boron in molten silicon was determined in the present study by chemical equilibration techniques at 1723 and 1773 K."

Jan 1, 1998

By Bart Blanpain, Muxing Guo, Zhuangzhuang Liu

In order to stabilize free lime in the basic oxygen furnace (BOF) slag to achieve high value products, quartz sand and other additives are injected into slag. However, the current hot stage slag stabilization does not work in case of slag (before treatment) with a liquid fraction lower than 90%, where the slag containing solid particles is too viscous. Therefore, it is essential to understand how solid phases affect the viscosity of the slag system. In this study, the industrial BOF slags were investigated with respect to the correlation between volume fraction of solid phases and its viscosity. Slag viscosity was measured with a rotating type viscometer at temperatures below the liquidus. The volume fraction of solid phases was quantitatively calculated with FactSage. The Einstein-Roscoe equation was employed to predict the viscosity of BOF slag.

Jan 1, 2016

By R. Padilla

A thermogravimetric study has been conducted to follow the decomposition and volatilization of arsenic from enargite concentrate in nitrogen and slightly oxidizing atmospheres. Temperature has a large effect on the rate of volatilization of arsenic. Fractional volatilization of arsenic as high as 98% were obtained in less than 60 min at 650°C in nitrogen atmosphere, while in slightly oxidizing atmosphere the same volatilization could be achieved in 30 min. It was found that arsenic volatilizes as sulfide in nitrogen atmosphere and as 4xture of sulfide and oxide in atmospheres containing 1% oxygen. By using the pore blocking and the first order kinetic models, apparent activation energies of 213 and 200 kJ/mol for the temperature range of 780 - 900 K and 205 and 184 kJ/mol for the temperature range of 900 - 985 K were determined for enargite and copper concentrate, respectively.

Jan 1, 1997

By Liu Wei-feng

Base on the thermodynamic calculation of vapor pressure of lead, antimony and arsenic at high temperature, the possibility of separating lead, antimony and arsenic in different temperature was analyzed ,and the practice of producing qualified antimony white from lead-antimony alloy by direct blowing was introduced in detail in this paper. The blast furnace reduction smelting was brief introduced firstly, and then alkaline refining was applied to removing arsenic from lead-antimony alloy that contains As1%,Sb39%,Pb58%,the arsenic in the treated lead-antimony alloy could decrease to 0.009% by that method. The antimony white containing Sb2O3 99.5% could be produced by air blowing in the special furnace at 650? from the treated lead-antimony alloy. And the electrolytic lead could be achieved by electrolysis from the lead-rich alloy which contained 83% lead.With high-grade product being obtained the process was shortened. The technology has been applied successfully many years in Guangxi, China.

Jan 1, 2009

By Shekhar Bhansali, Shyam Aravamudhan

"This paper reports on the design and simulation results of a silicon bulk-micromachined diaphragm-type piezoresistive pressure sensor capable of operating linearly over a wide dynamic range (0-1000 meters of water). The piezoresistor elements of the sensor are arranged in a wheat stone bridge configuration to achieve a higher output response. Simulation results (output voltage and sensitivity analysis) obtained using coupled MemPZR-MemMech module of the CoventorWare2003 Finite Element tool are presented. The effect of diaphragm size, diaphragm thickness and thickness of the piezos on output sensitivity were analyzed and optimized to get a linear response over the wide dynamic range.IntroductionThe physical and biological processes in the ocean are critically influenced by ocean parameters (pressure, salinity and temperature). Thus there is a need to develop inexpensive and reliable sensors to continuously measure large volumes of sea-space over long time spans. A key component in any such system will be a pressure/depth sensor. This sensor is routinely employed in marine applications such as wave and tide gauges, tsunami detection, platform leveling etc. More significantly, pressure measurement is needed for depth determination. Depth sensors are vital for remote operated vehicles (ROVs), profiling instruments and towed arrays.Several techniques have been routinely used in the past to measure pressure in the marine environment [1-3]. In general, the pressure sensor design is based on a flexible membrane as the spring element for the sensing pressure [4]. The deflection of the membrane, induced by the applied pressure, is converted into an electrical output through a component that is sensitive to diaphragm deflection (capacitive coupling) or associated stresses (piezoresistors, strain gauges). The temperature compensated pressure measurement can be readily converted to depth using"

