Search Documents

"The Merensky Reef is a platinum group minerals (PGM) bearing reef in the Bushveld Igneous Complex in South Africa. The reef has been treated by bulk PGM and sulphide flotation with the aim of maximisingthe valuable minerals recovery and gangue minerals rejection.Synthetic water with a calcium concentration of 80 ppm and 500 ppm was prepared and the flotation results obtained were compared to a simple electrolyte in order to determine the effect water quality has on pentlandite and pyroxene surface alteration and, ultimately, floatability. During the study, the possible effect of interactions between the minerals investigated and Ca2+ ions in the presence of sodium isobutyl xanthate was studied at pH 6 and pH 9 by means of zeta potential determinations, microflotation tests and ToF-SIMS analysis.The results obtained on 1:1 pentlandite-pyroxene mixtures showed that the quality of process water plays an important role in flotation. The flotation recoveries of pentlandite and pyroxene were lower in synthetic process water compared to those obtained in a simple electrolyte solution."

Jan 1, 2003

By S. K. Kawatra, S. J. Ripke, T. C. Eisele

"An estimated 600,000 tons of bentonite clay are used annually in the U. S. as binder for production of iron ore concentrate pellets. Since this is a significant cost item for the plants, and the addition of bentonite to the pellets contributes undesirable silica into the finished pellets, there is considerable incentive for finding methods to reduce bentonite use. One way to reduce bentonite levels is to selectively use those bentonites that are most effective in this application, so that a lower dosage will still produce a sufficiently strong pellet. Unfortunately, there are no satisfactory methods available for accurately predicting which bentonites are actually most effective, short of using them to actually make pellets. One of the popular methods for attempting to evaluate bentonites is the “Plate Water Absorption” (PWA) test. While some plant operators accept the PWA results as indicating the relative quality of bentonites, others disagree and claim that, over a fairly broad range of values, PWA does not correlate with bentonite performance.Since both Ca+2 and Mg+2 ions are known to reduce the swelling and water absorption capacity of bentonite, it was believed that the presence of these ions in plant recycle water could be changing the bentonite performance. Since the standard PWA test uses only distilled water for its measurements, it could not detect these effects. Experiments were therefore carried out on a number of different bentonites using a modified PWA tests, with plant recycle water replacing the distilled water. These experiments showed little effect of the plant water on the PWA value, and chemical analysis of the water showed that the levels of dissolved salts were quite low.Water and accompanying salts were then extracted from a magnetite concentrate filter cake by rinsing with distilled water. Analysis of this water showed an extremely high level of dissolved salts, particularly salts of calcium and magnesium. When concentrations were compared with the recycle water from the plant filters, it was determined that levels of Ca+2 and Mg+2 retained in the filter cake were over 500 times higher than levels in the recycle water. This extreme elevation of soluble salts in the filter cake is believed to be due to adsorption of these ions into the electrical double layer of the magnetite particles."

Jan 1, 2003

By N. Raeis Hosseiny, S. H. Bassir

"Chador-Malu iron ore is one of the most important iron mines of Iran.About 98 percent of Fe in the ore is in shape of Magnetite, Hematite, Martite, aqua oxide of Iron and the other irons are with ferrous silicates, actinolite, cholorite and ferrous dolomites. 1% of Fe has replaced in pyrite. The phosphor distribution in the ore is non-hemogenous and its average in the whole of the deposit is 94%. It is in shape of Apatite.This mine contains considerable phosphor, which makes it useless for metallurgical uses. At this mine the phosphor is reduced in the iron ore at two steps. At the first step, magnetic part of the ore is separated from the gangues and phosphors by magnetic separator. At the second step, the ore is enriched by the flotation methods. Experimental flotation methods to obtain the optimum conditions are as follows:• Effect of Starch as Hematite depressant with ATRAC as Apatite collector• Effect of Sodium silicate as Hematite depressant with ATRAC as Apatite collector• Effect of ASAM as Apatite collector with Sodium silicate as Hematite depressant• Effect of ATRAC (BEROL) as Apatite collector with Sodium silicate as Hematite depressant• Effect of ASAM & ATRAC mixture as Apatite collector with Sodium silicate as Hematite depressant• Effect of Kcarbonate as pH-modifier• Final test to Optimize pH, Collector, DepressantAt this research we have found the optimum circumstance of the flotation of Chador-Malu iron ore in order to decreasing phosphors of iron oxide and floating of Apatite to make pure Hematite.To reach the optimum conditions, some tests were done with different amounts of pH, collector and depressant. The results are as follows:"

