Search Documents

By A. Karami

It is well established that an ordered sequencing of charge initiations in a blast pattern is an important design consideration that affects blasting performance. Delay times must be chosen such that damage to the rock mass is controlled. The accuracy of delay detonators is also of major concern. A large scatter could lead to an incorrect blast sequencing that would lead to damage to the rock mass causing increased over-break, degraded fragmentation, increased fly-rock and poor vibration control. In this study, the effect of using accurate delay detonators on the explosive energy generated is investigated. For this purpose, power spectral density of the blast vibration for delayed shots are calculated and compared with the case where holes are shot at the same time (no delay). At the end the results are presented and discussed.

Jan 1, 2000

By Harry Sutcliffe

THE PROBLEM Two and a half years have gone by since the December, 1976 Civil Engineering article on subway costs caused such a furore. What has happened in this interval? Even after discounting the crushing inflation rate, costs are still increasing, and there is no sign of a turndown, even in the rate of increase. Some steps outlined in the article have been taken. In April this year, the first D.O.T.-sponsored Peer Review Group, made up of managers of other transit properties, met in Boston to review MBTA's $500 million Red Line Extension-Northwest for cost effectiveness. While the impact of a review at the end of the design phase, with substantial segments under contract, cannot be as effective as a review early in the design phase, it is nevertheless a start. This first meeting will be followed by a review of Boston's Orange Line relocation, the final design for which is just underway. In the industry at large two facts are evident: 1. We are failing to reduce underground construction costs. 2. Underground construction is in danger of pricing itself out of the market place. It has always been a greater challenge to design a Chevvy than to design a Cadillac, but it is the Chevvy we need today. Much attention has been focussed in the past on engineering design in the narrow sense: areas such as ground loading conditions and concrete design. This paper will attempt to make the case that costs in urban underground construction are primarily outside the area of structural

Jan 1, 1979

By SAHENDRA SINGH, SANJIT KUMAR PAL, DHARMITA HORO

The North Singhbhum Mobile Belt (NSMB) lies between two crustal-scale shear zones, the South Purulia Shear Zone (SPSZ) at the north, and the Singhbhum Shear Zone (SSZ) at the south. The Babaikundi-Birgaon Axis (BBA) is an east-west trending secondary shear zone in the NSMB lying south of SPSZ, which is known for the occurrence of gold along with other sulfide minerals within the quartz reefs. The present study has been carried out at north of Ichadih village, which lies on the BBA. The present study attempts combined electrical resistivity tomography (ERT) and self-potential methods along a profile of 470-m length in the Ichadih area to map the potential mineralized zones. Initially, ERT sections generated by Wenner, Wenner- Schlumberger, dipole-dipole, and joint inversion of the combined array have been analyzed, and results are validated through the analysis of model resolution. A prominent low resistivity (10–100 Ωm) associated with quartz reef/limonitic quartz reef at a depth of approximately 30–85 m, encircled by a high resistive (more than 10,000 Ωm) formation associated with metasedimentary rock, has been delineated using joint inversion of the combined array. Further, analysis of self-potential (SP) anomaly using particle swarm optimization inversion also confirms the prominent low SP anomaly at a depth of 77.3 m, which is analogous to the low resistivity anomaly identified in the joint inversion of the combined geo-electric array. Subsequent analysis of a complex synthetic geo-electrical model analogous to the present field situation proves the efficacy of the joint inversion of combined arrays. As a whole, joint inversion of multi-array data is established as an efficient technique for better subsurface imaging in case of the complex subsurface structure. In-depth analyses confirm the possibility of sulfide mineral-rich deposit (quartz reef/limonitic quartz reef) which requires further geological drilling and lithogeochemical sample analysis, for possible future exploration.

Oct 26, 2020

By E. R. Spencer

An assessment of U.S. western hard-rock miners? noise exposures was conducted as part of a multi-year National Institute for Occupational Safety and Health (NIOSH) survey of noise exposures in each sector of the mining industry. Noise from selected mining equipment and operator noise exposures were measured, analyzed, and tabulated for dissemination to the participating sites and are being used to direct NIOSH research and interventions to address the greatest noise hazards. Eighty-two noise dosimeter measurements were obtained, along with time-motion studies as the miners operated hard-rock mining machines. Ninety-six percent of the operators had daily noise doses that exceeded the Mine Safety and Health Administration?s permissible exposure level. The average gold miner dosages while operating the following equipment were: haul trucks - 261%, load-haul-dumps (LHDs) - 235%, single boom drills - 221%, bolters - 214%, and dual boom drills - 163%. The worst exposure level was a silver miner with a daily dose of 873%. Time-motion data showed that this miner?s exposure accumulated most rapidly while operating a jack-leg drill. These results will be used to help prioritize noise control development by NIOSH and other partners. Disclaimer: The findings and conclusions in this report have not been formally disseminated by the National Institute for Occupational Safety and Health and should not be construed to represent any agency determination or policy.

