Search Documents

By E. L. McHugh, J. M. Girard

This paper discusses the results of two recent case studies in which high-tech prototype instruments were used. The first case study describes the results of a ground-based hyperspectral imaging tool used to map the geology of an open-pit mine highwall. The second case study outlines the use of interferometric synthetic aperture radar and how this type of radar can be used in a variety of geotechnical situations. These case studies are part of an on-going research project at the National Institute for Occupational Safety and Health’s (NIOSH) Spokane Research Laboratory. The project objective is to implement engineering controls and design methods in order to reduce the number of injuries and fatalities associated with slope failures at mining operations. Project personnel are hopeful that these new developments in technology will lead to better geotechnical monitoring and design in slope stability and other important areas of rock mechanics.

By Lloyd Williams

1. The investigation shows that the Coal Creek has been the most productive, bed in Campbell County and contains the largest recoverable reserves of coal. The Pewee, Red Ash, and Jullico have been relatively productive beds and contain appreciable recoverable reserves of coal. The Blue Gem also has been productive in the past, but available information indicates that most of the remaining coal is Less than 28 inches thick. The Big Mary has relatively large reserves over 28 inches thick, but the coal is high in ash and sulfur. Thick partings in the Windrock bed have discouraged mining in that bed. The Poplar Creek and Rex beds generally are below drainage, and large areas have been excluded from the reserve estimate, Reserves in the Walnut Mountain bed will be difficult to mine due to the irregu¬lar thickness and lack of continuity of the bed. Estimated coal reserves are- small in the remaining five beds. 2. Known measured and indicated reserves of coal, based on a minimum bed thickness of 14 inches and on 1,800 short tons per acre-Foot of coal in place, are estimated to be 398 million tons as of January 1, 1953, o? this total, 267 million tons is in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics are too meager to make an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, these should be added to the total estimated reserves.

Jan 1, 1956

By H. B. Hill

The Salt Flat field, formerly called the Toe -Bruner field, is located northeast of the town of Luling in Caldwell County, Tex. This field, which is a fault structure, approximately parallels and is about 5 miles east of the Old Luling field. The proved area is approximately 1,280 acres, on which 332 producing wells (September, 1930) have been drilled. The majority of the wells are producing from the Edwards limestone at an average total depth of 2,700 feet. A few wells are producing from the Austin chalk or from other formations above the Edwards limestone. The Wilcox formation is exposed, and the fault trace in places is scarcely evident. The strike of the structure is approximately 111. 20 to 45° E. The displacement of the fault is probably 200 to 500 feet. The discovery well was completed in the Austin chalk by the Lutex Oil Co. during April, 1928. In October, 1928, the Sun Oil Co. completed the discovery well in the Edwards pay. This well was an important discovery, as it indicated the potential oil possibilities of the Edwards limestone in echelon fault structures. The discovery led to the development of the third fault field in the Edwards limestone and opened up a large area for future prospecting. The total oil production for the Salt Flat field to and including September, 1930, was 19,833,215 barrels. The most reliable figures available of water production were compiled for a number of leases and wells in the south half of the field. These data show that the water percentage for the average well in this part of the field increased steadily from 30 per cent for January, 1929, to 81 per cent for December, 1929. The estimated daily water production of the entire field for December, 1929, was about 82,000 barrels as compared with a daily oil production of 29,725 barrels; or approximately 2.7 barrels of water were produced with each barrel of oil 14 months after the discovery well was completed in the Edwards pay. Estimates of water production in the (Old) Luling field, which is near the Salt Flat field, place the daily water production at about 150,000 barrels (July, 1929) as compared with a daily oil production of 11,000 barrels. These figures indicate that in the Luling field approximately 14 barrels of water must be lifted for each barrel of oil produced. The Luling field was discovered in August, 1922, and a peak annual production of 10,210,000 barrels was reached during 1924. The production during 1928 was 5,057,000 barrels of oil from an average of 567 producing wells for the year. Although water appeared early in the life of the Luling field, the oil production has been well sustained. Another feature of outstanding interest is the comparatively few producing wells that have been abandoned on account of water during the soven years of operation of this field. Comparison of data between the Luling and Salt Flat fields is of importance because of the nearness of the two fields. The Luling field is a narrow strip or "shoestring" approximately 8 miles long, with a maximum width of 3,400 feet. Production is obtained in the Edwards limestone at an average depth of 2,200 feet on the upthrow side of a fault. Similar conditions of accumulation are found in the Salt Flat field at greater depth to Salt Flat field as outlined (April, 1930) is about 7 miles long? with a maximum width of 2,000 feet. At the time the field work was begun (July, 1929) in the Salt Flat field, drilling operations had been almost completed in the south half of the field, while the north half was still under development. Cross sections and a structure contour map interpret the subsurface conditions in the south half of the field, where the water conditions first became serious.