Jan 1, 2003

By G. Onal, E. Gock, H. Dincer

"During the conventional chromite dissolution process; chromite ore concentrates were ground to at least <90 µm using the ball mill and after adding Na2CO3 and leaning material (instead of CaCO3 also residues from the leaching process) at a ratio of e.g. 1:0.75:1.2, depending on the specific formulation, follows the digestion e.g. in a rotary kiln, heated in countercurrent. The reaction time is 3 to 8 h. The calcine is comminuted and leached with water or a thin chromate solution. Depending on the type of ore used, the yield is 75-85 %. The disadvantage of the above-described process is that it is impossible, using current technology, to achieve a complete digestion of the chromite ores and that the chromium-containing residues have to be disposed of as special waste, involving a large financial effort.The subject of this study was the investigation of the effect of vibratory milling on chromite dissolution. The impact stress in the vibratory mill causes the mechanical activation of chromite, which is characterised by lattice defects. The degree of mechanical activation can be quantified by measuring the relative X-ray diffraction intensities at the parent lattice planes of chromite. Each relative X-ray diffraction ratio correlates with a certain degree of digestion. As opposed to vibratory milling, a complete digestion of chromite using a ball mill is impossible, even at extremely long grinding times.In this investigation a chromite concentrate from Pulpinar/Kayseri with content of 44 % Cr2O3 and the Eccentric Vibratory Mill was used. In order to verify the effect of the vibrating grinding on chromite dissolution, reaction kinetic investigations on digestion and leaching were carried out."

Jan 1, 2003

By Chris A. Fleming

"Interest in the recovery of cyanide from gold and silver plant tailings has heightened in recent years. This interest has been spurred by several factors:Increasingly stringent regulations throughout the gold producing world, governing discharge limits for free and total cyanide to tailings ponds and the environment.The increasing cost of active chemical treatment versus passive (natural degradation) treatment of tailing, to bring them in line with environmental regulations.The worldwide trend to processing of more complex gold ore bodies, which is usually accompanied by higher levels of cyanide consumptions and greater concentrations of cyanide (particularly the copper cyanide complex) in tailings.The growing negative perception of the general public for the gold mining industry, due to several highly publicized cyanide spills in recent years (breaches of tailings dams, accidents involving trucks carrying cyanide to gold plants, etc.).The ability to recover cyanide from gold plant tailings has been known almost as long as the cyanidation process has been practiced, but there has been little incentive to process tailings in this way in the past. With the development of technologies that make it possible to recover and recycle free or complexed cyanide directly from gold plant slurry tailings, which indicates, on paper at least, the potential for significant cost savings compared to cyanide destruction, coupled with the introduction of legislation to seriously limit the discharge of cyanide to the environment in most gold-producing regions of the world, many companies are evaluating the cyanide-recovery alternative."

