Search Documents

By Justin C. I. Baulch

In October 2004 Placer Dome entered into an exploration farm-in agreement with Nautilus Minerals, to explore for Submarine Massive Sulphide (SMS) deposits on Nautilus? PNG exploration tenements. Placer/Nautilus currently holds approximately 15,000 km2 of tenements in PNG waters, either granted or under application, covering all reported seafloor hydrothermal vent occurrences.

Jan 1, 2005

By Philomene Verlaan

This study examines the possible relationships between compositional variability in non-hydrothermal manganese nodules and large-scale environmental parameters. In the central SW Pacific (145-180° W and 20-O° S) the level of primary productivity, the rates and proportions of carbonate, silica and organic matter supply to the sediments, and the position of the seafloor relative to the Calcium Carbonate Compensation Depth (CCD) appear to directly influence nodule composition. Four zones of nodule composition are apparent. These zones correlate fairly well with the level of primary productivity in surface waters, as estimated by satellite-based measurement of chlorophyll content. The observed correlations between surface productivity and nodule composition are consistent with the contention that the dominant source of several transition metals in these deposits (i.e , Mn, Ni, Cu. and Zn) is provided by removal of fine-grained particulate matter from the water column by biological means. Subsequent decay of organic matter in sediments augments the content of these metals in the nodules through oxic and sub-oxic diagenesis. The opposite behavior of Fe and Co content may in part result from mineralogical and dilution effects.

Jan 1, 2000

By Nobuyuki Okamoto, Bhaskar Rao

For a period of twenty years - from 1985 to 2005 - the Japan Oil, Gas and Metals National Corporation (JOGMEC) and Pacific Islands Applied Geoscience Commission (SOPAC) have jointly conducted surveys of deep-sea mineral resources in the EEZs of SOPAC’s twelve member countries. The overall Programme has obtained excellent results and has identified numerous sites with potential marine mineral resources of manganese nodules, cobalt-rich manganese crusts, and polymetalic massive sulphides. The survey cruises have identified numerous sites with potential marine mineral resources such as: manganese nodules in the Cook Islands; cobaltrich manganese crusts in the Marshall Islands, FSM, and Kiribati; and polymetalic massive sulphides in Fiji. Based on collected samples and acoustic data, inferred resources for manganese nodule, cobalt-rich manganese crusts, and polymetalic massive sulphides, have all been estimated to be about- 200 million tons in the central Cook waters- 200 million tons in the three seamount selected Marshall waters- and 500 thousands tons around the triple junction of the North Fiji Basin.

Oct 15, 2007

By B. S. Ingole, S. Jai Sankar, A. B. Valsangkar, R. Sharma, B. Nagender Nath, N. H. Khadge, P. A. Loka Bharathi

After the simulated ‘mining’ experiment (INDEX) in the Central Indian Ocean (in 1997); the restoration of benthic environment was monitored for 4 years (2001-2005) at 5 locations in and around the test site and at 3 reference stations (20-80 km) from the test site. A comparison of long-term monitoring data with the pre-mining and post mining observations has shown that: • The concentration of silt fraction which was the highest (50-60%) at most locations during ‘pre-mining’ and ‘post-mining’ phases, had reduced (40-50%) during monitoring phases. • There was a corresponding increase in clay concentration (50-60%) during the monitoring phase, implying change in the size of sediment particles settling on the seabed, a trend that was also observed at the reference locations. • The initial increase in water content and decrease in shear strength after the experiment, which appeared to be returning to normal in monitoring-1 (2001), was reversed during subsequent monitoring phases (2002-2005), indicating changes in benthic environmental conditions. • Sediment organic matter and pore-water chemical data have not only indicated partial restoration of geochemical properties after the experiment, but also cyclic changes during the monitoring period.

