Search Documents
Search Again
Search Again
Refine Search
Refine Search
-
A New Bubble Pick-Up Technique as a Rapid Flotation Test Method
By A. F. Lee
Dr E. C. Hanekom (Visitor): Two years ago we used the bubble pick-up technique as developed at Anglo American Corporation for screening candidate flotation agents prepared in our laboratories. It was obviously necessary to know to what extent the technique gave reproducible results and a statistical evaluation of the test method was made using a mineral sample provided by Anglo American Corporation. A bubble of 2.0 mm diameter was used and the measuring graticule was divided into squares (units) with sides of 5.0 mm at 25 X magnification. The mineral granules had diameters from 53 to 74 mm. The bubble was loaded by depressing it against a layer of mineral grains to give an arbitrary but constant compression of 0.4-0.5 mm. It was rolled five times through 2 mm horizontal displacement. The bubble was then lifted, its load compacted by gently stirring and the projected area measured in squares (units) on the grid. Each substance was tested at 5 ppm concentration in distilled water at five points in the pH range 3-6. With these standardized conditions of operation the reproducibility of the test was studied. Four materials were tested and at each pH value the procedure of forming a bubble, picking up granules and counting the units was repeated ten times. From these results the standard deviation for a single count at any pH value was calculated for each material (Table 1. The coefficient of variation of approximately 3 per cent was relatively low and it was decided that further refinements in the counting procedure would be of doubtful benefit with the present apparatus. Similar experiments were carried out with 12 sample materials. In this case the bubble formation and pick-up were repeated four times at each pH value, the mean value was calculated for each set of four observations and final pick-up values for the materials were obtained by selecting the highest mean count. Each test was completely repeated a number of times as indicated in Table 2 and the standard deviation calculated. The results allowed the selection of the more promising materials and the rejection of poor performers at the 95 per cent confidence level. All tests were carried out by one operator. Some evidence was obtained that the method is sensitive to operator bias. In conclusion it can be said that from all the results analyzed it would appear that once operation conditions are fixed (viz operator, pH control) the precision of the method is adequate. The author wishes to thank Messrs African Explosives and Chemical Industries Limited for permission to publish these data. G. S. Stander and C. J. Kooij (Visitors): We must congratulate Mr Lee for this most interesting and useful development of the pick-up experimental method. It certainly provides research workers with an instrument which makes flotation more of a science and less of an art. We visited Mr Lee at his laboratory where he gave us a demonstration of the bubble pick-up instrument and technique as developed and improved by him.
Jan 12, 1969
-
The South African Institute of Mining and Metallurgy Information on Membership (d6d65ff1-4754-4393-a38e-3da5b7022c4f)
The Institute was founded in 1894 as the Chemical and Metallurgical Society of South Africa. In 1904 it was reconstituted as the Chemical Metallurgical and Mining Society of South Africa and in 1956 it became the South African Institute of Mining and Metallurgy. The objects of the Institute are to advance the science and practice of mining and metallurgy, to afford opportunities for the interchange and recording of knowledge of mining and metallurgy and to ensure high standards of professional conduct and competence. Membership benefits include monthly issues of the Journal of the Institute, monthly General Meetings at which papers are read, symposia, excursions to mining and industrial concerns and the use of club facilities at Kelvin House. Technical journals received on an exchange basis are available to members at the Johannesburg Public Library. The current membership of the Institute is over 1,600. Membership applications are accepted from suitably qualified persons and the requirements for entrance to the various grades of membership are summarised below. Fellows shall not be less than 30 years of age, shall be university graduates in pure or applied science or shall produce evidence to the satisfaction of the Council that they have successfully completed a co-ordinated course of study in pure or applied science of at least three years' duration at an approved university or institution deemed by the Council to be of equivalent status. Members shall have been employed in senior technical positions in important mining or metallurgical undertakings for at least five years or they shall have practised as mining or metallurgical consultants for at least five years. They shall be practising their profession at the time of application. Entrance fee RI0.00, Annual subscription RI7.00. Letters of designation: F.S.A.I.M.M. Members shall be not less than 25 years of age and shall be university graduates in pure or applied science, or shall have successfully completed co-ordinated courses of study in pure or applied science of at least three years' duration. They shall have been engaged in work of an approved technical character in the mining or metallurgical industries, of which not less than two years shall have been in positions of responsibility. A candidate shall be practising his profession at the time of his application. Entrance fee R8.00, Annual subscription RI5.00. Letters of designation: M.S.A.I.M.M. Associates shall be not less than twenty-five years of age, and shall have been engaged in positions of responsibility in, or associated with, the mining or metallurgical industries for periods of not less than three years. If, however, the candidate for admission to the higher grade of Associate, is at the time of his application, already a Student, he need satisfy the Council only that he is, at the time of his application, engaged in a position of responsibility in or associated with the mining or metallurgical industries. In all cases the applicants shall satisfy the Council that they are fit and proper persons to become Associates. Entrance fee R8.00, Annual subscription RI5.00. Graduates shall be not less than 21 years of age and shall be university graduates in pure or applied science, or have completed co-ordinated courses of study in pure or applied science of at least three years' duration at an approved university or institution. They shall not remain Graduate members after attaining the age of 30 years without the permission of Council. Entrance fee R2.00, Annual subscription R10.00. Students shall be persons not less than 18 years of age who are being educated or trained in a manner approved by the Council, to occupy a technical position in or associated with the mining or metallurgical industries and who, furthermore, shall not have attained the qualification required for a higher grade of membership. They may remain Students until they have obtained the necessary qualifications for transfer to a higher grade of membership, but not after the end of the Institute's financial year in which they attain the age of 28 (twenty-eight) years. They shall then transfer to a higher grade to retain membership of the Institute. The Council may relax the provisions of this clause in such cases as it considers appropriate. Entrance fee nil; Annual subscription R3.00. Other. The Council has the power to elect to the grade of Fellow or Member, candidates who may not fulfil all the requirements for entrance to these grades but whose status, professional achievements and practical experience in mining or metallurgy justify such election. Applications. Requests for membership application forms should be addressed on the attached form to the Secretary, South African Institute of Mining and Metallurgy, P.O. Box 61019, Marshalltown, Transvaal.
-
The South African Institute of Mining and Metallurgy Information on Membership (7fb22494-f066-4979-8b66-8e2cc824eaa7)
The Institute was founded in 1894 as the Chemical and Metallurgical Society of South Africa. In 1904 it was reconstituted as the Chemical Metallurgical and Mining Society of South Africa and in 1956 it became the South African Institute of Mining and Metallurgy. The objects of the Institute are to advance the science and practice of mining and metallurgy, to afford opportunities for the interchange and recording of knowledge of mining and metallurgy and to ensure high standards of professional conduct and competence. Membership benefits include monthly issues of the Journal of the Institute, monthly General Meetings at which papers are read, symposia, excursions to mining and industrial concerns and the use of club facilities at Kelvin House. Technical journals received on an exchange basis are available to members at the Johannesburg Public Library. The current membership of the Institute is over 1,600. Membership applications are accepted from suitably qualified persons and the requirements for entrance to the various grades of membership are summarised below. Fellows shall not be less than 30 years of age, shall be university graduates in pure or applied science or shall produce evidence to the satisfaction of the Council that they have successfully completed a co-ordinated course of study in pure or applied science of at least three years' duration at an approved university or institution deemed by the Council to be of equivalent status. Members shall have been employed in senior technical positions in important mining or metallurgical undertakings for at least five years or they shall have practised as mining or metallurgical consultants for at least five years. They shall be practising their profession at the time of application. Entrance fee R10.00, Annual subscription R17.00. Letters of designation: F.S.A.I.M.M. Members shall be not less than 25 years of age and shall be university graduates in pure or applied science, or shall have successfully completed co-ordinated courses of study in pure or applied science of at least three years' duration. They shall have been engaged in work of an approved technical character in the mining or metallurgical industries, of which not less than two years shall have been in positions of responsibility. A candidate shall be practising his profession at the time of his application. Entrance fee R8.00, Annual subscription R15.00. Letters of designation: M.S.A.I.M.M. Associates shall be not less than twenty-five years of age, and shall have been engaged in positions of responsibility in, or associated with, the mining or metallurgical industries for periods of not less than three years. If, however, the candidate for admission to the higher grade of Associate, is at the time of his application, already a Student, he need satisfy the Council only that he is, at the time of his application, engaged in a position of responsibility in or associated with the mining or metallurgical industries. In all cases the applicants shall satisfy the Council that they are fit and proper persons to become Associates. Entrance fee R8.00, Annual subscription R15.00. Graduates shall be not less than 21 years of age and shall be university graduates in pure or applied science, or have completed co-ordinated courses of study in pure or applied science of at least three years' duration at an approved university or institution. They shall not remain Graduate members after attaining the age of 30 years without the permission of Council. Entrance fee R2.00, Annual subscription R10.00. Students shall be persons not less than 18 years of age who are being educated or trained in a manner approved by the Council, to occupy a technical position in or associated with the mining or metallurgical industries and who, furthermore, shall not have attained the qualification required for a higher grade of membership. They may remain Students until they have obtained the necessary qualifications for transfer to a higher grade of membership, but not after the end of the Institute's financial year in which they attain the age of 28 (twenty-eight) years. They shall then transfer to a higher grade to retain membership of the Institute. The Council may relax the provisions of this clause in such cases as it considers appropriate. Entrance fee nil; Annual subscription R3.00. Other. The Council has the power to elect to the grade of Fellow or Member, candidates who may not fulfil all the requirements for entrance to these grades but whose status, professional achievements and practical experience in mining or metallurgy justify such election. Applications. Requests for membership application forms should be addressed on the attached form to the Secretary, South African Institute of Mining and Metallurgy, P.O. Box 61019, Marshalltown, Transvaal.