Jan 1, 2003

By Zoran M. Stevic, Mirjana M. Rajcic-Vujasinovic, Zvonimir D. Stankovic

"Huge electrochemical investigations have been performed on Technical faculty in Bor (Serbia) which main goal was the clarification of the copper sulfide minerals behaviour in hydrometallurgic and flotation processes. Modeling of these processes was a part of the effort for better understanding of the reaction mechanisms.The consideration of electrical analog circuit and mathematical model of processes at interfaces copper sulfide/electrolyte (CuS/(CuSO4+H2SO4), Cu2S/H2SO4 and CuFeS2/H2SO4), based on studies of the overvoltage – time transients, will be presented. The transients were obtained using single pulse galvanostatic method and electrochemical cell with standard three electrode assembly. In that goal it was developed an original system for computer measurements that enables the application of several methods for electrochemical investigations (galvanostatic, potentiostatic, cyclic voltammetry, electrochemical impedance spectrometry etc). The system was tested and adjusted using commercial electrochemical equipment made by AMEL, Milano.In the first stage of consideration the different equivalent electrical circuits have been tested by computer programme OrCAD 9.2 in order to identify the circuit with responses equivalent in shape to experimentally obtained ones. In that way it was established a configuration of an analog electrical circuit for investigated electrochemical system. That phase enabled only very rough determination of values of circuit components and their relative ratio.In the second stage the method for determination of all elements of electrical analog circuit is described. It is based on mathematical consideration of a given circuit on one hand, and valves of the overvoltages at selected times, obtained from charging and discharging parts of galvanostatic transients, on the other."

Jan 1, 2003

By Mary Stewart, Jim G. Petrie, Geoff Brent

"Life Cycle Assessment (LCA) is gaining increasing acceptance as a decision-support tool by which to evaluate the environmental performance of a product, process or service. This is evidenced by its inclusion in international policy documents (for example in the European Union’s Integrated Product Policy) and in environmental management standards (the ISO 14 040 series of environmental management codes relate to LCA). In response to this, the minerals industry has conducted a number of commodity-specific LCAs. These include studies for global production of a number of commodities including copper, nickel, aluminium and steel. In addition, a number of minerals companies profess to use LCA as part of their suite of project and technology assessment tools. Often, this collected use represents more a situation of “we do this because we’re told it’s good for business” rather than from any demonstrable evidence of this fact. This has led to a situation of much confusion and disillusionment within the industry, exacerbated by the obvious current limitations of LCA to accurately reflect the environmental performance of minerals and metals.Our point of departure here is that LCA, conforming as it does to the tenets of environmental systems analysis, is a valuable starting point, and that there is merit in exploring to what extent the methodology can be enhanced to better reflect the environmental performance of minerals and metals. Specifically, we explore here the further development of LCA to address the following:• Land Use issues• Consumption of Abiotic Resources including metallic and non-metallic minerals, water and soil)• Human and Eco-toxicity issues relating to mobility and bio-availability of metals• Salinityand address these through selected experimental and simulation case studies relating to energy- and base minerals production. Advances resulting from the United Nations Environment Programme/Society for Environmental Toxicology and Chemistry Life Cycle Initiative are presented in that they directly affect the application of LCA to mining, minerals and metals. Comments are offered on how best the mining and minerals industry might interface with future developments resulting from this Initiative in order that the Initiative can deliver outcomes which render LCA a useful tool for decision making in mining and minerals processing."

Jan 1, 2003

By Xie Jiyuan, Hu Yuehua, Yang Songrong, Zhu Zhansheng, Qiu Guanzhou

"By the end of 2000, the first bio-oxidation plant in China that designed by ENFI come successfully into commercial operation in Yantai Gold Smeltery. Its capacity is 50t/d of refractory gold ore concentrate. After the extension, the capacity of bio-oxidation plant reached 80t/d of refractory gold ore concentrate at end of 2001.The refractory gold ore concentrate treated is from different gold mines. After proportionate feeding, the feed typically consists of Au (52.7g/t), S (24.42%), As (3.58%).The bacterial culture used in the bio-oxidation circuit is taken from a mine in south of China, and has been grown over 20 years on a variety of sulfide concentrates in a laboratory of mineral processing, and has shown to be adaptive to growth in a high concentrations of arsenic. It is a mixture of mesophilic microorganisms. The nutrients used in the bio-oxidation process are (NH4)2SO4, KH2PO4, KOH.Before feeding to bio-oxidation circuit, the concentrate would be milled to minus 43µm. The biooxidation product is fed to solid/liquid separation system that consists of a thickener and two press filters, solid from the system is fed to CCD circuit, liquid from the system is fed to neutralization area. The neutralized product is fed to another solid/liquid separation system, and the solid from the system is disposed of on a wasted quarry pit, the liquid from the system is returned to bio-oxidation circuit for reusing."