Oct 15, 2007

By Gregory J. Kurras

In 1995 the Marine Minerals Technology Center (MMTC) of the University of Hawaii conducted a sidescan sonar survey and sampling expedition of the submarine geology and hydrothermal systems surrounding the active volcano White Island. The island is located in the Bay of Plenty, within the geothermally active Taupo Volcanic Zone off-shore of the North Island of New Zealand, and is the site of numerous shallow-water hydrothermal systems. The survey system, an EdgeTech DF1000 sonar, was a dual frequency 100 kHz & 500 kHz sonar capable of imaging the seafloor at better than 1 m resolution and possibly detecting gas bubbles within the water column. Sidescan imagery clearly shows sand channels, debris slumps, submarine landslides, and volcanic ridges all around the island to roughly 800 meters offshore. However, analyses of the both raw and processed acoustic data indicate that the sonar was not able to image any of the shallow-water hydrothermal gas seeps known to exist around the island. Vents were located using a commercial fish finder and knowledge from local tour guides and divers. Eleven gas samples from three different sites were collected by divers for analysis of chemical and isotopic composition. Rock samples were collected from thirteen underwater outcrops for correlation with existing data on subarial island flows sampled by previous investigators. Thin sections and XRF analysis were done for each rock to determine mineral assemblages along with major and trace elements, which were used to tie submarine samples to specific subarial stratigraphic layers.

Jan 1, 2011

By Alexey Musatov, Georgy Cherkashov

Based on geochronological data it was confirmed that hydrothermal discharge has an episodic character: active and inactive periods of the seafloor massive sulfides (SMS) formation alternate (Cherkashov et al., 2017). There is an assumption of correlation of the periods of magmatic and hydrothermal activity with the stages of glaciation (Lund et al., 2016). During the cold periods, the level of the ocean was reduced from 70 to 150 m depending on the glaciation scale (Spratt, Lisiecki, 2016). As a result, the hydrospheric pressure on the upper mantle decreased and could provide increased magmatic and hydrothermal activity (Lund, Asimow, 2011). This assumption is confirmed by the correlation of warming and cooling stages with increasing of hydrothermal input to the bottom sediment near hydrothermal fields. According to data (Lund et al., 2014, 2016; Middleton et al., 2015) the peaks of hydrothermal activity, expressed in the layers of metalliferous sediments at the East Pacific Rise and the Mid-Atlantic Ridge, roughly correspond to the last two periods of cooling (20 and 60 ka). To test this hypothesis, we tried to compare the sequence of warm and cold periods in the Pleistocene with the dating of SMS reflecting the periods of hydrothermal activity. Results SMS samples were obtained from 12 sites within the Russian Exploration Area at the MAR segment 12-20°N. The results of dating 198 samples by the 230Th/U method demonstrated the absence of correlation between hydrothermal activity periods in different hydrothermal fields (Cherkashov et al., 2017). It was proposed that each field has its own evolutions scenario. Considering this point, only the oldest SMS dating for each field which fixed the beginning of hydrothermal activity was selected for comparison with the cold/warming periods.

Jan 1, 2018

By Jai-Woon Moon

Lemkein seamount located in the west of the Kuwajleen Atoll of RMI is a relatively samll, simple-shaped, peaked type seamount with its base at 4,500 m and summit at 1,452 m water depths. Ferromanganese crusts were identified in the water depth range between 2,000 m and 2,500 m, and they were mostly observed on the northern slopes of the seamount. Among various substrate rocks, breccia occurred most commonly with crusts and formed the thickest crust layers. Average thickness of the Lemkein crusts was about 5 cm. Their chemical compositions were similar to other crusts found in the RMI area; Mn=25.82%, Fe=15.29%, Co=0.74%, Ni=0.56%. Lemkein crusts were characterized by their four distinctive internal layers; 1) Massive Layer 1; 2)Porous, Fe-stained or sediment infilled Layer 2; 3) Massive to slightly porous Layer 3; and, 4)Massive, Dense, Phosphotized, CFA veined Layer 4. Layers 1 and 2 were generally similar in composition, but highest Co concentrations were measured in Layer 1 while relatively higher concentrations of Al, Rb, Fe, and Ti were observed in Layer 2. Layer 3 showed higher concentrations of Ca and P than Layers 1 and 2. Based on the Co-chronography, the age of Layer 1 is 0¡?6 Ma (growth rate = 1.50 mm/Ma), Layer 2 is 6¡?15 Ma (1.75 mm/Ma), Layer 3 is 15¡?27Ma (1.76 mm/Ma), and Layer 4 is 27¡?45 Ma (2.06 mm/Ma). These preliminary results indicated that high Co contents in Layer 1 resulted from slow growth rates; Layer 2 was formed under relatively strong influence of high terrestrial input; and, Layer 3 was probably affected by a minor phosphatization event occurring in 15 Ma.

