Search Documents

By Daniel Castelo, Ben Potter

This paper will discuss the most efficient and effective way to use shape charges when considering standoff distances and the amount of an explosive to be used. For each shape charge test that was performed, a one inch diameter copper liner of 90o was used. Different standoffs for each shape charge were tested to see which one would penetrate the deepest into rolled homogenous armor steel (RHC 44). It was determined that a standoff of three cone diameters provides the deepest penetration. In addition to testing for optimal standoff distances, the effects of overfilling as well as under filling a shape charge with explosive was tested against a shape charge with the bare minimum amount of explosive for correct detonation. These “fill” tests were all performed at a standoff of three cone diameters. Overfilling has little to no effect towards penetrating deeper into a target while under filling a shape charge has an effect of shorter penetration. C-4 explosive was the main explosive for all shape charges.

Jan 1, 2011

By Gungor Tuncer, Ali Kahriman, Abdulkadir Karadogan, Simav Bargu, Savas Gorgun, Derya Kucukbrtem, Esat Tansev

Although many research studies had been carried out in the past in order to eliminate environmental issues produced from blasting unfortunately a general approach or formula has not been established yet because of the complexity of the matter. In addition to the wave and ground motion characteristics, the complexity of blasting parameters and site factors restrict the developing of a general criterion. So experimental site-specific studies should be still done in order to predict and control blasting effects.

Jan 1, 2002

By K. Hausmann, P. A. Sashin, G. J. Prejean

Misfires caused by unreliable shock tube constructions can have significant cost implications and place field workers at serious risk during remediation. Ionomer materials, used as a subtube in shock tube constructions, provide superior hot tack strength, oil resistance, impact resistance at cold temperatures and excellent thermoformability properties. These are important features for resisting blast-throughs and ensuring blasting reliability in demanding environments, such as open pit mining in harsh environments. Superior hot tack strength, strain hardening, and excellent thermoformability properties of the ionomer materials ensure uniform powder distribution along the shock tube during construction and avoid undesired powder accumulation due to deformation or vibration during use. Oil or chemical resistance is another feature of Ionomers. This allows improved property retention in contact with oils and hence longer sleep times of the shock tube. Another feature of these highly engineered ionomers is superior impact strength at low temperatures. This plays an important role considering the resistance to fly rock impact in open pit mining operations in particular in cold climates.

Jan 1, 2011

By Eric Grigoryan, Wade Hutchison

An engineering study of 2,250 blasting damage claims from 1999 to 2008 in Tennessee, Kentucky, Virginia, Nevada, California, Georgia, South Carolina, North Carolina, Alabama, Arizona and Utah were investigated over the last decade and these investigations determine that blasting ground vibrations damage claims are valid less than 1.3 percent of the time. This study determined that valid blasting damage occurred as a result of impact damage associated with fly rock, air concussion stressing, instantaneous reverse stressing associated with ground vibration and crater zone soil shifting related stressing.

Jan 1, 2009

By David Nemir, Jan Beck

A challenge in materials science is the production of a bulk solid material from a powder precursor. One solution is to use shockwave consolidation whereby a ductile tube is loaded with the powder of interest and then surrounded by an explosive. A detonator at the top of the explosive column initiates a symmetrical high-pressure pulse that moves inward and down the tube, causing the tube to deform and the interior powders to consolidate into a dense, well bonded bulk material.

Jan 1, 2016

By Maria Sullivan

There have been many papers and articles presented over the last 60 years questioning the relevance of the 8-millisecond blasting delay window as an ‘Industry rule of thumb’. The concept of using delays between blast holes to minimise vibration is well understood and agreed upon. The means for evaluating what that minimum delay interval needs to be, for a particular site given their ground conditions, design parameters and blasting techniques, is much less established. Some sites haven’t even recognised their required minimum delay value may not be 8-milliseconds!

