Search Documents

By S. J. Neethling

"Flotation is a complex process with many factors that influence the performance of a cell. This paper examines the impact of several key variables on the performance of flotation cells. The study makes use of a simulator for the froth phase of the flotation vessel, as the main purpose of this study is to separate the impact of different variables from one another.In experiments it is very difficult to separate the effect of variables from one another as a change in a singe input parameter, such as air rate, invariably also affects many of the other key variables, such as bubble size and bubble bursting rates. This interaction between variables makes it very hard to experimentally separate the impact of, for instance, the air rate from that of bubble size or bursting rate. In the simulator, though, it easy to make independent changes to these variables.In order to achieve this a base case simulation that is typical of many of the rougher cells found in sulphide flotation circuits was carried out. Four key variables, air rate, incoming bubble size, surface bubble size and the fraction of the bubbles flowing out of the cell unburst, were varied in order to obtain the system’s response.The most significant results were obtained when the bubble size was varied. An increase in the incoming bubble size has the effect of reducing the pulp zone recovery, but increases the froth zone recovery. If it were possible to vary the incoming bubble size without influencing the overflowing bubble size, the impact of the change would be unclear because of these two competing effects. The effect of a change in the overflowing bubble size has an opposite effect on the froth recovery, with larger bubbles resulting in lower froth recoveries."

Jan 1, 2003

By Victor Avdokhin, lvan Kovlekov

"Studies of the process of concentration of gold-containing sands and technogenic resources show that the main reason of gold losses is misbalance between size of gold particles and degree of roughness of mineral bed. This results in free circulation of small gold particles in pores with following washing off the particles from the bed by turbulent flows.We elaborated design of magnetic sluice, intended for improving efficiency of recovering fine gold by optimizing magnetic field of a magnetic system on the base of forming catching coat from magnetic mineralsThe magnetic sluice includes trough-shaped body from magnetic-conducting material. On the bottom of the trough, magnets are placed, and opposite poles of the magnets are oriented outwards. Thickness of the bottom is determined to be sufficient for locking magnetic lines of force of the magnets on each other. The magnets of rectangular plate shape are placed on the rough bottom, covering the whole surface or with spare areas; the magnets are placed across the trough with alteration of rows with the same pole orientation."

Jan 1, 2003

By B. C. Qi

"In water treatment, flocculation or coagulation with aluminium or ferric salts has been widely used for many years to remove natural organic matter (NOM), including humic acids. However, the adsorption of NOM to aluminium hydroxide flocs during conventional coagulation/flocculation processes is very complex, with the flocculation of aluminium hydroxide particles and the adsorption of NOM molecules on flocs occurring simultaneously. Any effect on the surface characteristics and micro-structures of the humic acids and aluminium hydroxides could affect the adsorption efficiency.It has been widely observed that if a reaction system (liquid-liquid or liquid-solid) is exposed to an ultrasound field, under appropriate conditions, a variety of physical (emulsification, aggregation/flocculation) or chemical (the production of radical and exited species; single electrotransfer) actions may be activated. Though the ultrasound effects have been used in biological and chemical decontamination in many conventional environmental protection practices, the idea to explore the ultrasound effects in the removal of humic acids by preformed aluminium hydroxide flocs is relatively new. In this paper, the effect of an in-situ ultrasonication on removal of the humic acids extracted from the acidification fermentation of lignocellulosic residues, by a preformed aluminium hydroxide, was evaluated; the effect of ultrasonication on the surface complexation of the humic acids with the preformed aluminium hydroxides was investigated."

Jan 1, 2003

By Kal Sastry, Anshuman Prasad

"Agglomeration of fine iron ore concentrates is carried out in two steps:Balling, which refers to the production of green pellets by tumbling moist fines powders in drums, discs, or cones, and Induration, which refers to the subsequent thermal treatment of the green pellets in straight grate or grate-kiln systems.This paper addresses computer simulation of balling or green pelletization step. The process of agglomeration from a mechanistic point of view can be described as the transformation of moist feed to well-formed species or pellets. The moist feed is composed of fines of infinitesimal size while well-formed species are of finite size and number. These well-formed species undergo changes in their size and number through different mechanisms of agglomerate formation and growth. Nucleation, coalescence and layering are the three main mechanisms that describe the formation and growth of granules during an agglomeration process. A population balance equation enables quantitative description of the evolution of agglomerate size distribution due to the occurrence of each of the mechanisms.A numerical solution for the population balance model is necessary and is obtained by the use of a sizediscretization approach. The numerical solutions provide a suitable basis for the analysis of the agglomeration process. Also a coalescence kernel has been introduced that is capable of describing the simultaneous occurrence of nucleation, coalescence and layering mechanisms. The effect of feed moisture has been described using a moisture factor with an exponential functional dependence on the moisture content. The effect of the feed to seed ratio is modelled by the introduction of a crowding factor. It was assumed that only the feed particles which are much more in number experience a crowding or restricted in space interactions effect. A computer simulation program has been developed with MATLAB as the simulation language."