Jan 1, 2000

By R. P. Das

Processing of polymetallic nodules poses several challenges to metallurgists. These include the presence of at least 80 elements in nodule, presence of Ni, Cu, Co in no specific mineral form, presence of almost 30 % seawater in freshly collected nodule, and collection of slime along with the nodule. For almost 40 years, several research groups from all over the world are engaged in developing an appropriate process to extract metals from poly-metallic nodule. These processes have been tested in scales varying from few grams to several hundred kilograms (Das, 2001; Jandova, 2001). All these tests helped in defining various parameters for processing, and simultaneously brought out some of the inherent problems of processing nodules. Based on the information and the experience of all these studies, in recent years, most research groups, involved in developing metallurgical processes for nodule, are focusing their efforts in two or three alternative directions. While attempts are made to overcome some of the major challenges in processing, several new ones crop up. The difficulties are further compounded because no mining system is operating to generate some of the data required for process development. The aim of this presentation is to highlight the research efforts, and to identify areas requiring special attention of a process developer.

Jan 1, 2003

By M. Ravindran

The Government of India started its deep seabed exploration programme during 1982. This programme was started as one of national importance and several national laboratories were involved to realize the development of requisite technologies for deepsea mining and processing. After a concentrated effort on surveying, using its own as well as hired ships, India succeeded by mid 1980s in identifying a prospective site in the Indian Ocean as an exclusive claim for development. India was registered as a Pioneer Investor and became the first country to obtain this status on 17th August 1987. India has been allocated an exclusive mine site of 150,000 km2 in the Central Indian Ocean. Our country also developed considerable expertise in the metallurgical processing for extracting metals from these nodules. The Department of Ocean Development, Government of India, the organization which is designated as the nodal agency responsible for implementing the deep seabed mining programme has drawn up a long term plan which will enable it to fulfill its obligations as a Pioneer Investor. The work toward the design and development of a mining system has been entrusted to the Central Mechanical and Engineering Research Institute, Durgapur. As a part of this programme they have developed a nodule collector and a riser system which have been tested in very shallow waters only. Since this technology development for deep sea mining applications is highly time consuming and very expensive, this programme is also being used to develop components for intermediate applications. In view of the long timeframe required for perfecting a deepsea nodule mining technology, the Government of India is also keen on developing shallow water mining systems for utilizing the placer deposits. One of the richest heavy mineral deposits in the Indian Exclusive Economic Zone is available on the west coast of South India in the state of Kerala. The coastal stretch between Kanyakumari, on the southern tip of India, and Alleppey along the west coast at a distance from the tip of approximately 210 km, there is a good multimineral reserve. The initial survey indicates that the estimated reserves in the surveyed areas are approximately as follows: Ilmenite 1.4 million tonnes Rutile 0.14 million tomes Zircon 0.13 million tomes Sillimanite 0.53 million tonnes

Jan 1, 1994

By Akira Usui

The small-scale observations, mapping, sampling, and in-situ experiments have been carried out since 2009 using JAMSTEC ROVs at some model seamounts in the Northwestern Pacific seamounts. Laboratory analysis on mineralogy, chemistry, chronology indicated a continuous slow precipitation since the Middle Miocene, at water-depths 1-6 km, and the modern hydrogenetic precipitation even in the oxygen minimum zones. Thus the variability in abundance and grade of the deposits on regional, small and microscopic scales are determined by geological, geochemical, and hydrological conditions, resulting in the stacked piles of tiny precipitates from the seawaters.