Feb 6, 2023

By Jhon J. Silva Castro

Blast vibration records used in mining contain unwanted information in the form of noise due to long-period drifts, background noise, and noise due to the conversion of the analogue signal to a digital signal. When recorded signals from blasting are used to find other physical variables, such as going from particle velocity to acceleration or displacement, the additional information in the vibration signal can result in inaccuracies in the estimation of the peak values and more dramatically, the results in displacement or acceleration can be nonzero near the end of the record. There are different proposed methods to clean or filter the unwanted information from the signal. All of the methods are based on finding the best fit of the record average value (baseline) and then subtracting from the record under analysis to produce the desirable adjustment. Different criteria and functions are used to define the best fit. The function to use will depend on the shape of the record average values. The main characteristic of the baseline function is that it represents a low frequency wave. Such a low frequency wave can be a periodic function or a polynomial expression of nth order. According to the order of the polynomial expression, the baseline correction can be linear, parabolic or high order. In this document the detailed procedure and the results for the baseline correction of a blast vibration record using a periodic function and a polynomial expression of different order is presented. The results show that the drift problem when displacement is calculate using velocity records increases with the increase of the distance from the blast.

Jan 1, 2015

By Catherine T. Aimone-Martin, Elena Oana Jacobs, Brent Meins

Accurate pressure measurements during underwater detonations are critical for the protection of structures and mitigating impacts to fish and marine mammals. Current guidelines that limit underwater pressures are based on past studies, many of which used sample rates of 48 and 65 kS/s (48,000 and 65,000 samples per second). These sample rates may be insufficient to accurately record high frequency, sharp rise time blast pressures. As such, pressure thresholds associated with fish and marine mammal injury or mortality may be underestimated, calling into question the pressure and sound pressure level guidelines that govern underwater blasting today.

Jan 1, 2019

By Michael Wieland

Smoke/fume measurements from rapid transitory charge reactions are not wholly comparable with thermodynamic reaction code (TDRC) results, since quenched chemical reactions yield nonequilibrium concentrations. Though the work output and major reaction products are usually rendered with minor deviations, the toxic fumes and other minor concentrations reveal some major discrepancies. Work output for charge formulations in underwater or fixture tests were theoretically resolved with work-principal models that form a rough thermodynamic trajectory. Stalled nonequilibrium concentrations are rationalized by finding the underlying quenched reaction(s). The wide relevance of the Zeldovich radical-chain mechanism that transforms nitrogen oxide was previously recognized. The work-principal model (WPM) represents reaction quenching with off-trajectory constraints to render the fumes, without noticeably readjusting the work process. When restraints that characterize the confinement are WPM tractable, the resolution of critical reaction mechanisms is worthwhile, since they remain useful, regardless of the rich, neutral or lean stoichiometry of the charge formulation.

Jan 1, 2012

By Nolan Eckroade

The demand for blast optimization within the quarrying industry calls for more effective, faster and safer methods of quantification of blast performance. Drones provide the ability to safely and quickly capture high resolution imagery of a muckpile for use in fragmentation photo analysis. Oversize material within a muckpile is an expensive and universal problem affecting quarries, especially in situations where cap rock is present. Although the amount of oversize material in a blast is a key indicator of blast performance, it is difficult, hazardous and slow to measure across an entire muckpile using traditional methods. By piloting a drone using an automated flight plan with set amount of overlap across images, the images can be processed into a single, high resolution orthomosaic image for use in fragmentation photo analysis software.

Jan 1, 2018

By W. Jiao, Y. Yongqi, R. Shan

Soft rock mines are distributed through out P.R.C. And drilling and blasting is still the main method of driving a tunnel in these mines. Traditional smooth blasting has been widely and deeply studied and put into practice in P.C.R since 1970s. But the cartridge and blast hole are both columns, the stress field in the rock around blast hole at the beginning is symmetry around hole axis, and the original cracks in the rock can be activated randomly. So serious overbreak and underbreak at the boundary of an excavation occur often, especially when the excavation is in soft rockmass, and the rates of half-hole marks are generally about 50% in medium rock, and 20-30% in soft rock in Chinese coal mines. For the sake of overcoming the situation, we have been studying directed crack blasting since ten years, and have got some obvious achievements in this respect. Slotted cartridge control blasting in soft rock is studied in this paper. Through model experiments, reasonable decouple coefficient range and slot width are gotten, and unsymmetrical dynamic strain field is analyzed. Through underground test in soft rock with a strength lower than 1OMpa in Dayan Mining Bureau, The results of which the rates of half-hole marks and the nonsmooth grades of the cut contours are 83.3% and 1OOmm respectively have been achieved.

