Search Documents

By R. C. Urquhart, D. D. Howat, R. I. L. Guthrie

Heat losses from ladles during teeming by R. C. URQUHART, M.Eng. (McGiII), Ph.D. (Visitor). R. I. L. GUTHRIE, B.Sc. (Eng.) (London), A.R.S.M., Ph.D., D.I.C. (Visitor), and D. D. HOWAT, B.Sc. (Glas.), Ph.D. (Fellow) In an investigation of the loss of temperature by liquid steel during a teeming operation, a numerical technique was used to calculate the heat flows and the rate of temperature drop over the entire teeming operation. The calculations show that, before teeming, approximately 50 per cent of the heat loss is into the ladle wall at the level of the metal. As teeming progresses, the amount of heat lost by radiation to the wall above the metalline increases. The effect of variables, such as initial metal temperature, the preheat of the ladle and ladle cover, and delays, on the rate of temperature loss by the metal were determined.

Jan 11, 1973

Book review HOEK, E., and BRAY, J. Rockslope engineering. London, The Institution of Mining and Metallurgy, 1974. £5. NIM reports Report no. 1625 The determination of uranium and thorium by the use of delayed neutrons. Report no. 1626 Formation constants of zinc chlorocomplexes in perchlorate medium. Report no. 1629 The thermodynamics of the formation of complexes of silver with some substituted pyridines. Report no. 1630 An electrochemical investigation of the dissolution of copper, nickel, and copper-nickel alloys in ammonium carbonate solutions. Report no. 1640 A semi-automatic titrimeter for cyanide analyses. Report no. 1644 Prospects for the recovery of minerals from the sea. 1974 A.S. & T.S. National Award Professor D. C. Midgley, President of the Associated Scientific and Technical Societies of South Africa, today announced the winner of the 1974 A.S. & T.S. National Award. 1974 G.W. en T.V. Nasionale Toekenning Professor D. C. Midgley, President van die Geassosieerde Wetenskaplike en Tegniese Verenigings van Suid- Afrika het vandag die wenner van die 1974 G.W. & T.V. Nasionale Toekenning aangekondig.

Jan 9, 1974

The comments by Mr Chaston were constructive and much appreciated. Considering firstly the recovery of cassiterite from fine deslimed material. A size distribution analysis shows that 58 per cent of cassiterite in Union Tin flotation concentrate reports in the minus 15 micron (quartz) size range. This is achieved at a recovery of 67 per cent and concentrate grade of 42,6 per cent. It is of interest to note that at Altenberg in East Germany 85 per cent of the tin in deslimed minus 43 micron material is recovered into a 14 to 16 per cent Sn concentrate using para-tolyl arsonic acid as collector. Reconcentration of this material is then carried out using two shaking table stages which recover 53 per cent of the tin in a 50 per cent Sn concentrate. Flotation was resorted to after recovery rates of 35 per cent and concentrate grade of 30 per cent had been achieved in a 275 ton per day plant comprising 130 tables. Tests on tabling of deslimed minus 43 micron material have not been carried out at Union Tin. The cost of equipment actually associated with cassiterite flotation amounts to about R60 000. The

By S. K. De Kok

Over a period of three years, since samples first became available, laboratory and pilot plant experiments have been conducted to develop a method of treatment to recover copper and zinc in saleable grades of concentrates from the Prieska complex sulphide orebody. These experiments have been based on adaptations of principles investigated by research workers and applied to similar ore types throughout the world. The differential flotation process finally worked out involves a comparatively coarse grind, flotation of the copper at near-neutral pH with the use of a zinc-cyande sphalerite depressant, followed by flotation of the reactivated sphalerite. This procedure has had such success that the construction of a full-scale plant is proceeding with confidence that the small-scale operations will be duplicated or improved upon. It is to be expected that the large plant will follow the pattern of almost every flotation plant that has been built in that modifications to the circuitry and reagent systems will be made as experience is gained.

By J. Preussner, U. Glatzel, R. Völkl, S. Prins, M. Wenderoth

Platinum base alloys are very corrosion resistant and have got a high melting point. Similar to Ni-base superalloys, which are used for jet turbines, the hardening effect of the intermetallic L12Pt3Al phase is used to receive a material that is creep resistant at high temperatures. Chromium is added to the alloy system to stabilize the L12phase down to room temperature. With the right amount of nickel the misfit and shape of the precipitates can be controlled. Various alloy compositions have been melted and analysed. With scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS) a microstructure can be observed, which is very similar to the one in Ni-base superalloys. To support alloy development with simulations, a thermodynamic database of the Pt-Al-Cr-Ni system is about to be established. The SEM and EDS measurements provide useful input to the thermodynamic optimization. Also many data from the literature have been used to receive the best approximation. The Cr-Pt binary phase diagram has been reassessed and the latest results of thermodynamic modelling are presented.

