Search Documents

By D. K. Denton, J. M. Girard, D. F. Scott, T. J. Williams

Personnel from the Spokane Research Laboratory, National Institute for Occupational Safety and Health, examined an underground pillar at the Homestake Mine, Lead, SD. Investigations involved strain relief and seismic tomography studies in the mine, and ultrasonic velocity measurements on pillar core in the laboratory. Measured octahedral normal stress was 37 MPa (5,366 psi); seismic P-wave velocities averaged 5.2 km/s (17,060 ft/s); and ultrasonic velocities at a pressure of 39.6 MPa (5,750 psi) averaged 6.3 km/s (20,669 ft/s). The difference between in-mine and laboratory velocities is attributed to the attenuation of seismic energy by mine fractures larger and more numerous than those in the samples of core measured in the laboratory. Using these results, researchers hypothesize that pillar rocks have the ability to withstand stress an order of magnitude greater than they currently sustain.

Geophysical Abstracts 1 - 86 were issued in mimeographed form by the Bureau of Mines; Abstracts 87 - 111 were published in bulletins of the Geological Survey; Abstracts 112 - 116 were issued in mimeographed form by the Bureau of Mines as Information Circulars 7256, 7257, 7267, 7273 and 7285. 1. GRAVITATIONAL METHODS 7380. Dryden, H. L. A reexamination of the Potsdam Absolute Determination of Gravity. Jour. Research Nat. Bureau of Standards, vol. 29, No. 5, 1942, pp. 303-314.

Jan 1, 1944

By Matthew N. Rubin

This report summarizes the work performed under USBM Contract No. H0155155. The purpose of this work was to obtain operational data on retrofit noise control treatments suitable for use in coal preparation plants. This data was obtained by evaluating the performance of four categories of noise control treatments which were installed in a commercial coal preparation plant. The four categories of treatments were resilient screen decks, resilient impact pads, chute liners, and curtains. The selection, installation and initial evaluation of the treatments was documented in the Volume I report issued in 1977. This Volume II report summarizes the results of the long-term evaluation of the original treatments, as well as some additional tests which were conducted on elastomer-clad (resilient) screen decks. This project demonstrated the feasibility of a number of retrofit noise control treatments, some of which also proved to be quite durable over the long term.

Jan 1, 1982

By Dennis R. Dolinar, Gabriel S. Esterhuizen

In this National Institute for Occupational Safety and Health (NIOSH) investigation, numerical modeling is used to evaluate the degree the pillar strength is increased with a rectangular pillar over a square pillar. Three-dimensional models are developed with pillar sizes and geometries typical of underground limestone mines in the United States. Physical properties for the models are based on geotechnical surveys of nearly 30 underground limestone mines. To examine the effects of pillar length on pillar strength with the modeling, a parametric study was conducted where the pillar width was held constant while the length and height were varied resulting in width-to-height ratios ranging from 0.5 to 1.5 and width to length ratios ranging from 1 to 6. There are two aspects to pillar strength and failure. At relatively low stresses, pillars can fail as a result of geologic structure. At greater depths and sufficient extraction ratios, the pillars can also fail as a result of the vertical stresses exceeding the pillar strength. The effects of increasing pillar length regarding both strength aspects are presented in this study. Equations were developed for the increase in pillar strength with both height and length based on the model results. The results from these equations were compared to those from previously developed empirical equations for rectangular pillars. For the more slender limestone pillars with a width-to-height ratio below one, there is little increase in pillar strength for length-to-width ratios above 2 and almost no increase with length for a width-to-height ratio of 0.5. Only with the more squat pillars is there a significant improvement in strength with length. The gain in pillar strength with length for the pillars is explained by the change in the ratio of the area of the pillar affected by the ends to the area of the pillar. For the squattest pillar, the change in strength is also affected by an increase in pillar confinement along the central length of the pillar as the pillar transitions from a square to a long rectangular pillar. With geologic structure, added pillar length can significantly improve the pillar strength, depending on the strike of that structure with respect to the long pillar axis.

By Philip W. Holland

This Bureau of Mines report discusses the results of three independent reconnaissance geochemical surveys conducted in the vicinity of the Bush Dome reservoir in the Bureau-owned Cliffside field near Amarillo, Tex. The surveys consisted of (1) determining the helium content of area ground waters, (2) determining the helium content of area soil gases and ground waters, and (3) determining the helium content of soil gases collected on a grid sampling pat- tern in the Cliffside field area. The native natural gas in the Cliffside field contains about 1.8 percent helium. To date, approximately 54 billion cubic feet of gas containing approximately 39 billion cubic feet of helium has been injected into the center of the Bush Dome structure. The research work, which was completed under contracts, was done to determine if helium concentration levels in ground water and soil gas could he used as an indication of the presence of helium in a subsurface natural gas accumulation. Results of the surveys were positive in that helium-in-water and helium-in- soil-gas anomalies were detected in portions of the Cliffside field area. All helium analyses were performed by mass spectrometric techniques.

