Search Documents

By S. Krishnannair

Singular Spectrum Analysis (SSA) is an effective data-adaptive multimodal tool for monitoring chemical processes. However, monitoring multiscale signals using principal component analysis obtained from the multilevel decomposition of process signals using basic SSA assume the upper control limits of monitoring charts (" ) to have a Gaussian distribution. This assumption deteriorates the performance of basic SSA when applied to the monitoring of nonlinear processes. To address the issue in this paper, the kernel density estimation (KDE) was used to estimate upper control limits of monitoring charts for basic SSA based nonlinear process monitoring techniques. The monitoring performance of the resulting basic SSA-KDE approach was then compared with a basic SSA approach of which upper control limits of the monitoring charts were determined based on a Gaussian distribution. Application on nonlinear dynamic simulated process and base metal flotation plant chemical processes showed that the SSA-KDE approach provided better overall performance than the SSA approach with Gaussian assumption-based upper control limits for its monitoring charts. Keywords: Fault detection, singular value decomposition, singular spectrum analysis, kernel density estimation

Jan 1, 2020

By S. Ramatsoma, D. N. C. Phillpotts, B. Whitehead

Changes in flotation performance have been correlated to changes in froth structure, velocity and stability. Literature has shown that when the aeration rate is varied for a specific float cell, the recovery of the valuable mineral reaches a peak which also coincides with a peak in the air recovery – a measure of froth stability. Peak air recovery optimisation methodology is a way to use direct readings of physical phenomena by froth cameras to optimise the metallurgical performance of a flotation plant. The aim of this paper is to show the transient nature of the peak air recovery value and the variety of conditions required to attain the peak air recovery on an industrial flotation plant with tight base-layer control of the feed and internal conditions. Industrial site tests that were conducted under controlled conditions showed different peak values at significantly different corresponding aeration rates during normal operation. The measured peak air recovery points corresponded to maximum PGM recovery during normal flotation, as expected. This dynamic nature of the peak air recovery point conditions has not previously been discussed in literature and indicates the need for online measuring equipment and informs the design of process control algorithms required to exploit the phenomenon for optimisation. Keywords: Froth flotation, flotation control, flotation optimisation, peak air recovery

Jan 1, 2020

By N. Wagner, P. den Hoed, J. D. Steenkamp, S. Soqinase

In pyrometallurgical processes, metal oxides are reduced from molten slag through carbothermic reduction. It is of interest to evaluate the reactivity of the carbonaceous materials towards substances such as slag. Characterization techniques such as coal petrography can provide insight into the influence of feed coal properties and how they potentially dictate reductant performance. This study aimed to compare the petrographically determined organic composition of coal to reductant reactivity. Two South African medium-rank C bituminous coals and one anthracite sample were investigated together with high-carbon ferromanganese industrial slag. The reductant reactivity tests were conducted at 1500°C in a muffle furnace to assess the potential of carbonaceous reductant in reacting with the main slag components. SEM-EDS was applied to understand the extent of MnO (and to a lesser extent, SiO2) reduction from the slag. Coal 2, consisting of a greater proportion of vitrinite (59.5 vol% on a mineral matter-free basis and 54.7 vol% including mineral matter) was the most reactive reductant. The anthracite sample, with the highest inert maceral proportions (71.8 vol% including mineral matter and 76.8 vol% on a mineral matter-free basis), was the least reactive reductant.