Jan 1, 1931

By Bill Linville

During calendar year 1972, the Bureau of Mines was engaged in some 20 major areas of research for the development of new and improved efficient methods of conservation and utilization for petroleum and natural gas, oil shale, and coal. Made up of numerous projects described in this report, the program was carried out through research performed at research centers and laboratories in the field supervised and supported by administrative personnel of this Bureau of the Department of the Interior. Based un this research, 186 technical reports were published by the Bureau or others, and numerous other reports were prepared for Federal agencies, State agencies, and organizations engaged in cooperative research programs with the Bureau.

Jan 1, 1973

By Anthony M. Opyrchal

This Bureau of Mines study assesses the economic significance of the Florida phosphate industry to selected counties in Florida, the State of Florida, and the Nation: it also includes a brief survey of the industry's international impact. Based on forecasts of Florida phosphate production in 1981, and using constant 1977 dollars. estimates are given for 1981 for regional and national output the value of this output, income, and employment created by the phosphate industry in Florida, Federal, Stale, and county tax revenues generated by the State's phosphate industry are also estimated for 1981. The concentrated impact of the phosphate industry on certain areas of Florida and on the State?s regional industries is examined using economic base analysis complimented by an industrial complex approach. The industry's impact at the Stare and national levels is examined through input- output analysis. In addition, an attempt to forecast for 1990 the effects of constraints on phosphate rock mining as a result of economic conditions and other factors is included as an appendix to the report. Also discussed is the phosphate industry's importance to the U.S. balance of trade: U.S. agricultural production. Including forward linkages; the U.S. sulfur industry; and the phosphate industry's importance to the production of fluorine and uranium by- products from fertilizer manufacturing.

Jan 1, 1981

By Kung-Lee Wang

This report describes the linkage of all mining sectors with all other manufacturing, services, and final demand sectors of the U.S. economy. Besides being a basic data source, it provides a framework for aggregate economic impact analysis with respect to the mining industries. The framework is an open-static input-output model specifying 48 mining industries as classified in the Standard Industrial Classification Manual for all mining activities and 76 nonmining industries which collectively exhaust, all economic activities. The 124-sector model used in this report is an expansion of the preliminary 82-industry aggregation estimates made by the Department of Commerce. In the expanded model, 48 ruining industries are substituted for the original 6. The methodology used to ascertain the industry-by-industry procurement cost estimates and product ion flows necessary to the construction and expansion of the basic 82-sector model included personal interviews, case studies of specific mining activity analysis, and published and unpublished data from the Bureau of Mines and the Census of Mineral Industries, The end products of this study are two tables arranged to show the direct purchases necessary for each industry to support the level of economic activity and the total purchases generated in each industry throughout the economy by each $1 of aggregate economic demand in 1958. The tables may he used for economic impact studies and market analysis by firms engaged in or closely associated with the mining industries. Some illustrations of their usages are presented.

