Search Documents

By Kyung-Ho Park

The smelting leaching process is known as one of the most favorite methods for the processing of deep-sea manganese nodules because of its smaller environmental impact and easiness of manganese recovery. The sulphuric acid pressure leaching of the matte prepared from deep-sea manganese nodules was studied to dissolve the valuable metals. Almost complete dissolution of Cu, Ni, and Co from matte was achieved under the following conditions: leaching temperature 180°C, time 4 hours, PO2 10 kgs/cm2, acid concentration 2.5% (vol/vol), pulp density 5%, ammonium sulphate 40 g/l. Under these conditions the iron concentration of leach liquor was 0.95 g/l. Optimization of leaching parameters was carried out by statistical design of experiments using 23 full factorial matrix. The linear and interaction co-efficients were evaluated for dissolution of metal values and also for iron concentration in leach liquors.

Jan 1, 2003

By Arturo Carranza Edwards

One hundred ninety nine beach face sand samples from an equal number of beaches from the Mexican Pacific were studied. Based on petrological and chemical analysis some locations have been studied in more detail. Black sands from the following areas are discussed: (1) west Baja California Peninsula, where black sands rich in magnetite and ilmenite have maximum values of 50% iron and 14% titanium in the very fine sand fraction; (2) east Gulf of California, in its northern portion, the black sands show maximum values of 43% iron and 5% titanium in the fraction 2 to 4 0;-(3) the south Mexican Pacific, characterized mainly by medium sands, moderately well sorted, show that the fine sand fractions reach values of 35% iron and 41% titanium. X-ray fluorescence applied on selected samples constituted by feldsarenites and lithic feldsarenties, showed the presence of rare elements in some of the studied samples.

Jan 1, 1994

By Sven Petersen

In April 2010 three REMUS6000 series autonomous underwater vehicles (AUVs) have been used to simultaneously map large areas near the Mid-Atlantic Ridge (3°N) axis in water depths ranging from 1,000m to 4,000m. One vehicle was provided by the Leibniz-Institute for Marine Science, IFM-GEOMAR (Kiel, Germany) the other two were provided by the Waitt Institute for Discovery (La Jolla, USA) and managed by the Woods Hole Oceanographic Institute (USA). The REMUS6000 vehicles, manufactured by Hydroid Inc. (USA), are "cigar-shaped" vehicles (4m long and weighing approx. 900kg) and consist of a tapered forward section, a cylindrical midsection and a tapered tail section. An internal titanium strongback, which extends through much of the vehicle length, provides the structural integrity and acts as a mounting platform for syntactic foam, equipment housings, various sensors and release mechanisms. The AUVs can be used in various payload configurations such as multibeam bathymetry, electronic still camera, or subbottom profiler. For these missions the electronic still camera configurations was installed. An EDGETECH 2200M dual frequency (120/410 kHz) side scan sonar was used to map the seafloor, but other frequencies are readily available for more options in resolution and range. The 120 kHz side scan transmitter was used for most missions in order to map large areas (increased range) and to be able to fly at higher altitudes (between 70m and 90m) above the rough seabed encountered in this area. The maximum slant range was between 600m and 700m on both sides resulting in a swath width of up to 1.2 km. Line spacing ranged from nearly 1,000m in flat areas down to 400m in steep terrain. Side-scan mosaics were generated with a 1m resolution. Selected areas were targeted by the higher resolution 410 kHz transmitter as well as by bottom photographs flying as low as a few meters above the seabed. The vehicles navigated autonomously using a combination of inertial navigation (Kearfott T-24 or T-16 INS) and long baseline acoustic navigation by computing their range to two moored acoustic transponders. Working efficiently in this rough topography at speeds above 3 knots was only possible due to the obstacle avoidance capabilities of these AUVs.

Jan 1, 2011

By H. Oda, L. E. Fong, K. K. McBride, B. P. Weiss, F. J. Baudenbacher, A. Usui

Fine-scale dating is a key parameter in characterizing the growth history of hydrogenetic ferromanganese crusts. We once compared several dating methods, micropaleontological (calcareous nanofossil), radiometric (10/9Be), and paleomagnetic (step-wise measured inclination) methods on single samples, but these independent methods were not consistent with each other (Joshima & Usui, 1999). For example, a 4-cm thick crust was dated as 3Ma by the fossil-paleomagnetic combined method, while it dated older than 5.5 Ma by Be-10 dating. This discrepancy suggests a question if the Be-10 radiometric method can give us false ages or growth rates (Usui et al., 2002) because of post-depositional change, diffusion or other reasons. In order to answer the question, we conducted ultra-fine magnetostratigraphy with a SQUID microscope on the same hydrogenetic Mn crust sample. Rock magnetic measurements revealed that the main magnetic mineral is well dispersed single domain grains, which is typical to magnetite but not yet specified (Oda, 2005).