-
The South African Institute of Mining and Metallurgy
The Institute was founded in 1894 as the Chemical and Metallurgical Society of South Africa. In 1904 it was reconstituted as the Chemical Metallurgical and Mining Society of South Africa and in 1956 it became the South African Institute of Mining and Metallurgy. The objects of the Institute are to advance the science and practice of mining and metallurgy, to afford opportunities for the interchange and recording of knowledge of mining and metallurgy and to ensure high standards of professional conduct and competence. Membership benefits include monthly issues of the Journal of the Institute, General Meetings at which papers are read, symposia, excursions to mining and industrial concerns and the use of club facilities at Kelvin House. Technical journals received on an exchange basis are available to members at the Johannesburg Public Library. The current membership of the Institute is over 1 600. Membership applications are accepted from suitably qualified persons and the requirements for entrance to the various grades of membership are summarised below. Fellows shall not be less than 30 years of age, shall be university graduates in pure or applied science or shall produce evidence to the satisfaction of the Council that they have successfully completed a co-ordinated course of study in pure or applied science of at least three years' duration at an approved university or institution deemed by the Council to be of equivalent status. Members shall have been employed in senior technical positions in important mining or metallurgical undertakings for at least five years or they shall have practised as mining or metallurgical consultants for at least five years. They shall be practising their profession at the time of application. Entrance fee R10,00, Annual subscription R20,00. Letters of designation: F.S.A.I.M.M. Members shall be not less than 25 years of age and shall be university graduates in pure or applied science, or shall have successfully completed co-ordinated courses of study in pure or applied science of at least three years' duration. They shall have been engaged in work of an approved technical character in the mining or metallurgical industries, of which not less than two years shall have been in positions of responsibility. A candidate shall be practising his profession at the time of his application. Entrance fee R8,00, Annual subscription R18,00. Letters of designation: M.S.A.I.M.M. Associates shall be not less than twenty-five years of age, and shall have been engaged in positions of responsibility in, or associated with, the mining or metallurgical industries for periods of not less than three years. If, however, the candidate for admission to the higher grade of Associate, is at the time of his application, already a Student, he need satisfy the Council only that he is, at the time of his application, engaged in a position of responsibility in or associated with the mining or metallurgical industries. In all cases the applicants shall satisfy the Council that they are fit and proper persons to become Associates. Entrance fee R8,00, Annual subscription R18,00. Graduates shall be not less than 21 years of age and shall be university graduates in pure or applied science, or have completed co-ordinated courses of study in pure or applied science of at least three years' duration at an approved university or institution. They shall not remain Graduate members after attaining the age of 30 years without the permission of Council. Entrance fee R2,00, Annual subscription R12,00. Students shall be persons not less than 18 years of age who are being educated or trained in a manner approved by the Councils to occupy a technical position in or associated with the mining or metallurgical industries and who, furthermore, shall not have attained the qualification required for a higher grade of membership. They may remain Students until they have obtained the necessary qualifications for transfer to a higher grade of membership, but not after the end of the Institute's financial year in which they attain the age of 28 (twenty-eight) years. They shall then transfer to a higher grade to retain membership of the Institute. The Council may relax the provisions of this clause in such cases as it considers appropriate. Entrance fee nil; Annual subscription R5,00. Other. The Council has the power to elect to the grade of Fellow or Member, candidates who may not fulfil all the requirements for entrance to these grades but whose status, professional achievements and practical experience in mining or metallurgy justify such election. Applications. Requests for membership application form should be addressed on the attached form to the Secretaries South African Institute of Mining and Metallurgy, P.O. Box 61019, Marshalltown, Transvaal.
-
The South African Institute of Mining and Metallurgy Information on Membership (bdd04b38-9bae-41b9-85f2-d0c6727adb92)
The Institute was founded in 1894 as the Chemical and Metallurgical Society of South Africa. In 1904 it was reconstituted as the Chemical Metallurgical and Mining Society of South Africa and in 1956 it became the South African Institute of Mining and Metallurgy. The objects of the Institute are to advance the science and practice of mining and metallurgy, to afford opportunities for the interchange and recording of knowledge of mining and metallurgy and to ensure high standards of professional conduct and competence. Membership benefits include monthly issues of the Journal of the Institute, monthly General Meetings at which papers are read, symposia, excursions to mining and industrial concerns and the use of club facilities at Kelvin House. Technical journals received on an exchange basis are available to members at the Johannesburg Public Library. The current membership of the Institute is over 1,600. Membership applications are accepted from suitably qualified persons and the requirements for entrance to the various grades of membership are summarised below. Fellows shall not be less than 30 years of age, shall be university graduates in pure or applied science or shall produce evidence to the satisfaction of the Council that they have successfully completed a co-ordinated course of study in pure or applied science of at least three years' duration at an approved university or institution deemed by the Council to be of equivalent status. Members shall have been employed in senior technical positions in important mining or metallurgical undertakings for at least five years or they shall have practised as mining or metallurgical consultants for at least five years. They shall be practising their profession at the time of application. Entrance fee R10.00, Annual subscription RI7.00. Letters of designation: F.S.A.I.M.M. Members shall be not less than 25 years of age and shall be university graduates in pure or applied science, or shall have successfully completed co-ordinated courses of study in pure or applied science of at least three years' duration. They shall have been engaged in work of an approved technical character in the mining or metallurgical industries, of which not less than two years shall have been in positions of responsibility. A candidate shall be practising his profession at the time of his application. Entrance fee R8.00, Annual subscription RI5.00. Letters of designation: M.S.A.I.M.M. Associates shall be not less than twenty-five years of age, and shall have been engaged in positions of responsibility in, or associated with, the mining or metallurgical industries for periods of not less than three years. If, however, the candidate for admission to the higher grade of Associate, is at the time of his application, already a Student, he need satisfy the Council only that he is, at the time of his application, engaged in a position of responsibility in or associated with the mining or metallurgical industries. In all cases the applicants shall satisfy the Council that they are fit and proper persons to become Associates. Entrance fee R8.00, Annual subscription R15.00. Graduates shall be not less than 21 years of age and shall be university graduates in pure or applied science, or have completed co-ordinated courses of study in pure or applied science of at least three years' duration at an approved university or institution. They shall not remain Graduate members after attaining the age of 30 years without the permission of Council. Entrance fee R2.00, Annual subscription R10.00. Students shall be persons not less than 18 years of age who are being educated or trained in a manner approved by the Council, to occupy a technical position in or associated with the mining or metallurgical industries and who, furthermore, shall not have attained the qualification required for a higher grade of membership. They may remain Students until they have obtained the necessary qualifications for transfer to a higher grade of membership, but not after the end of the Institute's financial year in which they attain the age of 28 (twenty-eight) years. They shall then transfer to a higher grade to retain membership of the Institute. The Council may relax the provisions of this clause in such cases as it considers appropriate. Entrance fee nil; Annual subscription R3.00. Other. The Council has the power to elect to the grade of Fellow or Member, candidates who may not fulfil all the requirements for entrance to these grades but whose status, professional achievements and practical experience in mining or metallurgy justify such election. Applications. Requests for membership application forms should be addressed on the attached form to the Secretary, South African Institute of Mining and Metallurgy, P.O. Box 61019, Marshalltown, Transvaal.
-
The use of continuous miners in South African coal mines
By J. D. Stone, I. D. Brumby, J. D. Inch, C. J. Beukes
A. Continuous miners, and their operation at Bosjesspruit Colliery J. D. INCH*, B.Sc. (Min.), M. I. Min. E. (Visitor) A brief description is given of the main types of continuous miner and their incidence of application in South Africa. Definitions and descriptions of the design parameters and components of the main cutting head are given. together with an outline of the modifications carried out to improve machine cutting performance. An account is given of experience with the application of water infusion to suppress airborne dust during continuous-miner operations. B. The selection and performance of continuous miners at Matla Coal by J. D. STONE, B.Sc. Eng. (Min.,) M.B.L. (Graduate) The reasons for the choice of continuous miners for the development of accesses and the winning of coal in a modern underground coal mine are discussed. It is shown that, at relatively low depths, the extraction rate as well as the costs are more favourable than those of proved total extraction methods. The selection of a continuous miner is largely dictated by factors such as production rate, capital and running costs, imported content and the extent to which local content and manufacturing are to be increased, manpower requirements, seam thickness, expected floor and roof conditions, and maximum cutting height. The present inherent shortcomings of continuous miners, such as inefficient continuous transportation of coal away from the miner and the lack of an infinitely variable traction to match the sumping speed with the feasible penetration speed, are pointed out. Specific problems encountered and the methods of solving them, as well as a planned trial with a heavy-duty continuous miner, are discussed. C. Continuous mining within the Tavistock Group of collieries I. D. BRUMBY.Dip. Min. (Visitor) The Tavistock Group of collieries is situated some 25 km south of Witbank. The three collieries comprising the Group are Tavistock Colliery, Phoenix Colliery, and South Witbank Coal Mines. Continuous mining is practised to some degree at all three collieries. This system of mining was introduced at Phoenix during 1976, South Witbank during 1978, and Tavistock during 1979. For the twelve months ended June 1979, continuous mining accounted for 1,7 Mt of the 4,5 Mt hauled from underground. All the continuous miners introduced to date have been of the rotary-drum type. D. Pillar extraction at Usutu Collieries using continuous miners by c. J. BEUKES(Visitor) In 1969 Usutu Collieries began pillar extraction with conventional mechanized equipment. This was very successful, but certain disadvantages could be eliminated if continuous miners were used instead. In 1976 the first continuous miner was introduced for this purpose; this proved so successful that a second unit was introduced in 1977, and pillar extraction by conventional equipment was discontinued. By the end of 1978, 1,3 Mt had been mined from pillar extraction by continuous miners. This paper describes the method in some detail, and indicates that the operational costs are lower than for conventional bord-and-pillar mining. Defect solid state A one-day multidisciplinary symposium entitled 'The Defect Solid State '80' will be held under the auspices of the Solid State Physics and Materials Science Subcommittee of the South African Institute of Physics at the University of the Witwatersrand on Monday, 14th July, 1980, following the Twenty-fifth Annual Conference of the South African Institute of Physics.