Jan 1, 1967

The U.S. Bureau of Mines Information and Analysis Directorate collects worldwide data on virtually every commercially important nonfuel mineral commodity. These data form the base for tracking and assessing the health of the minerals sector of the U.S. economy. The Bureau's data collection activity was instituted by the 47th Congress in an appropriations act of August 7, 1882 (22 Stat. 329), which placed the collection of mineral statistics on an annual basis. The most recent authority for the U.S. Bureau of Mines survey activity is the National Materials and Minerals Policy, Research and Development Act of 1980 (Public Law 96-479, 96th Congress). This act strengthens protection for proprietary data provided to the U.S. Department of the Interior by persons or firms engaged in any phase of mineral or mineral-material production or consumption.

Jan 1, 1993

By C. W. Davis

During the fiscal year 1935-36, the Ore-Testing Section has been active in carrying out a program designed to attain the objectives that have been set up for it. For the purpose of standardizing important testing methods, an attempt has been made to develop a rationalized scheme for ore testing, starting with preliminary investigations to determine the physical and chemical properties of the ore, following this with a logical selection and trial of processing tests to find out how the ore may be most effectively treated, and concluding with a discussion of what interpretation may be placed on the results in terms of plant design and operation. A selection of procedures that appear well-suited to the ore-dressing problems under investigation is included in the following paper of this report so that other experimenters may be enabled to verify our findings and to offer criticisms and suggestions for improving our practice. A tentative scheme for the evaluation of flotation reagents is being investigated, and some progress has been made in a study to determine the significance of small-scale testing. These projects have required 899 analyses. Papers on these and others on ore testing, such as testing for amalgamation and for cyanidation, will be included in future annual reports.

Jan 1, 1937

By C. W. Davis

During the fiscal year 1935-36, the Ore-Testing Section has been active in carrying out a program designed to attain the objectives that have been set up for it. For the Purpose of standardizing important testing methods, an attempt has been made to develop a rationalized scheme for ore testing, starting with preliminary investigations to determine the physical and chemical properties of the ore, following this with a logical selection and trial of processing tests to find out how the ore may be most effectively treated, and concluding with a discussion of what interpretation may be placed on the results in terms of plant design and operation. A selection of Procedures that appear well-suited to the ore-dressing problems under investigation is included in the following paper of this report so that other experimenters may be enabled to verify our findings and to offer criticisms and suggestions for improving our practice. A tentative scheme for the evaluation of flotation reagents is being investigated, and some progress has been made in a study to determine the significance of small-scale testing. These projects have required 899 analyses. Papers on these and others on ore testing, such as testing for amalgamation and for cyanidation, will be included in future annual reports.

Jan 1, 1937

By W. L. Dare

This information circular is one of a series the Bureau of Mines plans to publish describing the methods and costs of mining uranium on the Colorado Plateau. The Big Buck mine is one of the larger underground uranium-vanadium ore mines on the plateau. The mine is about 39 miles southeast of Moab in the Big Indian mining district, San Juan County, Utah. The Big Buck claims were located late in 1947, when uranium mineralization was discovered in the Cutler formation at its outcrop along the escarpment that forms the west side of Big Indian Wash. Charles A. Steen made the first major discovery of uranium ore in the Chinle formation in the Big Indian mining district on July 6, 1952, when 14 feet of high-grade uranium ore was encountered in a diamond-drill hole drilled on his Mi Vida claim. The Big Buck ore body now being mined by Standard Uranium Corp. is a southeast extension of Steen's original discovery.