Aug 24, 2006

By Katherine H. Walton

The research affiliate projects of the Continental Shelf Division of the Marine Minerals Technology Center concentrate on the development of technologies and methodologies for the exploration 4 and assessment of nonfuel continental shelf mineral resources within the U.S. Exclusive Economic Zone. Three of the FY 1990-91 research grants are summarized below. Scientists at the Center for Applied Isotope Studies at the University of Georgia have developed ?An Advanced Design for a Seafloor Gamma Isotope Mapping System? for the rapid collection of data on seafloor sediments. This system is designed to detect gamma radiation emitted by naturally occurring radioactive elements found in marine sediments. This data can be used to study seafloor lithology and has direct application in marine mineral surveys. The purpose of this study has been to redesign and calibrate the system for marine mineral survey work. Recent modifications of the sled design, gamma radiation detector, and supporting software have resulted in considerable improvements in sensitivity, functional operation, and data acquisition.

Jan 1, 1991

By Gary J. Massoth

Are hydrothermal emissions from subduction-related volcanic arcs important to the total hydrothermal burden of the oceans? While historical observations of hydrothermal venting of fluids at mid-ocean ridgecrests, intra-plate hotspots, and backarc spreading centers are numerous, we remain poorly informed regarding the contributions from hydrothermal systems associated with oceanic submarine arcs. Here we report the chemical results from the first systematic assessment for hydrothermal activity at an intra-oceanic arc front. We discovered that 7 of the 13 submarine volcanoes that define a 260-km-long segment of the southern Kermadec arc north of New Zealand are hydrothermally active. Most significant here is that the chemical compositions of the various hydrothermal systems, inferred from back-extrapolation of observations of hydrothermal plumes, are diverse, and in many instances enriched in the concentrations of gases (e.g., CO2 and H2S) and metals (e.g., Fe and Mn) compared to effluents commonly discharged from mid-ocean ridges. If our results are generally representative of submarine arcs, whose global extent may equal one-third that of ridgecrests, the answer to our leading question could be a resounding yes in terms of both volume and chemical composition.

Jan 1, 2001

By Hans Smit

Start here.

Jan 1, 2018

By Sander van Leeuwen

Outline: · De Regt Marine Cables. · The link between system requirements and umbilical requirements (which system requirements have the largest impact on the umbilical design). · Design options for deep sea mining umbilicals (showing the various options for strength member constructions, power conductors and data-transmission). · Technical challenges and risks (outline on the most important technical challenges and risks involved in the construction, production and usage of deep sea umbilicals). · Umbilicals for the SWORD and Blue Nodules project.

Jan 1, 2018

By Odyssey Marine Exploration

Odyssey is a world leader in marine exploration and has undertaken expeditions in varying environments throughout the world addressing many commercial and regulatory demands. Odyssey works in a variety of settings such as shallow coastal territorial waters, abyssal plains in exclusive economic zones, and high seas in international waters on projects involving mineral exploration, environmental analysis, oceanographic survey, and recovery operations. Odyssey Marine Exploration (Odyssey) excels in adaptively managing programs from initial concept through realization of commercial goals while successfully satisfying the regulatory and engineering demands of deep sea projects. This poster presentation reveals best practices throughout a project life cycle and presents case studies in areas including but not limited to: • Research practices to identify and define valuable subsea resources • Project planning and licensing to achieve project goals and meet regulatory requirements • Optimizing offshore operations to achieve desired results • Designing projects to support processing and commercial programs

Jan 1, 2018

By M. E. Williamson

From December 2004 through March of 2005 an extensive geophysical program was conducted to delineate polymetallic sulfide deposits in the Bismark Sea for a major mining concern. Deeply towed sidescan sonar, interferometric swath bathymetry, subbottom profiling, magnetic gradiometry, electrical resistivity, induced polarization. self-potential, gravimetry, water temperature/conductivity and towed video were among the methodologies tested against known occurrences of polymetallic sulfides in 1500 m -- 2200 m water depths. Known active and currently inactive sulfide areas were characterized using the various remote sensing techniques followed by survey with these same tools in other areas where they successfully discovered new prospects. Dredge sampling was used to ground truth both previously known sulfide areas and newly found deposits.