Jan 1, 1979

The objective of this study was two-fold: 1. To perform a world literature search pertinent to the analysis, selection and design of hoisting systems and their components and to codify the search into a literature compendium. The search resulted in a technical data file of over 1500 hard copy items. The compendium index was also suitable for establishing a comprehensive computer-loaded data base on the subject. 2. To develop a comprehensive system of guidelines to cover salient aspects of analysis, selection and design of electrical, mechanical and structural components of a hoisting system with a view to establish parameters for maximum safety and efficiency of operation, installation and revision of the system. 3. Considerations in the mine shaft layout, design, sinking, outfitting, testing and commissioning are set forth against the background of requirements of applicable parts of Code of Federal Regulations, Title 30.

Jan 1, 1988

By R. D. Joseph

This report deals exclusively with roof-fall accidents that occurred during 1955 and 1956 in both anthracite and bituminous-coal mines throughout the United States. The report stems from a cooperative study conducted by the Bureau of Mines and the Roof-Control Committee of the Coal-Mining Section, National Safety Council. The study includes an analysis of individual accident reports, sets forth the measurable factors, and compares such factors with a representative sample of average data from 39 anthracite mines and 117 bituminous mines (appendixes A and B). Particular emphasis is placed on fatal roof-fall accidents with respect to their causes, locations, and the methods of support used at the point of occurrence. INTRODUCTION The purpose of the report is to classify all measurable details of the occurrences of roof-fall fatalities so that the material presented will assist those promoting safety and will serve as a manual for those whose principal duty is inspection of mines.

Jan 1, 1958

By K. J. Liles

This Bureau of Mines paper describes the composition and properties of drilling fluids for use in high-temperature geothermal wells, and summarizes the problems encountered with fluid use at the known major geothermal sites throughout the world. These include the western continental United States, Hawaii, Italy, Iceland, Japan, New Zealand, and Turkey. Water-base drilling fluids of 9- to 10-lb/gal weights are relied on primarily for geothermal well use, although air drilling is sometimes used. Bentonite-lignite-water systems have been used most often, and additives such as polyacrylates, lignosulfonates, and chromates are employed to improve the properties of the basic system.

Jan 1, 1976

By Fred N. Kissell

In This Chapter [Ventilation and methane sampling guidelines for conventional shafts Dealing with restricted spaces where methane can accumulate Ventilation and methane sampling at raise bore drills and Filling shafts at closed coal mines] It is not unusual to encounter methane gas during shaft excavation or shaft-filling operations. Shafts into coalbeds usually produce the most methane, so the information in this chapter applies primarily to shafts at coal mines. Nevertheless, much of the information is relevant for noncoal mines that have methane in the mine or in the overlying strata. METHANE IN SHAFTS EXCAVATED BY CONVENTIONAL MEANS (DRILL, BLAST, MUCK) [ ] Ventilation. Shafts excavated by conventional means are ventilated with a fan on the surface connected to ductwork that extends down into the shaft (Figure 9–1). Shafts into coalbeds should have ventilation systems designed to handle the higher gas flows to be expected as the shaft excavation passes through any over-lying gas-containing strata and nears the coal-bed to be mined. Following are some simple ventilation guidelines for the minimum amount of air required and the selection of the ventilation duct: • Provide enough air to meet the mini-mum OSHA tunnel requirement of 30 ft/min air velocity in the open shaft, as specified in 29 CFR2 1926.800(k)(3). For example, a 20-ft-diam shaft having

Jan 6, 2006

Horizontal holes are drilled underground into coalbeds to control methane flow from ribs and active face areas and to make gas pressure measurements in coalbeds. Gas pressure measurements are made by drilling the same hole incrementally. After each increment, the hole is filled with some type of packers and allowed to reach equilibrium before a gas pressure reading is taken. As the length of hole increases, more packers are required to effect a seal and obtain a reliable pressure measurement. Problems have been encountered in obtaining satisfactory packer seals due to the friable nature of the coalbed. New methods of packing the holes must be used. Therefore, this project was established to evaluate materials and develop a new technique in which a semiliquid and/ or rigid type grout could be placed in the hole to provide satisfactory sealing.