Jan 1, 2004

By J. van Driel

NOx is a growing concern for acid plant operators due to recent legislation reducing the allowable stack limits, as well as continually more stringent requirements for product acid quality. NOx also causes a major problem during maintenance as NOx rich acid residues fume following exposure to moisture in the air. Until recently, the solution for NOx related issues was to treat the symptom, rather than the cause. NOx in product acid was treated using chemicals and the NOx in the plant stack was generally left untreated. As part of an environmentally driven change in concentrates, Budel Zink installed the first gas phase NOx destruction process to be incorporated into a commercial scale acid plant. Nitrogen oxides contained in the process gas are reduced selectively with ammonia over a catalyst to form nitrogen and water. As a result, the NOx reduction is in agreement with the permit requirements.

Jan 1, 2002

By J. B. Vander Sande, I. G. Solórzano, B. S. You, P. M. Jardim, W. W. Park

"Alloys with six different compositions in the system Mg-Ca-Zn were produced by melt spinning. The aging behavior of alloys was investigated by measuring the changes in microhardness after isochronal aging and the microstructure was analyzed by means of transmission electron microscopy (TEM), energy dispersive X-ray spectrometry (EDS), scanning transmission electron microscopy (STEM) and scanning electron microscopy (SEM). All six compositions in the as-solidified condition show a difference in microstructure between the wheel contact side (zone A) and the free surface side (zone B) as a result of the differences in the solidification rate across the ribbons. One of the alloys (Mg-l.5wt%Ca-6wt%Zn) was chosen to be more deeply investigated in this work as it exhibited grain boundary films and an age hardening behavior was produced in that alloy.IntroductionMagnesium is the lightest of all the commonly used metals, and very attractive for applications in transportation. It also has a number of other desirable features, including good ductility, better damping characteristics than aluminum, and excellent castability. However, there are some negative features, such as high reactivity in the molten state, inferior fatigue and creep resistance as compared to aluminum, poor corrosion resistance and high production cost.In recent years there has been a significant increase in magnesium use as a structural material. These structural applications include aerospace, automotive and nuclear industries as well as appliances and sporting goods (1 ). According to reports on Mg-Zn alloys, the addition of Zn (2) in magnesium increased strength. Also, since the maximum solubility of Zn in magnesium is 6.2wt%, a considerable amount of Zn can be retained in solid solution in magnesium alloys by rapid solidification. In addition, Ca is known (3) to be one of the most potent alloying elements for refining the microstructure and precipitates in magnesium alloys, and also to improve mechanical strength and corrosion resistance."

Jan 1, 2000

By R. G. Reddy

To better understand the behavior of bacterial-mineral interfacial reactions, a thermodynamic model based on the- studies of bacteria adhesion on mineral surfaces has been evaluated. The bacteria adhesion to the mineral surface would be increased by l ' d1;1creasing the change in Gibbs free energy of adhesion and it would be reduced if the change in Gibbs free energy of adhesion of the system is increased. From the combination -of Young's equation and equation of state, the change in Gibbs free energy of adhesion -for bacterium-mineral system- was calculated. Influence of liquid surface tension, mineral surface tension on the change in Gibbs free energy of adhesion and consequently bacteria behavior on mineral systems- has been discussed.