Jan 1, 1980
-
Notices (7ae1d864-cc09-466f-a298-f304f752077e)
SYMPOSIUM ON THE RECOVERY OF PYRITE The proceedings of the Symposium on the Recovery of Pyrite, held in Johannesburg in June 1969, may be ordered from the Secretary, S.A.I.M.M., P.O. Box 61019, Marshalltown, Transvaal, at the reduced price of R5.00. Papers and addresses presented at the Symposium were: Opening Address by Mr J. K. E. Douglas (President). "The world sulphur position," by W. C. J. van Rensburg (Member). "The South African sulphur position," by D. L. Taylor (Member). "The recovery of pyrite at Government Gold Mining Areas Limited," by R. J. Westwood (Member), G. S. Stander (Affiliate) and H. P. Carlisle (Member). "Recovery of pyrite concentrates from colliery-waste discards-A preliminary assessment," by W. A. Gilbert (Visitor) and E. A. Nugent (Member). "The role of pyrite in upgrading the uranium content of Witwatersrand conglomerate ores by means of the heavy-medium separation process," by D. J. Tutt (Associate Member). "Pyrite recovery by jigs at Durban Roodepoort Deep Limited," by E. J. Dominy (Affiliate), F. Diamond (Affiliate) and A. D. Graham (Affiliate). "The storage of pyrite concentrates," by Joan C. Campkin (Visitor) and P. J. Lloyd (Member). "The flotation plants of the Anglo-Transvaal Group," by L. A. Bushell (Member). "Pyrite flotation with amines and cyanidation of the products," by E. H. D. Carman (Member). "Gold recovery by cyanidation from mill products obtained after pyrite flotation," by P. G. Mrkusic (Graduate), M. Sciarone (Visitor) and H. E. Simonsen (Visitor). "The influence of sulphydryl and cationic flotation reagents on cyanidation of native gold," by K. G. Ashurst (Visitor) and W. P. Finkelstein (Member). "Laboratory tests on the flotation of pyrite from Witwatersrand gold ores by cationic collector," by J. Levin (Member), and M. L. Veitch (Visitor). Closing Address, by Dr R. E. Robinson (Director, National Institute for Metallurgy). INCOME TAX: POST-GRADUATE STUDY COURSE CONCESSION As a result of representations made by the Associated Scientific and Technical Societies of S.A. and the Suid-Afrikaanse Akademie vir Wetenskap en Kuns, engineers and scientists will now be allowed to deduct expenses incurred on post-graduate study courses from their taxable income. The conditions of this concession are set out in section 16 of the Income Tax Act, 1969, which reads as follows: 16. (1) The following section is hereby substituted for section 16 of the principal Act: 16. "Notwithstanding the provisions of section 23(a) and (b), there shall be allowed to be deducted from the income of any person who is a dentist or medical practitioner or practises any profession referred to in paragraph (a), so much as the Secretary may allow of any expenditure incurred by such person in the circumstances contemplated in paragraph (c), if the Dental Association of South Africa in the case of a dentist, or the Medical Association of South Africa in the case of a medical practitioner, or the "Suid-Afrikaanse Akademie vir Wetenskap en Kuns" or the Associated Scientific and Technical Societies of South Africa in any other case, certifies in such form as the Secretary may prescribe that such person- (a) if he is not a dentist or medical practitioner, is the holder of a degree in engineering or allied technology or natural sciences awarded by a recognized university on completion of a prescribed minimum period of study of not less than four academic years or the equivalent thereof and enabling the holder thereof to practise the profession of an engineer or a profession for which advanced and specialised scientific knowledge is required which relates directly to- (i) the development or exploitation of natural resources; (ii) mining or prospecting for minerals; (iii) the production of pastoral, agricultural or forest produce ; (iv) the breeding or care of farm animals; (v) any industrial process; or (vi) the training of specialists in any branch of science or technology connected with any aforementioned profession; (b) has practised his profession for not less than three years; and (c) has incurred such expenditure during the year of assessment in respect of the attendance by him of any postgraduate study course approved by such body to improve his qualifications for carrying on his profession in the Republic". (2) The amendments effected by subsection (1) shall first take effect in respect of assessments for the year of assessment ending on the twenty-eighth day of February, 1970. From this section it is clear that the concession will only be granted if the application is accompanied by a certificate, which certificate must be either signed by the Chairman of Die Akademie or the President of the Associated Societies. In terms of the authority granted such certificates must certify that: (i) the taxpayer concerned has practised his profession for not less than three years; (ii) the expenditure was incurred by the taxpayer during the year of assessment indicated in the certificate; (iii) the expenditure was incurred by the taxpayer in respect of the attendance by him of a post-graduate study course approved by the Associated Scientific and Technical Societies of South Africa or Die Suid-Afrikaanse Akademie vir Wetenskap en Kuns, as the case may be, to improve his qualifications for carrying on his profession in South Africa; (iv) the taxpayer is the holder of a degree in engineering or allied technology or natural sciences, which degree was awarded by a recognized university,
-
Surface Mining And Its Socio-Economic Impacts And Challenges
By Stephen Yirenkyi
The mining industry remains the backbone of many economies in the developing world. Its resurgence in Ghana since 1989 was driven by the global paradigm which emphasizes private sector-led development as the engine of economic growth in developing countries. The historical importance of mining in the economic development of Ghana is evident in the country?s colonial name, Gold Coast (Akabzaa T. and Darimani A., 2001). Ghana earned $2.5 billion from mineral exports in 2007. 20,000 people are employed in large-scale mining whilst 500,000 are employed in the small-scale sector. Mining contributes about 7% of Ghana?s total corporate tax earnings, 41% of total exports, 12% of revenue collected by the Internal Revenue Service and 5% of Gross Domestic Product (Ghana Chamber of Mines, 2008). Gold dominates the mining sector and the country is Africa?s second largest gold producer after South Africa. Surface Mining, which refers to a method of extracting minerals from the earth by their removal from an open pit or borrows, requires a large tract of land for its operations (Wikipedia, 2008). There is therefore a continuous divergence of interest between land required for surface mining and other land uses such as farming and housing, among others. In recent years, surface mining has been promoted in many mining countries because of the following reasons: ?Cost considerations compared to underground mining; ?Safety considerations, compared to underground mining; ?Low grade ore which requires processing huge quantities; ?Location of the ore bodies; and ?Competition among gold producing countries for investors. This paper looks at the socio-economic impacts and challenges of surface mining by using Gold Fields Ghana Ltd. Tarkwa, Ghana as a case study. The company has a concession of about 208 sq km located in the heart of the Wassa communities in the Western Region of Ghana and undertakes surface mining like most of the other mining companies in the country. Gold Fields, Tarkwa mine produces 700,000 ounces of gold a year with the potential of increasing this output to 800,000 ounces after its current expansion programme. Some of the effects of surface mining identified were: 1. Relocation/Resettlement of host communities and its negative effects; 2. Disturbance to Flora and Fauna; 3. Disturbance to Sacred Places; 4. Land Degradation; 5. Noise and Air Pollution; and 6. Water Pollution. This paper sought to investigate the measures put in place by the government and the Gold Fields Ghana Ltd. to mitigate the above effects in order to ensure peaceful coexistence between the mining company and its host communities. It concludes that most mining companies presume the provision of socio-economic development in mining communities will lead to the company securing a social license to operate. This however is not true but rather effective community relations combined with socio-economic development. According to Gold Fields Ghana Ltds. model, this involves continuous community engagement, conflict resolution and comprehensive environmental monitoring programme which will all lead to effective community relations. The strategies to ensure socio-economic development involves community development programme, livelihood restoration programme and community training and employment. All these will then lead to sustainable development which will ensure the company?s social license to operate. Gold Fields? model is in line with the principles of responsible mining. With this model, the community feels they are part of the company and the social license of the company is guaranteed. Gold Fields? model, which has been tried and tested for the past five years, could serve as a template with suitable modification for local conditions for other mining countries where surface mines operate.