Feb 6, 2023

By E. B. Viljoen

I. R. M. Chaston* As a gravity concentration man in the midst of so many eminent flotation experts I feel like Daniel. However, I would respectifully disagree with the opening remarks by Mr Viljoen. First, he suggested that gravity concentration of cassiterite was not effective in sizes below 30 microns. In a paper to the Institution of Mining and Metallurgy in 19621, I gave some figures for gravity concentration of deslimed material both for cassiterite and for wolfram which indicated that careful shaking table concentration of fine deslimed material could give recoveries of 75 to 90 percent in the size ranges above 13 micron. These were figures obtained from normal plant operation. It would be interesting to know if any tests were carried out on gravity concentration of the efficiently deslimed feed to this flotation plant to see what the recovery would be. Secondly, Mr Viljoen suggested that gravity concentration plants were expensive. He gives the cost of a flotation plant at R300 000 to treat a feed of 400 t.p.d. to the desliming section or 160 t.p.d. to the flotation cells. From his operating cost figures it would appear that the flotation cost is approximately R2 to R4 per ton of feed to flotation and the total operating cost about R2 per ton of feed. A table plant to treat this tonnage of deslimed feed would consist of about 30 tables and should cost considerably less to install and very much less to operate than the flotation plant. Third, Mr. Viljoen suggests that the concentrate grade from a gravity concentration operation would be unacceptably low. The paper quoted abovel showed that once a primary fine concentrate had been made, giving a suitably deslimed material, further gravity concentration could give concentrates of over 40 per cent Sn with high recoveries. Tailing from this dressing stage was naturally returned to the feed. To give these high grades, sulphides had been removed by flotation but this necessary flotation step is simple and cheap to operate and could be restricted to the final stage when the quantities involved are small. I would agree that flotation has a part to play in fine tin recovery but this role would only seem to become fully effective at sizes below 10 micron and would seem to require, as Mr. Viljoen has suggested, a mechanism for sizing which is effective down to, say, 1 micron. In the meantime it would be interesting to try tabling the flotation tailing to see if it was possible to recover the plus 20 micron cassiterite which is not recovered well by flotation. One point which has been made during discussion is the suggestion that cassiterite particles have a fully hydrated surface at normal pH. I wonder if this layer could materially affect the overall specific gravity of a very small cassiterite particle and, if so, whether gravity concentration of the very fine cassiterite would be improved if carried out in acid conditions, which would inhibit the formation of this hydrated surface. REFERENCES 1. CHASTON, I. R. M. 'Gravity concentration of fine cassiterite'. Trans. Inst. Min. and Met. Vol. 71, p. 4, 1961 and 1962, and discussion of this paper. Dr. R. P. King Mr Viljoen has drawn attention to the difficulties associated with the presence of very fine particles in the flotation pulp and he has indicated that, on the Union Tin plant, they must sacrifice 30 percent of the cassiterite in the minus 7 /Lm material which they separate and lose. He has also indicated that the rate of flotation of cassiterite remained high at these small sizes. The problem arises because the very small particles stabilize the froth making it impossible to handle. These stable froths cannot be easily broken and therefore cannot be pumped and processed. It seems that further fundamental research work on the properties of stabilized froths is urgently required. We have found another difficulty associated with the presence of very fine particles in phoscorite slurries; these particles can be easily floated but with very poor selectivity. We believe that it is possible that a purely physical mechanism such as entrainment is responsible for the collection of fine particles in the froth. We have also demonstrated that the presence of fine particles in the pulp adversely affects the rate of flotation of the larger particles. For esample, we have found an increase in recovery of + 100 um material from 2 percent to 17 percent in a standard laboratory batch flotation test on phoscorite when the - 37 um was removed from the feed. Such interactions between particles are not universally recognised as an important aspect of the complex flotation mechanism. They should appear in any quantitative formulation of the flotation rate process.

By R. J. Mason

Background to the Transvaal Iron Age-new discoveries at Olifantspoort and Broederstroom R. J. MASON*, Ph.D. (Visitor) The work being done on Iron Age sites in the Transvaal is described, with particular reference to the finds at Olifantspoort and Broederstroom. The material so far found provides evidence for the production of iron and copper, the farming of cattle and sheep, and the construction of large villages by people who were probably ancestral to the present Bantu population. The material dates from as early as A.D. 270, but clear indications occur from AD. 460 onwards.

Jan 1, 1974

By Z. Ruetz

Portable X-ray fluorescence (pXRF) analysis has been widely adopted in the geochemical and environmental field as a cost-saving alternative to standard analyses. This paper outlines the efficacy of a method for indirectly quantifying organic copper content in solvent extraction circuits via stripping of the chelated metal with concentrated sulfuric acid in a single contact and subsequent pXRF aqueous analysis. pXRF analysis is common within the mining industry but presents unique challenges with liquid analysis, the most prevalent of which are briefly discussed. This method was developed specifically for mining operations with regional constraints and limited resources. Providing an in-field alternative to flame atomic absorption spectrophotometry and inductively coupled plasma optical emission spectroscopy, this entirely mobile XRF analysis method produces consistent and accurate results within minutes and at a fraction of the cost.