Jan 1, 2003

By Peter N. Holtham, Geoffrey J. Lyman, The University of Queensland, Matthew S. Brennan, Vijay Subramanian, Rui X. Rong

"The cyclone would have a claim to be the commonest, least understood and most abused piece of mineral processing equipment available for study by researchers. It has certainly generated its fair share of publications – 1,000 in the last 60 years would be a fair estimate. However this remarkable degree of interest and scale of investigation is not reflected in our understanding of how they work; cyclones are still installed inappropriately and run poorly, which suggests that there are still things to learn about this deceptively simple process.In mineral processing there are two broad classes of cyclone: the hydrocyclone, used in classification, thickening and dewatering, and the dense medium cyclone, used for concentration by density. Although rarely studied together, the laws of physics presumably apply equally to both and so it seems that there would be interesting things to learn by considering them as a single class of device. The good news is that in recent years there have been spectacular advances in the computational and measurement tools available to study these devices, including computational fluid dynamics (CFD), tomography, and laser doppler anemometry (LDA), and some good progress has been made in an understanding of the fundamental principles involved.The JKMRC has made many experimental studies of hydrocyclones and DM cyclones, leading to useful empirical models. However some recent CFD and tomographic work, in association with work of other institutions, has thrown important light on the workings of these processes. Progress has also been made in novel designs of cyclone to achieve improved separating efficiency, based on an attack on the subprocesses believed to contribute to inefficient operation. This paper describes the work to date.Modelling of the dense medium and classifying cyclone was conducted using the Fluent computational fluid dynamics code. Three phase simulations of the dense medium application (air/water/medium) showed appropriate medium segregation effects but over-predicted the level of segregation compared to segregation measured by gamma-ray tomography. This is believed to be because the basic Algebraic Slip mixture model in Fluent does not model any back-mixing of the dispersed phase due to turbulence."

Jan 1, 2003

By Shailin Lalloo, Allan B. Nesbitt

"Gravity separation by centrifugal equipment, particularly in the mineral processing industry is a novel approach of optimising product recovery. The manufacture and sale of centrifugal equipment by recently established companies is now beginning to have a significant impact on the industry. Some benefits of operating at increased gravity include: reduced environmental issues, a shorter lead time, lower capital cost and improved recoveries of elemental mineral before entering the grinding circuit.Of topical discussion is the use of centrifugal separators for the recovery of less valuable minerals that will form a greater proportion of the feed compared to traditional scalping circuits where the gold content is extremely low. This ultimately results in the centrifugal system having to have a greater mass pull. In addition, the relative density difference between gangue and valuable mineral is likely to be less and therefore modelling and optimisation of this separation process will be necessary. Some researchers have muted using fluidisation models to model the forces present in the separation zone of a centrifugal separator2. It is not unusual for the manufactures of centrifugal separation equipment to use fluidisation terminology to describe what happens in the separation zone. Most fluidisation models are based on the empirical/classic relationship between superficial fluid velocity and voidage postulated by Richardson and Zaki. However, no researcher has proved the effectiveness of this relationship in an increased gravity Environment."