Jan 1, 2006

By D. M. Meyer, K. Auerswald

The production of electrolytic manganese in South Africa by M. HARRIS, Pr. Eng., B.Se. (Eng.) (Fellow), D. M. MEYER, Pr. Eng., B.Se. (Meeh. Eng.) (Visitor), and K. AUERSWALD (Visitor) The decision to construct the first electrolytic manganese plant in South Africa was important and farreaching. After evaluating the results of the pilot plant operation, the first South African producer, Electrolytic Metal Corporation (Emcor), established a plant in Krugersdorp. Initially, there were many process problems that had to be InvestIgated, and, after these had been solved and many operating parameters had been established, manganese was successfully produced. When the Delta Manganese plant in Nelspruit was planned, cognizance was taken of the fact that, if peak efficiencies were to be maintained, the process must be operated between fairly narrow parameters. Instrumentation was therefore installed to control the process automatically wherever possible. The main features of the Delta Manganese operation are outlined, with a brief description of each stage of the process from ore milling through to electrowinning and packing of the metal. It is concluded that much benefit can be obtained from further research work into process improvements and into the exact effect of certain variables on plant and current efficiency.

Jan 2, 1977

Review Mining annual review June 1979. London, Mining Journal, 1979. 624 pp. Available as part of the subscription to the Mining Journal or at £12,50 per copy. This annual review is recognized internationally as the world leader in reporting on metals and minerals, and is eagerly awaited each year for its authoritative content, which is compiled by well-respected experts throughout the world.

Jan 1, 1979

By B. J. Madden

The formula developed by Salamon and Munro in 1967 has been used for the past 22 years in the design of bord-and-pillar workings in South African collieries. This paper re-assesses the formula In the light of Its past performance and examines the effect of mining method on coal-pillar strength. An account is given of the extension of the formula so that it can be applied beyond the empirical range for which it was derived, and the advantages of the extended formula (the squat-pillar formula) are described.

Jan 1, 1991

By C Smit

SYNOPSIS A prototype collimated radiometric face scanner was tested in the Harmony Gold Mine. The results obtained during the pilot study indicate that in situ radiometric uranium assays are statistically indistinguishable from those obtained conventionally from channel chip samples. In addition, the study demonstrated that reasonably reliable gold estimates can be deduced from the radiometric measurements, by use of the ratio of gold to uranium within a mine. The instrumentation, calibration procedures, and background determination are described briefly.

Jan 1, 1985

By B. K. Cross

This paper, which adopts a philosophical approach, attempts to analyse the contribution that the computer is capable of making in geological analysis, financial evaluation, and mine project control. Also examined are some reasons for non-utilization of these capabilities. As with most computer associated problems, the cause is primarily human and not mechanical. The paper gives one numerical example of the analysis of geological data and one of the evaluation of mine-design data. The values used in the examples are intended only to emphasize certain points and are not necessarily reproducible.

Jan 1, 1980

By H. A. D. Kirsten

SYNOPSIS This paper describes simple calculations to evaluate the stability of hangingwall and footwall strata at the work¬ing face and in backfilled areas. It shows that the benefits of support provided by backfill can best be realized when the fill is placed as close to the face as possible. The main beneficial effects of fill are that it reduces the stope span, at the same time providing a damping effect on vibrations, and prevents the fall-out of blocks in filled areas, thus maintaining the competence of the strata.

Jan 1, 1988

By H. Ruthert

An understanding of wear in systems conveying solids is extremely important from the standpoints of design and economics. The lifetime of any bulk solids-handling system depends on the type of solids present and the operating parameters of the transportation system. The relationship between wear in backfill pipelines on South African gold mines and the transportation system's operating parameters is well understood. However, the effect of the transported solids on the pipe wear is less well understood, because of an inability to characterize particle sharpness. The sharpness of the particles, together with their size and hardness, is responsible for the aggressivity of particles, or their ability to cause damage and wear. This paper presents a novel method for the characterization of particle sharpness. The results presented rank particles according to the sharpness of their surfaces.