Jan 1, 2023

By C. G. Goncalves

The Gautrain rapid rail link project is currently Africa?s largest infrastructure project connecting South Africa?s major airport (OR Tambo), Johannesburg and Pretoria. Phase one is planned for completion in time for the 2010 FIFA Soccer World Cup and involves 80 km of track and 15 km of underground tunnels. The key shaft sinking blasting issues revolve around maximising advance and improving blasting cycles to meet the tight deadlines as well as environmental control which, in some cases takes place only 15m from the city infrastructure. To achieve success, DetNet South Africa supplied a range of electronic detonator systems to cater for the different blasting applications involved (tunnels, portals, shafts and viaduct foundations). One such product, QuickShot, was used for the first time in a major civil engineering project and has been used in most of the shaft sinking blasts to date. The QuickShot system combines pre-programmed electronic detonators with special on-bench components that enable the user to quickly and easily design the firing sequence solely by using the order of connections. This precludes the user from having to deal in absolute delay times. The connecting system enables benches to be hooked-up speedily by multiple users who have differing levels of experience. This paper provides details of how, after 33 months, the system has been embraced by the project by aiding in maximised advances, improved cycle times and meeting the required environmental constraints.

Jan 1, 2009

By M. I. Brittan

Discussion Dr R. E. Robinson (Fellow): The author must be congratulated on a very meticulous and self-contained piece of work. It is indeed a pleasure to read a paper that is so clearly and systematically laid out, and where the conclusions and the testwork conducted have been so clearly described. The paper is complete in itself, which makes it very difficult for someone who is not intimately involved in the whole Torco project to make any comments on its content. However, two points that, strictly speaking, fall outside the scope of the paper are of considerable interest. The first relates to the particle size of the material treated. In the paper, the testwork is confined to one standard particle size (minus 60 plus 100 mesh). The essential feature of the paper is to indicate that the rate-controlling reaction in the whole segregation process is the rate of reaction of the ore particles with the reducing agent and the hydrogen chloride. One wonders, therefore, to what extent this relatively slow rate of reaction is affected by the particle size of the ore itself. One imagines that the reaction must take place by contact of the hydrogen chloride with the surface of the mineral particles, and it is reasonable to suspect that the rate of diffusion of the copper ions to the surface is a relatively slow process and is thus the limiting factor in this particular rate of reaction. It is possible, for example, that the improvement obtained, when the ore is subjected to reducing conditions before the chlorination, is due to a breakdown in the crystal structure of the original particle. This breakdown is brought about by the reduction and by the consequent increase in surface area available for reaction with hydrogen chloride. Can the author indicate whether any work has been done along these lines, and whether it has been established that the reaction depends on the surface area available? The second point relates to the application of this kinetic study to the actual operation of a Torco reactor. It was once planned to feed the sodium chloride, together with the reducing agent, into the top of the segregation chamber. In the paper, the author mentions that it has now been established that the segregation chamber behaves, to all intents and purposes, as a fluidized bed, and that there is, therefore, a rapid evolution of gas in the lower regions of the chamber, which, it is imagined, displaces the gas phase rapidly. Since the reaction between sodium chloride, water vapour, and the aluminium silicates in the ore is extremely rapid, one wonders how much of the hydrogen chloride produced is removed from the reaction zone before it has had time to react with the copper minerals. The extremely low consumption of sodium chloride (which is a vital feature of the Torco process) must depend on an extremely rapid circulation of the hydrogen chloride gas to all the ore particles in the segregation chamber. One wonders, therefore, if a system for the introduction of the sodium chloride into the bottom regions of the chamber might not result in even greater efficiency in the utilization of sodium chloride. ProC D. D. Howat (Fellow): All of us who have been concerned with the study of chemical reactions at high temperatures are keenly interested in kinetics and are well aware that this is not an easy study experimentally. Dr. Brittan is to be congratulated on the development of neat experimental methods and for his full discussion of the results obtained. Although the segregation process for the extraction of copper from oxide and silicate ores has been known for almost fifty years, the fundamental chemical and physical changes involved have been little understood and the fundamental data are very scanty. The work now in progress at A.A.R.L., together with that sponsored by the Anglo American Corporation in other research institutions throughout the world, is bound to produce new fundamental data and a much more complete understanding of this rather fascinating process. It is already apparent that some of the old and well-worn chemical reactions that were postulated to occur, just cannot take place in the way which was formerly accepted. Dr Brittan's work, carefully conducted and thoroughly analyzed as it has been, still leaves us with one great outstanding problem. The thermodynamic data and the possible reactions set out in Table I (page 281) of his paper leave us asking, in complete despair, how can copper be converted into a volatile chloride in the presence of HCl, CO and carbon at temperatures about 800°C? The thermodynamics all combine to show that copper should be reduced to metal as the first step in the process. This brings us right up against the second problem. If copper were reduced to the metal how would HCI convert it to the volatile chloride? On top of these problems is the unknown reason for the very high speed of reaction between CO, HCI and the ground copper ore. Still further into the region of the unknown is the reaction by which gaseous hydrochloric acid is produced in the actual process. Perhaps Dr Brittan is feeling grateful that he doesn't have to try to explain this reaction-at this stage of the research programme at least. The results very clearly show that both CO and HCl gas are essential for rapid production of the volatile copper chloride. Dr Brittan states that 18 minutes were required to attain 83 per cent extraction with HCl gas alone and this was reduced to 4 minutes when CO was