Jan 1, 2018

By V. K. Banakar

The occurrence of hydrogenous ferromanganese encrustations (Fe-Mn crusts) on the Cretaceous age Afanasiy-Nikitin Seamounts (ANS) in the eastern Equatorial Indian Ocean (EEIO) was first reported by Banakar et al. (1997, Marine Geology). The major element composition of the samples from the upper flank of the ANS (~1650 m water depth) indicated enrichment of Co up to 0.9 % (Parthiban and Banakar, 1999, Indian Mineralogist). Subsequently a project supported by the Department of Ocean Development to explore the ANS for Co-enriched Fe-Mn crusts was launched in 2002 by the National Institute of Oceanography. Sampling at regular depth intervals along two transects on the slopes of the northern elevated region of the ANS was carried out. The Fe-Mn oxide deposition is evident on almost all types of substrates viz., basalts, conglomerate limestone, fossil corals etc., and the thickness of the oxide layer varies from a patina to 7 cm. The Fe-Mn crust growth is evident only above a water depth of 3200 m, below which semi-lithified carbonate ooze is dominant. The ANS Fe-Mn crusts from all the water depths exhibit Mn/Fe < 1.5 suggesting pure hydrogenetic accumulation of metal-hydroxides. Bulk sample Ce-contents for a few selected depth-representative samples are remarkably high, up to 3700 ppm with an average of ~2500 ppm. The positive Ce-anomaly decreases from ~8 at 1600 m depth to ~1.6 at 3200 m depth, which is in contrast to the modern dissolved oxygen depth-profile in the region. This observation suggests that major time-period of the Fe-Mn crust accretion history is dominated by ambient waters with lower-oxygen at deeper depths than at the intermediate depths. This in turn probably suggests a major reorganization in the deep-intermediate hydrography of the region in the past.

Jan 1, 2005

By Dennis Sánchez Mora, John Jamieson

INTRODUCTION Work by Humphris et al., (2002); Ondréas et al., (2009); Barreyre et al., (2012); and Escartín et al., (2015) has identified active and inactive hydrothermal sites along the Lucky Strike segment. The sites that contain the largest accumulation of known sulfides are located between the north and the southern zones (Figure 1), a vent site area that is referred to as the Main Lucky Strike hydrothermal field (Escartín et al., 2015). Hydrothermal fluid outflow has been linked to a shallow fault network (Barreyre et al., 2012). However, specific constraints on fault geometries have not been determined. Other off-axis sites at Lucky Strike, such as Capelinhos (high temperature vent), and Grunnus (inactive?), as well as a low temperature vent field (on-axis), Ewan, have been described by (Escartín et al., 2015). Given the spatial relationship between the Main Lucky Strike hydrothermal field (MLSHF), and the intersection of northern rift faults with the southern rift faults, a structural analysis of this area can provide insight into the fault controls on fluid flow that leads to hydrothermal venting and sulfide precipitation. METHODOLOGY Structural data (dip direction and dip) was determined using Leapfrog Geo 4.0 software. Bathymetric data was obtained from Escartín et al., (2015) and references therein. The bathymetry was imported into Leapfrog Geo (in UTM format) and, using the structural modelling tool, individual measurements with dip direction and dip data were collected with a focus on the northern volcanic rift and the southern central volcano (Figure 2a). All measurements were taken from what the authors consider as normal faults, and to aid the determination of individual measurements a “face dip” map was constructed, where the bathymetry is colored by slope angle (Figure 2b). All measurements are simultaneously plotted on a stereonet generated by the Leapfrog Geo Software. Data were divided into northern and southern, and western and eastern zones to determine the relationship between hydrothermal venting and the structural geometries at Lucky Strike (Figure 2c). Slip measurements for individual faults were determined along the dip of the fault with a measuring tool. Net slip, heave (horizontal displacement), and throw (vertical displacement) was calculated for each of the zones.