Jan 1, 2005

By Richard Harrison, Frank Lim

Deepsea Mining will soon become a reality with Nautilus Minerals getting their equipment ready to mine SMS at Solwara 1 off the coast of Papua New Guinea. The vertical transport system (VTS) adopted by Nautilus consists of a riser hanging ‘freely’ from the mining production vessel with a lifting pump unit suspended at its lower end. A compliant jumper connects the pump to the seabed crawler without restraining its movements. In this free-hanging VTS arrangement, the vessel can be re-positioned to follow the crawler should it want to extend the mining area and start stretching the jumper. A recently proposed alternative to this is a free-standing VTS whereby the riser is grounded on the seabed with a base and maintained in an upright position by distributed buoyancy modules or a buoyancy tank at the top. A compliant jumper connects the seabed crawler to the riser base, and another connects the riser top to the vessel. In this free-standing arrangement, the entire VTS can be lifted clear of the seabed for relocation to a new mining area. This paper will describe the important features of the two options and discuss the advantages and disadvantages in respect of riser dynamic behavior, water depth, weather and mining windows, pump maintenance, installation and retrieval, continency measures, etc. The two systems will also be appraised separately for mining SMS and SMnN deposits.

Jan 1, 2018

By Laurie Meyer

The need for improved, high confidence estimates of nodule abundance to support mine permitting, detailed mine planning and mining and processing equipment design is evident. To date, physical samples represent the ?Gold Standard? for nodule abundance measurement, and are likely to remain as such. However, there are some interesting improvements in the area of 3-D scanning which, if marinized for operations at 6000m, may prove to be reliable alternative methods for mapping abundance over large areas particularly if calibrated or benchmarked with physical sample data. . Features of a high confidence physical sampling device, such as the 0.75m2 (0.86m on a side) box corer developed and successfully used by the Kennecott Group for exploration in the CCZ, take into account not only the accuracy in nodule sample collection but a host of other operability considerations which can mean the difference between a successful exploration cruise yielding high numbers of large area samples and one in which few, inaccurate, often inconclusive samples are collected (or, even worse, the sampler fails to grab any nodules for any number of reasons). The collection of physical samples at appropriate spacing within a mine area combined with more qualitative indications of nodule density such as can be obtained using acoustic backscatter should prove adequate for the near term objectives related to overall abundance appraisal or estimates of ?indicated? resource. Looking ahead, exploration cruises will need to yield increasing amounts of data to support development of higher confidence resource abundance estimates to support issuance of mining permits and detailed design of mining plans and equipment. It is likely

Sep 14, 2011

By Laura Moore

The southern shoreline of Monterey Bay, extending from Moss Landing to the Monterey Peninsula, consists of sandy beaches backed by an extensive Flandrian and pre-Flandrian dune complex. This length of shoreline, proximal to areas of urban expansion, is currently being considered for development. For this reason, it is extremely important to understand the variability of beach and dune position along this stretch of coast through time. Previous studies of southern Monterey Bay have documented relatively high erosion rates of 2-8 ft/yr due to a net deficit in the sand budget. Although the sediment transport system in this region is not well understood, estimates for the sediment deficit in southern Monterey Bay range from 200,000 to 1,500,000 yd3/yr. A possible cause of the erosional regime in the southern bay is the removal of sediment by coastal sand mining operations. Based on agency reports and mining permit applications, approximate volumes of sand removed by mining range from 300,000 to 450,000 yd3/yr. These volumes are significant when compared with estimated values for the sediment budget deficit. The sand of southern Monterey Bay, a valuable commercial resource because of its hardness, roundness, amber color and range of usable grain sizes, has been removed from the surf zone, beaches and dunes of Marina and Sand City by four companies since 1906. Information regarding the cross-shore location of sand removal and the exact amounts of sand removal through time is proprietary and poorly documented. However, records documenting the time at which each company commenced and terminated mining do exist. This information suggests that the greatest amount of sand was removed between 1950 and 1968 when three mining companies were operating concurrently.