Jan 1, 2008
-
The intensive cyanidation of gold-plant gravity concentrates
By D. Duncanson, R. J. Davidson, C. G. S. Schmidt, G. A. Brown, J. D. Taylor, N. W. Hanf
The development of a cyanidation route for the treatment of gold-plant gravity concentrates is described. This work was carried out as a natural consequence of earlier improvements to the recovery of gold in the gravity sections of existing gold plants. Concern about the environmental aspects of the conventional amalgamation process was further motivation in the development of an alternative procedure. It was found that the partial pressure of oxygen in solution was the most critical reactionrate determining factor. The rate of gold dissolution was shown to be controlled by the reaction rate below approximately 25°C and by diffusion above that temperature. Thus, the efficiency of pulp agitation and oxygen partial pressure permitted a high degree of control over the rate of gold dissolution. The use of oxygen rather than air significantly increased the dissolution rate of both gold and silver. The solubilities of sodium, calcium, and potassium aurocyanide complexes under simulated reaction conditions were studied, and it was established that the values for the sodium and calcium complexes were limited, requiring the use of lower pulp densities and higher reaction temperatures for the treatment of very high-grade concentrates. The presence of excessive amounts of tramp iron in such concentrates of up to 25 per cent by mass was found to result in poor gold dissolution owing to the cementation of gold under certain reaction conditions. The maintenance of high oxygen partial pressures, together with high cyanide concentrations, high pH levels, and the presence of calcium in the system, all aided in passivating the tramp iron. Copper, gold, and iron were shown to be the main cyanide-consuming elements. Optimum gold dissolution was obtained in a closed bench-scale reactor incorporating a flotation-machine type of agitator for effective pulp agitation and oxygenation, the oxygen being recirculated. The reactor was designed to operate under a very small positive pressure. After reaction times of 2 to 6 hours at temperatures in the region of 30°C, both the gold and the silver dissolution averaged 99,S per cent. In the case of very high-grade concentrates, it was shown that gold could be floated in the same reactor by drawing off the flotation concentrate through a port in the reactor. A flotation recovery of 87,4 per cent of the gold in 3,9 per cent by mass was obtained. The recovery of osmiridium from cyanide-leach residues and the electrowinning of gold from the pregnant liquors were also considered as processing aspects in the treatment of gold-plant belt concentrates. Final table tailings with a gold concentration of 10to 12 gft were obtained. The results of the investigation strongly suggested that an alternative cyanidation route for the treatment of gold-plant concentrates was technically feasible, provided the system included effective agitation and oxygenation. In the case of lower-grade concentrates, cyanidation followed by the electrowinning of gold appears to be the simplest route, while, for high-grade concentrates, flotation and smelting of the concentrate followed by cyanidation of the flotation tailings are suggested. The use of oxygen rather than air for sparging the pulp would depend largely on the grade of material to be treated. A preliminary comparison of the costs related to the amalgamation and cyanidation processes for the recovery of gold from such concentrates indicated very similar capital and operating costs. It was concluded that other considerations, e.g. toxicity, safety, and lower labour requirements, were more important than such small cost differences. Furthermore, the 'opening' of the gold-plant gravity circuit, which would be made possible by a cyanidation route, would further reduce the operating costs because of the subsequent decrease in the tonnage to be treated.
Jan 1, 1978
-
Proceedings September General Meeting
The September General Meeting of the Institute was held in Kelvin House, Johannesburg, on 16th September, 1970, at 3.00 p.m. Mr V. C. Robinson (President) was in the Chair. There were also present one hundred and eighteen Fellows, including Dr J. M. Bereza, H. P. Carlisle, R. J. C. Goode, Dr J. P. Hugo, P. Lambooy, Prof R. P. Plewman, W. W. Malan, Dr J. T. McIntyre, Dr M. D. G. Salamon, L. W. P. Van den Bosch, P. A. von Wielligh (Council Members), A. Bain, G. P. Bennet, D. L. Carson, G. L. H. Diering, M. E. E. Douglas, F. A. B. Fouche, R. Fourie, A. R. C. Fowler, E. B. Gordon, J. S. Hay, G. H. Henderson, S. D. Hill, A. C. Hofmeyr, J. M. Jacobs, A. F. Lee, D. G. Malan, L. J. Prince, W. G. Pyne-Mercier, A. H. Mokken, Dr W. S. Rapson, R. R. Richardson, H. V. Solomon, C. G. Sowry, G. G. Stanley, G. R. Still, D. L. Starkey, D. L. Taylor, E. W. Thiel, I. E. Van Aswegan, M. van Ryneve1d Steyn, N. B. Vinson, H. Wheeler, Dr A. Whillier, R. A .Wilson, C. F. Ziervogel. Forty-two Members including R. C. Bertram, F. Collier, G. C. Currie, O. Davel, J. M. Gosnell, A. Hazell, Dr N. C. Joughin, F. Kleinschmidt, D. Love, R. B. Macgillivray, D. Mather, R. D. R. Munro, R. S. Pearson, J. J. Peisl, T. J. Pole, A. J. Rossouw, R. G. B. Skirving, G. S. Schwartz, K. Stee1e, H. A. G. Slater, A. Taylor, B. A. Thomas, P. L. Vaughan, D. T. Watt, W. Wilson. Nineteen Associates including R. K. Briggs, S. I. Du Preez, P. G. Gaylard, P. H. Hartslief, W. M. Mackay, A. D. Ross. Three Students: V. S. Care, R. J. Drummond, P. J. Pretorius. Thirty-one Visitors including C. P. S. Barnard, D. W. Bosch, M. Bain G. L. Brown, G. D. Behrens, C. Coetzer, D. M. Gilbart-Smith, R. L. Man, Dr G. J. Stander, M. W. L. Steinobel, R. H. E. Thorpe, T. D. van Wyk, P. H. van Zyl, E. Vereecken, J. J. H. Viljoen. Secretary, D. C. Visser. Total present: 215. OBITUARIES The President: "It is my sad duty to announce the death of the following: Bruce Donaldson Crawford, Fellow, who joined the Institute in 1951 and passed away on 29th April, 1970. Donald Joseph Powrie, Life Fellow, who joined the Institute in 1935 and passed away on 22nd July, 1970. As a mark of respect to the memory of the deceased and in sympathy with the bereaved I would ask you all to rise and observe a few moments' silence." MEMBERSHIP The President: "I have much pleasure in announcing that the names of the under-mentioned candidates, having been published in accordance with By-Law 5.2.2, Council has elected them to membership of the Institute in the following grades: Associate: WiIliam Norman Carter. Students: Roman Michael Dabrowski, Sean George Dean Eaton, Alan Philip Stonham Howard, Anton du Preez Roos, Richard Harold Tourle. MEMBERS TRANSFERRED TO A HIGHER GRADE From Graduate to Member: Terrance Alexander Ward. From Associate to Member: Bernard Andre Thomas. "I welcome the newly elected members to the Institute and congratulate the members who had been transferred to a higher grade." CO-OPTION The President: "I wish to advise members that, in terms of clause 3.9 of the Constitution, Mc. H. P. Carlisle had been co-opted to serve on Council." PAPERS FOR PRESENTATION The President: "We have two papers today, and I am first going to call on Dr Stander the Head of the Water Division of the C.S.I.R., who IS well known to many of you for his work and talks on pollution, who has had more than a little to do with this industry, and who has been I would say, of the greatest possible assistance to the mining industry in overcoming the problems of pollution which are so prevalent in industry of this nature. He, Mr Henzen and Mr Funke have written this paper, 'The disposal of polluted effluents from mining, metallurgical and metal-finishing industries, their effects on receiving water and remedial measures.' This is the Water Year, as you know, and it is most appropriate that we should have such an authority to talk to us on this very important topic. I now have much pleasure in asking Dr Stander to introduce his paper." After the presentation of the paper the President said, "Gentlemen, I am sure that you would like me on your behalf, to thank Dr Stander very sincerely for a paper which I think has enabled us to get a completely new slant on the Water Year. There are many people who have put their finger on this campaign and said, it is all a gimmick. There are others-I suppose notably some of the bridge clubs which operate on week-day afternoons in Parkview-who seem to think that this is a quick way of getting early rain. Of course, it is not. This is a most important paper which we have had given to us this afternoon. You probably found it here when you arrived and have not read it-I was very lucky to be able to read it last night, and there is an awful lot of meat in it. For as long as I have been associated with mining in any way, there has been a problem of polluted effluent-of effluents carrying a mineral load from mining, and I think Dr Stander is absolutely right-and, of course, the Commission is right when they say that this is not merely the problem of mine management or mine owners-this is a problem which affects every single human being in this country.