Jan 1, 1993

By F. T. Cawood, T. Chikande, H. R. Phillips

Underground mines require electricity to operate both the main surface fans and auxiliary systems, with primary ventilation systems typically accounting for approximately 40–60% of the mine’s overall electricity consumption. The primary reason for this considerable expense is that most underground ventilation systems are designed for peak demand, regardless of the actual demand, which is commonly dictated by diesel equipment usage in trackless mining operations. Most platinum mines on the Great Dyke in Zimbabwe tend to operate their ventilation systems at this peak level, despite the mine’s air quantity being well in excess of the ‘true’ ventilation needs. This is due to a lack of appropriate ventilation controls. The authors designed and installed a ventilation-on-demand system at one of the bord and pillar platinum mines to minimize the use of redundant air in underground operations. Fourth industrial revolution techniques were applied to the environmental monitoring and tracking systems thereby optimizing air quantity demands. The mine managed to reduce its annual power consumption by 23% through the implementation of manual control and time-of-day scheduling levels of the ventilationon- demand concept. There was also a 6% productivity improvement, mainly attributable to an increased face time as a result of the significant reduction in the re-entry period following a blast. This paper introduces a novel concept of ventilation optimization through digital transformation targeting mainly room and pillar platinum mines. A system was designed, installed, and commissioned, though there is currently an ongoing optimization process to harness the full benefits such as productivity enhancement, reduced power costs, and improved worker health.

Dec 13, 2022

By A. M. F. Carter

A survey was conducted so that the degree of corrosive, erosive, and abrasive attack on material-handling systems in the mining and mineral-processing industry could be assessed, and so that the areas of research and development that would be relevant to the needs of the industry could be determined. Of the 59 different mines that were invited to participate in the survey, 41 returned completed questionnaires, giving a return rate of 70 per cent. The total number of completed questionnaires amounted to 45. An analysis of the results shows that attack by erosion or abrasion is considered to occur more often than attack by corrosion. However, al three types of attack must be regarded as significant problems within the mining industry, since 52 per cent of the participating mines reported pump failures due to the inability of the materials of construction to withstand the operating conditions, and almost 90 per cent reported piping failures due to corrosion (22 per cent) or to erosion and abrasion (78 per cent).

Jan 1, 1986

By E. J. Magri

Consideration is given to the problem of the estimation, from limited data, of the likely grade and tonnage for a new mining property that is to be exploited by the selective mining of two metals that have substantial contributions to make to the total revenue. In particular, the case of a new gold and uranium mine in South Africa is analysed as follows. (I) The applicability of the underlying lognormal bivariate model for different support (i.e. ore unit) sizes is examined. (2) The necessary parameters for the bivariate lognormal models for different block sizes are estimated from abundant chipsampling data from a section of the Hartebeestfontein Gold Mine using alternative approaches, and the results are compared. (3) A method is given for obtaining the necessary parameters for a tonnage-grade relationship relative to a joint pay limit from the very limited information likely to be available at the end of the exploration stage of a gold mine, and the results are compared with those obtained from the large volume of data available from a minedout area.

Jan 1, 1982

By F. H. Guise-Brown

Raise-boring experiences in the gold mines of the Anglo American Corporation Group by J. W. WILSON and P. C. GRAHAM Published in the Journal, October, 1972. Discussion by F. H. Guise-Brown., B.Sc. (Min. Eng.) (Member) INTRODUCTION Messrs J. W. Wilson and P. C. Graham are to be congratulated on an excellent paper containing several thought-provoking remarks. The concept of allocating a machine and equipment valued initially at some R300 000 on an experimental basis is courageous, and the results obtained could be of interest to the mining industry as a whole. The Gold Fields of S.A. Group approached this problem differently. In pioneering the start of this work in South African gold mines, they considered that expenditure of this magnitude would be warranted only if the proposition was viable right from the start. To this end, a Robbins R41 was purchased expressly to assist in the duplication of part of the No. 1 shaft system of the Doomfontein Gold Mine. Mr M. J. Koortsl has summed up the initial results of this work and given some preliminary costing, but inflation since that period has made these figures somewhat out of date.