Jan 1, 2003

By Chen Shuwen, Yao Zhihua

In the process of thickening dewatering_the motion state of two- phase flow in a thickener has a very great influence on thickening efficiency. The investigation was made using copper mill tailings. In this investigation the authors explored the formation conditions and motion range of density current in the thickening process by model experiments, and analyzed the influence of density current on thickening efficiency. The results have shown that the formation of density current has relations with the structure parameters of a thickener and thickening process. The density current and its forming location affect thickener’s working efficiency. The author measured the motion state of two- phase flow in a 53-m dial. thickener for copper mill tailings under its operation conditions and analyzed the density distribution and motion state of two-phase flow in the thickener. The results obtained by the industry tests have shown that the motion state of two- phase flow in the thickener can be greatly improved by modification of its structure, achieving a great improvement in its thickening efficiency. It is concluded that, a thickener’s working efficiency depends on the formation and motion range of density current in it, which is of great importance to designing and establishment of thickener’s working parameters.

Jan 1, 2003

By Carin Laubscher, Francis W. Petersen, Jaap P. Smit

"Waste streams, such as acid mine drainage, are often characterised by low pH values and high concentrations of heavy metals, dissolved solids, calcium and sulphates. Although lime remediation effectively removes most of the heavy metals as hydroxides, it is less effective at lowering levels of sulphates. Various methods of removing sulphates from effluents exist, such as precipitation with lime, precipitation with barium salts, co-precipitation with calcium carbonate, reverse osmosis, and ion exchange. Mintek developed a chemical precipitation (SAVMIN) process to treat acid mine drainage, which entails the addition of lime to precipitate the metal hydroxides, and the subsequent formation (precipitation) of calcium sulphoaluminate or ettringite. The key to the viability of the new technology lies in the correct use, regeneration and recycling of Al(OH)3 used to precipitate the ettringite. The water produced by this process is suitable for disposal to watercourses or for agricultural, domestic or industrial consumption. No brines are produced as the salts are converted to solid hydroxides, gypsum and calcium carbonate.The SAVMIN process has been tested successfully during several laboratory scale operations, and during two pilot plant operations at Stilfontein Goldmine for Anglogold and Navigation Plant, Witbank for Anglocoal. During the pilot plant campaign at Navigation Plant, metal and mineral precipitation was achieved with lime addition. The sulphate concentration in the water was reduced from 2136 mg/L to an average value of 102 mg/L and the calcium concentration was reduced from 727 mg/L to an average value of 70mg/L.The SAVMIN process generates a number of different waste streams including metal hydroxide sludge from neutralisation, gypsum sludge from the gypsum crystallisation steps, and calcite sludge from carbonation. The metal hydroxide sludge is composed of Mg, Ca, Mn and Fe hydroxide, and could be disposed of on a slimes dam. Gypsum sludge was greater than 99% CaSO4.2H2O. This gypsum could be used for dump or road capping, underground backfilling, production of wallboard and cement. The calcite sludge is pure CaCO3, which is recycled back to the neutralisation stage."

Jan 1, 2003

By G. X. Du

Improving reaction effectiveness of asbestos tailings and acid is main means to increase the productivity of magnesium hydroxide and amorphous silica and to reduce production costs. In this paper, the process optimization of acid-leaching reaction process of asbestos tailings is reported. Through the orthogonal experiments of four influence factors, such as acid consumption, reaction temperature, reaction time and initial acid concentration in the leaching reaction. The experiment results indicated that the optimal process parameters were as follows: reaction temperature was 95?, reaction time was 1.5h, acid consumption was 218.9g hydrochloric acid(37%) per 100g asbestos tailings and initial acid concentration was about 25%. The influence significance sequence of the four factors was as follows: reaction temperature > reaction time > mass concentration of hydrochloric acid > hydrochloric acid consumption. Under the optimum process conditions, the leaching rate of MgO was 97.3%, total iron 98.15% and Al2O3 57.9%.