Jan 1, 2000

By G Alan Foster

Many complaints generated from blasting operations result from the marked human response to ground transmitted vibrations and air blast effects and so many authorities have considered the regulation of blasting in terms of human response rather than, as previously, in terms of preventing damage to structures.

Jan 1, 1981

By R L. Calhoun

A paper on High Pressure Air must start with the industry accepted definition of High Pressure Air and, for the reader who is unfamiliar with High Pressure Air systems, include basic information on which type of Drilling Rigs can benefit from the use of High Pressure Air. The operation of a modern Downhole Drill must also be reviewed.

Jan 1, 1976

By James Stuart

Explosive components are common in electric power distribution systems. Basically, we use explosives either to open or to close a circuit very quickly, in order to avoid electrical catastrophe. We use explosives in these important applications, because explosive materials are compact, inexpensive, long-lived, powerful, and can be triggered instantly. A lead-alloy fuse will melt when excessive electric current passes through it. A small fuse of this type melts quickly. However, a lead-alloy fuse for high current levels must be larger, and takes longer to melt. Thus, at high current levels, a lead-alloy fuse offers inadequate protection, because electrical catastrophe might happen, before the fuse melts. We need faster-acting, explosive components.

Jan 1, 2009

By Brad Johnson

Homestake Mining Corporations' open cut operation at Lead SD. experienced a highwall failure in October of 1993. The failure released a 75' section of rock wall at the 5280' level. It came to rest on the 5200' safety bench. Since work was in progress below the failure, this rock had to be removed for safety.

Jan 1, 1995

By Gungor Tuncer, Ali Kahriman, A. Kadir Karadogan, Savas Gorgun

The environmental problems arisen from ground vibration and air blast have been faced and discussed frequently in various industries such as mining, construction, quarry, pipe line etc. where blasting is unavoidable operation. Structural damage due to ground vibrations creates great socio-economic problems for mine and quarry management as well as for the people residing in its vicinity, therefore in bench blast design, not only the technical and economical aspects, such as block size, uniformity and cost, but also the elimination of environmental problems resulting from ground vibration and air blast should be taken into consideration. With the general trend towards larger blasts in mining and infrastructure excavation, ground vibration and air blast problems and complaints have significantly increased. With increasing environmental constraints on the levels of disturbance induced by blasting operations upon nearby residents, there is an increasing need to be able to design cautious blasting with greater precision, therefore determination of maximum amount of explosive per delay for a certain distance especially in large blasts is of great importance for the elimination of these environmental problems. In another word, prediction of ground vibration components is extremely important for the minimisation of the environmental complaints. Estimating of particle velocity and other components of ground vibration with reliable approaches will give important facilities to the blasters. Although many studies had been carried out to isolate environmental problems induced by blasting in the past, a general reliable formulae has not been established yet. Due to restrictions on the complexity of ground motion, blasting and test site factors, experimental studies are still necessary for each site to minimise environmental issues. This paper presents the results of ground vibration measurements carried out during the excavation activity for contruction of an organised industrial region located nearby Istanbul in Turkey. The major rock type is granite that is encountered at this site. Within the scope of this study, in order to predict peak particle velocity level and produce a site-specific propagation curve for this site, ground vibration components were measured for blast events during bench blast optimization studies over a long period. In blasting operations; ANFO (blasting agent), gelatine dynamite (priming) and delay detonators (firing) were used as explosives. While the parameters of scaled distance (charge quantity per delay and the distance between the shot and the station) were recorded carefully, the ground vibration components were measured by means of two different vibration monitors for every event. Then, the data pairs of scaled distance and particle velocity were analyzed. The equation of scaled distance extensively used in the literature was taken into consideration for the prediction of peak particle velocity. At the end of statical analysis and evaluations an empirical relationship with good correlation was established between peak particle velocity and scale distance for this site.