Jan 1, 1956

By A. L. Podia

The purpose of this research was to develop a system capable of detecting changes in the structure of rocks, leading to failure of mine roofs, and/or excavations. A prototype system was developed, field tested and delivered to the United States Bureau of Mines for further evaluation and research. This system is based on the analysis of acoustic signals generated on the surface of the roof by an impact device and which are reflected or backscattered by flaws and discontinuities in the rock. The specially designed impact source is capable of generating high frequency acoustic signals with excellent repeatability. The system can also be used in conjunction with conventional acoustic pulse transducers. The received signal is digitized and the data transferred to a minicomputer for processing and display. This capability allows the immediate determination of wave velocity and/or distance to a reflecting interface. Various data processing techniques such as averaging, differentiating, and comparing of different signals can be selected by entering the appropriate commands on the keyboard. Being a programmable system it is possible to implement more advanced signal processing techniques. All results as well as the signal are displayed on a CRT. Furthermore, a permanent record of the data can be generated on paper tape, which can be reentered and processed at a later date. A communications interface allows transmission of the sampled signal to a large scale re-mote computer. The system was tested extensively in the laboratory, and field tested at the York Canyon Coal Mine. These tests proved the feasibility of operation in the mining environment. Results indicate that further investigation and development will have to be undertaken to fully develop the potential of this system in satisfying the goals of this research.

Jan 1, 1973

By W. J. Kroll

This investigation was undertaken with the idea of studying a number of unconventional methods for making chromium to determine whether production cost could be lowered and to discuss some of the more recently described processes. These comprise carbon reduction of the oxide in vacuum, nitride dissociation, fusion electrolysis of the chloride, amalgam method, iodide dissociation, calcium reduction of the oxide, hydrogen reduction of the chloride, and reduction of this compound with zinc and with magnesium. Preference is given this latter method, which is shown in a flow sheet. Special attention is given purification of the chloride and separation of the vacuum at about 900° C. A reduction method for the elimination of traces of oxide contained in pure chromium by pure hydrogen obtained from the dissociation of zirconium hydride is described. The various methods are compared in a table in the appendix. Aluminothermic and silicothermic methods for the reduction of chromium oxide and the aqueous electrolysis have been disregarded in this investigation.

Jan 1, 1950

By James C. Barker

The analytical variability encountered when sampling for platinum-group metals (PGM) was statistically evaluated during a 1983 study by the Bureau of Mines and the University of Alaska. Sampling procedures were designed to systematically incorporate commonly used reconnaissance exploration techniques under actual field conditions. Analytical variability was evaluated at each procedural step. Analytical data from each sample from a single deposit grouped relatively well around the calculated mean for that deposit. Standard deviations did not exceed 43 pct of the mean for any of the deposits; more commonly, the deviation was about 25 pct. Statistical treatment of the data by analysis of variance indicated the most important source of error is selection of the sample site. Two or more replicate samples appear necessary to adequately quantify the PGM content. Secondly, significant variation occurs during preparation of a pulverized split for fire assay. The optimum sample size was in the 11-lb range; larger samples did not appreciably reduce variability. Smaller samples generally indicated a higher degree of variability. Evaluation of the sample method suggested the common grab sample, if carefully taken, is a useful indicator of the general range of PGM concentration but potentially includes a considerable margin of error.

Jan 1, 1985

By A. Stawsky

Effective use of diesel vehicles in underground mining requires attention to improved control of diesel exhaust pollutants such as particulate (soot), oxides of nitrogen and sulfur and carbon monoxide. An experimental survey Is made of diesel emission aftertreatment control techniques including water scrubbers, catalytic converters, exhaust gas recirculation (EGR) and soot filters. Use of two or more techniques in combinations are tested for optimum control of all exhaust pollutants. Dynamometer data is developed for steady state and computer controlled simulated mines duty cycles operation of Deutz F6L-714 and F8L-413 engines. Exhaust Quality indices (EQIs) are calculated from dynamometer data for comparisons among the control combinations examined. The Corning diesel particulate filter (DPF) is shown to be the most promising and practical device. The Corning DPF in combination with EGR provided the best (lowest) EQI from the test data. Use of the DPF requires additional regeneration mechanisms such as a catalytic filter coating or fuel additives. A metal mine field test is made of DPFs on an operational scoop tram to test practical applicability. Further development is proposed for application to various mine conditions and for improvement of DPF regeneration techniques including coating with newly available catalysts.