-
Annual General Meeting of the Institute
The Annual General Meeting of the South African Institute of Mining and Metallurgy was held in Kelvin House on Wednesday, 25th August, 1976. Dr R. E. Robinson, (President) was in the chair, and declared the meeting open at 16h00. Obituaries The president: It is my sad duty to announce the death of the following members of the Institute : P. A. Creewell, Life Fellow; A. S. Davis, J. S. Hay, P. O. Large, N. McCaskell, and H. G. M. McKerrow, Life Members; C. L. Bererge, Fellow; T. Bulloch, G. Douglas, R. W. Forrester, and C. G. P. Sack, Members; P. R. Garcia, W. A. Naude, and J. P. Slager, Associates. As a mark of respect to the memory of the deceased and in sympathy with the bereaved, I ask you to rise and observe a few moments' silence. Minutes The President: May we confirm the minutes of the General Meeting held on March 17th, 1976, as published in the June issue of the Journal? Agreed. Welcome The President: It is my pleasant duty to welcome a number of guests and distinguished visitors this evening. First, I would like to welcome Mr R. Plumbridge, the President of the Chamber of Mines, and Mrs Plumbridge. We have had very close co-operation with the Chamber of Mines, and it is particularly gratifying that Mr Plumbridge has had time to be with us this evening in spite of very heavy engagements. Ook 'n spesiale woord van verwelkomirg aar mrr. N. Orsmord, die Staatsmyringerieur, en mev. Orsmord. Ors wil hierdie geleertheid gebruik om mrr. Orsmord geluk to wens met sy aarstellirg as die Staatsmyrirgerieur en die hoop uitspreek dat dit baie jare van samewerkirg met hierdie Irstituut sal beteker. We also welcome guests who, in one way or another, have been able to attend most of our Annual General Meetings, the Honourable I. B. Dillon, the Minister of Mines of Rhodesia, and Mrs Dillon. Once again we welcome them most heartily to our Annual Meeting. I would also like to welcome the representatives of many of our sister institutions : the Honorary Treasurer of the AS & TS, Mr D. G. Maxwell; the President of the South African Institution of Mechanical Engineers, Mr A. R. Adams; the Vice-President of the South African Institute of Electrical Engineers, Mr K. A. H. Adams, and Mrs Adams; the President of the Institute of Certificated Mechanical and Electrical Engineer s, Mr Martin and Mrs Martin; a member of the Executive of the South African Institute of Civil Engineers, Professor G. Bright ; the President of the South African Chemical Institute, Mr Vic Shuller, and Mrs Shuller; the President of the Institute of Welding, Professor F. P. A. Robinson, and Mrs Robinson; the President of SACPE, Mr M. R. Gericke ; the President of the Institution of Metallurgists, South African Branch, Mr D. R. Allen; the President of FSPE, Dr P. J. D. Lloyd, and Mrs Lloyd ; Mr A. J. H. Pole of the Association of Mine Managers, and Mrs Pole; and Mr M. D. Hoskin of the South African Institute of Foundrymen. A special word of welcome to Mr G. C. Young of our Orange Free State Branch, and Mrs Young ; and to Mr E. J. Jackson of our Witbank/Middelburg Branch. We have great pleasure in welcoming Dr F. M. Naude, the Scientific Adviser to the Prime Minister, and Dr W. C. J. van Rensburg, Technical Director of the Minerals Bureau. The latter is a new organization, and we hope their attendance here this afternoon forecasts a long period of co-operation between the Minerals Bureau and this Institute. Ook wil ek hartlik hier verwelkom die Rektor van Die Randse Afrikaanse Universiteit, professor G. van N. Viljoen. Ors het baie noue samewerking met die Universiteit gekry, en ek wil ook bier verwelkom die twee verteenwoordigers van die Geologiese-afdeling en die Chemie-afdeling, naamlik, dr C. Roering en professor G. W. Holzapfel. Last, but by no means least, a word of welcome to a very old friend, Mr Eric Boden, the Manager of AS & TS. To all our guests, a very hearty welcome to this our Annual General Meeting. Membership The President: It is required by our Constitution that I announce the names of a number of candidates who have been elected to various grades of membership. The list is a very long one, and I suggest that we simply record that these names will be published in the Journal. Any one who wishes to comment on these members should do so in writing to our Secretary. Agreed. Fellows: G. Paterson, P. H. Adler, F. W. G. Schoning, J. P. de Villiers, F. I. de Waal, J. R. H. Shaw. Members: C. J. Slavin, P. J. Perkins, R. J. I. Butler, A. M. Hattingh, C. E. Alvey, J. A. Engelbrecht, P. L. Gouws, J. P. Martin, J. F. Taylor, K. A. G. Blendulf, A. R. Gibb, W. E. Smith. Associate Members: D. R. Broderick, D. F. Cilliers, D. N. Stuart, P. Kraus, B. G. Pinder. Associates: D. E. Gibbon, D. F. Jacobs, R. F. W. Swanepoel, R. D. H. Bebb, H. H. Vernall, R. D. Gibson, J. P. van Wyk. Graduates : A. N. Morris, D. J. Payne, G. S. Worthington, A. S. Dennison, A. R. Godfrey, N. Holloway, W. J. Rankin, G. S. Lyndon, R. J. van Proctor, J. J. Versluis, G. M. Miller. Students: B. J. Rabie, G. D. Webber, W. L. Blair, I. D. Mathews, K. McVey, S. W. Beer, R. W. J. Bentley,
Jan 10, 1976
-
Proceedings March General Meeting
The March General Meeting of the Institute was held in Kelvin House, Johannesburg on 18th March, 1970, at 4.30 p.m. Mr J. K. E. Douglas (President) was in the Chair. There were also present fifteen Fellows, Messrs H. Britten, R. C. J. Goode, Prof D. D. Howat, Mr T. C. A. Meyer, Dr R. E. Robinson, Messrs V. C. Robinson and P. W. J. van Rensburg (Council Members), S. K. de Kok, Dr N. P. Finkelstein, Messrs K. W. Findlay, H. N. Hepker, J. Levin, Dr K. A. Murray and Mr A. H. Mokken. Four Members including Mr D. Ayres, Dr M. I. Britten and Dr A. Granville. One Associate: Mr G. S. Stander. One Student, Mr R. N. Guest. Four Visitors, Messrs S. A. Allison, C. N. Leibb, C. J. Kooij and A. Mavrogordato. Secretary: Mr D. C. Visser. Total present: Twenty-seven. OBITUARY The President: "It is my sad duty to announce the death of Henrik Johannes Van Eck, Honorary Life Member, who joined the Institute in 1929 and passed away on 18th February, 1970. Dr van Eck started life as a chemist and chemical engineer and, as we all know, he rose to become one of our most distinguished leaders of industry in the country. On many important occasions we, in this Institute, have been privileged to have him address us on subjects which were always of great importance and relevance to the developments in this country. He was a man of great vision and imagination and could put across his ideas in a most eloquent and convincing manner. In his important position as chairman of the Industrial Development Corporation and of Iscor, whatever he said carried great weight. Busy as he was he always found time to participate not only in the affairs of this Institute but in many other technical and public bodies. His passing is a great loss to South Africa and we in this Institute wish to associate ourselves with the many other tributes which have been paid to this great man. We extend our sympathy to his wife and family and as a mark of respect I would ask you to rise and observe a few moments silence." MEMBERSHIP The President: "I have much pleasure in announcing that the names of the undermentioned candidates, having been published in accordance with By-Law 5.2.2, Council has elected them to membership of the Institute in the following grades: Fellow: Ian Douglas Bruce Corner, Joachim Bernhard Rolfes. Member: Michael Vernon Nolan. Associate: Karl Franz Wilhelm Eick. MEMBERS TRANSFERRED TO A HIGHER GRADE From Member to Fellow: Nilo Zolezzi. From Graduate to Member: Roger Billingham. I welcome the newly elected members to the Institute and congratulate the members who have been transferred to a higher grade." PAPERS FOR PRESENTATION The President: (i) "Mr Lee, may I call on you to deliver your paper entitled 'A new bubble pick-up technique as a rapid flotation test method'." After the presentation of the paper the President said: "The paper which Mr Lee introduced this afternoon was a short one but was nonetheless important in that it described a new tool for use in flotation test work. Those of us who have experienced the frustration of trying to solve flotation problems by trial and error methods know what this means. I well remember 25 years ago at T.G.M.E. trying to improve the recovery from the flotation plant there by trying various combinations of reagents and then having to wait a couple of days for the assay office to give results. Even then, on the small scale laboratory tests which had to precede full scale tests one could never be sure that the results obtained were reproducible on the full scale. Here it seems we have a relatively simple apparatus which can measure instantly the effectiveness of various reagents under different concentrations and pH values, etc. It is most important, I believe, that developments of this kind be reported in our journal for the benefit of all involved in such work, not only so that we know about it but also in order to provoke constructive discussion which might lead to further developments. I would like to invite members, therefore, to submit papers or notes on important
-
Author's Reply to Discussion (6892bdec-7740-4c72-9841-329b5421e505)
Solvent loading: It is agreed that it is advantageous, as far as reagent cost is concerned, to operate at maximum solvent loading. However, owing to the fact that no reliable automatic solvent flow controller is yet available, control tends to be erratic with the result that there is risk of losing uranium. As can be seen from Mr Tunley's plot, the graph representing total ammonia cost is fairly flat between loadings of 3.5 and 4.0 gpl, while the graph representing uranium loss in the raffinate is steep. It is, therefore, safer to operate slightly below optimum loading in the absence of absolute control. Should the purity of the final product gain importance, operation at optimum loading or even slightly above, may be advantageous. Solvent losses and clarification of pregnant solution: The cost of replacing solvent, as indicated by Mr Carman, represents a high percentage of the overall Purlex costs. It is, therefore, agreed that, amongst other factors, efficient clarification of the pregnant solution and mixer-settler design have an important bearing on the cost. However, as at Blyvooruitzicht, the Buffelsfontein plant can tolerate a suspended solids content of 50 ppm without serious deterioration in efficiency. An increase in the suspended solids content from 15 to 50 ppm normally accounts for an increase of approximately 1 ppm in amine loss. Clarification of acidic pregnant solutions is much more difficult than that of alkaline solutions. Sand clarifiers are being used at Buffelsfontein with moderate success. Clarified solutions containing less than 20 ppm of solids in suspension can be produced, depending on the quantity and type of flocculant used in the filtration process, the thickness and the grading analysis of the sand beds and the quality of supervision. An on-stream duty of approximately 0.15 gallon per sq ft of surface area is obtained. Hydraulic handling of clarifier sand, while cleaning, may effect the efficiency of a clarifier, as size segregation of sand particles may lead to inefficient "pockets" in a sand bed. Control of the solution level in the sand clarifier also affects the quality of the effluent. Exposure of the sand bed invariably causes a cloudy effluent. Recycling of the final and initial solution discharged before and after skimming the clarifier sand improves the clarification efficiency significantly. Post-precipitation of silica and possibly sulphate salts, after clarification, may give a false impression of inefficient clarification. This phenomenon is more pronounced when treating hot supersaturated solutions. Ageing and cooling of the solution before clarification assist in stabilising the solution and reduce precipitation after clarification. The maintenance cost of sand clarifiers at Buffelsfontein is in the order of 0.35 cent per metric ton of solution treated. A redundant ion-exchange column has been tested successfully, either as a primary or a secondary clarifier, depending on the quality of the filtrate treated. The conventional pebble and sand beds in the column have been retained. Operation was enhanced by the addition of a two-foot deep resin bed as a filtering medium. The suspended solids content was reduced to less than 5 ppm. Mixer-settlers: Mixer-settler design is a controversial subject but, in view of the high costs of solvent compared to relatively low pumping costs, it is believed that mixing and pumping functions should be separated. Separate facilities for pumping and mixing not only give greater operational flexibility but also permit eventual changes in the flow circuit as technology develops. Scrub technique: Unlike the pilot plant, where the crud was carried away in the aqueous phase, crud is carried over with the organic phase in the full-scale plant. This carry-over of crud into the strip bank aggravates crud formation in the first strip stage. This phenomenon may result from a slight difference in settler design and/or a variation in the relative phase depths in the two plants. Bypassing of the scrub aqueous solution from the fourth to the second stage was introduced in order to avoid dilution and partial neutralisation of the acid added to the third stage, as it is known that a low pH value enhances the transfer of iron into the aqueous phase. The low aqueous flowrate in the third scrubbing stage was overcome by introducing an aqueous phase recycle. Gleaning: Mr MacDonald's contribution on "gleaning" was most informative. This process for recovering solvent from raffinate seems to show at least as much promise as coalescers and other methods employed to date. Similar tests conducted at Buffelsfontein pilot plant gave 60 per cent amine recovery from raffinate containing 10 ppm amine. However, the circuit was not operated at equilibrium and recovery may be expected to drop as the amine concentration of the "Gleaner" circuit increases.