Jan 10, 1972

By V. L. Nkuna, S. R. Amos, T. Naidoo

"Ivanhoe Mines’ Kamoa copper project is a recently discovered high-grade copper sulphide deposit in the Katanga Province of the Democratic Republic of Congo. The mineralization identified to date within the resource is typical of sedimentary-hosted stratiform copper deposits and comprises three distinct units: supergene, mixed, and hypogene mineralization. Since 2010, various metallurgical test work campaigns have been conducted on drill core from different areas within the deposit in line with resource expansion. The most recent bench-scale flotation test work has shown positive repeatable results. The work was conducted on a composite sample of drill core from the southern part of the Kamoa resource. The sample is representative of the first four to five years of planned production, when Ivanhoe Mines intends to produce clean, highgrade copper flotation concentrate. A detailed test work roadmap developed from first principles for the campaign led to an optimum flow sheet for treating the Kamoa mineralization. Copper recoveries of 88.3%, at a concentrate grade of 39.0% copper, were achieved using a composite sample — an improvement on the previously published 85.9% life-of-mine average copper recovery indicated in the November 2013 Kamoa Preliminary Economic Assessment. IntroductionThe Kamoa project is a newly discovered, very large, stratiform copper deposit with adjacent prospective exploration areas within the Central African Copperbelt, approximately 25 km west of the town of Kolwezi in the Democratic Republic of the Congo (DRC) and about 270 kilometres west of the provincial capital of Lubumbashi. Ivanhoe Mines holds its 95% interest in the Kamoa copper project through a subsidiary company, Kamoa Copper SA Limited SPRL, and DRC government owns 5%. The project location is indicated in Figure 1.In January 2013, a new independent mineral resource estimate ranked Kamoa as Africa's largest high-grade copper discovery and the world's largest undeveloped highgrade copper discovery. At this time, Ivanhoe Mines had estimated discovered Indicated Mineral Resources of 739 Mt grading 2.67% copper, containing 43.5 billion pounds of copper, and Inferred Mineral Resources of 227 Mt grading 1.96% copper, containing 9.8 billion pounds of copper, as demonstrated in the Preliminary Economic Assessment (PEA) (AMC, 2013). A 1% copper cut-off grade and a minimum vertical mining thickness of 3 m were applied in each classification."

Jan 1, 2016

By W. F. McKechnie

"Southern Africa is generally thought to be well explored, with only limited potential for major new diamond discoveries. However, Chiadzwa in Zimbabwe and reports of a significant new kimberlite find in Angola are testimony to the dangers attached to an attitude that ‘there is nothing left to find’.Since the major discoveries in the central interior of South Africa in the 1870s, diamond exploration in the region has been led by market and political factors that influence the key exploration drivers of opportunity and value proposition. Unexpected new discoveries by new players always impact on existing producers and, from time to time, denial of opportunity through political or protectionist policies has inhibited investment in exploration.Entrepreneurial exploration appetite in southern Africa will be tempered by the potential value equation and security of investment. Overlaid on this, developments in diamond recovery technologies provide opportunity to reinvigorate current mines and old prospects previously considered too difficult or costly to exploit. Position on the cost curve will remain a key factor for survival in an increasingly competitive environment. IntroductionThe diamond industry in southern Africa boasts a history of 150 years of discovery and mining, forming the cornerstone of development of the core, modern economies at the southern tip of Africa.Since the discovery, in the 1860s and 1870s, of the secondary diamond placers and primary diamond-bearing kimberlite deposits in the central interior of the then Cape Colony and Orange Free State, southern Africa has endured as the pre-eminent diamondproducing region in the world. Notwithstanding periodic competition from significant new discoveries in other parts of the globe and the paucity of recent, new discoveries in the region, its ranking is unlikely to change in the short to medium term.In a geological context the region contains the Kaapvaal-Zimbabwe and Angola-Kasai cratons, identified in terms of Clifford’s rule as areas inherently prospective for diamonds, being underlain by portions of the Earth’s crust that are tectonically stable and older than 1.5 billion years (Clifford, 1992). Although the Democratic Republic of Congo (DRC) would, in a geographic context, be considered to be part of Central Africa, for the purposes of this review it is included in southern Africa since northeast Angola and the adjacent parts of the DRC form part of the same geological terrane and diamond production from both countries needs to be considered together. Historical and current diamond production from the northeastern parts of the DRC around Kisangani is not considered to be significant and its inclusion in the overall numbers for the DRC does not materially affect the overall picture presented here."