Jan 1, 1994

By Georgy Cherkashov, Livia Ermakova

Active development of the exploration and further exploitation of deep-sea minerals requires special emphasis on the protection of the marine environment. The complexity of this subject lies in the fact that potential impact and effects of future mining activity are not completely known. One of the main sources of potential impact near the seafloor, as it expected, would be a generation of sediment plumes, their dispersion and redeposition of sediment. Meanwhile, their dimensions, rates of dispersion and redeposition are a big issue. Other plumes are expected in the surface layer as a result of discharges of processing waters and particles after sorting on board of mining vessel, and their features are also not clear. At the same time, understanding of these aspects would be crucial for definition of environment impact area, delineation and designation of different types of protected areas (Areas of Particular Environmental Interest, Impact and Preservation Reference Zones) and future assessment of environmental impacts. Attempts to address these issues demonstrated wide variations between the data of field experiments on the one hand and the results of analytical and numerical models on the other. According to in situ measurements, plumes were detected at a distance vary from one to less than 20 km [e.g., Burns et al., 1980; Sharma et al., 2001; Nautilus Minerals, 2008 etc.], whilst some models show results up to 100 km [Rolinski S. et al., 2001] and more. It seemed that results of in-situ experiments are preferable, but they were not many indeed. However, these data were used in different investigations rather widely, but their focus, as far as we know, was not on the matters related directly with plumes.

Jan 1, 2018

By R. D. Hamer

"The Atlantis II Deposit comprises metalliferous sediments (Zn+Cu+Ag+Au) accumulating in a composite, axial basin, 2,000m beneath the surface of the Red Sea. The basin contains warm, highly saline water. It is located approximately half way between Jeddah and Port Sudan within the Exclusive Economic zones of Saudi Arabia and Sudan. The Deposit was discovered in 1963 and evaluated by drilling in the 1970s and 1980s. This phase defined an initial resource of approximately 90Mt. More recent estimations have refined this figure to an Inferred Resource of approximately 80Mt (CIM compliant).The Mining Licence to develop and extract the Atlantis II Deep Deposit was granted to Manafai International Trade in 2010 by the joint Saudi-Sudanese Red Sea Commission. Manafai is poised to embark on a renewed phase of exploration and evaluation, including the completion of a Definitive Feasibility Study (DFS) and leading to the successful exploitation of the Deposit in a safe, environmentally sound, economically viable and socially responsible manner.The Deposit is forming in a complex basin adjacent the median rift, where sea floor spreading has operated during the last 5Ma. It is a Hydrothermal-sedimentary Deposit. The mineralised sedimentary rocks rest directly on sea floor basaltic rocks. They are produced by the exhalation of metal-rich, hydrothermal brines from fissures associated with the central rift and cross-cutting fracture zones. Up to 25m of metal-rich sediments have accumulated over an area exceeding 57km²."

Jan 1, 2017

By V. Alexandrov

This paper presents the results of theoretical investigations of the energy requirements of the hydraulic lifting of mined materials from the seabed to the sea surface in the deep-sea mining of solid minerals such as manganese nodules in the Clarion-Clipperton region of the Pacific, situated on the sea floor in water depths of 4,500 m or more. The principal element of the developed underwater transport system is the Underwater Chamber, which is connected by flexible pipeline to a mining machine that gathers nodules from the seabed, mixes them with seawater, and feeds them into a flexible pipeline. In this paper, we discuss the question of the optimum water depth for placement of the Chamber, the interior of which is designed to maintain a 1-atmosphere pressure. We present a method for calculating this depth as it relates to the mechanical characteristics of solid particles, the shapes and size distributions of the particles, particle and slurry density, and other properties. These investigations were carried out in hydro-transport laboratory of the Saint-Petersburg Mining Institute and the hydraulic laboratory of Faculty Environmental Engineering in Wroclaw Agricultural University. KEY WORDS: deposit, nodule, flexible pipeline, pressure drop, concentration, hydromixture

Jan 1, 2005

By M. C. I. Modenesi, J. E. Smith, M. Salvá-Ramírez, G. M. Castro, J. C. Santamarina

Annual metal consumption per capita has increased several orders of magnitude worldwide since the turn of the 19th century, yet grades of terrestrial ores are decreasing as reserves dwindle. Consequently, deep sea metal deposits are gradually transitioning from identified resources to economically viable reserves. Deposits in the Red Sea deeps along the axial trough result from tectonic and local hydrothermal processes. Continental rifting and ocean floor spreading produce fresh oceanic crust; concurrently, seafloor evaporites flow into the spreading zone and form isolated deeps. The deeps are often filled with hot stratified brines maintained by locally discharged fluids during hydrothermal circulation. Metalliferous sediments precipitate from the brines within the deeps. The ongoing multipronged study at KAUST involves: (1) acoustic characterization of the metalliferous accumulations using advanced signal processing techniques that capture the physics of granular materials; (2) comprehensive mineralogical and textural characterization of sampled sediments using SEM, EDS, XRD, XRF, and ICP-OES; (3) multiphysics instruments deployed to measure undisturbed sediment properties in-situ; (4) development of a distributed seafloor observatory for monitoring field operations; (5) innovative concentration and separation technologies; and (6) new strategies for proper tailings disposal purposely conceived for the unique field conditions in the Red Sea deeps.