Jan 1, 2009

By R. J. Baumgartner

Sustainability issues are from rising interest and importance for the mineral industry worldwide. In order to bring them into management processes and to improve decision processes, economic, ecological and social aspects of products, services or technologies have to be assessed. In this paper, the concept of integrated sustainability assessment is presented. Each aspect is assessed with quantitative or qualitative methods. The results of these ecological, social and economic sub-assessments are integrated by the means of Fuzzy Logic in order to regard preferences of decision maker and circumstances of decision situation. An example demonstrates the application of this new instrument.

Jan 1, 2005

By A. G. Yapo, T. W. Camm

"All-in sustaining cost is a metric used by mining companies to reflect the cost of gold mining in a consistent format useful to both investors and mining professionals. Cost reporting focused on the direct cost of mining and processing ore was summarized in the non-GAAP cash cost developed by the Gold Institute in 1996. In 2013, a group of mining companies, working with the World Gold Council, developed a more inclusive approach to reporting costs designed to solve the dilemma of showing a more comprehensive reflection of recurring costs involved in producing gold, without discouraging investors. INTRODUCTION Mining today plays a key role in the development of our civilization as a source of essential raw material and provider of essential fuels, producer of jobs, and a factor in support of the international balance of monetary payment (Camm, 2014). Professionals in mining locate, develop, design and manage ore deposits in an environmentally safe and profitable manner. As mineral deposits become increasingly scarce, new challenges face the industry. A current trend is to an increased emphasis on underground mining techniques for deeper deposits. Operations are safer today than before as companies understand better their work environment and the importance of mining responsibly. A continual challenge for the industry is accurately reflecting the costs and selling price of ore. An enduring characteristic of mining is the situation where the market typically determines the price of a commodity; the main control a company has on the bottom line is to control the cost of production. An attempt to bring light and clarity on the cost of their business will give a better idea to investors on the true profitability of the mining business. Gold producers face this struggle to accurately reflect the cost of production while also seeking to attract the interest of the investment community (Hill, 2013). In order to have a consistent format to report on their production costs, leading gold producers through their alliance inside the World Gold Council (WGC), worked on the adoption of a new cost framework: the All-in Sustaining Cost (AISC) and All-in Cost (AIC). Since 1996, the traditional cash cost reporting has focused only on the mining and processing costs incurred in mining an ounce of gold, which included the costs of goods sold (labor, energy, and consumables costs) and royalties (Table 1). But cash cost reporting ignores many important aspects, like sustaining capital, general and administrative expenses, and site rehabilitation at the end of the mine life (Whelan, 2013). The cash cost was used to attract many investors into the business. In fact the high gross margin (sales minus cash costs) has been promoted the past decades by the industry instead of the net or operating margin. As a result, even when the gold price was high, nearly $1900 per ounce in August 2011, gold producers were not reporting excessive profits in their cash flow / income statements, to the disappointment and incomprehension of investors (Milstead, 2014). The truth was simply that the other costs omitted in the traditional cash cost were reducing the apparent profits."

Jan 1, 2017

By Drummond Earley III

The U.S. Bureau of Mines is currently conducting laboratory experiments to study the reactions occurring during in situ leaching of oxide copper ores hosted by biotite-poor granite and biotite-rich granite porphyry. Detailed pre-leach and post-leach petrographic examinations of the rock samples are combined with the leach solution chemistry resulting from core leaching experiments to enable an evaluation of the various reactions which are responsible for the observed fluid chemistry. The information resulting from these laboratory studies is being utilized to support the design of the Bureau's ongoing field research project at the Santa Cruz deposit near Casa Grande, AZ. Atacamite and chrysocolla are the primary copper minerals present in this deposit, and both are readily soluble in the dilute 5% sulfuric acid solutions used in these experiments. In addition to the dissolution of copper minerals, biotite dissolution also occurs during the experiments, contributing K, Mg, Fe, and Al to the leach solution. The biotite dissolution appears to be non-stoichiometric, as it is progressively altered to vermiculite and finally, amorphous silica. While K, Mg, and Fe concentrations in solution steadily increase with time, Al quickly reaches a maximum, and then remains relatively constant for the remainder of the experiment. This suggests that Al saturation is achieved, and this Is supported by the presence of precipitated Al sulfate and aluminosillcate clay mineralization in the post-leach rock samples.