-
Annual General Meeting of the Institute
The Annual General Meeting of the Institute was held in Kelvin House, Johannesburg, on Wednesday, 22nd August, 1973. Dr J. P. Hugo (President) was in the Chair. There were also present 64 Fellows, 20 Members, 5 Associates, 3 Students, and 34 Visitors, making a total of 126. The President declared the meeting open at 4.05 p.m. OBITUARIES The President: It is my sad duty to announce the death of the following members of the Institute C. Boocock, R. J. G. Moore, M. P. Pearse, and A. I. Sussman, all Fellows, and W. T. Dalling, a Life Member. As a mark of respect to the memory of the deceased and in sympathy with the bereaved, I ask you to rise and observe a few moments' silence. MINUTES Die President: Item twee op die agenda is die bekragtiging van die notules van die jongste Algemene Vergadering van die Instituut. Daar die notules in die Augustus uitgawe van die Joernaal gepubliseer is, vra ek u toestemming dat dit as sulks bekragtig word. Toestemming verleen. WELCOME TO VISITORS The President: It is my very great pleasure to welcome all the distinguished guests who have honoured us with their presence this afternoon; in particular, a hearty word of welcome to the Honorary President of the Institute, Mr Plumbridge, the President of the Chamber of Mines. You are doubly welcome here, sir, and we thank you for your presence. Also to that old member and stalwart, the Honorary Vice-President of the Institute, Mr Tommy Gibbs, the Government Mining Engineer-you're very welcome, Mr Gibbs. Then, we are particularly privileged this afternoon to have an Honorary Member with us, the Minister of Mines for Rhodesia, Mr Dillon. You will recall that he honoured us with his company last year. Mr Dillon, we are very appreciative and hope that this is now a standing arrangement. We are also honoured by the presence of some thirteen Presidents, Vice-Presidents, or Chairmen of our sister scientific and technical organizations. I shall rapidly read their names, but they must all feel assured that they are very welcome here today. Firstly, one of our own Past Presidents and members, Mr Geoff Goode in his capacity as President of the Associated Scientific and Technical Societies of South Africa; Mr L. R. Robinson, President of the South African Institution of Mechanical Engineers, and Mrs Robinson; Mr G. Goedhals, President of the South African Institute of Electrical Engineers ; Dr Antrobus, President of the Geological Society of South Africa, and Mrs Antrobus; Mr T. V. Dean, Vice-President of the Institute of Land Surveyors of the Transvaal, and Mrs Dean; Mr R. M. Stroh, President of the Mine Ventilation Society of South Africa; Mr Ken Steele, President of the Association of Mine Managers, and Mrs Steele; Mr Mike Gericke, President of the South African Council for Professional Engineers; Mr R. G. Matthews, President of the Institute of Mine Surveyors of South Africa; Mr P. H. Pettifor, President of the Institute of Production Engineers, London, and Mrs Pettifor ; Dr Nico Stutterheim, Chairman of the South African Institute of Chemical Engineers, and Mrs Stutterheim; Professor F. A. van Duuren, Chairman of the Engineers' Liaison Committee in Pretoria; also, I haven't spotted him but I trust he is here-Mr Alex Bain, who is Chairman of this Institute's Witbank/Middelburg Branch. To one and all, ladies and gentlemen, a hearty word of welcome. Not last on our list, a word of welcome to Mr Eric Boden, the Manager of A.S. and T.S. We also have with us I trust, Dr Deist, and his good lady-Dr Deist will be figuring in our proceedings later this afternoon. Also Mr Barcza and Mrs Barcza. Mr Bareza, a former President of the Institute, also has a task to perform. Then, I hope two of our student prize winners are here-Mr Beetge and Mr Painting. Then we also have Mr Roberts, who is welcome in his capacity as co-author with Dr Deist. Then, last of all, a hearty word of welcome to Dr Helen Glen (I am not sure whether she has arrived yet, but she is certainly due to come)-the new Honorary Editor of the Institute's Journal. MEMBERSHIP The President: I have pleasure in announcing that, their names having been published in accordance with By-law 5.2.2, the following have been elected by Council to membership in the following grades Fellows: W. G. Jayes and F. K. Wright Members: D. W. Penman, A. W. Bryson, and D. L. Gibbs Graduates: R. J. Adey, J. P. Bond, R. C. Dunne, G. M. Entwhistle, J. M. Rendu, J. P. S. Turner, and A. P. van Jaarsveld Associates: A. Ellis, B. R. Hambly, A. J. Johansen, and G. W. Tregoning
Jan 10, 1973
-
The South African Institute of Mining and Metallurgy Information on Membership (48072348-16b1-4c9e-886f-e15ad775c801)
The Institute was founded in 1894 as the Chemical and Metallurgical Society of South Africa. In 1904 it was reconstituted as the Chemical Metallurgical and Mining Society of South Africa and in 1956 it became the South African Institute of Mining and Metallurgy. The objects of the Institute are to advance the science and practice of mining and metallurgy, to afford opportunities for the interchange and recording of knowledge of mining and metallurgy and to ensure high standards of professional conduct and competence. Membership benefits include monthly issues of the Journal of the Institute, monthly General Meetings at which papers are read, symposia, excursions to mining and industrial concerns and the use of club facilities at Kelvin House. Technical journals received on an exchange basis are available to members at the Johannesburg Public Library. The current membership of the Institute is over 1,400. Membership applications are accepted from suitably qualified persons and the requirements for entrance to the various grades of membership are summarised below. Members shall be not be less than 30 years of age, shall be university graduates in pure or applied science or shall produce evidence to the satisfaction of the Council that they have successfully completed a co-ordinated course of study in pure or applied science of at least three years' duration at an approved university or institution deemed by the Council to be of equivalent status. Members shall have been employed in senior technical positions in important mining or metallurgical undertakings for at least five years or they shall have practised as mining or metallurgical consultants for at least five years. They shall be practising their profession at the time of application. Entrance fee R4.00; Annual subscription R14.00 (town), R12.00 (country). Letters of designation: M.S.A.INST.M.M. Associate Members shall be not less than 25 years of age and shall be university graduates in pure or applied science, or shall have successfully completed co-ordinated courses of study in pure or applied science of at least three years' duration. They shall have been engaged in work of an approved technical character in the mining or metallurgical industries, of which not less than two years shall have been in positions of responsibility. A candidate shall be practising his profession at the time of his application. Entrance fee R2.00; Annual subscription R12.00 (town), R10.00 (country). Letters of designation: A.M.S.INST.M.M. Affiliates shall be not less than twenty-five years of age, and shall have been engaged in positions of responsibility in, or associated with, the mining or metallurgical industries for periods of not less than three years. If, however, the candidate for admission to the higher grade of Affiliate, is at the time of his application, already a Student member, he need satisfy the Council only that he is, at the time of his application, engaged in a position of responsibility in or associated with the mining or metallurgical industries. In all cases the applicants shall satisfy the Council that they are fit and proper persons to become Affiliates. Entrance fee R2.00; Annual subscription R12.00 (town), R10.00(country). Graduate Members shall be not less than 21 years of age and shall be university graduates in pure or applied science, or have completed co-ordinated courses of study in pure or applied science of at least three years' duration at an approved university or institution. They shall not remain Graduate members after attaining the age of 30 years without the persmission of Council. Entrance fee R1.00; Annual subscription R7.00 (town), R6.00 (country). Students shall be persons not less than 18 years of age who are being educated or trained in a manner approved by the Council, to occupy a technical position in or associated with the mining or metallurgical industries and who, furthermore, shall not have attained the qualification required for a higher grade of membership. They may remain Students until they have obtained the necessary qualifications for transfer to a higher grade of membership, but not after the end of the Institute's financial year in which the attain the age of 28 (twenty-eight) years. They shall then transfer to a higher grade to retain membership of the Institute. The Council may relax the provisions of this clause in such cases as it considers appropriate. Entrance fee nil; Annual subscription R3.00 (town), R3.00 (country). Other. The Council has the power to elect to the grade of Member or Associate Member candidates who may not fulfil all the requirements for entrance to these grades but whose status, professional achievements and practical experience in mining or metallurgy justify such election. Applications. Requests for membership application forms should be addressed to the Secretary: South African Institute of Mining and Metallurgy, p.a. Box 1183, Johannesburg.