Jan 1, 2003

By Johan F. W. Kock

"Hearing loss due to excessive noise exposure is the most prevalent industrial disease. It is ranked on the World Health Organization’s (WHO) priority list for major work related injuries. Uncontrolled noise not only has a physical effect, but is also a psychological hazard affecting the performance and well being of man. Noise induced hearing loss (NIHL) is irreversible, yet it is preventable. The first defence against noise (noise control engineering) is a high priority in the mining industry. Second defences should be a last resort when the engineering control of noise is inadequate. Hearing conservation programs and the use of conventional hearing protection devices seem to have failed in the prevention of noise induced hearing loss. If compensation payouts that quadrupled in the past ten years are used as a barometer for the success of existing hearing conservation programs, then new strategies and technologies need to be investigated. The best practice Hearing Protection Device (HPD) may be seen as the minimum standard for second defence noise control.Conventional hearing protection is widely applied, but also misused in the industry as well as in the mining sector. Empirical research results, ownership, general attitudes of workers as well as qualitative aspects will be explored. The paper provides reasons, evidence, case studies and strategies regarding the best practice hearing protection philosophy (the Noise Clipper Model) as implemented in the Implats Mining Group. Worldwide tendencies towards custom-made HPD’s, findings that indicate improvements in hearing conservation programs and finally the successful application of Custom-made Hearing Protection Devices, will be outlined."

Jan 1, 2003

By Peter N. Holtham, Mary M. Ng

"Resistivity measurements of minerals in the laboratory are commonly made with a low DC voltage source. Common test voltages specified in the ASTM Standard D257 are 100, 250, 500, 1000, 2500, 5000, 10000 and 15000 V, however 100 and 500 V are the most frequently used. Resistivity results obtained in the laboratory have been used to infer the electrical behaviour of minerals undergoing electrostatic separation. However because the voltages employed in electrostatic separation in the plant are of the order of thousands of volts, typically greater than 15000 V, whether the laboratory results are applicable as a predictor of plant performance is a critical question. It is unclear whether resistivity values taken at a low voltage are characteristic of those seen in electrostatic separation, in which the minerals are exposed to a much higher voltage. No definitive answer could be found in the literature.In this work, the resistivities of zircon, rutile and ilmenite were measured in a corona field for the first time. The measurement principle was based on a technique developed to measure fly ash resistivity in electrostatic precipitators, however the test apparatus and findings are novel.Resistivities of rutile and zircon were found to be easy to measure. The values measured in a corona field were several orders of magnitude less than those obtained with a dc voltage of 100 V. Evidence of back corona was observed with zircon. When the voltage drop was greater than the sample layer could withstand a localised electrical stress developed, resulting in a voltage breakdown, at which point a sudden surge of corona current (back corona) was detected in the sample layer. Rutile, on the other hand, exposed to the same conditions as that of zircon (i.e. same temperature and applied voltage) did not exhibit any sign of back corona. Its resistivity across the range of test voltages (14 to 33 kV) remained fairly constant."

Jan 1, 2003

By Ponisseril Somasundaran, H-L. Chen, University of Athens, D. R. Nagaraj, Zhonghua Pan, Jing Wang

Gums are often used as depressants for talceous gangue minerals in the flotation of nickel and platinum bearing ores. However, the mechanisms of gum adsorption on talc are not clearly established. In this work, adsorption of guar gum at the talc-solution interface is investigated using spectroscopic and allied techniques. Guar gum adsorption on talc is not affected significantly by changes in solution conditions such as pH and ionic strength. Electrokinetic studies showed that guar gum decreased the negative zeta potential of talc but did not reverse the charge. Fluorescence spectroscopy studies conducted to investigate the role of hydrophobic bonding using pyrene and dansyl probes showed no evidence of the formation of hydrophobic domains at talc-aqueous interface. Urea, a hydrogen bond breaker, reduced the adsorption of guar on talc to the same extent as that for guar/alumina system, in which hydrogen bond plays an important role. All of the above results suggest that one of the main driving forces for guar adsorption on talc is hydrogen bonding rather than electrostatic or hydrophobic force.

Jan 1, 2003

By Atsushi Shibayama, Toyohisa Fujita, Wan-Tai Yen, Ke-jun Liu

"A gold has been leached with ammonium thiosulfate solution and several leaching conditions have been studied. The leached solution has been recovered by solvent extraction and the optimum conditions have been investigated.SUMMARYIn this investigation, a sponge gold sample (99.92% pure) has been leached with ammonium thiosulfate solution. The effects of CuSO4, (NH4)2S2O3, (NH4)2SO4, NH4OH and retention time on the gold leaching % (extraction %) and thiosulfate oxidation % (consumption %) have been studied. The copper ion acts as a catalyst in gold dissolution. On the other hand, it also accelerates oxidation of thiosulfate (consumption). It was found in this study that the best gold extraction condition was obtained at 43.2 ks with 0.8 – 1.0x103 mol/m3 (NH4)2S2O3, 30 mol/m3 CuSO4, 2.0 – 3.0x103 mol/m3 NH4OH, 0.4 – 0.5x103 mol/m3 (NH4)2SO4, pH 10±0.2 and 150 rpm. The thiosulfate oxidation was about 15% of the initial concentration."