Jan 1, 1990

By Tom Gonzales

At San Manuel, AZ, Magma Metals Co. operates an Outokumpu flash furnace, four Peirce-Smith converters and two anode casting wheels that are supported by six anode vessels. Process gasses from the flash furnace and converters are treated in a two-train/ double-contact sulfuric acid plant. The plant captures 98% of the sulfur. A new flash furnace was commissioned in July 1988. It has since processed more than 2.7 Mt (3 million st) of sulfide concentrate without a major rebuild. The company has gained unique experience in the operation of the flash furnace at high oxygen enrichments with low off-gas dust loadings. New procedures have been developed to maintain secondary material generation at equilibrium and for maintaining metallurgical control of operating parameters. Process flow description At Magma's San Manuel plant, concentrates and other copper-bearing material are blended and conveyed from two separate areas of the plant to three 420 t (465 st) capacity wet charge bins located above the rotary dryer. Flash furnace silica flux is conveyed to a 227-t (250-st) capacity fine flux bin located adjacent to the wet charge bins. The concentrate and flux are blended in controlled amounts and fed into a 168-t/ h (185-stph) gas-fired rotary dryer. The wet charge enters the dryer at 8% moisture and is dried to 0.2% moisture. The dried charge is pneumatically conveyed to a 580-t/h (640-stph) dry charge bin located above the flash furnace. Flash furnace charge is drawn from the bin by two drag conveyors at a concentrate feed rate of 145 t/h (160 stph). The charge is mixed with enriched combustion air and injected into the furnace reaction shaft. In the reaction shaft, the charge is oxidized to form matte, slag and a rich SO, off-gas.

Jan 1, 1992

By N. B. Pundari

Proper selection of large walking draglines, based on sound engineering principles and field experience, has not kept pace with the large capital expenditures needed to buy these stripping machines. The use of large walking draglines for stripping overburden in US surface coal mines grows steadily, but equipment selection continues to pose problems. An improper size, model, make, or spoil reach selected for a particular stripping application results in additional, unnecessary coal production costs. Large walking draglines are being used to dig deeper tar sands at the Syncrude operations near Fort McMurray in Northern Alberta, Canada. This application is compared with typical deep digging operations and dragline use prevalent at typical US strip mines.

Jan 4, 1981

By Claus Becker

The new, 2.600 m long pipe under the river Elbe in Hamburg/Germany required for 2 traffic lanes, emergency lane and space for utilities a boring diameter of 14,20 m(46,6 ft). According the geology (glacial deposits consisting of clay, sand and marl, all containing big boulders) a Slurry-Shield with crusher was selected. With a minimum cover of 7 m and a maximum pressure of 5,6 bar extensive ground treatment was necessary to make the drive feasible. The machine contains a lot of new developments. The drive was finished in spring 2000 so all experiences can be reported. A special risk sharing contract avoided completely litigation.

Jan 1, 2001

By Paul D. Tomlingson

Part two of this two-part series covers the use of an integrated information system with administrative information, including error and absentee reports as well as open work files. Part one (ME, July, page 650) discussed conceptualizing and developing a maintenance information system. It explained what information is needed to manage such a system.

Jan 8, 1985

Phelps Dodge Mining’s Bagdad, AZ copper facility uses a large series of cone crushers and ball mills to reduce copper ore to very fine particles. The solids are mixed with water to create a slurry. Milk of lime is added to this slurry to raise the pH. Small amounts of reagents are also added, including a frother to make bubbles, as well as a collector chemical that causes the copper minerals to stick to those bubbles. This material is pumped to a series of froth flotation cells to concentrate the copper. Air is blown into the flotation cell tank and the pulp mixture is vigorously agitated. Rising bubbles carry the copper particles over the edge of the flotation tank. The bubbles break after they flow over the edge.

Jan 1, 2005

By J. L. Page, A. C. Marlowe

The Research and Development Services of South Africa has begun underground trials with a Robbins 52RE blindhole borer using a cutterhead fitted with high pressure water jets to assist mechanical cutting. The objectives of the work are to reduce cutter costs by increasing cutter life and to increase overall penetration rates. The paper reviews blindhole boring in South Africa and laboratory experiments in rock cutting assisted with high pressure water jets. The borer and its ancillary equipment are described. Initial results of underground boring experiments are presented. The paper concludes with the test programme for the future.

Jan 1, 1985

By D. Dodgen, L. Larrimore

Electric utilities depend heavily on coal as a major fuel source for power generation, annually producing more than 85 million tom of ash, boiler slag and FGD (flue gas desulfurization - "scrubber") materials as by-products. Utilities and others who bum coal have traditionally disposed of these by-products in ponds or landfills. However, in the last 10-15 years there has been a greatly increased emphasis on beneficial utilization of these materials by the producers themselves as well as by customers who purchase the by-products. Regulatory, cost and technical performance issues currently impact the use of coal ash and other coal combustion by-products (CCB).