Jan 2, 1970

By F. Botha

South Africa is amongst the 40 driest counties in the world, with extreme weather conditions and beset by both droughts and floods. Coupled with economic growth is an increased demand on water resources and, as with all other industrial developments, mining requires large volumes of water, which is likely to have an impact on the environment. Further to this, the mining industry also realizes that minerals are a non-renewable resource and the contribution to wealth creation from mineral extraction is not everlasting. It serves as an economic boost and careful planning is required to ensure that the legacy of mining is sustainable, and that some of the returns from mining provide continual economic and social prosperity.

Jan 1, 2012

By C. G. Verkerk

The paper discusses the transport and rheological characteristics of high concentration slurries or pastes for backfill purposes. The influence of pipe size, particle size distribution, additives, coarse material and mass concentration on these characteristics is addressed.

Jan 1, 1988

By P. E. L. Balestra, A. O. Filmer

The kinetics of the reactions involved in the non-oxidative dissolution of nickel concentrate in hydrochloric acid were studied by electrochemical and powder-leaching methods. It was found that the rate of non-oxidative dissolution increases with a cathodic shift in the mixed potential, which can be achieved by an increase in the nickel-to-sulphur stoichiometric ratio at the reaction surface. An unactivated concentrate with a sulphur content of 36 per cent exhibited a mixed potential of +O,3V (SCE) and could not be leached satisfactorily in 3 M hydrochloric acid at 60°c. When activated material (18 per cent sulphur) was leached, it had a mixed potential of -O,3V, and high iron and nickel extraction rates. Results reported by other workers on the non-oxidative dissolution of sulphides are explained in terms of the mixed potentials at which dissolution occurs.

Jan 1, 1981

By A. E. Landsberg, K. C. Corin, G. Stroebel, J. A. Miller, M. Becker, H. J. J. Gordon

Geometallurgy represents an integrated approach to mine planning and operation whereby the naturally occurring ore variability and its effects on all key downstream activities in the mine life cycle are considered. Process mineralogy is one of the key components of this integrated approach. This paper focuses on understanding some of the mineralogical variability across the Swartberg Cu-Pb-Zn sulfide ore in South Africa and its consequent effects on flotation performance. This process mineralogy project is motivated by the planned changeover and expansion of the Black Mountain Mines concentrator to process solely Swartberg ore compared to the run-of-mine blend currently being treated at the plant. Eight samples spanning the main lithological units of the ore body are described using quantitative mineral-textural data and bulk sulfide batch flotation performance to establish five process mineralogical or geometallurgical units comprising: quartz-pyroxmangite-magnetite, quartz-amphibolemagnetite, quartz-magnetite, garnet-magnetite-quartzite and mica-quartzite ores. Important mineralogical characteristics affecting Cu, Pb and Zn recovery, grade and selectivity specific to the different ore samples are discussed. Ultimately, the use of ore-specific process mineralogical and geometallurgical knowledge allows for better mine planning and plant optimisation. Keywords: Flotation, polymetallic base metal sulfide ore, process mineralogy, ore variability

Jan 1, 2020

By J. le Grange, M. Tullmin, A. Strauss, F. P. A. Robinson, C. A. O. Henning

An experimental feritic stainless steel with a chromium content of 40 per cent was welded by laser and electron beam (EB) welding processes. These techniques were found to be particularly suited to the welding of this alloy in that the impact toughness of the weld metal and heat-affected zone (HAZ) of the laser welds compared favourably with those of the parent aloy. When the EB process was used, the impact toughness of the weld metal was over 180 J/cm2. Grain growth in the HAZ was minimal for welding with these two processes. Corosion tests, conducted in a solution consisting of 20 per cent sulphuric acid and 100 p.p.m. of potassium thiocyanate, and In a highly corrosive industrial solution, indicated that the laser and EB welds were free of sensitization effects, thus confirming the metalographic results.