Jan 1, 2018

By Samantha Smith

Nautilus Minerals (Nautilus) is following the lead of the petroleum industry as it strives to tap vast offshore resources. Planning is well underway for the Solwara 1 Project in the Bismarck Sea, Papua New Guinea (PNG) to recover high-grade seafloor massive sulphide deposits in 1600 m water depth. The deposit contains an average copper grade >10 times higher than a typical land-based porphyry copper mine. The high grades combined with a relatively small amount of overburden ensure the Solwara 1 Project will have a significantly smaller physical footprint than its land-based counterparts. Offshore minerals production also has the advantage of minimal social disturbance. Nautilus is dedicated to setting a high environmental and social responsibility standard. Nautilus recognises the importance of transparent and inclusive stakeholder engagement and has taken a proactive approach to involve as many key stakeholders as possible. One of the first steps in the permitting process in PNG is the preparation of the Environmental Inception Report, which describes the project, its envisaged impacts and the proposed studies for the Environmental Impact Assessment (EIA). Local (PNG-based) and international environmental scientists, anthropologists, NGOs and other experts were involved in the definition of studies conducted for the Solwara 1 EIA and a team of world-leading experts was involved with carrying out the studies, culminating in the preparation of the Environmental Impact Statement (EIS). To ensure transparency, collaborating researchers are free to publish their findings. Following its submission, the EIS was made available for public review and public hearings were held at several locations. The EIS has also undergone a rigorous independent review by PNG government-engaged consultants. Outside the permitting process, Nautilus works alongside government officials to carry out ongoing community consultations. Information dissemination and feedback acquisition has also occurred through the Nautilus website and attendance at a number of international conferences, workshops, and meetings. This paper will outline the leading edge approach Nautilus has taken in completing the environmental impact statement for the world?s first deep seafloor copper-gold mine. In addition, this paper will review the permitting process and the government and stakeholder engagement undertaken as part of Nautilus? desire to ?do it right? in this exciting new industry.

Jan 1, 2010

By Kris van Nijen

IHC Merwede, a Dutch supplier of ships and equipment for dredging and mining activities, and DEME, a Belgian dredging and environmental services group, will enter into a joint venture for deep-sea mining activities. Under their cooperative agreement, IHC Merwede will be responsible for the development and construction of technical solutions, while DEME will be responsible for operations. Together the companies will offer a unique pioneering total solution. The joint venture will be known as OceanflORE.

Jan 1, 2011

By T. Yamazaki, T. Goto, R. Arai, N. Nakatani

The importance of cobalt-rich manganese crusts on the Pacific seamounts for possible future rare metal sources has been recognized these 30 years. The thin layer-type coverage and the micro-topographic undulation of basement affect not only the excavation efficiency but also the economy of mining venture. Because of these distribution characteristics, no economic feasibility has been recognized through the past economic analyses. On the basis of a recent geological study about seamount rocks, a possibility of by-product substrate recovery for phosphorous supply with cobalt-rich manganese crust mining has been highlighted. In the mining model, the substrate rocks are utilized as phosphates for agricultural and chemical usages. Under some preliminary technical and economic assumptions, the possibility of cobalt-rich manganese crust mining venture is examined. The results show a better economy of the venture including the substrate rock usage for phosphorous supply. Introduction Cobalt-rich Manganese Crusts and the Economic Feasibility Cobalt-rich manganese crusts on the Pacific seamounts received attention as potential sources for strategic metals such as Co, Ni, Cu, and Mn, due to their vast distribution and higher cobalt concentration than manganese nodules (Cronan, 1980; Halbach, 1982; Manheim, 1986). In the earlier stage, the geological distribution characteristics were reported (Cronan, 1984; Clark et al., 1984; Misawa et al., 1987; Pichocki and Hoffert, 1987) and a systematic feasibility of the mining was studied (Hawaii DPED, 1987).

Jan 1, 2018

By Henk van Muijen

From an interesting and intriguing scientific research topic, deep sea mining has altered into an interesting mining prospect over the last years. Ten years ago most of the focus was on geological investigations, searching for typical deep sea deposits and getting answers on where we can find them and how these deposits were formed. At this moment we know much more about the interesting deposit possibilities and with our quest for minerals, metals and other materials to feed global economic growth, answers as to the technical and economic feasibility to mine these deposits are sought. This is not a new phenomenon as we already witnessed such question late 1970?s and early 1980?s. Most of the focus was on mining manganese nodules and brines in the Red Sea driven by the report of the Club of Rome that predicted shortages in near future at that time. Development went different, but later in the 1990?s a rival of interest could be noticed for mining deep sea deposits.

Jan 1, 2010

By Georgy Cherkashov

Shallow-water formation of marine ferromanganese nodules as well as their deep-water analogues is found throughout the global ocean. The Baltic Sea is a key province for the shallow-water type of marine minerals. The following main distribution areas of Fe-Mn nodules have so far been discovered in the Baltic Sea: the Gulf of Bothnia, the Gulf of Riga, Central Baltic area (Gdansk- Klaipeda) and the Gulf of Finland. The last area (Gulf of Finland/Finnish Bay) is the best studied from all aspects including geological prospecting and environmental assessment.