-
The South African Institute of Mining and Metallurgy Information on Membership
The Institute was founded in 1894 as the Chemical and Metallurgical Society of South Africa. In 1904 it was reconstituted as the Chemical Metallurgical and Mining Society of South Africa and in 1956 it became the South African Institute of Mining and Metallurgy. The objects of the Institute are to advance the science and practice of mining and metallurgy, to afford opportunities for the interchange and recording of knowledge of mining and metallurgy and to ensure high standards of professional conduct and competence. Membership benefits include monthly issues of the Journal of the Institute, monthly General Meetings at which papers are read, symposia, excursions to mining and industrial concerns and the use of club facilities at Kelvin House. Technical journals received on an exchange basis are available to members at the Johannesburg Public Library. The current membership of the Institute is over 1,400. Membership applications are accepted from suitably qualified persons and the requirements for entrance to the various grades of membership are summarised below. Members shall be not be less than 30 years of age, shall be university graduates in pure or applied science or shall produce evidence to the satisfaction of the Council that they have successfully completed a co-ordinated course of study in pure or applied science of at least three years' duration at an approved university or institution deemed by the Council to be of equivalent status. Members shall have been employed in senior technical positions in important mining or metallurgical undertakings for at least five years or they shall have practised as mining or metallurgical consultants for at least five years. They shall be practising their profession at the time of application. Entrance fee R4.00; Annual subscription R14.00 (town), R12.00 (country). Letters of designation: M.S.A.INST.M.M. Associate Members shall be not less than 25 years of age and shall be university graduates in pure or applied science, or shall have successfully completed co-ordinated courses of study in pure or applied science of at least three years' duration. They shall have been engaged in work of an approved technical character in the mining or metallurgical industries, of which not less than two years shall have been in positions of responsibility. A candidate shall be practising his profession at the time of his application. Entrance fee R2.00; Annual subscription R12.00 (town), R10.00 (country). Letters of designation: A.M.S.INST.M.M. Affiliates shall be not less than twenty-five years of age, and shall have been engaged in positions of responsibility in, or associated with, the mining or metallurgical industries for periods of not less than three years. If, however, the candidate for admission to the higher grade of Affiliate, is at the time of his application, already a Student member, he need satisfy the Council only that he is, at the time of his application, engaged in a position of responsibility in or associated with the mining or metallurgical industries. In all cases the applicants shall satisfy the Council that they are fit and proper persons to become Affiliates. Entrance fee R2.00; Annual subscription R12.00 (town), R10.00(country). Graduate Members shall be not less than 21 years of age and shall be university graduates in pure or applied science, or have completed co-ordinated courses of study in pure or applied science of at least three years' duration at an approved university or institution. They shall not remain Graduate members after attaining the age of 30 years without the persmission of Council. Entrance fee Rl.00; Annual subscription R7.00 (town), R6.00 (country). Students shall be persons not less than 18 years of age who are being educated or trained in a manner approved by the Council, to occupy a technical position in or associated with the mining or metallurgical industries and who, furthermore, shall not have attained the qualification required for a higher grade of membership. They may remain Students until they have obtained the necessary qualifications for transfer to a higher grade of membership, but not after the end of the Institute's financial year in which the attain the age of 28 (twenty-eight) years. They shall then transfer to a higher grade to retain membership of the Institute. The Council may relax the provisions of this clause in such cases as it considers appropriate. Entrance fee nil; Annual subscription R3.00 (town), R3.00 (country). Other. The Council has the power to elect to the grade of Member or Associate Member candidates who may not fulfil all the requirements for entrance to these grades but whose status, professional achievements and practical experience in mining or metallurgy justify such election. Applications. Requests for membership application forms should be addressed to the Secretary: South African Institute of Mining and Metallurgy, P.D. Box 1183, Johannesburg.
-
The South African Institute of Mining and Metallurgy Information on Membership (aafb495f-80a7-44c6-a889-1f81cfab5cd5)
The Institute was founded in 1894 as the Chemical and Metallurgical Society of South Africa. In 1904 it was reconstituted as the Chemical Metallurgical and Mining Society of South Africa and in 1956 it became the South African Institute of Mining and Metallurgy. The objects of the Institute are to advance the science and practice of mining and metallurgy, to afford opportunities for the interchange and recording of knowledge of mining and metallurgy and to ensure high standards of professional conduct and competence. Membership benefits include monthly issues of the Journal of the Institute, monthly General Meetings at which papers are read, symposia, excursions to mining and industrial concerns and the use of club facilities at Kelvin House. Technical journals received on an exchange basis are available to members at the Johannesburg Public Library. The current membership of the Institute is over 1,400. Membership applications are accepted from suitably qualified persons and the requirements for entrance to the various grades of membership are summarised below. Members shall be not be less than 30 years of age, shall be university graduates in pure or applied science or shall produce evidence to the satisfaction of the Council that they have successfully completed a co-ordinated course of study in pure or applied science of at least three years' duration at an approved university or institution deemed by the Council to be of equivalent status. Members shall have been employed in senior technical positions in important mining or metallurgical undertakings for at least five years or they shall have practised as mining or metallurgical consultants for at least five years. They shall be practising their profession at the time of application. Entrance fee R4.00; Annual subscription R14.00 (town), R12.00 (country). Letters of designation: M.S.A.INST.M.M. Associate Members shall be not less than 25 years of age and shall be university graduates in pure or applied science, or shall have successfully completed co-ordinated courses of study in pure or applied science of at least three years' duration. They shall have been engaged in work of an approved technical character in the mining or metallurgical industries, of which not less than two years shall have been in positions of responsibility. A candidate shall be practising his profession at the time of his application. Entrance fee R2.00; Annual subscription R12.00 (town), R10.00(country). Letters of designation: A.M.S.INST.M.M. Affiliates shall be not less than twenty-five years of age, and shall have been engaged in positions of responsibility in, or associated with, the mining or metallurgical industries for periods of not less than three years. If, however, the candidate for admission to the higher grade of Affiliate, is at the time of his application, already a Student member, he need satisfy the Council only that he is, at the time of his application, engaged in a position of responsibility in or associated with the mining or metallurgical industries. In all cases the applicants shall satisfy the Council that they are fit and proper persons to become Affiliates. Entrance fee R2.00; Annual subscription R12.00 (town), R10.00(country). Graduate Members shall be not less than 21 years of age and shall be university graduates in pure or applied science, or have completed co-ordinated courses of study in pure or applied science of at least three years' duration at an approved university or institution. They shall not remain Graduate members after attaining the age of 30 years without the permission of Council. Entrance fee R1.00; Annual subscription R7.00 (town), R6.00 (country). Students shall be persons not less than 18 years of age who are being educated or trained in a manner approved by the Council, to occupy a technical position in or associated with the mining or metallurgical industries and who, furthermore, shall not have attained the qualification required for a higher grade of membership. They may remain Students until they have obtained the necessary qualifications for transfer to a higher grade of membership, but not after the end of the Institute's financial year in which they attain the age of 28 (twenty-eight) years. They shall then transfer to a higher grade to retain membership of the Institute. The Council may relax the provisions of this clause in such cases as it considers appropriate. Entrance fee nil; Annual subscription R3.00 (town), R3.00 (country). Other. The Council has the power to elect to the grade of Member or Associate Member candidates who may not fulfil all the requirements for entrance to these grades but whose status, professional achievements and practical experience in mining or metallurgy justify such election. Applications. Requests for membership application forms should be addressed to the Secretary: South African Institute of Mining and Metallurgy, P.D. Box 1183, Johannesburg.
-
Colloquium and General Meeting
Colloquium and General Meeting were held at Kelvin House on 19th May, 1971, the theme being 'Modern trends in coal mining practice.' Mr V. C. Robinson (President) was in the Chair. The Colloquium was attended by 205 delegates and was opened by the President at 9 a.m. OBITUARY The President: 'It is my sad duty to announce the death of C. C. Cullen, Fellow, who joined the Institute in 1946 and passed away on 15th March, 1971. As a mark of respect to the memory of the deceased and in sympathy with the bereaved I would ask you all to rise and observe a few moments silence'. ELECTION OF SCRUTINEERS The President: 'In terms of Clause 9.4 of the By-Laws I now call for the nomination of seven Corporate Members to act as scrutineers of the ballot for Council'. Messrs V. C. Robinson, Prof D. D. Howat, Dr J P Hugo, D. G. Maxwell, J. K. E. Douglas, R. J. Adamson and P. Lambooy were nominated by P. W. J. van Rensburg and seconded by P. A. von Wietligh. The President: 'Are there any further nominations? If not I declare these gentlemen elected.' MEMBERSHIP The President: 'I have much pleasure in announcing that the names of candidates, having been published in accordance with By-Law 5.2.2, Council has elected them to membership of the Institute in the following grades: Members: Douglas Edward King, Bryan Rudolph Scott, James Gregor Phimister, Anthony David Walters. Graduates: Cornelius Johann Muller, Marthinus Stephanus Mulder. Associates: John George Everson, Colin Robert Llewellyn Davies. Students: Francois George Enslin Beetge, Ewald Boshoff, Christiaan J. Cloete, Christopher John Davies, Cameron George Elvin, Kenneth Eric Field, Johannes Louis Fourie, Hans Gert Gastrow, Peter John Ledger, James Robert William Lindsay, Kynaston Lloyd McDonald, Richard Peter Mohring, Arthur Leslie Painting, Matthias Arthur Pascall, Ian Neil Sinclair, Donald Allan James Ross-Watt. MEMBERS TRANSFERRED TO A HIGHER GRADE From Member to Fellow: Peter Norman Roberts. From Associate to Graduate: Alfred Eric WaIter Fletcher. From Student to Graduate: Wilfried Pierre de Villiers, Edward Emile Eichenberger, William Alan Nairn, Lodewyk Johannes de Jager, Colin Henry Obray, John Grenig Rees. COLLOQUIUM The President opened the proceedings and introduced Mr N. W. S. Schumann as the overall chairman for the day. The following papers and contributions were presented: FIRST SESSION: Chairman R. C. J. GOODE. Paper: 'Problems encountered in the operation of a new colliery' by P. M. C. Wilson and A. A. Oakes. Contributors: D. J. Moloney, G. R. Canny, I. G. Evans, R. B. MacGillivray, Dr F. G. J. de Jager, M. J. Deats, and N. Zolezzi. R. B. MacGillivray Mr President and gentlemen, I would like to congratulate the authors on presenting a most interesting paper on a very important subject. After several attempts at finding suitable reserves to extend the life of Welgedacht Exploration Company's Utrecht Colliery a block of coal rights was acquired south west of the town of Utrecht. A study of these reserves showed that they would enable a satisfactory return on capital invested to be achieved. It was decided therefore to open up what is now called the Zimbutu section of Welgedacht Exploration Company, to produce 41 000 metric tons of coal per month. The decision to open this section was taken in August, 1968 and due to certain allocation requirements it was necessary to bring it into production by the 1st of January, 1970. Fortunately a fair amount of statistical data had been collected prior to August, 1968 from the old Utrecht Colliery in anticipation of opening a mine and a fairly detailed rechnical report had been prepared. As a result the dead line was only missed by four days. Main features of the Design A feasibility study was carried out on three possible shaft positions and the final position was selected from these three on economic grounds. As the coal seam at the selected shaft position was only 21 metres below the surface it was decided to sink two twin incline shafts to enable rapid establishment of through ventilation and alternative hauling arrangements for quick development. This also allowed the final vertical ventilation shaft to be placed at some distance away to avoid the nuisance of fan noise. Second outlet requirements are also very well met by these twin inclines. Again on the basis of economics and also due to the uncertainty of roof conditions it was decided to use hand loading methods underground. However, to allow for future possible conversion to mechanised loading, should this become economical through rising wages, a conveyor belt was installed in the hauling shaft. This conveyor belt is fed from an endless rope haulage in the east companion by means of tipplers, a bin and a feeder. The main development heading was left clear for the future installation of a conveyor belt which would afford easy conversion to mechanisation.