Jan 1, 2018

By Tae-kyeong Yeu

KIOST has developed the pilot mining robot, named MineRo ?? from early-2011 to mid- 2012. The robot consists of two unit-modules having an identical mechanical structure and hydraulic system. One unit-module has two track systems, two pick-up devices, two crushers, one lifting pump and one thruster. The pick-up device is fitted on the frame of the track device. All actuators are driven hydraulically, which are manipulated by valves and the controllers. Each unit-module is equipped with one dual HPU of 250kW / 4,000V. PWM-16 (INNOVA AS) as hydraulic valve controller is adopted, which outputs PWM signals of 16 channels and can be used under pressure in oil-filled box. To measure angular velocity or displacement of hydraulic actuator, turbine-type flow-meters are adopted. The flow-meter has RF (Radio Frequency) type pulse detector, which extends the flow range by eliminating drag on the rotor. Two track motors, two crusher motors, lifting pump, one thruster can be controlled their velocities through feedback of the measured flow-rates. As well as the flow-rates, the states of the hydraulic system such as hydraulic pressures, temperatures, leakages are measured through a self-developed flow-pressure canister. In that canister, multi-channel amplifier boards are installed, through which the vast amount of data is acquired and transmitted to the main controller using serial communication.

Sep 14, 2011

By Steven D. Scott

The 1991 PACMANUS Expedition (Papua New Guinea-Australia-Canada in the Manus Basin) discovered a very large (approximately 800 x 350 m) actively-forming seafloor polymetallic sulfide 4 deposit in felsic volcanic rocks of the southeastern part of Manus Basin, a 60 km wide extensional zone of basalt, andesite and dacite volcanism in the New Britain back arc. The apparent neo-volcanic zone is a 30-km long, high standing, Y-shaped edifice, which we have named Pual Ridge ("Pual" means "fork" in a local PNG dialect). The PACMANUS deposit was found by deep-tow video on Pual Ridge along the flank and adjacent valley of a dacite lava dome. Videos show large spires, chimneys and mounds with abundant fauna. Only two small samples from an active chimney were recovered. Their mineralogy is a high temperature assemblage of chalcopyrite, bornite, tennantite, sphalerite or wurtzite and anhydrite. The bornite and tennantite and silver rich. Gold values for the two samples are 2 and 10 ppm. A pronounced methane and particulate plume was traced in the water column for 14 km to the northeast of the PACMANUS deposit. Other deposits of unknown size are nearby. The deposits of Pual Ridge and their surrounding volcanic rocks have close similarities to ancient massive sulfides of Archean to Phanerozoic age in Canada and Australia.

Jan 1, 2011

By Lénaick Menot, Anne-Sophie Alix, Charline Guérin, Sébastien Ybert, Ewan Pelleter, Florian Besson

Ifremer, on behalf of the French government, holds an Exploration Contract with the ISA for polymetallic nodules in the CCFZ. As part of its exploration activities, the NODULE (2015) cruise was conducted to acquire a 50 m resolution bathymetric coverage of the eastern sectors of the Contract. In 2017, Ifremer initiated an update of the Contract’s mineral resource estimate. Metal grades and nodule abundance were modelled using ordinary kriging. The inferred mineral resource is 436 Mt (wet) of polymetallic nodules at an average abundance of 10.7 kg/m² with a cut-off grade of 7 kg/m². Based on the geological data, seamounts, sedimentary basins and steep slopes contain no nodules. Technical studies of most of the contractors have determined that nodule collectors could not maneuver on slopes above 5 to 10°. Thus, Ifremer has selected a quite conservative slope threshold of 7 % (about 4°) and a backscatter threshold of -29.5 dB to delineate nodule-free areas. This has a significant impact on the resource estimate, as about 54 % of the eastern Contract areas are excluded. Near-seafloor high-resolution mapping and photographic transects, associated with finer-spaced box-core sampling could constitute a next step to better constrain the mineable areas and to get a higher level of confidence in the resource estimation.

Jan 1, 2018