Search Documents

By Thomas A. Simpson, Yung-Kwaun Jow, Dennis L. Gamble

Construction of the $200 million Riverchase Galleria Mall in Hoover, Alabama was started in early 1984. The construction area consists of about 70 acres. The extensive building complex requires heavy concrete foundations which have to be poured during the early stages of construction and on a nearly daily situation so that contractual agreements can be met on a timely basis.

Jan 1, 1985

By Jerry Wallace

Two recent-release boulders posed serious threats to public transportation and utilities in Washington State. Both required challenging drilling and blasting solutions.

Jan 1, 1997

By Scott G. Giltner, Alex Schwenk

An iron operation sought to extend the life of the mine by conducting a major pit pushback in an area close to several public structures and the neighboring town. The result of the pushback would make millions of tonnes of ore available for mining allowing many additional years of taconite mining. This paper discusses the initial development blasts conducted for the pit pushback. For the development blasts, it was determined that no fly rock should leave the mine site and that the blast vibrations should be as low as possible, but specifically under 19 mm/s (0.75 in/s) at a nearby sewage treatment plant. One issue complicating the blast design was the variation in hole depth within any given blast. For the initial sinking shot, the hole depths varied from 6.4 m (21 ft) to 12.5 m (41 ft). In the subsequent blasts the hole depths within each blast could vary up to 5.8 m (19 ft). Various tools were employed to design the blasts to ensure there was no fly rock and that the blast vibrations were as low as possible. UAV surveys of the blast areas were conducted to provide a 3-D representation of the free faces and bench surface. The 3-D point cloud produced from this was used to measure the shape of the free faces. Once the shape of the free faces was quantified, it was possible to establish proper placement of the crest holes and develop a custom explosive load for each blast hole. In addition, signature hole analysis was performed for each blast to determine the optimum delay time that balanced the need for minimal vibration, prevent fly rock, and a well fragmented muck pile. Electronic detonators were applied to achieve the necessary control of the blast that balances these three concerns. The results of the seven blasts conducted to date provided the desired results. The peak vibration level at the sewage treatment plant for the seven blasts was 10 mm/s (0.40 in/s). The only fly rock occurred when there was a miscommunication in the blast design resulting in under burdened holes on the front row. To date, the mine has been able to safely expand the pit into an area that will add many years to the mine life. The muck piles have been well fragmented with reports from the shovel that they have all dug well.

Jan 21, 2025

By P A. Lang, J G. Ayotte, R W. Humphries

Atomic Energy of Canada Limited (AECL) has the responsibility for research, and development of technologies, for the safe and permanent disposal of Canada's nuclear fuel wastes. As part of this comprehensive program, AECL is constructing an Underground Research Laboratory (URL) near Lac du Bonnet, Manitoba, to evaluate aspects of the concept of waste disposal deep in stable geological formations. No nuclear wastes will be used in the URL program.

Jan 1, 1986

By Tyler Rockley, Cara Rosen

Blasting at a granite quarry in eastern Maryland produces elevated air blast readings that can fall into the cautionary zone for the state of Maryland environmental regulations on a semi-regular basis. When designing blast patterns in this quarry, challenging geology creates rough and uneven blast faces that can be difficult to capture with 2D laser profiling fully. Utilizing several methods known to manage high air blast results like pattern adjustments, decking, and timing changes have not achieved consistent outcomes.

Feb 1, 2020

By Tyler Rockley, Cara Rosen

Blasting at a granite quarry in eastern Maryland produces elevated air blast readings that can fall into the cautionary zone for the state of Maryland environmental regulations on a semi-regular basis. When designing blast patterns in this quarry, challenging geology creates rough and uneven blast faces that can be difficult to capture with 2D laser profiling fully. Utilizing several methods known to manage high air blast results like pattern adjustments, decking, and timing changes have not achieved consistent outcomes. Accurately capturing and modeling this geology is the key to controlling high air blast. 3D modeling and profiling by drone is the solution to understanding accurate face profiles and real minimum burdens. Using 18 months of blasting data and air blast results to establish a baseline, the comparisons between blasts designed with 2D profiling and blasts designed with drone 3D profiling show improvement in air blast levels. Additionally, shots with completed drilling were drone profiled to understand precise amounts of burden for each borehole. This 'audit' of a blast allows for custom loading of explosives, accommodating the amount of burden present on the blast face. 3Dprofiling is not a new tool in the blasting industry, but a drone alleviates some of the restrictions ground systems face. Controlling and managing air blast, as it pertains to face burdens, requires an understanding of those burdens from all angles. A drone provides that distinct level of insight. The results of this study indicate that drone profiling is managing the customer's air blast readings, allowing the customer to maintain their license to operate within the community.