-
Colloquium and General Meeting
A Colloquium and General Meeting was held jointly with the Mine Ventilation Society of S.A. in Kelvin House, Johannesburg, on 17th November, 1971, the theme being "The Economics of Mine Ventilation". Professor D. Howat (President) was in the chair. The Colloquium was attended by 150 delegates and was opened by the President at 9.00 a.m. MEMBERSHIP The President: "I have much pleasure in announcing that the names of the candidates, having been published in accordance with By-Law 5.2.2, Council has elected them to membership of the Institute in the following Grades: Fellows: Frederich-Wilhelm Volk, Peter Bennet Columbine. Members: Allan Colin Lawrence, Karel Anton van Gessel, Christopher Robert Harrison, Christopher Michael George Wartley, Frank Heinrich Deist, Ralph Morris, Benjamin Johannes Nolte. Associates: Wolf gang Freidrich Gottsman. TRANSFERS From Member to Fellow: Hugh Edward Keith Alien. From Graduate to Member: Errol Vincent Bosman, Christopher Roderick Stewart Needes, Bernard Wessels Holthousen. From Student to Graduate: David Robert Fleming. I welcome the new members to the Institute and congratulate them on their election. CO-OPTION TO COUNCIL The President announced that at the Council meeting held on 5th October, 1971, it was agreed, in terms of Rule 3.9 to co-opt Dr T. B. Beeton to Council. COLLOQUIUM The President welcomed visitors and members. He stressed that the discussion would be informal and that any contributor requiring publication should submit his contribution in writing. He then thanked the authors for providing pre-prints of the papers. After the President had concluded his opening remarks, he asked Professor J. de V. Lambrechts to act as Colloquium Chairman for the day and he, in turn, introduced the three Session Chairmen namely, Dr A. Whillier (Chamber of Mines and President of the Mine Ventilation Society); Mr M. Barcza (Managing Director, Corner House Laboratories); and Mr L. W. P. v.d. Bosch (Chief Consulting Engineer, Union Corporation). The following papers were presented: "Fan efficiency investigation on mines of the Union Corporation, Ltd." by J. A. Drummond. Published in the Journal Feb. 1972. "The design of underground cooling towers" by A. Whilliel'. Published in the Journal, Oct. 1971. "Some aspects of the design of cooling plant installations" by R. Hemp. Published in the Journal, Nov. 1971. "The planning of ventilation and refrigeration requirements in deep mines" by D. F. H. Grave and R. M. Stroh. Published in the Journal, Dec. 1971. "Cooling power of underground environments" by D. Mitchell and A. Whillier. Published in the Journal, Oct. 1971. At the conclusion of the three technical sessions the Symposium Chairman commented as follows, indicating that he would prepare a written summing up at a later stage: "The tone of the colloquium has had a sincerely practical note about it. It would have been a pity if the ventilation experts talked only theory and little practice. This practical theme has, I am sure, made the colloquium interesting to both ventilation men and others whose daily tasks do not touch so closely on this fascinating subject. This practical theme was in evidence through all the papers and contributions. Some of you may have felt that there was not enough emphasis on the word 'economics' as advertised in the broad title of the colloquium. I do not think this was really a valid criticism because as someone said 'it all boils down to Rands in the end!' So whether it was a case of low fan efficiency, poor design of cooling towers, wrong planning or low human efficiency due to high heat stress. . . it all boils down to money saving and therefore economics, whenever improvements are forthcoming. The title of the colloquium was thus not misplaced. The views of senior mining men on the production side are appreciated. Let us say that this exchange of views between ventilation engineers and those who have to take the final decisions and spend the money, should prove to be most rewarding." Professor Lambrechts finally thanked the Session Chairmen and everybody who had helped to make the colloquium a success and the meeting closed at 4.0 p.m. In a subsequent written summing up, the Colloquium Chairman gave the following as his impressions of some of the highlights which emerged from the papers and discussion thereof: (The names indicate the authors only). Drummond: It was hinted that the time had arrived to consider the introduction of a South African fan test code which would be better suited to local conditions than the currently acknowledged B.S.S. code which, however, is seldom enforceable in practice. In this connection also, there was prominent reference to the thermodynamic approach of McPherson. Wide variations in the quality of maintenance of, and repair work on, fans were stressed. It was mooted that ventilation engineers responsible for estimating the basic duty specifications for large fans, frequently played safe by overestimating the pressure required, thus ensuring that there would not be a shortfall in air volume delivered. This usually meant reduced fan efficiency and it was suggested that decision makers seemed to lay more emphasis on volume of air delivered than on real eco-
-
10th International Symposium on the Application of Computer Methods in the Mining Industry
To be held from the 9th to 14th April, 1972, in Johannesburg, South Africa. GENERAL INFORMATION The first symposium in the series was staged by the University of Arizona in 1961. Since then Stanford University, Colorado School of Mines, Pennsylvania State University and the Society of Mining Engineers of the American Institute of Mining, Metallurgical and Petroleum Engineers have acted together with the University of Arizona as co-sponsors of the series. The 9th Symposium in 1970 was sponsored by the Canadian Institute of Mining and Metallurgy together with McGill University and Ecole Poly technique in Montreal. The 10th Symposium, the first to be held outside the North American continent, is being organised by the South African Institute of Mining and Metallurgy (with the Council for Scientific and Industrial Research and the South African Council for Automation and Computation) in close collaboration with the previous co-sponsors. OBJECTIVES Mineral ventures increase in scale and complexity. The planning and control of these projects requires more and more sophisticated techniques. The intention of the symposium is to pool and exchange experience and knowledge and also to discuss new and potential developments. The papers presented in the main sessions, which will extend over one week, will together indicate progress which has been made in the successful application of operations research, mathematical, statistical and computer methods in each of the various aspects of operation in the mineral industry. A coherent account will be developed by consideration, in consecutive sessions, of the stages through which mineral prospects evolve in the course of their life. Primary aims are thus to stimulate discussion in depth of previous applications, to highlight current trends and to provide guidelines for future developments. PARTICIPATION The intention is to bring together persons responsible for managing the various operations in the mineral industry and the workers engaged in the development of mathematical and computer methods relevant thereto. SYMPOSIUM TOPICS 1. Market Analysis-demand and supply trends, models of mineral markets, price prediction. 2. Exploration and ore reserve estimation--exploration strategies, choice of drilling and sampling patterns, quantification of geological information, geo-statistical analysis, ore reserve assessment. Storage and retrieval of associated data. 3. Project design and analysis-influence on viability and risk of capitalisation, scale and method of operation, processing, uncertainties in design premises. 4. Planning of operation-planning and scheduling of construction, of development and of depletion of ore reserves. Logistics, rock mechanics and ventilation. 5. Control of operations-financial, production, cost and quality control as applied to both mining and processing. Flow and processing of relevant information. CALL FOR PAPERS An invitation is extended to intending authors to submit a synopsis, in 200 to 300 words, of papers which would develop the themes outlined above. The Programme Sub-Committee will choose, on the basis of these synopses, some 20 to 30 authors who will be invited to submit papers. Selection will be aimed at the provision of a coherent structure. Other authors may be invited to submit short papers either as contributions to the primary papers or for brief discussion in ancillary sessions which will be scheduled to follow on the main sessions. The official language of the symposium will be English. DEADLINES Prospective authors must submit synopses of papers by ............end April, 1971 Authors will be informed of results of selection of papers by . . . . . . . end June, 1971 Manuscripts will have to be in the hands of the Editors by . . . . . . . . . end October, 1971 PRE-PRINTS Papers selected for presentation in the main sessions will all be pre-printed and distributed prior to the symposium. As many as possible of the shorter papers and prepared contributions will also be pre-printed. PROCEEDINGS All of the main and ancillary papers together with edited discussion will be published shortly after the symposium in a single volume. TOURS AND VISITS A choice of visits to relevant local undertakings on a day during the course of the symposium will be available to participants. These will include a deep level gold mine. A tour which will include mineral projects of interest and the Kruger National Game Park will be arranged in the week following the symposium. LADIES' PROGRAMME Arrangements will be made for the reception and entertainment of ladies. ACCOMMODATION Accommodation will be available at hotels convenient to the symposium venue. The cost of reasonable hotel accommodation in Johannesburg is in the range R5 to RIO (7 to 14 U.S. dollars) per person per night. All reservations and associated arrangements may be made through agents to be appointed by the organisers in due course. FEES AND COSTS Symposium fees will not exceed R70 (100 U.S. dollars). These will include registration, one copy of the published proceedings, a set of pre-prints of the main papers, teas and lunches during the course of the symposium, and the various official social events as well as the mid-week visits. Accommodation, travel and post-symposium tour charges are not included in this figure. FURTHER INFORMATION All communications should be addressed to: The Secretary, South African Institute of Mining and Metallurgy, Kelvin House, Hollard Street, Johannesburg, South Africa.