Jan 1, 2003

By James Y. Oldshue

"Very seldom is it possible when contacting a gas with a slurry to measure the dissolved gas concentration in the slurry, and even were it possible, seldom are equilibrium data available with a suitable Henry’s law constant.In general, by assuming a reasonable value for the dissolved gas concentration in the slurry and a corresponding equilibrium gas partial pressure P*, Kga values can be calculated for the pilot plant and scaled up. Then, with the same P* value at various reaction conditions, a mixer can be designed which is quite satisfactory, having a reasonable design factor for full-scale performance.We will take as an example a slurry of a known solids composition and use a continuous 4 tank system. By assuming a percentage saturation of the dissolved gas in the first tank, the dissolved gas concentration can be obtained in the other three tanks. It usually is possible to measure the off-gas composition in each of the 4 tanks. If the top of the tanks is connected in the form of a multi-compartmented horizontal autoclave, then a modified top off-gas composition in each compartment must be used."

Jan 1, 2003

By Dave Deglon

"The Western Cape Mineral Processing Facility (WCMPF) is a collaborative educational initiative between the Departments of Chemical Engineering of the University of Cape Town, the University of Stellenbosch and the Cape Technikon. The primary objective of the WCMPF is to facilitate the education, development and graduation of suitably qualified engineering graduates and diplomates for the mining industry. The WCMPF consists of academics and Technical Officers in the Departments of Chemical Engineering of the three tertiary institutions. The Technical Officers are usually metallurgists, with several years of industrial experience. The main objective of the Technical Officers is to improve the practical education of mineral processing students. In addition, the Technical Officers are responsible for organising an annual mineral processing student field trip for students from all three tertiary educational institutions. In recent years the WCMPF has embarked on a number of additional initiatives aimed at improving the quality of mineral processing education. These include the development of several new pilot plant practicals, an initiative in pyrometallurgy, the introduction of novel ‘end to end’ or ‘integrated’ practicals and the use of mineral processing simulation packages to complement the practical training.The WCMPF has been functioning for well over a decade and, by virtue of this, might be considered a successful collaborative educational initiative. The WCMPF has played a key role in the education of over five hundred mineral processing graduates and diplomates. During this time period, the WCMPF has gained a body of internal knowledge which might be of benefit to other educational institutions, viz."

Jan 1, 2003

By Genrich A. Denisov

Principles of ecologically friendly geo-technologies construction are formulated on the basis of the works of the leading scientists in the field of rational processing of mineral resources of the Russian Academy of Sciences. One of these concepts is a new direction in rotational disintegration of mineral and technogenic raw material with the purpose of effective subsequent enrichment. A large amount of practical experience has been accumulated in the industry on selective destruction by application of vibrational method on initial material with consideration of its physical-mechanical properties and mineral structure. This method is successfully realised in a conic inertial pulverisation devices constructed by Mekhanobr Institute (St.-Petersburg). A new construction of conical-inertial pulverisation with a modification of disintegration force has been developed recently at Mekhanobr Institute. It allows, in some cases, to increase selectivity of subdivision and to avoid over-disintegration. Advantages of “wet” subdivision methods in conic inertial disintegration devices are proved. The efficiency of such subdivision can be increased due to rational use of the phenomenon of a dislocation-dynamic diffusion. Its advantage is proved by the effect on disintegrated material by frequency-modulated variable electrical fields of low power. It was shown in industrial conditions, that the productivity of the spherical mill can be increased by 10 %, and that it also prevents ecologically harmful surface active substances (SAS) in milling zone and it reduces the dust content in the air. The techniques of tentative estimation of efficiency of various proceedings technogenic materials and their classification are created. The scientific fundaments of rational, ecologically friendly technology of processing and regeneration of various kinds of technogenic raw material are developed. A number of effective technologies on processing of wastes is developed and inculcated in concentration factories and metallurgical factories.