Jan 1, 2000

By Braden Lusk

This paper includes results from analysis of recorded Acoustic Responses of Structures to Blasting. The analysis was performed to determine specific characteristics of sounds experienced inside homes during blast events. Data was collected in a typical house within the Boone North No.2 Coal Surface Mine in Ashford, WV which was instrumented for several blast vibration and acoustic responses. The instrumentation consists of four acoustic microphones distributed throughout the internal areas of the house and three geophones buried near the house. Two additional channels collect the trigger signal and Air Blast information. For each blast event recorded by the system, the mine blast reports were used to obtain major blast characteristics such as distance from the blast to the instrumented house, weight of explosive used, number of boreholes, delays, and other important parameters. This information allowed study the relationship between the acoustic response and the blast design. From a database of 43 records, five records were chosen for complete analysis. These records were chosen based on distance from the blast to the house, and specific blast parameters. This paper presents the result of the relationship between the frequencies and amplitudes for the entire trace of acoustic records, the response due to ground vibration (GV), and the response due to air-blast (AB). Frequency content was obtained through Fast Fourier Transforms (FFT), using D-Plot software. The records have a typical shape that permits cutting and analyzing each part of the signal with respect to GV and AB separately. Some conclusions are reported concerning the relationship between blast parameters and acoustic response of structures.

Jan 1, 2009

By J. Meissner

In this paper vibratory crack response is compared to that produced by volumetric changes in foundation soils induced by natural events. These natural phenomena include changes in the water table, changes in soil moisture, and formation of ice lenses to name a few. Previous papers have compared vibratory responses of cracks to atmospheric effects such as those produced by the passage of weather fronts and daily changes in temperature and humidity. Periodicity of these atmospheric effects is on the order of a day to half a dozen days. Thus it is possible to observe atmospheric effects with measurement over a period of weeks to several months. On the other hand, crack response produced by volumetric changes in foundation soils occurs over a period of many months and/or may be seasonal in nature if not longer in the case of drought. Thus its measurement requires long periods of observation (many months to significant fractions of a year) or observation during critical seasons. Since it occurs over long periods of time, its observation may be obscured by climatologically induced crack response. These soil volume changes are compared with climatic data to describe the correlative nature of crack response in time with the soil volume change phenomena and likely climatic causes.

Jan 1, 2009

By Dal Sun Kim, Michael K. McCarter

"Comminution (crushing and grinding) of rock materials is energy-intensive and expensive. Mucheffort has been directed to improve the efficiency of conventional milling practice, but relatively littleattention has been given to the potential benefits of blast-induced damage on comminution processes. To help assess this effect, research has been conducted at the IRECO Laboratory and the Generic Center for Comminution at the University of Utah. The objective of this research is to investigate the effect of shockinduced “crack-like” damage on rock properties and subsequent breakage efficiency for three petrologically different rock materials under laboratory conditions. In order to evaluate the effect of shockinduced damage, a quantitative measure of rock damage is needed. For this purpose, a scalar variable (0) is proposed."

Jan 1, 1993

By Pierre-Alexandre Abeel, Charles Dowding, Justin Lueker

When blasting is eliminated as a cause of cosmetic cracking, often someone will ask, “If blasting didn’t cause the crack, then what did?” This paper describes detection by remotely operated instrumentation of the new cosmetic crack that was climatologically-induced. The measurement was obtained as a part of the development of Autonomous Crack Measurement (ACM) instruments to measure micro-inch response of cracks to both long-term, climatological, and dynamic, blast vibration effects. The crack occurred in the wall of a structure that was monitored for over 29 months and as such represents one of the longest periods of ACM observation.

Jan 1, 2015