Jan 1, 1991

By Chonghun Han, Tae-Hwa Choi, Young-Hwan Chu

"A statistical optimization method is proposed to maintain stable operation in a blast furnace with stave coolers. The objective of this study is to find the operating condition which maximizes productivity as well as minimizes the heat load on the stave coolers. In this method, we first analyzed historical data and calculated the heat flux of stave coolers and the burden distribution by mathematical models. In this approach, we determined the variables to optimize and manipulated variables to adjust these response variables. Next, we collected the necessary data for the data variables after preprocessing such as removal of noise and outlier. Finally, we constructed empirical models describing the patterns of response variables in terms of manipulated variables by partial least squares regression method, and then these models were used as objective functions for entire optimization problem. By using appropriate optimization algorithm, we determined the compromised optimum operating condition considering all response variables from the past operating conditions.IntroductionBlast furnace operation which is accompanied by complex physical and chemical phenomena is an essential process for steel industry. In this process, iron ore which is charged into the blast furnace from the top goes downward. It is reduced to iron by CO gas and is melted by the heat of combustion of coke and pulverized coal. The pig iron is tapped at the bottom in liquid phase after removing the slag, which floats on the pig iron.The cooling equipment of the blast furnace wall is changed from the plate type to the stave cooler recently. In order to cool the shell uniformly and eliminate shell spray cooling, Pohang No.2 blast furnace of POSCO (Pohang Iron & Steel Company) was equipped with 11 rows of stave coolers. These staves are only 350mm-thick including the 170 mm-deep refractory on the hot face."

Jan 1, 2001

By Jiangwei Shen, Cong Wang, Haibin Zuo

The research on the formation of Silico-Ferrite of Calcium and Aluminium (SFCA) in the process of cooling and solidification is rarely reported. The crystallization process was observed by using scanning electron microscopy (SEM) and optical microscope in this paper. The effect of different cooling system on the microstructure and phase composition of the sinters was investigated to obtain the appropriate cooling rate to improve the metallurgical properties of sinters. The experimental results show that the crystallization of calcium ferrite is getting better when the cooling rate is decreased from water quenching to cooling in the air. There are a large number of hematite phases with interconnected crystal structure in the sample cooled in the air. In the case of the compressive strength, it was determined by the mineral composition and pore structure, higher SFCA and hematite contents in sinter cooling in the air lead to a higher strength. Glass phase in the water quenching sinter was the major reason for the lowest strength. High porosity contributes to a decrease in compressive strength for the sinter cooling in the furnace. Therefore the air cooling was the appropriate cooling rate to achieve high quality sinter under this experimental condition.

Jan 1, 2016

By Carla Lupi

Zinc electrowinning from sulfate solutions is the traditional industrial method to produce SHG zinc. Over the past few years several efforts have been done to improve process efficiency in order to reach high productivity with low energy requirement. The latter aim can be pursued both by means of a hard purification of the electrolyte and reducing the anodic voltage. This work is a comparative study of the results obtained in several previous researches on zinc electrowinning from both sulfate and chloride solutions. Zinc electrowinning tests on industrial sulfate solution have been carried out by using Pb alloy anodes and by adding organic depolarizers such as ethanol, acetic acid or ethylene glycol. Experiments on chloride solutions, obtained by purification of zinc exhausted electrolyte, have been performed by using DSA anodes and by testing the effect of additives such as TEACI and TBAC\. Comparing the best results obtained with the two methods it can be highlighted that a high quality zinc is electrowon in both cases with comparable energy requirements.

Jan 1, 2000

By Nelson Collao I.

Loss of the organic phase from solvent extraction circuits is a major cost factor for SXEW operations. Recognized sources of loss include evaporation, entrainment, and biological degradation. The mechanisms for both entrainment and evaporative losses are well recognized. Biological degradation of the organic has not been as extensively evaluated as the other mechanisms but is a major source of loss. This paper discusses the impact of biological degradation on an operating plant, potential mechanisms for degradation, conditions under which biodegradation of plant organic can occur and plant conditions that may assist in promoting biodegradation.

Jan 1, 2003

By J. W. Matousek

Copper losses in smelter slags are :typically normalized with some form of the distribution coefficient, written as the ratio of the weight percent assays of metal in slag to the metal in matte or its inverse: L(s/m) = %(Cu)/%[Cu] or L(m/s) = %[Cu]/%(Cu) However, this simple approach ignores the dynamics of the smelting process. It overlooks the effect of the chemical work done in producing a given matte grade from concentrates of different grades -- or from a single concentrate blended with varying quantities of copper bearing precipitates or reverts. This paper examines the combined influences of matte grade and the work done in smelting on the copper content of smelting furnace slags. A simple model for the relationship is proposed.