Jan 1, 1989

By R. Gebrekristos

It is commonly accepted that three types of aquifers exist in the Bushveld Complex: (a) alluvial aquifers in areas of river courses, (b) weathered bedrock aquifer formed by the in-situ weathering of the bedrocks, (c) fractured aquifers underlying the weathered aquifers controlled by the regional and local fracturing of the crystalline rocks. Hydrogeological studies conducted in the Critical Zone of the Bushveld Complex in the western limb show that the UG2 pyroxenite layer is of a particular interest and has a unique aquifer property. It yields much of the groundwater inflow into some mines and can be classified as the most important aquifer in the vicinity of the mining zone. The UG2 pyroxenite aquifer is restricted to the dipping UG2 pyroxenite unit. The unit weathers more intensely than the surrounding norites and anorthosites and is characterized by deeper weathering horizons (two to three times deeper than the surrounding rocks). For much of the UG2 mining area between depths of 35 ? 80 m, stoping of the UG2 takes place approximately 5 ? 7 m below the UG2 pyroxenite aquifer, and usually there is no groundwater inflow into the mine workings. However, unsealed deep exploration boreholes intersecting the UG2 pyroxenite and reaching underground mine workings, or mine roofbolts penetrating the weathered pyroxenite aquifer from underneath, can result in significant groundwater inflows into the underground workings. The reason as to why the UG2 pyroxenite weathers more than the norites and anorthosites has not been fully studied but is suspected to be due to the bedding planes of the unit and mineralogical composition of the particular pyroxenes forming the unit, which result in preferential physical and chemical weathering under atmospheric conditions. The weathered pyroxenes form sand-sized, rounded grains with improved effective porosity and permeability suitable for the storage and passage of groundwater. The orientation of the pyroxenite aquifer can easily be determined as it dips with the Bushveld layered strata. No-flow boundaries can be assumed on the hanging- and footwall of the pyroxenite aquifer and the flow rates can be estimated using 2-dimentional analytical equations. However, this must be confirmed with strong conceptual models since the existence of a fracture network connecting the pyroxenite aquifer with the overlying weathered and/or underling fractured aquifers can complicate the system, lowering the accuracy of analytical models and necessitating the utilization of numerical models.

Jan 1, 2012

By A. C. Lawrence

A new approach to the -study of human factors in stope productivity by A. C. LAWRENCE B. Econ., D. Com. (S.A.) (Member) The extent of the improvement in mean performance which could be achieved by reducing the variance between stoping gangs is examined, and it is shown that a worthwhile gain would result if variance were reduced by as little as 5 to 15 per cent. The problem of identifying human factors which contributed towards variance in gang performance was examined in one gold mine. A total of 342 'observations' on 49 stoping gangs were gathered, each observation consisting of a set of figures for 36 variables for one gang for one week. The variables included 'stope factors' such as face length, 'gang factors' such as the ethnic composition of the gang, and 'supervisory factors' such as the experience of the miner. These variables were related to 'tons trammed per week' as a measure of work performance. The findings showed that certain of the predictor variables accounted for 66 per cent of the variance in gang performance and about two thirds of this could be attributed to gang and supervisory factors, that is to the 'human factors'. The method suggests a basis for a new approach to the identification of human factors and is a promising step towards optimizing gang performance.

By Sönke Schmachtel

Several possible physico-chemical properties of composite electrodes for oxygen evolution are presented to describe experimental data for which a mathematical model had been developed. On this basis, local electrical and electrochemical properties of a composite electrode were investigated with conductive atomic force microscopy (CAFM) and scanning electrochemical microscopy (SECM). It could be shown by CAFM measurement that the boundary between matrix and catalyst particles seemed to have special advantageous electrical properties. The SECM measurements showed the presence of mass transport phenomena with increased surface concentrations, whilst the thickness of the Nernst diffusion layer was very small. An intermediate was detected and assigned to be hydrogen peroxide. From all species involved in the oxygen evolution reaction (H2O2, H+ and O2), it was concluded that local active spots exist on the electrode on which hydrogen peroxide reacts to oxygen and protons. A two?step two-material process was suggested to explain the whole oxygen evolution mechanism.