Feb 24, 1997

By Kazuo Magata, Hirohiko Fujita, Masazumi Tashiro, Yoshiaki Sato, Yoshio Shinoda

The Shinkansen of the Japanese National Railways (JNR) presently in operation between Tokyo and Hakata, approximately 1,000 km, was constructed at three stages: between Tokyo and Shin-Osaka opening in 1964, Shin-Osaka and Okayama in 1972 and Okayama and Hakata in 1975. Works on the extension of 400 km from Okayama to Hakata were launched in March 1970. As construction of the undersea Shin-Kanmon Tunnel on the extension was the toughest task, requiring many, many months, the work was undertaken earlier than any other works on the extension. It was brought to its completion in June 1974 at the cost of about 22, 000 million yen. The Shin-Kanmon Tunnel is the third undersea tunnel constructed to connect the main island of Honshu and Kyushu across the Kanmon Straits. (Table 1)

Jan 1, 1976

By F. Mielli

Mine operation managers are constantly tasked with identifying new ways to produce more, while using less. Mine effectiveness and reliability is the foundation of improving operational performance. Timely decisions need to be made in order to identify production waste. Intelligent data needs to be visualized in real-time. Operational events need to be captured with impacts quantified and root causes identified. Unfortunately, complex information technology solutions often have a very poor success rate, with some reports suggesting 30 percent of complex projects are canceled before completion.

Feb 27, 2013

Caterpillar’s 797 327-t (360-st) mining truck is currently being tested at the company’s proving facilities. Mine evaluations began in the second quarter. The unit will be commerically available in North America in 2000 and worldwide in 2001. The new model is the largest of Caterpillar’s off high-way truck line. In addition, the company has replaced its 966F series II and 970 F wheel loaders with the966G and 972G models. 797 mining haul truck Caterpillar developed the 797 mining haul truck in response to mining companies seeking to reduce cost per ton in large-scale operations. The 797 is sized to work with loading shovels used in large mining operations. And Caterpillar will match the body design to the material being hauled, to optimize pay-loads.

Jan 1, 1999

By T. A. E. Breen

A new high intensity grinding technology has been developed and is now being commercialized by Hicom International of Australia. This has led to the development and manufacture of Hicom 120 grinding mills which are now being sold internationally for a range of mining industry applications. The first commercial process application has been for the diamond sector, where the ability of the mill to remove host kimberlite rock by attritioning, with no damage to the thereby liberated diamonds, is seen to be a most beneficial attribute. There are, however, many other mineral industry applications for this mill. The design of the Hicom mill is unique. Based on a high speed centrifugal motion of the grinding chamber, very high power intensity is delivered to the grinding process. Most significantly, a high acceleration field, 50 times stronger than gravity is produced, creating very high power input per unit of mill volume, and exceptionally fast particle breakage rates, typically 50 - 100 times greater than those in conventional tumbling mills. A mill developing such forces has significant implications to comminution technology and practice.

Jan 1, 1999

By S. K. Oraee

Most management decisions at all levels of the organization are as directly or indirectly depends on the circumstance of future. With regard to predict the future events in the process of decision-making plays a main role, therefore, forecasting is very important for every organizations and institutions. There is a variety of methods to predict time series. In general, these techniques can be divided as following: statistical, artificial intelligence and analytical techniques. Two of the most common methods for time series prediction is autoregressive integrated moving average (ARIMA) and artificial neural network (ANN) methods, these methods are the subset of statistical and artificial intelligence techniques respectively. In this paper, a hybrid model of ARIMA and ANN models are employed to predict the number of fatal injuries in the USA underground coal mines. This research showed the result of hybrid model is better than split model.

Jan 1, 2011

By J. J. Snodgrass

Faults, sandstone channels, and abandoned mine workings present severe safety hazards, disrupt mining, and necessitate costly precautions or discontinuance of operations. In addition to fault detection, mining companies have a need to map discontinuities such as seam thinning and previously mined areas in both longwall and room-and-pillar operations. Initial field tests demonstrated successful generation and propagation of higher order guided wave modes. Theoretical studies indicate potential for improved resolution by sensing small details in the coal seam and roof structure. Controlled-waveform source transducers and specialized detectors are particularly useful to preferentially excite and detect the Love (SH) and Rayleigh-type (P-SV) waves, including the higher frequency modes. The distinct observation of reflections using the transducers in the shear wave mode makes feasible the detection of the water-filled voids.

Jan 4, 1985