By Emily Johnson, Catherine Johnson, Rachel Bauer, Paul Pitzel

Demolition projects involving explosives may incorporate cutting charges to sever columns in collaboration with kicker charges that “move” the columns out of alignment. Traditional kicker charges often involve the use of dynamite secured to the column above the cutting charge. Nitroglycerine, the main component of dynamite, causes medical problems and can be a hazard to workers on site. Dynamite can also cause fragmentation of the column and structures, resulting in potential injuries to people or leading to the possibility of cutoffs in neighboring charges. This study investigates the use of water-cased kicker charges to reduce the amount of dynamite in demolition. Water charges, traditional charges, and detonating cord charges were placed on hanging steel columns and analyzed for the fragmentation of the column and velocity of the column. A W 10 X 22 beam was hung in an underground limestone test area and allowed to swing freely acting as a severed column. Charges were attached to the bottom of the column with tape and initiated using electric detonators. Explosive charges of dynamite or detonating cord were placed in the center of a water container or directly on the column for use as the kicker charge. Tests were recorded with high-speed video and velocity was calculated using Phantom Camera Control software. Velocity and time were then used to calculate force, kinetic energy, impulse, and pressure exerted by the explosive on the column. The water charge transferred energy to the column over a larger area with no direct contact of explosive and the column. Water charges moved the column faster and with more power than traditional charges. After preliminary tests, water charges were also used as the primary kicker charges in a full-scale demolition project as a case study using 118 charges. The kicker charges successfully moved building members without creating fragmentation while using less dynamite than traditional kicker charges. Due to the success, multiple full-scale projects are being designed using water charges to show success and repeatability.

Feb 6, 2023

By Ryan Brogden

On the 5 September 2014 a road train (tractor-trailer) with two trailers carrying ammonium nitrate was involved in a single vehicle accident on the Mitchell Highway, 30 kilometers (18 miles) south of Charleville in Central Queensland, Australia. The ammonium nitrate was being transported to a mine site for use as a blasting explosive. The truck came to rest in the creek bed adjacent to a road bridge and caught fire. The vehicle burnt for over one hour before the load of ammonium nitrate exploded. Miraculously there were no fatalities; however eight people nearby sustained injuries, some seriously. The road and rail bridge over Angellala Creek were destroyed and vehicles in the nearby vicinity were seriously damaged. The truck carrying the ammonium nitrate was completely destroyed with over 2500 pieces of debris scattered up to one thousand yards (one kilometer) from the blast site.

Jan 1, 2018

By Ann Barron, Mark Abernethy

Regardless of the care exercised by a blaster, seismic and acoustic effects produced by blasting can be disruptive and alarming to many people. With the general trend toward larger blasts, increased population, and urban sprawl, as well as sensational accounts of explosives - related incidents by the news media, fear and concern often leave residents searching for damage to their property. As a result, many blasting companies today find themselves at the center of litigation at an accelerating rate. Obviously, the best strategy for handling vibration and airblast complaints is to operate in a manner that does not create grounds for them in the first place. During the bidding process, ask questions. See the actual site to perf o rm an “exposure analysis.” Collect as many facts as possible before blasting including geological issues, contractual obligations, zoning, historical use of site, disruption of daily life to local residents, demographics of the surrounding area, as well as any unfavorable public opinions or prejudices connected with local construction projects or mining operations. A consultation with local pre-blast firms may assist in tracking down previous problems in the area.

Jan 1, 2004

By Greg Wyartt

"At an Australian iron ore open-cut mine, 129 separate blast patterns (consisting of 38.5 million tonnes /42.4 million US tons, equaling 28% of annual blasted tonnes) were initiated using electronic detonators. 87 patterns were designed as per site methodology using ‘vectorial’ initiation timing sequences (blast direction and relief specified only), while the remaining 42 patterns were designed with interactive initiation timing sequences - hole by hole sequencing based on the measured site specific primary shock wave (P-wave) velocity and distance between blast-holes. The intention of this project was primarily to reduce material size presented to the crushing circuit, and also to determine if productivity benefits could be obtained by the use of interactive timing."