Jan 1, 2003

By Knut L. Sandvik, Erik Larsen

"Estimated global solar energy demand in 2001 required approximately 5,500 tons of silicon feedstock. This required 65,000 tons of quartz. If the trend continues, the solar energy demand in 2010 would require approximately 30,000 tons of silicon feedstock and 350,000 tons of quartz, although the need for quartz probably will be lower than this due to higher solar cell efficiencies, larger and thinner wafers, more extensive recycling of waste material and new routes for the production of silicon feedstock. The raw material requirements for the production of metallurgical-grade silicon are most likely to change. This may favour increased beneficiation of primary raw materials in the future solar cell production chain.SOLAR CELL PRODUCTION CHAIN SCENARIOSThe major problem concerning solar cells is the production costs. Electricity produced from fossil fuels and hydropower plants are currently much cheaper than the electricity produced from solar cells. Also, limited availability of silicon feedstock for the production of crystalline silicon solar cells is considered a major threat to the further growth of the PV industry. The present route for solar silicon feedstock goes from quartz, through metallurgical-grade silicon (MG-Si) and to electronic-grade silicon (EG-Si). The reject from the EG-Si production are further processed into wafers and solar cells. This situation is not satisfying, however, because it has created a silicon feedstock shortage and a PV energy price that is not competitive in a large scale.Crystalline silicon solar cells are the most important solar cells manufactured today. This will most probably remain the situation the next decade. Also, the future silicon ""feedstock"" is most likely not reject from the production of electronic-grade silicon, as it is today. There will probably be a more direct solargrade silicon route, excluding the very expensive electronic-grade silicon ""detour"". Quartzite has been regarded as the most suitable primary raw material used in the silicon solar cell production chain. This may change as the raw material requirements for the production of metallurgical-grade silicon are most likely to change. In addition, quartz or other silica-containing minerals from other rocks may be of a higher purity or contain lesser amounts of the most harmful elements. This favours increased beneficiation of primary raw materials in the future solar silicon feedstock production chain"

Jan 1, 2003

By Hamid-Reza Manouchehri

"The triboelectric charge attributes of some silicate minerals (i.e., feldspar, quartz and wollastonite) after contacting different triboecharging medium made of different materials were studied. The charge acquisitions by different size fractions of minerals were monitored and accordingly the energetic work function values, i.e., the main parameter determining the entity of triboelectric charges acquired by mineral grains, of the examined minerals were estimated. Moreover the separation behavior of different size fractions of these minerals through the electric field of a laboratory free-falling separator when the mineral grains are charged by different tribochargers were observed and considered as the electrical separation potential of the examined minerals.Furthermore, the role of adsorption of different chemical species on triboelectric charge characteristics and charge acquisition of mineral samples were described from theoretical point of view and the effects of some chemical reagents on triboelectric charge acquisition of the examined minerals were studied. In addition the separation behavior of chemically conditioned quartz, feldspar and wollastonite minerals, using different anionic and cationic reagents, through the electric field of a free-fall electrostatic separator before and after chemical conditioning were monitored.Finally an attempt was made to translate the findings from single mineral systems to a complex silicate ore, containing mainly of feldspars, quartz, and wollastonite. Different separation tests under various conditions were conducted to this complex silicate ore. Before passing through the separation device, the ore sample was conditioned by different cationic and anionic reagents and then was triboelectricaly charged by different tribocharging medium in order to find the effective reagent and tribocharging medium for separating silicates. Besides the role of temperature and humidity of the surrounding ambient in separation behavior were considered."

Jan 1, 2003

By Jeremy Bosman, Niel Lourens

"Cyclones are used in four main applications in primary wet heavy mineral processing plants i.e. upfront desliming, densifying, and concentrate stacking and tails deposition.UPFRONT DESLIMINGMany heavy mineral ore bodies are associated with high slimes varying from 15 to 60%. The increased viscosities arising from the slimes impact negatively on heavy mineral recovery in the spiral plant. Recoveries can be reduced by up to 10%. Cyclones have proven to be able to remove slime efficiently with acceptable loss of valuable heavy mineral in the overflow. For low slime applications, typically below 25%, it is possible to achieve the desired results using a single stage of cyclones, whilst for higher slimes, two stages of cyclones are required. The overflow of the primary stage is retreated through a second stage to minimize heavy mineral loss."