Jan 1, 1972

By C. Hellar

A new dual-boom remotely controlled roof bolter was designed, fabricated, and then tested in an underground coal mine. Remote-control functions allowed complete bolting cycles to be performed on two booms with both operators located within protective cabs. Capabilities included 3-to 6-foot-long bolts in 5-to 8-foot seams, limited to bolts 20 inches shorter than seam height. Machine was in compliance with all regulations including dust collection, machine lighting, and permissibility.

Jan 1, 1979

The works recorded in this Test Report have been performed by Rade Roncar - Electrotechnical Institute of Zagreb, SFR Yugoslavia in collaboration with Bureau of Mines. The main objective of these investigations was to investigate the possibility of fabrication of thin-walled square enclosures of satisfactory safety factor in accordance with requirements of effective technical regulations. The results and the investigations can be divided in three main fields: - investigations of thin-walled enclosures with the view of determination of pressures causing technological deformations before performing tests in accordance with effective applicable regulations, - finding the safety factor by means of tests of metal-foam pressure vents, - comparison of enclosures with and without pretreatment by technological deformation.

Jan 1, 1987

The first metal-mine accident-prevention course was prepared and published in 1942-45 as a series of seven miners' circulars (Nos. 51-57). The scope of the course has been broadened, revised, and brought up to date, and it is being published as a similar series of seven miners' circulars (Nos. 51-57, revised) on accident prevention in metal and nonmetallic mines. These circulars are: Accident Statistics (Miners' Circular 51), dealing with general statistics on accidents and injuries at metal and nonmetallic mines, including causes, costs, and the uses of investigations and reports of all accidents.

Jan 1, 1955

By William J. Karwoski

To improve rock-burst control in deep vein mining, a field demonstration has been carried out by the Bureau of Mines to test a new rock-burst control concept--rock preconditioning in advance of mining. The procedure is to fracture the major rock-burst-prone zone during the development of each level before production mining. This allows initial mining to begin in a preconditioned zone and later mining from the level below to end in a prefractured or preconditioned pillar zone that is relatively burst-free. This full-scale field demonstration was carried out On the 7700 level of the Hecla Mining Co.'s Star-Morning mine. An expected burst-prone zone along the main vein between 7 and 10 crosscuts, some 250 feet long by 40 feet above and below the level, was preconditioned by blasting a fanlike ring of drilled holes from each crosscut. The drill holes, up to 100 feet long and 4 inches in diameter, were loaded with high explosives and shot. About 4,550 feet of drilling and 9,000 pounds of explosives were involved in the effort. Comparison of preshot and postshot data from monitoring instrumentation indicated that the blasting did fracture the rock in the planned zone and did result in an immediate stress decrease and softening of rock. The field data compared favorably with predicted results from a finite-element computer model simulation of the destressing. Based on observations made during mining and on the data from the Hecla rock-burst monitoring system, there is no doubt that this preconditioning in advance of mining demonstration resulted in much-improved rock-burst control during first-floor mining. It was also concluded that preconditioning the vein was more effective than preconditioning the wall rock.

Jan 1, 1979

By Frederick C. Tompkins

A complete service system was established for the monitoring of personnel exposure to N02 based upon the use of passive dosimetry. This system is structured such that minimum effort is required of the user: manufacturing, analysis, reporting, and record keeping functions are provided by the service organization. A field evaluation program was carried out in a dieselized mine to assess the performance of two passive dosimeters, the Walden GASBADGE TM dosimeter, and a tubular dosimeter developed at New York University. Side-by-side comparisons were carried out to evaluate dosimeter suitability for monitoring in the field, and to assess relative accuracy characteristics.

Jan 1, 1976

By James J. Scott

Eleven workshops were held in various locations throughout the country in an attempt to reach the many diverse groups working in various mineral commodity areas and special ties. These meetings were held between March 1, 1974 and June 25, 1975. They were held under the auspices of the Bureau of Mines Contract to the University of Missouri-Rolla which was designed to help define Bureau research and development priorities. At each workshop a summary of current Bureau research and development was presented and the attendees were asked to present their ideas on what Research and Development programs should be undertaken to meet their needs locally. Participants included representatives of federal and state agencies, educational institutions, mining companies, equipment companies and other interested parties. The workshops covered under this report include lead mining in Missouri, limestone mining, coal mining both surface and underground in the midwest and in the Rocky Mountain area, iron mining in Minnesota, two top management meetings on institutional problems and, finally, a special two-day meeting on roof control.