Jan 1, 2017

By Edward Fitch

The DOE is evaluating Yucca Mountain, Nevada as a potential site for disposal of high level nuclear waste. Yucca Mountain is located approximately 160 km northwest of Las Vegas on the western edge of the Nevada Test Site and the Nellis Air Force Range. An exploratory tunnel has been constructed through Yucca Mountain for site characterization. A controlled drilling and blasting technique, smooth wall blasting, was used to excavate the TBM starter tunnel and alcoves off the main tunnel to provide areas for scientific investigation. Fundamental to the blasting program has been the use of two blast design equations used in concert to minimize blast damage to the surrounding rock mass. The first of these equations was developed by Roger Holmberg and estimates near-field peak particle velocity that is the basis for minimizing blast damage to the host rock. The second of these equations was developed by B. H. Sanden and provides bore hole pressure estimation which allows controls to minimize crushing of the rock mass along the perimeter yet allowing enough force to create tensile failure between perimeter bore holes. This is key to the smooth wall blasting technique. To date, essentially the same controlled drilling and blasting program has been in place for all excavation requiring controlled drilling and blasting at the ESF. The controlled drilling and blasting program uses an iterative process to achieve continuous improvement in the blast rounds. This involves interaction between Architect and Engineer (A/E), Constructor, and Testing Coordination O&e (TCO) to ensure each blast round successfully meets the expectations of affected participants. The A/E requested that the TCO provide validation of the near-field peak particle velocity estimation under the Construction Monitoring Program. Data gathered under this program were reduced by statistical analysis and used to verify blast design parameters and provide a site specific blast damage relationship.

Jan 1, 2000

By Adam T. Young

This paper will describe the process of using low density bulk emulsion as a means to maximize the production of an oversize or “rip rap” aggregate size range (8 inch to 72 inch) that the quarry customer has a market demand for. It will also discuss the pre-blast and post-blast metrics used during the product trials and evaluation.

Jan 1, 2017

By Braden Lusk

Vibrations as a result of blasting practices in mining engineering are a complex phenomenon controlled by many variables. Mine blast vibration modeling and prediction is becoming more important as a consequence of the general negative perception of mining activity by the public. Many communities (all over the world) close to mining activity often complain about airblast and vibrations produced from blasting activity. It is important for the mining industry to have tools and understandable methodologies to model and predict blast vibration. These tools can then be used to control vibration at neighboring structures.

Jan 1, 2013

By Takeo Ueda, Masashi Nakano

We have developed a new blasting system remotely controlled by an electromagnetic firing method, which has proved advantageously applicable to sites where rapid tidal current or deep water may cause serious troubles in underwater blasting operation by a conventional method.

Jan 1, 1983

By Felipe França Sitonio

Parameter’s control of explosives used in blasting operations have become more relevant over the years, bringing a better understanding of detonation performance. Giving into consideration that bulk emulsion density’s variation reflects directly on blasting results due to its importance in product sensitivity and velocity of detonation (VOD), blast designs are conducted assuming that cup density measurements are reliable and explosives gassing agents will perform as per specifications. Nevertheless, confinement conditions in boreholes like temperature, presence of water and surrounding circumstances of rock mass are often neglected on predictive modelling and off-site measurements. This paper describes the assembly of a device equipped with pressure sensors and its utilization in confined boreholes of an open pit mining operation, aiming to obtain in situ monitoring of density variation in several explosive columns. After we developed a software to get and process data of a hardware prototype and the device functionality was validated in water, oil and quarry mining experimental trials, 7 of 291 boreholes in a gold mine operation were chosen to be monitored with two probes each, placed at the top and at the bottom of the explosive column profile. The results obtained enabled a comparison between the bulk emulsion density variation when acting in different environments, since we selected boreholes with diameter of 101.6 mm (4 in) and 139.7 mm (5.5 in) and some with presence of water. Besides the increase of explosive density with depth related to hydrostatic pressure increase, we found an overall error of 6% in cup density measurements when compared with sensors placed at the bottom of boreholes and 2% when compared with sensors placed at the top of explosive column. These findings provide detailed insights into how bulk emulsion explosives behave in different circumstances including depth and borehole diameter, giving the opportunity to re-evaluate blast design parameters such as its geometry, sequence pattern, charging profile and explosive composition.