Jan 1, 1999

By M. M. Swan

A stratiform gold occurrence of Precambrian age located 20 miles southeast of Prescott, Arizona, within the Agua Fria Mining District, displays chemical, mineralogical, structural and lithological patterns indicative of a distal, exhalative volcanogenic environment. Metavolcanic and metasedimentary rocks of the Proterozoic Yavapai Series (1775-1820 m.y.) host the mineralization and are'characterized by greenschist grade metamorphism, steeply-plunging penetrative folds and steeply-dipping schistosity. Mineralization is confined to a 100m thick stratigraphic section that is comprised of a series of thin auriferous massive sulfide beds and intercalated schist .containing disseminated sulfides. The mineralization extends more than 4km along strike. Coincident with, and largely confined to the mineralized strata, are anomalous amounts of As, Sb, Cu, Pb, Zn and Ag and associated silicification, sericitization and carbonatization. This exhalative mineralized system is interpreted to have been deposited in a paleo topographic low on the distal flank of a submarine rhyolite dome and to represent the final episode of a Precambrian volcanic cycle.

Jan 1, 1981

By Varadajan Seshadri

Kambara Reactor (KR) consists of a ladle where pig iron is stirred by an impeller during addition of a flux powder. The objective is to improve agitation leading to dispersion, of the flux powder, in the molten pig iron in order to improve desulfurization of the liquid melt by improving solid liquid interaction. The life of the impeller is limited as it is subjected to abrasion at high temperatures. The shape and design of the impeller also has an effect on the performance of this reactor. A 1:7 scale cold model of a KR unit of the Companhia Siderurgica de Tuberao ,one of the integrated steel plants in Brazil was constructed in order to evaluate the mixing and mass transfer conditions. Mixing efficiency was investigated by tracer additions and subsequent measurement of conductivity. Mass transfer in the reactor was assessed through iodine transfer between water and kerosene and employing a macroscopic model. Mixing depends on impeller shape and depth of immersion The role of dispersion is highlighted by faster kinetics when impeller velocity is increased. The results enable assessment of design aspects of the impeller on the process.

Jan 1, 2006

By Wenying Liu

The effect of aeration on chalcocite heap leaching was studied by analyzing the historical data from two chalcocite heap leach pads located in Chile, one with aeration and the other without aeration. The data showed that the copper leaching kinetics of the aerated heap was greater than that of the unaerated heap within a certain leaching period, after which there was no effect of aeration on the copper leaching kinetics. The total acid consumption per ton of ore processed was higher in the case of aeration, which was supported by the higher pH of the PLS. But the net acid consumption per ton of copper produced was the same in the two cases. Approximately 5% of the total iron added to the unaerated heap was precipitated inside the heap. In contrast, there was no net iron precipitation or generation inside the aerated heap. Bacteria activities were thought to occur even in the unaerated heap, but the extent was much less than in the aerated heap. Given the importance of forced aeration in chalcocite heap bioleaching, mathematical modelling will be applied in the future work to assist the optimization of the aeration system design.

By Shengqin Zhang, Yousef Mohassab, Feng Chen, Hong Yong Sohn, Mohamed Elzohiery, Amr Abdelghany

The kinetics of hematite concentrate reduction by mixtures of hydrogen and CO of various compositions has been investigated as part of the development of a flash ironmaking process at the University of Utah. This process produces iron directly from iron oxides concentrates by the gas-solid flash reaction based on the partial oxidation of natural gas, resulting in a significant reduction in energy consumption and greenhouse gas emission. The reduction kinetics of hematite concentrate of an average particle size 21.3 μm by the above mentioned gases in the temperature range 1423 to 1623 K (1150 to 1350 ºC) was investigated. Hematite concentrate particles can be reduced to > 90% by any of these reductants in several seconds of residence time typically available in a flash reactor. The activation energy ranged from 214 kJ/mol for hydrogen to 231 kJ/mol for CO.

Jan 1, 2016