Sep 14, 2011

By Valcana Stoyanova

Deep-sea mining of polymetallic nodules are expected to produce serious impact on benthic ecosystem due to removal of nodules, sediments and associated fauna by means of collector, and subsequently, by the resettlement of sediment plume which may affect seabed biota outside mining tracks through blanketing, smothering and feeding interruption. The scale and magnitude of the exact impact of commercial operations is not known at present, but its assessment strongly required acquisition of the adequate environmental baseline information. During the past two decades, IOM carried out a total of 20 research cruises in the eastern part of Clarion-Clipperton Zone (CCZ) with purpose to obtain essential data and information on polymetallic nodules and to prepare for future development their deposits. Whilst evaluating the nodule coverage at particular station from both seafloor photographs and box-core recoveries it was ascertain that the ground-truth data plotted against the photo data indicated substantial differences between two methods. Understanding of this phenomenon has not only the methodology meaning related to the efficiency of the using photoprofiling techniques during exploration of nodules, but also it could be of environmental importance because the similarity between natural sediment blanketing occurrence in studied area and expected re-deposition and blanketing of sediments which will be disturbed during mining operations.

Jan 1, 2011

By Grigori Abramov

As we enter into the 21st Century, miners are looking more attentively at new mining technologies allowing decrease environment damage along with operational cost. This technic would allow developing of poor and difficult mineral deposits, including the World Ocean offshore zone. Borehole Mining is an underground/underwater remote method of mining carried out from floating platforms or vessels. Definition of Borehole Mining (BHM), working schematic, main technical data and its advantages are given. The method is currently in use in mining of different type of raw materials, such as: uranium, iron ore, quartz sand, coal, polymetallic ores, phosphate, gold, diamonds, rare earths, amber and more. It is also in use in oil and gas stimulation, salt domes storages building and environmental problems solution. Recently recorded data of Borehole Mining productivity (80-100 t/hour/hole) and a depth of mining (over 1 km) has been achieved in a last couple years. Remoteness of method not only secures complete safety of operations but also allows wide sector of underwater applications. The World leaders in Borehole Mining are Russia and the United States. Based on previous experience the Universal Tool for Seabed Borehole Mining has been developed for wide sector of usage: from exploration and mining - through oil & gas stimulation to souterrain storages construction and lake&apos;s bottom cleaning.

Jan 1, 2000

By Jonguk Kim

Texture and geochemical composition of hydrogenous ferromanganese crust from relatively adjacent three seamounts (OSM2 at 157°35&apos;E, 13°55&apos;N, Lomilik at 161°37&apos;E, 11°42&apos;N and Lemkein at 165°05&apos;E, 9°18&apos;N) near the Marshall Islands in the western Pacific (Figure 1) were investigated in order to elucidate their growth history. These seamounts, located in different latitudes, are along a line that is parallel with the direction of Pacific plate movement. Thick crusts commonly have three or four distinct layers (Figure 2): (1) layer 1, uppermost layer, is black, dense, and has a botryoidal, columnar, or laminated texture; (2) layer 2, overlain by layer 1, is Fe-stained, porous to vuggy and filled with sediment; (3) layer 3, phosphatized layer, is black, massive, dense, and impregnated by CFA, (4) layer 4 shows parallel to undulatory laminated texture and cut by CFA-filled veins. Layer 1 and 2, unphosphatized young layer, are observed in crust samples collected from all seamounts. However, lower part of the crust shows different textures in different seamounts. Both layer 3 and 4 are found in thick crust from OSM2 but layer 4 is absent in crust samples from Lemkein and Lomilik. All the uppermost layers (layer 1) from three seamounts have similar textural and geochemical characteristics. Layer 2 is overlain by layer 1, is porous, partly Fe-stained, and sediment-infilled. In previous studies, layers 1 and 2 have grown in different oceanic environment. Textural and geochemical properties show that layer 1 has grown under relatively higher bottom water activity and lower productive environment than layer 2. Carbonate and detrital materials in layer 1 are not abundant compared to layer 2. Layer 2 can be assumed to have grown under equatorial high productivity zone (EHPZ) while layer 1 has started to grow when the seamount left from the EHPZ.

Jan 1, 2003