Jan 1, 2008

By D. Fourie

A brief history of channel sampling in South African gold mines is followed by a chronicle of different sampling events and sampling methods that used the traditional ?hammer and chisel? approach as well as diamond core extraction of the sample. The problems associated with each method of sample collection are documented and the use of a laser scanner to measure the exact volumes of sample material extracted from a correctly delimited sample site are considered. Areas where increment delimitation errors (IDEs), increment extraction errors (IEEs), increment weighting errors (IWEs), and increment preparation errors (IPEs) occur were investigated. A ?simulated chip sample model? is introduced and provides the basis for comparing the percentages of error introduced as a result of improper sampling. The heterogeneity experiment showed that reefs that are more homogenous tend have lower extraction errors than the more complex carbon-rich reefs, which may contribute to understanding the poor mine call factor on mines exploiting the latter types of reef. Keywords channel sampling, chip sampling, error, bias, modelling.

Jan 1, 2014

By J. H. Zietsman, W. J. Leipoldt

"To be able to responsibly develop a multiphysics model of the steel belt sintering (SBS) process used to sinter chromite fines, it is important to have a comprehensive understanding of the process. This understanding was gained through a site visit, observation of the process in operation, and interaction with the operators. Material characterization will also reveal much about the process that is not yet fully understood. A well-defined and representative mass and energy balance will also give valuable insight into the process. The plan for the multiphysics model aims to combine a computational fluid dynamics (CFD) model with a discrete element method (DEM) model.To obtain a more accurate mass and energy balance representation of the SBS process, it was decided to develop a dynamic distributed parameter model of the mass and energy balance. This model will be used to gain better understanding of the SBS process so that a more complicated multiphysics model can be developed later. The reason for this is because the SBS process is very dynamic, with a large temperature distribution throughout the length of the process. In its current state, the mass and energy balance model is capable of handling solid and gas material packages and exchanging heat between these packages where they are mixed, and is able to model the heating of the gas by burning CO gas. The next step in the development of the model will involve enabling it to handle evaporatoin of liquid water, burning of solid carbon in the pellets, reduction of iron oxide in the pellets with the CO gas formed from carbon combustion, and then oxidation of the reduced iron in the oxygen-rich cooling zones."

Jan 1, 2014

By M. Keevy, K. Hackney

Centrifugal slurry pump station and deposition sites are a common feature of many mines and mineral processing plants. Yanacocha Mine has completed the design of a pump station consisting of two trains of four pumps each. A number of trade-off studies was conducted to optimize the pump station design. The most significant of these was determining the drive types for the slurry pumps. The pump station duty can vary considerably due to the number of deposition points round the disposal site. The standard solution to this problem on a multi-stage pump train is to install one pump with a variable speed drive to control the pump station output by varying the speed of this pump and stopping and starting other stages. However, there are a number of negative impacts associated with this approach. These include head losses through pumps that are stationary or ?wind-milling?, different wear life on pumps that are running and pumps that are stationary, and slower response to the control system with the possibility of hunting. The use of variable speed drives on all the pumps was considered as an alternative to the standard solution. The factors considered in comparing these options were the control and operational differences, the pump efficiencies and absorbed power, the expected pump wear life, the impact on pump maintenance and the cost of the drive options. For this project the option of using all variable speed drives was selected. The paper presents the following aspects of the study: ?Description of the various options investigated. This includes a discussion on the required duty and the drive options. ?Technical comparison between the options. ?Description of the factors influencing pump performance and life.

Jan 1, 2007

By P. Saari

The Talvivaara deposits are located in Eastern Finland, within the Kainuu Schist Belt. These polymetallic sulphide deposits are of relatively low grade, but bioheapleaching enables economically profitable nickel extraction from the ore. Zinc, cobalt, and copper are also produced. Talvivaara?s production process begins with large-scale open-pit mining and four crushing stages, followed by stacking of the ore in bioleaching heaps. The ore is first leached for 13?14 months on the primary leach pad, after which the leached ore is reclaimed, conveyed, and re-stacked on the secondary heap pad. After secondary leaching, the barren ore will remain on the secondary heaps permanently. In the metals recovery process, the metals are precipitated from the pregnant leaching solution. Construction of the process was begun in spring of 2007 and first metal sulphides were produced at the plant in October 2008. The development of the bioheapleaching process was begun in a 17 000t on-site pilot heap operated during 2005?2008 and has continued in the industrial heap. At industrial scale, the development measures have focused on improving the permeability and aeration of the heap. Challenges with crushing and aerations systems at the beginning of industrial-scale leaching delayed the increase in metal recovery, but after the first two operational years the leaching results have improved significantly and the process is performing as targeted.

Jan 1, 2012