Jan 1, 1987

I. Domestic Production and Use: In 1981, 13 companies operated 32 primary aluminum reduction plants, with 3 firms accounting for 58% of production, Washington, Oregon, and Montana accounted for 32% of the total production; Texas, Louisiana, and Arkansas 16%; Tennessee, Alabama, South Carolina, and North Carolina 17%; other central and eastern States 35%. Based on published producer prices output of primary metal in 1981 was valued at over $7.5 billion. Aluminum consumption by 25,300 firms was centered in the East Central United States. Packaging accounted for an estimated 30% of domestic consumption in 1981, building 21%, transportation 18%, electrical la%, consumer durables 8%, and other uses 13%

Jan 1, 1982

By Herbert H. Einstein

This report contains the documentation for 11 computer programs representing the entire computer documentation for the eight-volume report entitled "Risk Analysis for Rock Slopes in Open Pit Mines." A detailed summary of the programs is included.

Jan 1, 1979

By F. F. Netzeband

This report relates to the sulfur industry of seven States--Arkansas, Kansas, Louisiana, Mississippi, Missouri, Oklahoma, and Texas--and is part of a national study of the sulfur industry by the Bureau of Mines. Markets as used 1n this report are divided into two components for individual analysis--(1) supplier markets which include regional Frasch and byproduct sulfur producers and (2) consumer markets which include processors and manufacturers requiring sulfur in their operations. The term sulfur as used in this report includes brimstone, native sulfur, elemental sulfur, or sulfur equivalents.

Jan 1, 1964

By Robert G. Bottge

The Bureau of Mines investigated the availability of the land in south-central Alaska for exploration and mineral development of locatable minerals under State or Federal laws. The land ownership for an area of nearly 72.5 million acres in south-central Alaska was divided into 3 availability categories and 15 subcategories. In July 1985, 31.0 million acres of the study area were available for mineral exploration and development, 6.2 million acres were available with restrictions, and 35.3 million acres were unavailable. About 23.6 million acres in the study area are underlain by mineral terranes. About 9.9 million of the 23.6 million acres are available for mineral entry, 2.4 million acres are available with restrictions, and 11.3 million acres are unavailable. While much of the land currently classified as unavailable will be reclassified once it is conveyed to the State or to Native corporations, about 22% of the unavailable lands underlain by mineral terranes are now Federal parks, preserves, wildlife refuges, wild and scenic rivers, and military lands, all of which are considered permanently unavailable for mineral exploration and development.

Jan 1, 1986

Mine waste and mine reclamation are topics of major interest to the mining industry, the government and the general public. This publication and its companion volume are the proceedings of a conference held in Pittsburgh, April 19-21, 1988. There were nine sessions (50 papers) that dealt with the geochemistry, hydrology and problems of mine waste and mine water, especially acid mine drainage. These comprise Volume 1. The nine sessions (43 papers) that dealt with reclamation and restoration of disturbed lands, as well as related policy issues, are included in volume 2. Volume 2 also contains the ten papers that pertained to control of subsidence and mine fires at abandoned mines. Poster session presentations are, in general, represented by abstracts; these have been placed in the back of both volumes.

Jan 1, 1988

By Harold J. Bennett

This study was performed by the Bureau of Mines to evaluate the potential supply of primary copper from domestic resources. A tonnage-price relationship was developed indicating the quantity of copper that could be produced economically from known deposits at various copper prices and at various rates of return on the required capital investment. Costs of production are based on estimated capital and operating costs for mining, concentrating, smelting, and refining the copper. Total known recoverable copper resources are 189 million short tons of which 83 million tons could be economically recovered assuming a price of $0.50 per pound of copper, credit for the recovery of byproducts, and a 12-percent rate of return on capital investment. The quantities of recoverable byproducts associated with the 83 million tons of recoverable copper are molybdenum, 1.8 million tons, gold, 43 million troy ounces, and silver, 740 million troy ounces.

Jan 1, 1973