Jan 1, 2014

By J. Tian

"BHP Billiton carried out a pre-feasibility study on the LanPing zinc deposit to evaluate the possibility to jointly develop the zinc deposit into a large-scale zinc project with their Chinese partner. The unique characteristics of the complex LanPing zinc orebody and ore are 1) smithsonite (ZnCO3) as one of major zinc bearing mineral besides sphalerite, 2) varying and irregular oxidation degree of zinc (0 ~ +90%) in the different zone and depth of the deposit, and 3) varying host gangue from limestone/calcite dominant to quartz dominant, which requires a robust and flexible flotation process to recovery zinc from both sulphide and oxide efficiently.The conventional mineral processing flowsheets have been tested on the LanPing samples taken from the various orebodies by various parties during the past 20 years that includes a sequential flotation flowsheet that was tested in a demonstration plant using the mixed ore. The results of the demonstration plant runs show that the conventional oxide flotation using Na2S and amine collectors could achieve 50 ~ 75% of oxide zinc recovery at very high sulphidiser consumption for the mixed ore but the highly oxidised ore did not satisfactorily respond to the flowsheet in terms of performance consistency and efficiency of oxide zinc recovery, which is very crucial to the overall economics of the project."

Jan 1, 2003

By Kauko T. Ingerttilä, Jouko O. Kallioinen, Jaakko O. Leppinen, Alexander V. Lashkul, Vladimir E. Nenno

"Separation in Froth (SIF) is a process for the separation of mineral particles during their descent downwards through a moving froth layer, generated on the surface of water or some other liquid media by means of a bubble generator and frother. Due to the special operation principles of SIF it is possible to separate mineral particles that are about 10 times coarser than the optimal particle size for conventional flotation. In this paper the performance of the SIF technique is presented in the separation of apatite, calcite and silicate minerals from various industrial sources, based on tests with laboratory and pilot plant-scale SIF machines. Basic laboratory test results of the flotation of pure diamonds are also presented.It was shown that calcite, apatite and diamonds with particle size up to about 3 mm can be successfully floated with SIF at high recovery and grade, provided that the degree of liberation is sufficiently high. Coarse calcite (+0.25-2.8 mm) was concentrated with reverse SIF in one flotation step at 87% recovery with better than 99% grade. Apatite particles coarser than 0.2 mm are not well floated in the conventional flotation circuit leading to high P2O5 content in the coarse size fractions of flotation tailings. On the contrary, SIF is capable of recovering such coarse particles at high recovery. However, P2O5 content of the SIF tailings starts to increase at about 0.7 mm due to insufficient liberation of apatite. At higher particle size the lack of hydrophobicity of apatite particles is also likely to lower the recovery.The pilot plant testwork showed that SIF can be successfully used at operating plants not only for preliminary upgrading of the feed of conventional flotation, but also for producing final grade calcite concentrate (>99.5%) from the screen overflow or from the cyclone underflow in a particle size range up to 1 mm. It was particularly promising that the separation took place in one SIF flotation step, instead of several stages of the conventional flotation circuit, with over 90% calcite recovery. The specific capacity determined with the 1 m2 pilot plant unit was approximately 30 t/m2h. Simultaneously the consumption of chemicals was significantly lower than for conventional flotation."

Jan 1, 2003

By Ralph J. Holmes, Victor Sharp, Steven J. Spencer, CSIRO Minerals, Kevin J. Davey, Jonathan J. Campbell, Peter L. Phillips