Jan 1, 1977

By Liming Yuan

A study of the ignition of non-fire-resistant hydraulic fluid sprays was conducted by the National Institute for Occupational Safety and Health. Both an open flame and a hot steel surface were used as the external heat sources. With the open flame as the heat source, the minimum oil temperature and minimum spray nozzle pressure that resulted in an ignition were measured. The effects of the distance between the open flame and the nozzle and the nozzle orifice diameter on the ignitability of the hydraulic fluid sprays were examined. With the hot surface as the heat source, the minimum surface ignition temperature was determined. The degree of oil atomization and the relative direction of oil injection with respect to the hot surface are discussed. The ignition of oil sprays from the impingement of oil jets onto a vertical surface was also investigated. Finally, the results are compared with those obtained for fire-resistant hydraulic fluids. Keywords: Ignition; hot surface; open flame; hydraulic fluid

Jan 1, 2006

By G. St. J. Perrott, N. A. Tolch

"The measured strength of an explosive depends to a certain extent on which it is determined. An earlier investigation showed the relative propulsive strength of dynamites as determined in one type of apparatus, ballistic pendulum.4 The aim of this paper is to precept strength data on these same dynamites determined in another type of apparatus, the Trauzl lead block, and to compare the results with those of the ballistic pendulum. Trauzl lead block have been in use many years for the determination of thy strength of explosives, under moderate confinement.5 The common practice is to shoot 10 grams of explosive, in tinfoil wrapper,- and then to measure the volume of the cavity produced by the shot. The volume of the original borehole is deducted from the gross expansion and sometimes a correction is made for the expansion produced by the detonator. Dry sand is used for stemming the charge.It has been found that the expansion in Trauzl blocks is not strictly proportional to the charge. Naoum5 believed that for scientific accuracy the charge should undoubtedly be regulated to give the same average expansion for each sample tested, but for expansions of 200 to 400 cubic, centimeters the deviation from proportionality is not sufficient to give results appreciably in error.Neubner7 found that the proportionality curve is tangent to the charge-expansion curve at about 300 cubic centimeters expansion, provided that no deductions are made for the volume of the original borehole or the effect of the detonator; the total or gross expansion is proportional to the charge between expansions of 250 to 350 cubic centimeters without serious error."

Oct 1, 1930

By Frank B. Fulkerson

Of the about 60 million pounds of aluminum used in the Pacific Northwest in 1960, 40 million pounds or two-thirds was used by 10 companies. One of these companies made airplanes and missiles; one manufactured roofing, siding, and tubing; three produced truck tractors, truck bodies, or truck trailers; two made architectural metal products; one made irrigation and industrial products; one was a general foundry; and one was a shipyard. These companies contributed to regional growth by developing markets outside the area; some have worldwide sales. Aluminum consumption increased at an average rate of 7 percent annually from 1954 to 1960. Airplane manufacture, formerly preeminent in aluminum use, no longer was in first place in 1960. By industrial group, the leading users were manufacturers of building products, 30 percent; airplanes and missiles, 22 percent; truck tractors, truck bodies, and truck trailers; 17 percent; general foundries, 5 percent; ships and boats, 4 percent; mobile homes, 4 percent; other transportation equipment, 3 percent; and irrigation equipment and all other products, 15 percent.

Jan 1, 1962

By D. H. Yardley

A major purpose of this contract was to evaluate a variety of dust suppressants to determine their effectiveness in mitigating dust from taconite tailings. During the course of the investigation tailings from pilot-plant tests of Minnesota copper-nickel ores became available and chemical binders were also tested for dust mitigation effectiveness on this mineralogically different material. Field-test plots were established on taconite tailings and wind tunnel laboratory tests conducted. The laboratory tests consisted of comparing treated and untreated samples at wind velocities of 40 mph using a weight-loss method and direct dust emission measurements. It was shown that the emission of fine dust from taconite tailings, in the range of 4.5 microns to 0.85 microns, could be reduced by 99 percent using certain chemical suppressants. It was also demonstrated that a straight water spray on coarse tailings (3/4" to + 10 mesh) reduced dust emission by 95 percent. Although eight different chemicals were tested, most of the tests were made using Coherex, ammonium lignin sulfonate and sodium silicate. These same dust suppressants were used, singly and in combination on almost 75 field-test plots. The Coherex appears to provide the best results in terms of economics and durability. Wind tunnel tests on treated and untreated Cu-Ni tailings demonstrated that applications of dust suppressants reduced fugitive fine dust by better than 99 percent.

Jan 1, 1980