Jan 1, 2003

By Jian Zhang, Yongfu Yu, Fuguang Zhang, Liping Che

There is one large-scaled iron ore deposit in Inner Mongolia of China, but it is very complex which includes about 170 types of minerals and 71 elements. The hematite, magnetite are mainly iron ores. It is difficult that the iron mineral can be separated efficiently by common dressing methods due to the complexity, and the iron concentrates in the mineral processing factory contains many foreign substance such as K, Na and Si so that the process in iron mill is influenced because of the foreign substance, so it is vital reducing the foreign substance.

Jan 1, 2003

By Kazimierz St. Sztaba

"Mineral processing – the first technological stage of utilization of mineral – has a very long history. In particular, it revealed and reveals the continuous development and perfection of technological operations and process organization, comprising not only new design solutions and exploitation procedures but also, for example, perfected systems of control and automation as well as methods of process description and result evaluation. During the recent decades the attitude to mineral raw materials was clearly changed, both to the primary ones, i.e. minerals, and to the secondary ones, such as side products and waste, formerly considered useless and at present more commonly used. This results both from the appearance and growth of demand for more and more numerous components of mineral raw materials and also from the necessity of protection of natural resources, constituting the integral part of the system of sustained development of society.These circumstances, and especially the requirements concerning gaining some components which cannot be separated by means of “classical” (used for many years) technological processing operations and aiming at increasing the technological procedures, evoked the necessity of using new technological solutions, applying other basic operations, also the ones characteristic so far for other processing technologies, i.e. chemical, biotechnological and others.These development tendencies, in general commonly perceived, allow us to formulate an opinion that the former state of tasks and processes of mineral processing is being transformed into a qualitatively new form. It can be assumed that this process was signaled by a situation in which, due to the growing role of technological operations based on physicochemical phenomena (flotation and others), magnetic and electrical ones, etc., one should have observed that the former term of “mechanical processing” became inadequate for the real content of the notion determining the discussed stage of mineral utilization, so the adjective “mechanical” disappeared in most languages."

Jan 1, 2003

By M. Wright, A. H. Mwale

Opportunities to promote enhanced eco-efficiency (i.e. the simultaneous improvement in economic and environmental performance) for the minerals industry exist across the whole value chain. However, given the current operational models of major companies within the industry, and their focus on refining of primary ore bodies, it is important to understand where such opportunities might lie within minerals beneficiation, as it is here that major environmental pressures are felt. This paper examines the combination of unit technologies in a minerals beneficiation train, and explores the inter-relationship between energy input and water consumption for a given mineralogy and product recovery, as these are two critical environmental issues which affect the overall viability of many minerals plants. In particular, we review constitutive relationships for each of the sub-processes of comminution, flotation, and tailings dewatering, and suggest how these might be integrated into a unified hybrid model, with particle size distribution as the key design variable. Such a model can then be used to explore the trade-offs between different performance objectives (be these technical, economic or environmental) as part of a multiple-objectives optimisation exercise. In this way, it may become practical to envision situations in which concentrate grade and recovery are sacrificed, marginally, in order to reduce energy demand in comminution, and improve overall water recovery. In addition, this work provides a useful baseline against which to analyse the potential for dry processing. This becomes more relevant as the industry commits to advancing the sustainable development agenda in the face of the increasing life -cycle costs and impacts of minerals processing operations, coupled to declining ore body grades, and the desire to maximise recovery of minor and trace elements. Some specific observations for copper are offered, supported by operational data from Zambian copper mines.

Jan 1, 2003

By Wang Xiaotie, Yu Yongfu, Che Liping, Zhang Fuguang

The flotation process of native Rare Earth minerals such as bastnasite, monazite, mixed minerals of bastnasite and monazite, using the new effective collector Dh was studied in this paper, respectively, and the flotation properties are described. The good qualities of the new collector Dh were revealed through comparing with other collector of Rare Earth minerals. The test results of different ore samples show that at moderate pulp pH (8.5-9.5), Rare earth minerals can be effectively separated from barium, calcium and silicon bearing intergrowth minerals (barite, calcite and silicate minerals) and high quality Rare Earth concentrates can be obtained successfully by the new collector Dh, acid silica gel, turpentine and reagents fitting together rationally. In order to determine optimum technical conditions, the effect of pulp pH, pulp temperature, pulp density and the effect of dosage of reagents (Dh and acid silica gel) on the flotation were investigated in the test.

Jan 1, 2003