"Improved measurement tools for monitoring and control of AG/SAG mill performance have a high level of interest in industry. Historically, acoustic emission monitoring has been widely used on SAG/AG/ball mills and hydrocyclones to provide new information on the conditions inside these devices affecting their performance. The current work was focused on a new technique using surface vibration monitoring of a number of pilot-scale and production-scale AG/SAG mills to yield insights into the events occurring in the mills. The development of relationships between signal analysis outputs and mill operating conditions can be used for soft-sensor measurement of mill process variables. The technique used an array of accelerometers mounted on the mill lifter bolts linked to a fast data acquisition system which monitored the surface waves generated during operation. Details of the system are presented. Mill operating variables were adjusted systematically to provide a wide range of operating conditions for surface vibration signal collection. The experimental approach is discussed.The signals acquired during the experiments were analysed using a range of techniques. The results show that strong relationships exist between measured vibration power (both total power and within certain frequency bands) and mill load level/power and mill speed. A new method for extraction of power spectral density and band power information on features of interest in a mill rotation cycle is also presented."

Jan 1, 2003

By Malcolm Mudge

"One of the oldest mining areas in the World exist in Africa and the Middle East. This area is being exploited by foreign and local mining entities. Several large plants, both foreign and local as well as small operators, conduct their mining business on a scale which would be could be prohibited in any other part of the world. Relatively recent European disaster with tailing disposal and breakout has highlighted the problem.More important to the author is that the presence of foreign entities in zones which have not remedied the situation but has heightened the concern due to those entities using similar outrageous methods in treatment of waste. The abject misuse of technology cannot be permitted to continue and the lack of any metallurgical knowledge in the treatment of gold ores is considered deplorable for the majority of third world countries.The destruction of cyanide is simple and straightforward and requires no special skills. In South America, we developed a system that is modular, compact and can be operated in batch mode to cater for several clients, as required. Larger installations would require a separate module, as treatmentwould be on a continuous basis."

Jan 1, 2003

By Atsushi Shibayama, Toyohisa Fujita, Luo Lin, Toshio Miyazaki

A novel process is developed in this study for separation of tungsten and vanadium from a leach solution of tungsten alloy scraps. Specifically, a magnesium salt combined ammonium solution is employed to precipitate vanadium and impurities in the purification of the leach solution. This separates vanadium from tungsten by rejecting tungsten in aqueous solution. Finally, tungsten is recovered as the form of ammonium para-tungstate (APT). Vanadium is recovered as the form of ammonium meta-vanadate(AMV).

Jan 1, 2003

By Susanna G. de Jager, Francis W. Petersen

"To enable the prediction of reagents suitable for fine coal flotation, it is necessary to develop a methodology applicable to different South African coal types. Statistical confirmation of the applicability of this methodology is important to avoid recommendation of reagents on a trial and error basis.The study included 5 coal samples from different collieries and included Highveld seam 3 and 4 coal (as one sample), Waterberg coal (zone 10 -11), Highveld seam 5 upper coal and Witbank seam 2 and seam 4 coal. Seam 3 and 4 (mixture) coal, Waterberg and the seam 5 upper coal were all found to be vitrinite rich coals. The coal characterisation study included petrographic analysis, proximate analysis, float-sink analysis, oxygen-containing functional groups, surface extraction, flotation release analysis and contact angle measurements. Flotation tests were used to validate expectations from the characterisation of the coal samples.RESULTSThe flotation data indicated that all of the coal samples were amendable to froth flotation. The best results were obtained with the Witbank seam 2 coal and the poorest flotation with Syferfontein seam 5 coal. The flotation tests showed that the best reagents to float all of the coal samples studied were iso-decanol and dodecene. These reagents produced flotation products that were near to the release curve, which are the optimum flotation results (obtained when using iso-paraffin as collector). Dodecene resulted in low ash products and iso-decanol in high yield products."