Feb 1, 2019

By Allan Jansen, Robin Bissett

[Power-Point Presentation]

Jan 1, 2005

The Annual General Meeting of the Institute was held in Kelvin House, Johannesburg, on Wednesday, August 14th, 1974. Mr P. W. J. van Rensburg (President) was in the Chair. There were present 56 Fellows, 21 Members, 2 Graduates, 5 Associates, 16 Students, and 58 Visitors, making a total of 158. The President declared the Meeting open at 4.08 p.m. OBITUARIES The President: Ladies and gentlemen, before we start the business of the meeting, it is my sad duty to announce the deaths of the following members of the Institute since our last meeting: Dr O. A. E. Jackson, Honorary Life Fellow and Past President; C. Airth, T. L. Blunt, A. E. Frazer, C. L. Lamb, and K. Richardson, Life Fellows; and J. T. Beaumont, Fellow. As you know, there were a number of other deaths during the year, which were reported at previous General Meetings of the Institute. As a mark of respect to the memory of the deceased, and in sympathy with the bereaved, I ask you to rise and observe a few moments' silence. MINUTES The President: Ladies and gentlemen, the next item on your agenda is confirmation of the minutes of the General Meeting and Special General Meeting held on May 22nd, 1974. These will be published in the August issue of the Journal, and, since you have not yet received this, I must ask that they be held over to the next General Meeting. WELCOME The President: It is a very pleasant duty for me to welcome many members of our Institute and our guests, among whom we are particularly pleased to see the President of the Chamber of Mines, Mr Dolf Schumann, who is also Honorary President of this Institute. Mr Schumann, we are extremely pleased to have you with us today. And, we welcome an old friend of ours, Mr Dillon, Minister of Mines in Rhodesia, who has come down for our Annual General Meeting. Mr Dillon, we are very, very pleased to see you here this evening, and we look forward to seeing Mrs Dillon a little later. And we have with us, too, the presidents or representatives of many of our sister and brother associations, institutes, and societies. In particular, we welcome Mr Mike Gericke, President of the South African Council of Professional Engineers, and Professor Midgley, President of A. S. and T. S. We are also pleased to welcome the Presidents of the Mechanical Engineers, Electrical Engineers, Certificated Mechanical and Electrical Engineers, the Civil Engineers, the Joint Council of Scientific Societies, the Mine Ventilation Society, the South African Association of Consulting Engineers, the Association of Mine Managers, the Institute of Foundrymen, the Institute of Welding, the Federation of Societies of Professional Engineers, Mine Surveyors, Production Engineers (London), and the Institute of Production Engineering. We are very glad, too, to have with us a visitor from England, Professor Raynor and Mrs Raynor. Professor Raynor is Professor of Metallurgy at Birmingham University, and a very well-known metallurgist in Britain. We also have with us the Chairman of the Ferro-Alloys Association. We are expecting the Chairman of our Witbank/Middelburg Branch, the Chairman of the Engineers' Liaison Committee, Pretoria, the Director of the Witwatersrand College of Technical Education, and, of course, our old friend, Mr Eric Boden, the Manager of A.S. and T.S. It is a very great pleasure to have with us a number of persons who will receive honorary Life Fellowship at this meeting, and there are some Gold Medal winners and winners of our Student Prizes. We have apologies from a number of people who are away on business, and unfortunately some are ill. But we are extremely pleased to see those of you who are here, and we are also very pleased to see so many ladies. We expect to see many more of them later this evening, at our Cocktail Party. MEMBERSHIP The President: I have pleasure in announcing that, their names having been published in accordance with By-Law 5.2.2., the following have been elected by Council to membership in the following grades Fellows: B. Collins, D. W. Dixon, J. P. Dreyer, A. T. Hudson, and W. W. Pearce. Members: A. T. Fisher and I. F. Nagy. Associate Members : P. D. de Bruyn and H. C. Iverson. Graduates: D. P. O'Shaugnessy and M. F. Sadler. Associates: R. J. Bushell and A. MacDonald. Students : I. J. Barker, P. J. Charter, J. P. de Witt, G. S. Esterhuizen, N. Green, P. M. Jenner, M. J. R. Meyer, A. P. Nicol, W. J. C. Pothas, B. J. Robbetze, N. T. Sutherland, B. A. Statham, C. R. Thomas, N. C. Webb, M. Salamon, R. G. Jurd, and M. McChesney. Transfers to other grades of membership include the following: Member to Fellow: B. W. Holtzhousen. Graduate to Member: T. S. Schultz. Associate to Associate Member: C. L. Jordaan, H. J. L. Tomlinson, J. E. Forbes, G. H. S. Bamford, T. F. Carswell, J. W. Breidenhann, J. R. Garbutt, and L. S. Gibbs. Student to Graduate: C. J. Faueonnier and B. Lund. Student to Associate : G. P. Gooding. We welcome these new members

Jan 10, 1974