Feb 2, 2020

By G. C. Naveen

Punatsangchu Hydroelectric Project Authority is constructing 1020 MW underground hydroelectric project in Bhutan. The project envisages construction of concrete dam, Desilting Chamber, Head Race Tunnel, Power House Complex and Tail Race Tunnel. Tunneling is one of the major activity in any underground projects as they are driven for multiple activities. By and large the tunnels are a major part of connecting networks from surface to caverns/underground working sites. Many tunnels in hydropower project are part of water conducting systems and one such important tunnel is the Tail Race Tunnel in this project and had to be excavated in thinly foliated rockmass conditions by D&B method. The rockmass is traversed by three to four joint sets and few minor shear seams. Rock Class “Q” values were between III and IV. Tunnel was excavated by full face parallel hole drilling blasting method. The adopted blasting method consisted of drilling 45mm (1.77 inch) diameter holes to a depth of 2m and the drilled holes were charged with 40mm (1.57 inch) diameter cartridge explosives and charges were initiated with half second non electric initiators. The perimeter holes were drilled at closer spacing of 30cm (1 feet) and alternate holes were charged using 32mm (1.23 inch) diameter cartridges explosive. Low dipping foliation joints present in the rockmass tend to slab in crown portion and erratic occurrence of intrusive bodies lead to unpredictable behavior of rock mass posing a major challenge for the safe excavation. Stability was a major issue through controlled blasting under constant supervision too could not limit the overbreak in certain weak rockmass conditions thereby exposing cavities of about 2.5m (8.2 feet). The stabilization of these cavities and handling the overbreak due to rockmass condition was time consuming and warranted additional supports. With systematic measurements and controlled blast designs the Horse Shoe Shaped Tail Race Tunnel of 9.1 m (29.85 feet) diameter and 304m (997.37 feet) length to connect with Downstream Surge Gallery of 314m (1030 feet) length, 18m (59 feet) wide and 58.8m (193 feet) height in thinly foliated and jointed biotite gneiss rockmass was successfully excavated.

By Raj K. Rajamani, Solomon A. Tucker, Michael K. McCarter

"In a study aimed at exploring possible improvements in operating performance at an Open Pit Copper (OPC) mine in the western U.S., the impact of blast energy changes on crushing performance was evaluated. OPC feeds its 3-stage crushing plant in 12-hour-day shifts with skarn ore from three domains: Pit_B (B), Pit_S Low-Grade (SLG) and Pit_S High-Grade (SHG), in the blending ratio 1:1:1 (B/SLG/SHG). Thecrushed product is fed to a 2-stage ball mill circuit. "

Jan 1, 2017

By P D. Katsabanis, K Steeves, D Dombrowski

Accurate electronic detonators with firing time accuracy within 100 microseconds of the nominal have been used to control blast results in terms of fragmentation, vibrations and wall control. Axisymmetric experiments and experiments utilizing small benches have been conducted in order to calibrate a numerical model under development and examine the influence of delay interval on wall control, fragmentation and vibrations. The results obtained so far indicate definite advantages of precise timing in reducing back break and wall damage. Fragmentation is affected by the delay interval and high speed film observations and measurements indicate that the delay interval should allow the damage zone from each blasthole to be fully established prior to the detonation of the next borehole. Studies on vibration control demonstrated that vibration synthesis work using signature shots can only be of use if accurate delays are employed.

Jan 1, 1995

By Eric Reale

The New York City Department of Environmental Protection (DEP) is currently building City Water Tunnel #3 beneath the city. The purpose of this tunnel is to improve water distribution to the city and to allow the DEP to inspect the older tunnels and make the necessary repairs. These older tunnels have been in continuous operation since the early 1900's. Construction on the Third Tunnel is planned in four stages. The Nelson Street Shaft, which is the focus of this paper, is part of the second stage.

Jan 1, 1989

By Patricio González Santis, Jacopo Seccatore

This paper documents drilling and blasting activities from gold mining in Ecuador and Chile. First, are described the outdated and often non-rational techniques employed by miners, to provide a general framework of the current methods. Then, it is shown what can be improved and how the current methods can be modified. Finally, are shown some field applications and the comparisons of the results obtained

Feb 1, 2020