Jan 1, 2003

By Vladimir I. Ryaboy, Konstantin M. Asonchik

"At flotation of sulfide-barite ores of one of deposits sulfide and barite concentrates are obtained. In sulfide cycle potassium xantogenate as a collector in consumption of 200 g/ton, methylisobutylcarbinol (MIBC) as a foaming agent in consumption of 30 g/ton and also liquid glass are used. In barite cycle tall oil as fatty acid collector in consumption up to 400 g/ton is used.Sulfide concentrate represents mainly gold- and silver-containing pyrite. The contents of gold makes not less than 10 g per ton, silver - not less than 278 g/t. Barite concentrate contains up to 86% of barite.Factory is working in water recirculation conditions. Owing to that in barite cycle fatty acid collector is used, technological water from tailing repository contains fatty acids soap up to 25 mg/l. Before submission into sulfide cycle this water is conditioned with active carbon to delete the main part of fatty acid collector. The active carbon consumption makes 0,4-0,5 kg per 1m3 of water or 1,5-2 kg per ton of ore. The above mentioned consumption of active carbon improves reducing of contents of fatty acid collector from the initial concentration of 25-30 mg/l to 4 mg/l. At concentration 4 mg/l fatty acid collector does not render negative influence on flotation index in sulfide cycle. At the absence of active carbon pollution of sulfide concentrate and its irrevocable lost are observed."

Jan 1, 2003

By Kang N. Zhong, Hui H. Luo, Yunan Phosphate Chemical Co., Yi H. Wei, Yao J. Li, Yu L. Wang

"The three kinds of phosphate ores (igneous, metasedimentary and sedimentary) found in China have great differences in flotation flowsheets and reagents suite because of their crystal structure and mineral composition. The igneous and metasedimentary apatites have good floatability with fatty acid as collector and waterglass, sodium hydroxide or sodium carbonate as conditioners. The sedimentary phosphate is very difficult to beneficiate by direct flotation because of their poor floatabilities and relatively high content of MgO and SiO2, even though the dolomite depressants are used sometimes.The differences in floatability of apatites in China are closely related to their differences in specific surface area. The amount of collector to float apatite increases with the specific surface area. Apatite with lower specific surface area showed good floatability at lower collector concentration. Apatite with a higher specific surface area needed a higher concentration of collector. The content of CO3 2- will affect the specific surface area of apatite by distortion of its crystal structure and consequently affect its floatability.Dolomite can be easily rejected from apatite in a weak acidic medium (pH=5), especially in phosphoric acid medium by reverse flotation. Quartz and siliceous gangue in sedimentary apatite can be removed by direct flotation using fatty acid or by reverse flotation using amine. Amine is not practically applied because sedimentary apatite in China is usually very fine and needs fine grinding, which always results in excessive, very fine, stable and non-flowable foam.Based on the floatability of phosphate ore in China, a two-stage flotation process, direct and reverse flotation (D+R), was developed to beneficiate sedimentary ore. For the Haikou phosphate ore containing 25.11% P2O5, 3.46% MgO and 16.5% SiO2, a concentrate containing 31.84% P2O5, 0.48% MgO and 14.8% SiO2 can be obtained through a continuous D+R test at a recovery of 89%."

Jan 1, 2003

By Yuexin Han, Zehong Wang, Fujia Yu, Wanzhong Yin, Xinchao Wei

Bauxite is the main raw material in alumina and refractory industries. China has plentiful bauxite resources, most of which belong to the diaspore type bauxite with characteristics of high aluminum content, high silicon content and low ratio of alumina and silica (A/S). The resources with A/S 4-7 account for more than 60% of the total resource reserves of bauxite. Therefore improving the A/S through bauxite desilication is the key task of bauxite concentration in China. Normally the grinding fineness of 80-90% - 0.074mm is required in the bauxite flotation process. Thus fine grinding of bauxite ores is necessary, which leads to the high energy consumption. In the meanwhile, bauxite ores are easy to produce slime during grinding processes. The large amount of slime produced in fine grinding greatly worsens the process environment of bauxite flotation, affects the separation performance and results in the loss of metal. Also, fine grinding makes the flotation concentrate difficult to dewater, while the water content in the flotation concentrate must be removed by distillation in the subsequent alumina dissolution process, causing the increase of energy consumption and cost in the production of alumina. In this study, the selective grinding behaviors were examined with Henan Bauxite as feed. Separation of alumina and silica at a coarser grinding fineness was achieved and new route was explored to enhance the desilication in bauxite concentration to improve the A/S of bauxite concentrate.

Jan 1, 2003